Nanofibrous polyaniline thin film prepared by plasma‐induced polymerization technique for detection of NO2 gas

A nanofibrous polyaniline (PANI) thin film was fabricated using plasma‐induced polymerization method and explored its application in the fabrication of NO₂ gas sensor. The effects of substrate position, pressure, and the number of plasma pulses on the PANI film growth rate were monitored and an optimum condition for the PANI thin film preparation was established. The resulting PANI film was characterized with UV–visible spectrophotometer, FTIR, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The PANI thin film possessed nanofibers with a diameter ranging from 15 to 20 nm. The NO₂ gas sensing behavior was studied by measuring the change in electrical conductivity of PANI film with respect to NO₂ gas concentration and exposure time. The optimized sensor exhibited a sensitivity factor of 206 with a response time of 23 sec. The NO₂ gas sensor using nanofibrous PANI thin film as sensing probe showed a linear current response to the NO₂ gas concentration in the range of 10–100 ppm. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Polyindole/Poly(vinyl acetate) Conducting Composites

Composites of a polyindole (PIN) and poly(vinyl acetate) (PVAc) were prepared chemically using FeCl₃ as an oxidant agent in anhydrous media. The composite compositions were altered by varying the indole monomer during preparation. The composites were characterized by FTIR and UV‐visible spectroscopies, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), stress‐strain experiments and conductivity measurements. Moreover, the film of PVAc and PIN/PVAc composites were prepared by casting on glass Petri dishes to examine their stress‐strain properties. PIN/PVAc composites are thermally more stable than PIN. It was found that the conductivities of PIN/PVAc composites depend on the indole content in the composites.     

Photosensitivity of CuBiSe2 Thin Film Deposited by Vacuum Evaporation Technique

CuBiSe₂ (CBSe) thin film was prepared by vacuum evaporation. The deposited film was characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), energy dispersive X‐ray (EDX), UV–visible specroscopy, and I–V analysis. XRD analysis indicates the formation of cubic CBSe thin film, and the corresponding EDX spectrum confirms the stoichiometry composition of CBSe. In the AFM images, the majority of the particles are granular, and the surface roughness is 8.86 nm. The optical absorption coefficient is >10⁴ in the visible region and the bandgap energy is calculated to be 1.84 eV. The photosensitivity of the film is 181%.     

Influence of thermal annealing on the structural and optical properties of maghemite (γ‐Fe2O3) nanoparticle thin films

In this study, maghemite (γ‐Fe₂O₃) nanoparticles were initially synthesized via chemical co‐precipitation and then deposited by spray pyrolysis as thin films on white glass substrates. The thin films were annealed for 8 h at 400, 450, 500, 550, and 600 °C in an oven. The structural studies of maghemite nanoparticles were carried out using X‐ray diffractometer. Structural properties that we investigated by X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, SEM, and Energy dispersive X‐ray analysis (EDS). Optical properties of the samples were also investigated by ultraviolet‐visible (UV–vis) spectroscopy. The results showed that maghemite nanoparticles have crystalline structure with domain that increases in size with increasing annealing temperature. The optical band gap values were found to reduce from 2.9 to 2.4 eV with increase in annealing temperature. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis of amphiphilic graft copolymer brush and its use as template film for the preparation of silver nanoparticles

A microphase‐separated, amphiphilic graft copolymer consisting of a poly (vinyl chloride) (PVC) backbone and poly(oxyethylene methacrylate) (POEM) side chains, (PVC‐g‐POEM at 62:38 wt %) was synthesized via atom transfer radical polymerization (ATRP). Nuclear magnetic resonance (¹H NMR), FTIR spectroscopy, and transmission electron microscopy (TEM) clearly revealed that the “grafting from” method using ATRP was successful and that the graft copolymer molecularly self‐assembled into discrete nanophase domains of continuous PVC and isolated POEM regions. The self‐assembled graft copolymer film was used to template the growth of silver nanoparticles in solid state by introducing a AgCF₃SO₃ precursor and a UV irradiation process. The in situ formation of silver nanoparticles in the graft copolymer template film was confirmed by TEM, UV–visible spectroscopy, and wide angle X‐ray scattering. FTIR spectroscopy and X‐ray photoelectron spectroscopy also demonstrated the selective incorporation and in situ formation of silver nanoparticles within the hydrophilic POEM domains, presumably due to strong interactions between the silver and the ether oxygen in POEM. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3911–3918, 2008     

