THE EFFECT OF CHAIN LENGTH OF POLYETHYLENE GLYCOL ON PROPERTIES OF CASTOR OIL BASED POLYURETHANE ELASTOMERS

ABSTRACT

Polyurethane (PU) elastomers from castor oil based polyol, polyethylene glycol (PEG) of various molecular weight (200, 400, and 600) and toluene diisocyanate were prepared in the form of transparent sheets. The sorption, mechanical and thermal properties have been studied. The solubility parameter, molecular weight between two crosslinks and degree of crosslinking of PU samples were calculated from equilibrium swelling experiments. The kinetic study of swelling revealed that sorption is anomalous in nature in all the samples. Diffusion coefficient (D) and sorption coefficient (S) were found to decrease with an increase in chain length of PEG. The stress-strain data showed that the elastomers obtained using PEG-200 gave the best mechanical properties. The thermal degradation of all elastomers starts at ～250°C, regardless of the PEG chain length. The values of activation energy of degradation were in the range of 60–72 kJ/mole.     

Mechanical properties of solvolysis lignin-derived polyurethanes

In order to study the tensile properties of solvolysis lignin polyurethanes, polyurethane (PU) films were prepared from the solvolysis lignin (SL)–polyethylene glycol (PEG)–diphenylmethane diisocyanate (MDI) system, and in addition to this further PU films were also prepared from the SL–MDI system. In the SL–PEG-MDI system, the SL content, the molecular weight of PEG and the NCO:OH ratio were varied in order to control the physical properties. The tensile stress and Young's modulus of the PUs of the SL–PEG–MDI type increased with increasing SL content and NCO:OH ratio. The tensile properties of the PUs from the SL–MDI system showed no NCO:OH ratio dependency; i.e. the mechanical properties of PUs are not influenced by the change in crosslinking. It is possible to control the tensile properties of PUs of the SL–PEG–MDI type by changing the content of PEG and SL at a constant NCO:OH ratio.     

Determination of molecular parameters of NR/PU block copolymers by transport studies

The equilibrium swelling experiments of block copolymers based on natural rubber (NR) as soft segment and polyurethane (PU) derived from toluene diisocyanate (TDI) and 1,3-butane diol (1,3-BDO) as hard segment were performed in various solvents. Block copolymers with different NCO/OH ratio, viz., from 1.26 to 1.96 were employed in this study. The crosslink densities are found to vary with the NCO/OH ratio employed in the synthesis of the samples. The sorption behaviour is also found to vary with the NCO/OH ratio. The equilibrium swelling experiments have been used to determine the molecular parameters such as molecular mass between crosslinks, crosslink density, polymer-solvent interaction parameter, etc. The equilibrium swelling values were also used to calculate the solubility parameter values of the block copolymers.     

Efficacy of clay content and microstructure of curing agents on the structure–property relationship of new‐generation polyurethane nanocomposites

The physicomechanical properties of new polyurethanes (PUs) derived from toluene diisocyanate, poly(propylene glycol), and cured by third‐generation hyperbranched polyester polyol (HB3), trimethylolpropane (TMP), or glycerol and their nanocomposites have been investigated. An apparent microphase‐segregated morphology of PU nanocomposites cured by HB3 has been observed by transmission electron microscopy and atomic force microscopy. Morphological studies reveal regions of mostly exfoliated and some intercalated morphology in the case of the nanocomposites, which have been further ascertained by X‐ray diffraction analysis. The HB3‐cured PU nanocomposite containing 8 wt% of modified montmorillonite (Cloisite 30B) clay shows approximately 140% increase in tensile strength along with improvement in thermal and dynamic mechanical properties in comparison with the control hyperbranched PU. It has also been found from Fourier transform infrared spectroscopy analysis that the extent of tethering reactions between the polymer chains carrying residual –NCO groups and the reactive hydroxyl (?OH) groups of HB3 is significant, and the nanofiller has been found to preferentially react with the –NCO group of the prepolymer. Furthermore, the properties of HB3‐cured PU have been compared with the glycerol and TMP‐cured PUs and their nanocomposites. The physicomechanical and thermal properties for nanocomposites of HB3‐cured PUs are superior to those of the conventionally cured PUs. Copyright © 2011 John Wiley & Sons, Ltd.     

