Synthesis,characterization, and evaluation of enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels for colon‐specific drug delivery

The enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels were prepared using 4,4^′‐bis(methacryloylamino)azobenzene (BMAAB) as the crosslinker. It was found that the incorporated N‐isopropylacrylamide (NIPAAm) monomer did not change the enzymatic degradation of hydrogel, but remarkably enhanced the loading of protein drug. The hydrogels exhibited a phase transition temperature between 4°C (refrigerator temperature) and 37°C (human body temperature). Bovine serum albumin (BSA) as a model drug was loaded into the hydrogels by soaking the gels in a pH 7.4 buffer solution at 4°C, where the hydrogel was in a swollen status. The high swelling of hydrogels at 4°C enhanced the loading of BSA (loading capability, ca. 144.5 mg BSA/g gel). The drug was released gradually in the pH 7.4 buffer solution at 37°C, where the hydrogel was in a shrunken state. In contrast, the enzymatic degradation of hydrogels resulted in complete release of BSA in pH 7.4 buffer solution containing the cecal suspension at 37°C (cumulative release: ca. 100 mg BSA/g gel after 4 days). Copyright © 2008 John Wiley & Sons, Ltd.     

Investigation of Water Uptake Behavior of Superabsorbent Polymers Composed of N‐Vinyl‐2‐pyrrolidone and Partially Neutralized Acrylic Acid

Fast‐swelling micrometer sized superabsorbents were synthesized through a rapid solution polymerization of n‐vinyl‐2‐pyrrolidone (NVP) and partially neutralized acrylic acid (PNAAc) under normal atmospheric conditions using N,N'‐methylene bisacrylamide (MB) as crosslinker and sodium bicarbonate as porogen. The effect of various parameters such as crosslinker concentration, degree of neutralization of monomer acid, concentration of initiator have been evaluated. Water retention capacity of superabsorbents under varying loads was also examined. The drying behavior of polymers at 37°C was also studied. The gels showed sharp volume transition in solutions of divalent metal ions. The superabsorbents were also characterized by FTIR and TGA.     

Swelling behavior and network structure of hydrogels synthesized using controlled UV‐initiated free radical polymerization

N‐vinyl‐2‐pyrrolidone (VP) and 2‐hydroxyethyl methacrylate (HEMA) copolymeric gels have been synthesized using UV‐initiated photopolymerization to understand their characteristic behavior for development as a bioengineering material, specifically for tissue expansion. The properties of the gels have been investigated by systematic variation of the monomer feed composition and initiator and crosslinker concentrations as well as UV irradiation intensity, which was controlled by various photomasks. The swelling kinetics and network characteristics for the various hydrogels were investigated through the observation of gel swelling behavior in saline solutions and compression modulus determination of the fully swollen hydrogels. The equilibrium swelling ratio (q_e) of the gels increased as expected with increasing VP content and decreasing crosslinker concentration. However, it was found that as the amount of initiator or UV intensity increased, unexpectedly q_e also increased, which indicates a network structure with decreasing effective crosslink density (ν_e) (or increasing average molecular weight between crosslinks (M_c)). Based on this anomalous swelling behavior and thermal analysis of the gels, a molecular structure is proposed consisting of increasing number of dangling chain ends within the polymer network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1450–1462, 2008     

Specific features of the polyelectrolyte behavior of weakly charged cryogels of polyacrylamide and poly(N-isopropylacrylamide)

Specific features of the polyelectrolyte behavior of weakly charged common gels and cryogels of copolymers of polyacrylamide and poly(N-isopropylacrylamide) with sodium acrylamido-2-methyl-1-propyl sulfonate are investigated. The cryogels are synthesized in frozen solutions at ?15°C. It is shown that the polyelectrolyte swelling is significantly weaker in the case of cryogels than that in the case of gels synthesized in solutions. For thermosensitive gels with isopropylacrylamide groups, collapse occurs during heating. Charging of a common gel leads to a noticeable (18°C) increase in the transition temperature. For a cryogel, this growth is 3°C. During the interaction with cetylpyridinium chloride, the gel contraction is much more pronounced for common weakly charged gels. At the same time, walls of pores of a collapsed cryogel contain a smaller amount of the solvent. Isotherms of the adsorption of a cationic surfactant by anionic common gels and cryogels differ insignificantly. Model gels synthesized in concentrated acrylamide solutions exhibit very weak polyelectrolyte swelling, similar to that of cryogels. The behavior of cryogels is explained by a very high local concentration of crosslinks due to a strong entanglement of polymer chains.     