Facile synthesis for well‐defined A2B miktoarm star copolymer of poly(3‐hexylthiophene) and poly(methyl methacrylate) by the combination of anionic polymerization and click reaction

We have introduced a facile synthetic route for well‐defined A₂B miktoarm star copolymer composed of regioregular poly(3‐hexylthiophene) and poly(methyl methacrylate) ((P3HT)₂PMMA) by the combination of anionic polymerization and click reaction. First, we synthesized PMMA terminated with 1,3,5‐tris(bromomethyl)benzene (PMMA‐(Br)₂) by anionic polymerization, and two bromines attached to the end of the PMMA chains were replaced by azides (PMMA‐(N₃)₂). Also, monoethynyl‐capped P3HT was synthesized by Grignard metathesis polymerization and post‐end functionalization. Then, copper(I)‐catalyzed Huisgen 1,3‐dipolar cycloaddition click reaction between monoethynyl‐capped P3HT and PMMA‐(N₃)₂ was performed to synthesize (P3HT)₂PMMA. We used a slightly excess amount of monoethynyl‐capped P3HT so that all of the azide groups at the end of the PMMA chains completely reacted with monoethynyl‐capped P3HT. After complete removal of unreacted monoethynyl‐capped P3HT by column chromatography, pure (P3HT)₂PMMA with narrow molecular weight distribution (the polydispersity of 1.18) was obtained. The weight fraction of P3HT and the total molecular weight of (P3HT)₂PMMA are 0.48 and 16,000, respectively. To investigate the effect of the chain architecture on optical property and thin‐film morphology, we synthesized two linear P3HT‐b‐PMMAs (P3HT‐b‐PMMA‐L and P3HT‐b‐PMMA‐H) with similar weight fraction of P3HT block (0.48 for P3HT‐b‐PMMA‐L and 0.45 for P3HT‐b‐PMMA‐H) but two different total molecular weights (7900 for P3HT‐b‐PMMA‐L and 15,300 for P3HT‐b‐PMMA‐H). UV–visible (UV–vis) absorption spectrum and the fibril width of (P3HT)2PMMA thin film were similar to those of P3HT‐b‐PMMA‐L thin film. However, UV–vis spectrum for P3HT‐b‐PMMA‐H thin film was red‐shifted and the fibril width of P3HT‐b‐PMMA‐H was much larger than that of (P3HT)₂PMMA. This indicates that the π–π interaction between P3HT arms in (P3HT)₂PMMA is strong enough to arrange two P3HT backbone chains in (P3HT)₂PMMA to stack one by one along the nanofibril axis. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Molecular Assembly by Sequential Ionic Adsorption of Nanocrystalline TiO2 and a Conjugated Polymer

Abstract

Cationic nanocrystalline TiO₂ particles have been synthesized for which the size and composition of the nanoparticles were analyzed by a transmission emission microscopy and energy dispersive x‐ray spectrometer (EDXS). Multilayered films have been fabricated by sequential adsorption of TiO₂ nanoparticles and poly(3‐thiophene acetic acid) (PTAA). Each layer of the nanoparticles and PTAA in the thin film has also been characterized by x‐ray photoelectron spectroscopy, atomic force microscopy, and UV‐visible spectroscopy. These types of multilayered nanocomposite films may find applications in the fabrication of efficient light harvesting photovoltaic cells.     