Filling of Castable Polyurethanes with Solid Wastes from Petrochemical Production

Physicochemical properties of castable polyurethanes based on polyethylene glycol adipate and mixture of 2,4- and 2,6-toluylene diisocyanate (NCO : OH molar ratio 1.6) and filled to 10 wt % with silica gel (waste from petrochemical production) were studied.     

Interpenetrating polymer network from castor oil-based polyurethanes and poly(methyl methacrylate). XV

The polyurethanes have been prepared from 2.12 functional ? OH containing castor oil and diphenyl methane diisocyanate under identical experimental conditions with a varying NCO/OH ratio. These polyurethanes were swollen in methyl methacrylate and subsequently interpenetrated by free radical polymerization using benzoyl peroxide and crosslinker ethylene glycol dimethacrylate. A series of interpenetrating polymer network (IPN) PU/PMMA IPNs were obtained as films by a transfer moulding technique. These IPNs were characterized by their resistance to chemical reagents, thermal behavior, and mechanical properties. The morphology was shown by SEM and dielectric properties at different temperatures were measured.     

Thermal properties of solvolysis lignin-derived polyurethanes

Thermal properties of polyurethane (PU) films prepared from solvolysis lignin (SL), polyethylene glycol (PEG) and diphenylmethane diisocyanate (MDI) were examined by differential scanning calorimetry and thermogravimetry. In the SL—PEG—MDI system, the SL content, the molecular weight (M_n) of PEG and the NCO/OH ratio were changed in order to control the thermal properties. Glass transition temperatures (T_g's) of the prepared PU's were dependent on the SL content, the M_n of PEG and the NCO/OH ratio. However, the T_g of PU was significantly influenced by the SL content: the increment of T_g was ca. 150 K when the SL content in PEG increased from 0 to ca. 50%. The decomposition of the PU's was markedly dependent on the content of SL. Other factors, such as the NCO/OH ratio and the M_n of PEG, are less dominant compared with the SL content. This fact suggests that the dissociation between the isocyanate groups and the phenolic OH groups in SL may be the major factor in the whole process of the thermal decomposition of the PU containing SL     

Detection of toluene diisocyanate in air with a coated piezoelectric crystal: Part 1. A Study of Coating Materials

A method for the detection of toluene diisocyanate vapour down to its threshold limit value (0.02 ppm) is presented; the sorption of the vapour onto a piezoelectric quartz crystal coated with polyethylene glycol is utilized. The resulting change in weight of the crystal is monitored by the associated change in the oscillation frequency. An investigation into the nature of the sorption process is described, and different coatings and chemical modifications to the PEG to minimize the effect of water vapour are indicated.     

Interpenetrating polymer networks from polyurethanes and methacrylate polymers. I. Effect of molecular weight of polyols and NCO/OH ratio of urethane prepolymers on properties and morphology of IPNs

Two types of reinforced elastomeric interpentrating polymer network (IPN) were prepared by simultaneous polymerization and crosslinking in solution. The first type consisted of polyurethane-poly(methyl methacrylate) (PU/PMMA), and the second, of polyurethane-poly(methyl methacrylate-methacrylic acid) PU/P(MMA–MAA) of constant composition (90/10) and (80/20) by weight, respectively. The members of each type differed in the NCO/OH ratio of the PU prepolymer and the molecular weight (MW) of the polyol in the PU component because we wished to investigate systematically the effect of changing the NCO/OH ratio and MW of the polyol on the mechanical properties and morphology of the resulting IPNs. The mechanical properties, particularly the modulus of both tyes of IPN, increased with increasing NCO/OH ratio and decreased with increasing MW of the polyol in the PU. The morphology of the IPNs was studied by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Improved phase compatibility and decreasing extent of phase separation was observed in both types of IPN with increasing NCO/OH ratio and decreasing MW of the polyol used in the PU. These results may imply that improved interpenetration results from increasing the NCO/OH ratio and decreasing the MW of the polyol in the PU component. The fact that the effect is more pronounced with the type of PU-P(MMA–MAA) IPN can be rationalized as due to the additional hydrogen bonding between the carbonyl in the carboxyl groups and the urethane or urea groups in the PU component.     