Thermoresponsive super water absorbent hydrogels prepared by frontal polymerization of N‐isopropyl acrylamide and 3‐sulfopropyl acrylate potassium salt

Super water absorbent polymer hydrogels were synthesized by frontal polymerization. These materials were obtained by copolymerizing N‐isopropyl acrylamide (NIPAAm) and 3‐sulfopropyl acrylate potassium salt (SPAK) in the presence of N,N′‐methylene‐bis‐acrylamide as a crosslinker. It was found that their swelling behavior in water can be easily tuned by using either the appropriate monomer ratio or the amount of the crosslinker used. Namely, the swelling ratio was found to range from about 1000% for the NIPAAm homopolymer in the presence of 5.0 mol % of crosslinker, up to 35,000% for the sample containing 87.5 mol % of SPAK and 1.0 mol % of crosslinker. The affinity toward water was also confirmed by contact angle analysis. Moreover, the obtained hydrogels exhibit a thermoresponsive behavior, with a lower critical solution temperature of about 28–30 °C. This value is close to that of poly(NIPAAm) but with a swelling capability that dramatically increases as the amount of SPAK increases. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and thermal properties of a novel lactose‐containing poly(N‐isopropylacrylamide‐co‐acrylamidolactamine) hydrogel

An improved, simple, and efficient method for the synthesis of lactose‐containing monomer acrylamidolactamine (LAM) has been reported. Free radical copolymerization of this monomer with N‐isopropylacrylamide (NIPAM) in the presence of the crosslinking reagent N,N′‐methylenebisacrylamide (BisA) (1.2 mol %) proceeded smoothly in an aqueous solution using potassium persulfate (KPS) and N,N,N′,N′‐tetramethylethylenediamine (TMEDA) as the initiating system and gave transparent hydrogels. Reactivity ratios were estimated from copolymerization reactions carried out in solution without BisA crosslinker and at low conversion, by using both linearization and nonlinearization methods. They were found to be r_LAM = 0.75 and r_NIPAM = 1.22. The swelling behavior of the hydrogels was studied by immersion of the hydrogels in deionized water at different temperatures. Equilibrium water uptake was increased when the LAM content was higher than 47 mol %, and reached ≈ 44‐fold with 100 mol % LAM at room temperature. Depending on the composition, the gels showed sharp swelling transitions with small changes in temperature. Differential scanning calorimetry (DSC) was used to characterize the swelling transition and the organization of water in the copolymer hydrogels. The amounts of freezable water in these hydrogels ranged from 81 to 89%, and was not correlated to the content of the sugar monomer. These gels have potential applications as biocompatible materials. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1393–1402, 1999     

Thermoresponsive properties of porous poly(N‐isopropylacrylamide) hydrogels prepared in the presence of nanosized silica particles and subsequent acid treatment