Synthesis and characterization of poly(benzodithiophene) derivative for organic thin film transistors

Poly{2,6‐bis(3‐dodecylthiophen‐2‐yl) benzo[1,2‐b;4,5‐b′]dithiophene} (PTBT) was synthesized, via oxidative polymerization by oxidative agent (FeCl₃). The mole ratio of FeCl₃ and monomer (3.5:1), and keeping low temperature during the dropping of diluted catalyst were very important for the polymerization without crosslinking. The PTBT was confirmed by ¹H NMR, FTIR spectra, and elemental analysis. The PTBT has very good solubility in organic solvents such as chloroform, tetrahydrofuran, etc, and good thermal stability with T_g of 164 °C. The PTBT shows UV‐optical absorption at 406 nm and photoluminescence (PL) spectroscopy at 504 nm in a film. The highest occupied molecular orbital (HOMO) energy of the polymer is ?5.71 eV by measuring cyclic voltammetry (CV). A solution‐processed polymer thin film transistor device shows a mobility of 3 × 10^?5 – 8 × 10^?5 cm² V^?1 s^?1, and an on/off current ratio of 10⁴. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5277–5284, 2007     

Templated synthesis of silver nanoparticles in amphiphilic poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) comb copolymer

In this study, poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(oxyethylene methacrylate), P(VDF‐co‐CTFE)‐g‐POEM, an amphiphilic comb copolymer with hydrophobic P(VDF‐co‐CTFE) backbone and hydrophilic POEM side chains at 73:27 wt % was synthesized. The POEM side chains were grafted from the P(VDF‐co‐CTFE) mainchain backbone via atom transfer radical polymerization (ATRP) using direct initiation of the chlorine atoms in CTFE units. Synthesis of microphase‐separated P(VDF‐co‐CTFE)‐g‐POEM comb copolymer was successful, as confirmed by nuclear magnetic resonance (¹H NMR), FTIR spectroscopy, and transmission electron microscopy (TEM). Nanocomposite films were prepared using the comb copolymer as a template film and the in situ reduction of AgCF₃SO₃ precursor to silver nanoparticles under UV irradiation. Silver nanoparticles with 4–8 nm in average size were in situ created in the solid state template film, as revealed by TEM, UV–visible spectroscopy, and wide angle X‐ray scattering (WAXS). Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) presented the selective incorporation and the in situ growth of silver nanoparticles within the hydrophilic POEM domains of microphase‐separated comb copolymer film. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 702–709, 2008     

Comparison of electrochemical properties of two-component C60-Pd polymers formed under electrochemical conditions and by chemical synthesis

The electrochemical behavior of C₆₀-Pd polymer formed under electrochemical conditions and by the chemical synthesis was examined. In these polymers, fullerene moieties are covalently bonded to palladium atoms to form a polymeric network. Both materials deposited at the electrode surface show electrochemical activity at negative potentials due to the reduction of fullerene cage. Electrochemically formed thin polymeric films exhibit much more reversible voltammetric response in comparison to chemically synthesized polymers. The morphology and electrochemical behavior of chemically synthesized C₆₀-Pd polymer depend on the composition of grown solution. Chemical polymerization results in formation of large, ca. 50 μm, crystallic superficial structures that are composed of regular spherical particles with a diameter of 150 nm. The capacitance properties of C₆₀-Pd films were investigated by cyclic voltammetry and faradaic impedance spectroscopy. Specific capacitance of chemically formed films depends on the conditions of film formation. The best capacitance properties was obtained for films containing 1:3 fullerene to Pd molar ratio. For these films, specific capacitance of 35 Fg^?1 was obtained in acetonitrile containing (n-C₄H₉)₄NClO₄. This value is much lower in comparison to the specific capacitance of electrochemically formed C₆₀-Pd film.     

High‐performance Flexible Complementary Electrochromic Device Based on Plasma Modified WO3 Nano Hybrids and V2O5 Nanofilm with Low Operation Voltages