不同异氰酸酯固化的蓖麻油／酚氧树脂聚氨酯的力学性能

以ＢＦ３·ＯＥｔ２为催化剂，４，４－二羟基二苯基丙烷与环氧氯丙烷反应，生成端羟基的酚氧树脂（Ａ），Ａ与蓖麻油（Ｂ）混合，用３种异氰酸酯（ＴＤＩ、ＩＰＤＩ和ＨＤＩ）作为固化剂，制得交联聚氨酯。研究了这３种聚氨酯的力学性能及形态与组成和二异氰酸酯结构的关系；改变ＮＣＯ／ＯＨ摩尔比及Ｂ与Ａ的质量比，可以制得具有较好力学性能的聚氨酯材料。蓖麻油，酚氧树脂，聚氨酯，力学性能     

Preparation of polyurethane dispersions by miniemulsion polymerization

With a two‐step miniemulsion polymerization, hydrophobic polyurethane (PU) dispersions were prepared with a cosurfactant, the costabilizer hexadecane (HD) in the oil phase, and sodium dodecyl sulfate (SDS) in the water phase. The first step involved the formation of NCO‐terminated prepolymers between isophorone diisocyanate and poly(propylene glycol) oligomer in toluene. Next, PU dispersions were produced by a miniemulsion method in which an oil phase containing NCO‐terminated prepolymers, HD, the chain extender 1,4‐butanediol (BD), the crosslinking agent trimethylol propane (TMP), and the catalyst dibutyltin dilaurate was dispersed in the water phase containing SDS. The influence of experimental parameters, such as the ultrasonication time, concentrations of SDS and HD, and TMP/BD and NCO/OH equivalent ratios, on the sizes of the miniemulsion droplets and polymer particles, as well as the molecular weights and thermal properties of the PU polymer, was examined. The chemical structure of the produced PU polymer was identified with a Fourier transform infrared spectrometer. The molecular weight distribution and average particle size were measured through gel permeation chromatography and dynamic light scattering, respectively. The thermal stability of the PU polymer was characterized with thermogravimetric analysis. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4870–4881, 2005     

Synthesis and properties of room temperature curable trimethoxysilane‐terminated polyurethane and their dispersions

The purpose of this research is to study the synthesis and characterization of stable aqueous dispersions of externally chain extended polyurethane/urea compositions terminated by hydrolyzable or hydrolyzed trialkoxysilane groups incorporated through secondary amino groups. These dispersions with excellent storage stability are substantially free from organic solvents which cure to water and solvent resistant, tough, scratch resistant, preferably light stable (non‐yellowing) silylated polyurethane (SPU) films. The films were characterized by FT‐IR, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile strength and water contact angle measurements, nanoindentation, gel content, water and xylene swellability tests. The properties of the films were discussed and correlated in detail by changing length of soft segment, diisocyanates, NCO/OH ratio and chain extender, ethylenediamine (EDA). From the results, it was found that the particle size and viscosity are lower whereas the gel content and thermal stability are higher for SPUs. Modulus, hardness and tensile properties of SPU films are superior compared to EDA‐PU film. Higher water contact angle and residual weight percentage of SPU films confirm silylation of PU by [3‐(phenylamino)propyl]trimethoxysilane (PAPTMS). Increase in NCO/OH ratios consumes more quantity of PAPTMS which makes PU with superior mechanical properties. Higher PAPTMS content in SPU results in effective crosslinking of the functional silanol groups formed by hydrolysis reaction of trimethoxysilane groups. Overall, SPUs synthesized at 1.4 NCO/OH ratio using Poly‐(oxytetramethylene)glycol (PTMG)‐2000 and isophorone diisocyanate (or) toluene‐2,4‐diisocyanate have excellent properties compared to SPUs prepared using PTMG‐1000 and at 1.2 and 1.6 NCO/OH ratios. SPUs prepared at 1.6 NCO/OH ratio are brittle due to higher crosslinking density. In addition, the crosslinking density of the films can be modified through silane end‐group modification to produce SPUs with a wide range of physical properties. Copyright © 2007 John Wiley & Sons, Ltd.     