Porous poly(N‐isopropylacrylamide) hydrogels were prepared by the free‐radical polymerization of its monomer and a suitable crosslinker in the presence of spherical silica particles of different sizes (74 and 1600 nm) and by the subsequent acid extraction of silica. The yields were 81–83%, and the yields were not affected by the silica content. Scanning electron microscopy observations revealed the porous structure of the hydrogels. Porous and nonporous hydrogels showed volume phase transitions from swelling states to deswelling states at approximately 30 °C, as analyzed by the ratio of the diameter of cylinder‐shaped hydrogels to that of the glass tube used for the hydrogel preparation at the corresponding temperature. Deswelling, which was analyzed by rapid changes in the temperature of the aqueous media from 20 to 40 °C, was facilitated by decreased silica particle size and increased silica content. The deswelling rate constant of the hydrogel prepared with 74‐nm silica at 10 v/v % (silica/solvent) was more than 1500 times greater than that of conventional hydrogels. Swelling was similarly analyzed through changes in the temperature from 40 to 20 °C and was independent of the pore structure. The deswelling–swelling cycle was repeatable with reasonable reproducibility. Moreover, the mechanical strength of the porous hydrogels was significantly maintained compared with that of conventional nonporous hydrogels. This method produced thermoresponsive hydrogels of suitable mechanical strength and remarkable deswelling properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4228–4235, 2002     

Preparation and properties of chitosan‐poly(N‐isopropylacrylamide) semi‐IPN hydrogels

Chitosan (CS), CS‐poly(N‐isopropylacrylamide)(PNIPAM) and their dyed (pyrene) hydrogels were prepared using glutaraldehyde (Glu) as a crosslinker. The gelation rate, swelling behaviors in ethanol/water mixtures, electricity‐induced contraction and thermoresponse of the gels were investigated using fluorescence probe technique. Results showed that CS/Glu, and PNIPAM‐containing CS/Glu gels exhibited similar properties in all aspects examined, except that the transparence of the CS‐PNIPAM/Glu gel is very dependent upon the temperature. The CS‐PNIPAM/Glu gel is transparent below 30°C, whereas opaque above 32°C. It is expected that this observation may be useful for the design and preparation of new kinds of hydrogel devices. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 474–481, 2000     

Copper and Nickel Removal from Aqueous Solutions Using New Chelating Poly[Acrylamide/N‐vinyl pyrrolidone/3‐(2‐hydroxyethyl carbamoyl)acrylic acid] Hydrogels

New poly[Acrylamide/N‐vinyl pyrrolidone/3‐(2‐hydroxyethyl carbamoyl)acrylic acid], poly [AAm/NVP/HECA], chelating hydrogels with different composition of HECA monomer have been prepared via free radical solution polymerization using N,N‐methylene bisacrylamide as a crosslinker. The hydrogels obtained were loaded with metal ions and characterized by FT‐IR spectroscopy, Scanning Electron Microscope (SEM) and Thermogravimatric analysis (TGA). The removal of Cu²⁺ and Ni²⁺ from aqueous solutions by the hydrogel was examined by a batch equilibrium method. The influence of treatment time, pH, initial concentration of the metal ions and HECA content in the feed compositions on the amount of adsorbed metal ions was studied. Swelling of the hydrogel was also carried out in distilled water and metal ion solutions. The removal of the metal ions followed the following order: Ni²⁺>Cu²⁺. The amount of metal ions removed increased with increasing HECA content in the feed composition, treatment time, pH of the medium and initial concentration of metal ions. The desorption of metal ions were carried out using 1 N HCl and 0.5 N H₂SO₄. The poly[AAm/NVP/HECA] hydrogels could be used many times without significantly decreasing their adsorption capacity.     

Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Thermoresponsive super water absorbent hydrogels prepared by frontal polymerization

Frontal polymerization was used as an alternative technique for the preparation of super water absorbent hydrogels obtained from acrylamide and 3‐sulfopropyl acrylate, potassium salt (SPAK) in the presence of N,N′‐methylene‐bisacrylamide as a crosslinker. All samples were synthesized in dimethyl sulfoxide, and their swelling behavior in water was investigated. It was found that their features are dependent on the monomer ratio used, which influenced the porous morphology, and consequently, the swelling capability. The swelling ratio ranges from about 1000% for the acrylamide homopolymer up to 14,000% for the sample containing 87.5 mol % of SPAK, thus indicating that this parameter can be easily tuned by using the appropriate monomer ratio. The affinity towards water was eventually confirmed by contact angle analysis. Polymer hydrogels made from at least 62.5 mol % SPAK exhibit a thermoresponsive behavior, with a lower critical solution temperature of ～30 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2486–2490, 2010     