Tungsten trioxide‐poly(3,4‐ethylenedioxythiophene) (WO₃‐PEDOT) and tungsten trioxide‐polyfuran (WO₃‐PFu) were prepared by rf rotating plasma polymerization. Electrochromic hybrid thin films were fabricated onto flexible polyethylene terephthalate (PET)/ indium tin oxide (ITO) film using electron beam evaporation method. In order to deeply characterize all films, scanning electron microscopy‐energy dispersive X‐ray spectroscopy (SEM‐EDS) and electrochemical impedance spectroscopy (EIS) techniques were used. The counter electrode effect on plasma modified WO₃ nano hybrids‐based electrochromic devices (ECDs) was evaluated. By incorporating flexible vanadium pentoxide (V₂O₅) film as counter electrode, complementary ECDs were constructed through combining the hybrid flexible films (WO₃‐PEDOT, WO₃‐PFu) as working electrodes, which exhibit highly efficient electrochromic performance with low voltage operation. Especially, WO₃‐PEDOT/V₂O₅‐based ECD owns a high optical modulation of 61.5 % at 750 nm driven by −1.0 V (coloration) and +1 V (bleaching) with fast response times (coloration time: 13.58 s, bleaching time: 8.07 s) and a high coloration efficiency of 527 cm² C⁻¹. This study can supply useful and efficient avenue for designing flexible complementary electrochromic device for energy‐saving flexible electronics.     

Processable and Robust MoS2 Paper Chemically Cross‐Linked with Polymeric Ligands by the Coordination of Divalent Metal Ions

Inorganic graphene analogues (IGAs) are a huge and fascinating family of compounds that have extraordinary electronic, mechanical, and thermal properties. However, one of the largest problems that face the industrial application of IGAs is their poor processability, which has led to a “bottlenecking” in the development of freestanding, large‐area, IGA‐based thin‐film devices. Herein, we report a facile and cost‐efficient method to chemically modify IGAs by using their abundant coordination atoms (S, O, and N). Taking MoS₂ as an example, we have prepared homogeneous “solution” systems, in which MoS₂ nanosheets are chemically cross‐linked through a carboxylate‐containing polymeric ligand, poly(methyl methacrylate) (PMMA), by copper‐ion coordination. Bonding interactions between C?O bonds and sulfur atoms through copper ions were confirmed by various characterization techniques, such as UV/Vis, FTIR, and Raman spectroscopy and XPS. By using our method, freestanding MoS₂ paper with significantly improved mechanical properties was obtained, thus laying the basis for the mass production of large‐area MoS₂‐based thin‐film devices. Furthermore, copper‐ion coordination was also applied to MoS₂/PMMA nanocomposites. Direct and strong nanofiller/matrix bonding interactions facilitate efficient load transfer and endow the polymeric nanocomposites with an excellent reinforcement effect. This method may pave a new way to high‐strength polymeric nanocomposites with superior frictional properties, flame retardance, and oxidation resistance.     

Plasma-Polymerized Thin Films for Enzyme Immobilization in Biosensors

Abstract

Polymer films deposited on thin film noble metal electrodes on silicon chips, utilizing plasma polymerization are shown to be suited for immobilization of enzymes. Glucose oxidase is covalently coupled via amino- or carboxyl-groups of polymer films made by plasma polymerization of 2-amino-benzotrifluoride, acrylic or methacrylic acid. The concentration of these active surface groups increases by after-treatment in an ammonia- or oxygen-plasma. A biosensor consisting of a thin film metal electrode, plasma polymer film and immobilized glucose oxidase shows an amperometric response to glucose with a fast response time.     

Nitrogen-doped TiO2 from TiN and its visible light photoelectrochemical properties

Homogeneous titanium nitride (TiN) thin film was produced by simple electrophoreic deposition process on Ti substrate in an aqueous suspension of nanosized TiN powder. Nitrogen-doped titanium dioxide (TiO_2−xN_x) was synthesized by oxidative annealing the resulted TiN thin film in air. Photoelectrochemical measurements demonstrated visible light photoresponse for the electrode of annealed electrophoreic deposited TiN samples. It is found that the synthesized TiO_2−xN_x electrode showed higher photo potential under white and visible light illumination than the pure TiO₂ electrode. The photocurrent under visible light illumination was also observed, which increased with the increase of deposition time of TiN thin films.     