Study on Reaction of Tolylene Diisocyanate with Polyolefine Polyols

Polyurethane(PU) has been used widely. It is produced by polyisocyanate with polyol. There are many polyisocyanates and polyols. For polyols it is mainly concentrated on polyester and polyether, there is any study on polyolefine polyol. The paper mainly discuss it.By using tolylene diisocyanate(TDI,C6H4CH3(NCO)2) to react with hydroxyterminated polybutadiene(HTPB,HO-[-CH2-CH=CH-CH2-]n-OH,Mn=3805,) and hydroxy-terminated poly(butadiene-co-acrylonitrile)(HTBN, HO-[(-CH2-CH=CHCH2-)x-(-CHCN-CH2)y-]n-OH,Mn=2267), various NCO/OH equivalent ratio NCOterminated polyurethane(PU) prepolymers are synthesized.     

Effect of molecular weight of PEG soft segments on photo-stimulated self-healing performance of coumarin functionalized polyurethanes

Polyurethanes consisting of tri-functional homopolymer of hexamethylene diisocyanate （tri-HDI） and polyethylene glycol （PEG） are synthesized, in which photo-reversible coumarin moieties act as pendant groups. Accordingly, the polyurethanes can be repeatedly self-healed under UV lights at room temperature by taking advantages of the photodimerization and photocleavage habits of coumarin. Molecular weight of the soft segment, PEG, is found to be closely related to the healing performance of the polyurethanes. Lower molecular weight PEG that corresponds to higher initial coumarin concentration in the polymer is critical for obtaining higher healing efficiency in the case of the first healing action. Nevertheless, it does not guarantee high reversibility of the photo-remendability during the repeated healing events. In contrast, the polyurethane with moderate molecular weight PEG has achieved balanced performance. Reaction kinetics is less important for the healing effect.     

Swelling equilibrium and sorption kinetics of urethane-modified bismaleimides elastomer

The swelling equilibrium and diffusion kinetics in various solvents of the maleimide-terminated polyurethanes (UBMIs) and of the triol and tetraol-crosslinked polyurethanes (PU) were studied. The polymer volume fraction of the UBMIs at swelling equilibrium is much higher than that of the tetraol-crosslinked PU networks for the same type of polyol used in the PU. It was explained by the high functionality of the UBMIs produced in the network structure. Furthermore, the molecular weight between crosslinks (M_c) has been calculated from the swelling model and the results exhibit good agreement with the proposed network structure. The early time sorption kinetic data were obtained to investigate the diffusion mechanism of the solvent in the networks. The solubility, diffusion coefficients, and permeability of the solvent in UBMI networks were found to be lower than in the multiol-crosslinked PU networks. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1747–1755, 1997     

聚醚聚氨酯/环氧树脂互穿网络聚合物的研究(Ⅱ)

合成了不同类型聚醚聚氨酯/环氧树脂(PU/EP)互穿网络聚合物(IPN),通过改变PU中聚乙二醇分子量、3OH/2OH及NCO/OH比值等,研究IPN组份间分子混合程度,采用电镜、动态力学分析及应力应变等测试方法表征。结果表明:聚乙二醇分子量降低及3OH/2OH、NCO/OH比的提高,可使相容性提高,材料力学性能增强。     

Microencapsulated ammonium polyphosphate with polyurethane shell: preparation,characterization, and its flame retardance in polyurethane