Novel sulfobetaine‐sulfonic acid‐contained superswelling hydrogels

Novel hydrogels based on zwitterionic monomer [3‐(methacrylamido)propyl] dimethyl (3‐sulfopropyl) ammonium hydroxide (MPDSAH) and a strong acid monomer (2‐acrylamido‐2‐methylpropane sulfonic acid, AMPS) were synthesized through solution polymerization under normal conditions to achieve nearly quantitative gel yield. The structure of the gels was confirmed using infrared spectroscopy. Thermal properties were simultaneously studied by differential scanning calorimetry and thermogravimetric analysis (DSC/TGA). The effects of the polymerization variables on the swelling capacity of the products were investigated. It was found that, in a certain range of the monomers mol ratio, increase of AMPS content was surprisingly accompanied with swelling reduction. The swelling exhibited lower sensitivity to the crosslinker concentration (range 0.6–1.2 wt%) compared with the conventional superabsorbents. However, in contrast with the conventional acrylic acid‐based superabsorbents, the neutralization degree of AMPS part of the new gels had only a small enhancing effect on their swelling capacity. The effect of total monomer concentration on the hydrogel absorbency was also studied. The fully ionic hydrogels showed an unusual pH‐independency behavior, so that their absorbency was nearly unchanged in a wide range of pH. Such unexpected behavior was also observed for the swelling in the ionic environments with various ionic strengths. Copyright © 2005 John Wiley & Sons, Ltd.     

含甲基丙烯酸-N,N-二甲氨基乙酯水凝胶的紫外辐射合成及其性质研究

紫外光辐照 ,H2 O2 为光引发剂 ,N ,N′ 亚甲基双丙烯酰胺为交联剂合成了含甲基丙烯酸 N ,N 二甲氨基乙酯的水凝胶 .研究了水溶液中单体、光敏引发剂、交联剂浓度及光照时间对生成的水凝胶的凝胶含量和溶胀性能的影响 ,给出了最佳合成条件 .用该聚合法合成的聚甲基丙烯酸 N ,N 二甲氨基乙酯水凝胶不仅具有较好的透明性和适当的弹性 ,而且在 40℃和 pH =3时有明显的温度及 pH敏感性 .但离子强度对凝胶溶胀性能没有明显影响     

Pore-size distributions of cationic 2-hydroxyethyl methacrylate (HEMA) hydrogels

Pore-size distributions have been measured for cationic 2-hydroxyethyl methacrylate (HEMA) hydrogels varying in cross-linker/monomer ratio and initial concentration of cationic comonomer MAPTAC, at swelling capacities ranging from 12 to 24 g swollen gel/g dry gel. Swelling capacities were measured at about 6 °C in pure water and in aqueous sodium-azide solutions ranging in concentration from 5 × 10⁻⁴ to 2 × 10⁻¹ M. The mixed-solute-exclusion method (introduced by Kuga) was used to obtain the experimental solute-exclusion curve, representing the amount of imbibed liquid inside the gel inaccessible to a solute of radius r. The pore-size distributions were obtained by using Casassa's Brownian-motion model and numerically solving the Fredholm integral equation. The pore-size distributions shift to higher mode values (57.8-60.9 Å) with decreasing initial cross-linker concentration at the same swelling capacity of about 12. Raising swelling capacities from 11.1 to 23.9 significantly increases the variance from 5.66 × 10³ to 2.67 × 10⁴ Ų. Changes in the concentration of the cationic comonomer MAPTAC do not significantly influence the pore-size distributions.     