A series of polyurethane (PU) microencapsulated ammonium polyphosphate (MCAPP) were prepared by in situ polymerization from toluene‐2,4‐diisocyanate (TDI), polyethylene glycol (PEG), and pentaerythtritol (PER). And the structure was characterized by Fourier transform infrared spectroscopy (FTIR) and X‐ray photoelectron spectroscopy (XPS). Then it chose the optimal PEG constituent to design microcapsule from scanning electron microscopy (SEM) and water solubility test. The combustion and thermal degradation behaviors of PU blended APP or MCAPP were investigated by thermogravimetric analysis (TGA), UL‐94 test, and microcombustion calorimetry. The results showed that the PU/MCAPP had better thermal stability and flame retardance, due to the stable char forming by APP and PU shell. Moreover, the water resistance of flame retarded PU composite was greatly improved. Copyright © 2009 John Wiley & Sons, Ltd.     

丝素蛋白-聚氨酯复合水凝胶的制备及性能研究

以聚乙二醇(PEG)、聚氧化丙烯二醇(PPG)、异弗尔酮二异氰酸酯(IPDI)为主要原料制备聚氨酯预聚体(PU),与丝素蛋白水溶液(SF)交联制得丝素蛋白-聚氨酯(SF-PU)复合水凝胶.分别利用ATR、SEM对水凝胶组成、结构及微观形貌进行表征;DSC、吸水溶胀测试探讨了丝素蛋白与聚氨酯的质量比(SF/PU)以及聚氨酯中不同软段质量比(PEG/PPG)对SF-PU水凝胶热性能、溶胀性能的影响.结果表明,SF-PU水凝胶具有多孔结构;样品中不同的SF/PU、PEG/PPG均对材料的玻璃化转变温度、结晶度及溶胀性能产生影响,且当水凝胶组分为SF/PU=1/25、PEG/PPG=2/1时,平衡溶胀比(ESR)可达到440%;水凝胶在溶胀初始阶段符合菲克扩散模型,整个溶胀过程遵循溶胀动力学2级方程.     

Investigation of thermal,mechanical, and electrical properties of novel polyurethanes/high molecular weight polybenzoxazine blends

In order to prepare tough polyurethane (PU) electrical insulator with improved thermal stability and electrical insulating properties, high molecular weight polybenzoxazine precursor was mixed and co‐cured with crosslinkable urethane prepolymers. Polybenzoxazine precursor (Bmda) was synthesized from reaction of bisphenol‐A, methylenedianiline, and paraformaldehyde. Epoxy‐terminated polyurethanes (EPU1‐4) were prepared by the reaction of glycidol with NCO‐terminated urethane oligomers. The oligomers were prepared from different molecular weight versions of polycaprolactone polyol (CAPA) and hexamethylene diisocyanate. Blends were prepared through thermal treatment of equal weights of two precursors dissolved in chloroform. Optimum curing condition was determined by DSC and DMTA analysis and measurement of the gel content for cured samples. Viscoelastic, thermal, mechanical, and electrical properties of cured samples were investigated and structure–property relationship was established. Copyright © 2008 John Wiley & Sons, Ltd.     

Poly(Urethane)-Crosslinked Poly(HEMA) Hydrogels

Abstract

Hydrogels have been prepared from 2-hydroxyethyl methacrylate polymerized in the presence of isocyanate-terminated poly(ethylene glycol) (PEG) crosslinking agents. PEGS of molecular weights 200, 400, and 1000 were investigated. The crosslinked nature of the hydrogels was demonstrated by their insolubility in solvents which normally dissolve poly(HEMA). Hexamethylene diisocyanate (HDI) was mainly used as the isocyanate. The molecular weight of the PEG and the crosslinker content significantly influenced the equilibrium water sorption and mechanical properties of the saturated networks. It was observed that as the molecular weight of the PEG increased, the water sorption increased and the nominal modulus decreased. However, for higher levels of cross-linker, water sorption decreased and modulus increased at low molecular weight PEG; for PEG 1000, water absorption increased as crosslinker content increased. These results are explained by the competing effects of flexibility, crosslink density, and hydrophobicity contributed by the various constituents of the hydrogels.