Charge‐Functionalized and Structurally Enhanced (Cryo)Hybrids from Acrylic (Co)Monomers and Kaolin: Altering Physicochemical Properties via Cryotropic Gelation

The potential to improve mechanical, structural, and mechanochemical properties of charge‐functionalized poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA)‐based hybrid cryogels is investigated. The simple and versatile synthesis of hybrid cryogels with high strength and toughness using cationic DMAEMA and ionic comonomer 2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid has been proposed via in situ free‐radical crosslinking (cryo)polymerization by which the properties of virgin polymer can be modulated to required applications by incorporation of inorganic filler kaolin (KLN). Two factors affecting swelling and elasticity of hybrid gels (referred as PDA/KLNm), KLN content and gel preparation temperature, are studied. The optimum KLN concentration for desired swelling and modulus of elasticity is determined as 0.80% (w/v). Effective crosslinking density of hybrid hydrogels increases with KLN addition and this dependence is expressed by a quadratic polynomial as a function of KLN concentration. The results show that obtained hybrid gels with multiresponsive properties could be regarded as “smart materials” in sensing and actuation applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1758–1778     

Synthesis of hydrophilic microspheres with LCST close to body temperature for controlled dual‐sensitive drug release

Novel stimuli‐responsive hydrophilic microspheres were prepared by free radical polymerization of hydroxyethyl methacrylate (HEMA) and methacrylic acid (MA), as hydrophilic monomers, and N‐isopropylacrylamide (NIPAAm) and N,N′‐ethylenebisacrylamide (EBA), as thermo‐sensitive monomer and crosslinker, respectively. Hydrophilic comonomers were introduced in the macromolecular network to synthesize materials with tunable thermal behavior. In addition, by introducing in the polymerization feed both a hydrophilic and a pH‐sensitive monomer, such as MA, dual stimuli‐responsive (pH and temperature) hydrogels were synthesized. The incorporation of monomers in the network was confirmed by infrared spectroscopy, while the network density and the shape of hydrogels was found to strictly depend on the concentration of monomers in the polymerization feed. Thermal analyses showed negative thermo‐responsive behavior with pronounced water affinity of microspheres at a temperature lower than lower critical solution temperature (LCST). In our experiment, the LCST values of the hydrogels were in the range 34.6–37.5°C, close to the body temperature, and the amount of hydrophilic moieties in the polymeric network allows to collect shrinking/swelling transition temperatures higher than the LCST of NIPAAm homopolymers. In order to test the preformed materials as drug carriers, diclofenac diethylammonium salt (DDA) was chosen and drug entrapment percent was determined. Drug release profiles, in media at different temperature and pH, depend on hydrogels crosslinking degree and drug–bead interactions. By using semi‐empirical equations, the release mechanism was extensively studied and the diffusional contribute was evaluated. Copyright © 2010 John Wiley & Sons, Ltd.     

Comparative rheological study of ionic semi-IPN composite hydrogels based on polyacrylamide and dextran sulphate and of polyacrylamide hydrogels

Ionic semi-interpenetrating polymer networks composite hydrogels were synthesized by free-radical polymerization using dextran sulphate (DxS), acrylamide as monomer and N,N′-methylene(bis)acrylamide as cross-linking agent. The viscoelastic properties of these composite hydrogels were investigated by oscillatory shear measurements under small deformation conditions comparative with those of polyacrylamide gels. Changes of the rheological properties of composite hydrogels have been studied in terms of polymerization temperature, cross-linker ratio, initial monomer concentration and molar mass of DxS. The results showed that the stability of the composite hydrogels obtained at room temperature (22?°C) was relatively low because the storage modulus (G′) was only eight times higher than the loss modulus (G″), while for those obtained by cryopolymerization (?18?°C), the stability was improved, the G′ values being about 30 times higher than those of G″. This behaviour indicated that, by conducting the synthesis of hydrogels below the freezing point of the reaction solutions, an enhancement of the hydrogels elasticity was achieved. The network parameters, i.e. the average molecular weight between two cross-links and the cross-link density of the composite hydrogels prepared at ?18?°C, were estimated from rheological data.     

The States,Diffusion, and Concentration Distribution of Water in Radiation‐Formed PVA/PVP Hydrogels

Abstract

Hydrogels with various compositions of polyvinyl alcohol (PVA) and poly(1‐vinyl‐2‐ pyrrolidinone) (PVP) were prepared by irradiating mixtures of PVA and PVP in aqueous solutions with gamma‐rays from ⁶⁰Co sources at room temperature. The states of water in the hydrogels were characterized using DSC and NMR T₂ relaxation measurements and the kinetics of water diffusion in the hydrogels were studied by sorption experiments and NMR imaging. The DSC endothermic peaks in the temperature range ?10 to +10°C implied that there are at least two kinds of freezable water present in the matrix. The difference between the total water content and the freezable water content was referred to as bound water, which is not freezable. The weight fraction of water at which only nonfreezable water is present in a hydrogel with F_VP=0.19 has been estimated to be g_H2O/g_Polymer=0.375. From water sorption experiments, it was demonstrated that the early stage of the diffusion of water into the hydrogels was Fickian. A curve‐fit of the early‐stage experimental data to the Fickian model allowed determination of the water diffusion coefficient, which was found to lie between 1.5×10^?11 m² s^?1 and 4.5×10^?11 m² s^?1, depending on the polymer composition, the cross‐link density, and the temperature. It was also found that the energy barrier for diffusion of water molecules into PVA/PVP hydrogels was ≈24 kJ mol^?1. Additionally, the diffusion coefficients determined from NMR imaging of the volumetric swelling of the gels agreed well with the results obtained by the mass sorption method.     

Preparation and swelling properties of hydrolysis-resistant superabsorbent composite based on acrylic acid and sodium bentonite

Abstract

A novel hydrolysis-resistant superabsorbent composite was prepared via the solution polymerization based on acrylic acid (AA) and sodium bentonite (SBT) as monomers, tetraallylammonium bromine (TAAB) as crosslinker and ammonium persulfate (APS) as initiator. The mechanism of polymerization and the structure of the superabsorbent polymer (SAP) were studied by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (X-ray), and scanning electron microscopy (SEM). The reaction conditions such as different mass ratios of APS to AA, TAAB to AA, SBT to AA, neutralization degree of AA were optimized by orthogonal experiment, and the influence of each reaction condition on the capacity of water absorption at 150?°C was investigated via single-factor controlled experiment. The hydrolysis resistance and swelling kinetics of the SAP were studied in different solutions at 150?°C. Compared to traditional SAPs, the SAP synthesized with TAAB as crosslinker performed a more excellent hydrolysis resistance and water absorbency capacity at high temperatures. The water absorbency in distilled water or 0.1?mol L^?1 NaCl solution could reach 392.6 and 145.2?g g^?1at 150?°C, respectively. The SAP maintaining high swelling capacity in the pH range of 5–9 indicated its wide application values in the acidic or alkaline environment at high temperature. In addition, the SAP exhibited good reusability which could still retain about 73% of its initial water absorbency after reswelling six times at 150?°C.     

Photocrosslinking of Polyglycidol and Its Derivative: Route to Thermoresponsive Hydrogels

Hydrogels of biologically well‐tolerated, high‐molar‐mass polyglycidol (PGl) and its thermoresponsive derivative poly(glycidol‐co‐ethyl glycidyl carbamate) have been obtained by direct UV crosslinking in the solid state. Polymers with molar masses up to 1.45 × 10⁶ g mol⁻¹ were crosslinked in the presence of benzophenone or (4‐benzoylbenzyl)trimethylammonium chloride as photosensitizers. The photosensitizer concentration was varied from 2 to 10 wt%. The influence of polymer composition and photosensitizer type and amount on the crosslinking efficiency, swelling and temperature behavior of the obtained hydrogels was investigated. The photocrosslinking of PGl and poly(glycidol‐co‐ethyl glycidyl carbamate) led to hydrogels with swelling degrees up to 1700%. The swelling degrees of the hydrogels decreased with the increase of the environmental temperature indicating the thermoresponsive nature of gels. The swelling of obtained gels can be controlled by varying the composition of the copolymer precursor and by the network density.