Construction and Characterization of Ru(II)Tris(bipyridine)‐Based Silica Thin Film Electrochemiluminescent Sensors

Ru(II) tris‐bipyridine based ECL sensors were produced by embedding the complex inside silica glass thin films deposited via a sol‐gel dipping procedure on K‐glass conducing substrates. Films were prepared starting from a pre‐hydrolyzed ethanolic solution of Si(OC₂H₅)₄ and Ru(bpy)₃Cl₂. Transparent, crack‐free and homogeneous reddish silica layers, having a thickness of 200±20 nm, were obtained. The films, either deposited at room temperature or thermally annealed at 100, 200 and 300 °C for 30 h, were structurally and chemically characterized. Ru(bpy)₃Cl₂ thermal stability was previously checked by thermogravimetric analysis (TGA). The films were investigated by X‐Ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS) and UV‐vis spectroscopy. XPS in‐depth profiles revealed a homogeneous distribution of the ruthenium complex inside the silica thin layers. SIMS data suggested that the embedded Ru(bpy)₃Cl₂ did not react with oxygen inside the oxygen‐rich silica matrix to give Ru‐O bonds. Electrochemical and ECL characterization of the thin film electrodes were made by means of cyclic voltammetry (CV) and controlled potential step experiments. The ECL sensor showed a diffusive redox behavior of the Ru(bpy)₃²⁺/Ru(bpy)₃³⁺ system. Light emission produced from the reaction between oxalic acid and the electrogenerated Ru(bpy)₃³⁺ was larger and stable when thermally treated electrodes were used after a suitable hydration period. The 300 °C treated sample was the best performing sensor both in terms of low complex leakage and sensitivity. Calibration plots relative to oxalic acid were obtained both in stationary and in flowing solutions in the concentration range 2×10^?6?3×10^?4 M. A linear behavior appeared in the former case, while in the latter a slight curvature was evident as a consequence of a finite diffusion time of the analyte inside the thin film. The signal repeatability, obtained by multiple 100 μL of 10^?5 M oxalic acid injections in flowing solutions, was better than 4%. The obtained detection limit (computed as three times the standard deviation of the base‐line noise) was 10^?6 M as oxalic acid.     

Synthesis and characterization of fluorescently labeled core cross‐linked star polymers

A series of fluorescently labeled core cross‐linked star (CCS) polymers were synthesized via the “arm‐first” approach, employing atom transfer radical polymerization (ATRP) to control the resulting architecture. The initiator p‐toluenesulfonyl chloride (TsCl) was used to synthesize “living” poly(methyl methacrylate) (PMMA) macroinitiator, which was subsequently cross‐linked to generate the CCS polymers. Divinylbenzene (DVB) was used as the cross‐linker and 7‐[4‐(trifluoromethyl)coumarin] methacrylamide ( F₁ , λ_ex = 343 nm) was added as a fluorescent labeling monomer. A range of PMMA/DVB/ F₁ based CCS polymers were synthesized with the core domain made selectively fluorescent by using varying amounts of monomer F₁ . The core functionalized stars were characterized using gel permeation chromatography (GPC) equipped with multi‐angle laser light scattering (MALLS), refractive index (RI), and UV–visible detectors. The fluorescence quantum yield (Φ_F) and the amount of fluorescent monomer incorporated into the core were quantified by UV–visible and fluorescence spectrophotometry. It was recognized that the overall molecular weights of the stars produced, along with their core molecular weight, decreased as the mol % of monomer F₁ was increased relative to cross‐linker. Visual confirmation of F₁ incorporation was obtained by fluorescence microscopy of thin polymer films cast on glass substrates. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2422–2432, 2008     

In situ intercalative polymerization of conducting polypyrrole/montmorillonite nanocomposites

Conducting polypyrrole (PPy)‐montmorillonite (MMT) clay nanocomposites have been synthesized by the in situ intercalative polymerization method. The PPy‐MMT nanocomposites are characterized by field‐emission scanning electron microscopy (FE‐SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), ultraviolet–visible (UV–vis) spectroscopy, thermogravimetric analysis (TGA), and Fourier‐transform infrared (FTIR) spectroscopy. XRD patterns show that after polymerization by the in situ intercalative method with ammonium persulfate and 1 M HCl, an increase in the basal spacing from 1.2 to 1.9 nm was observed, signifying that PPy is synthesized between the interlayer spaces of MMT. TEM and SEM micrographs suggest that the coexistence of intercalated MMT layers with the PPy macromolecules. FTIR reveals that there might be possible interfacial interactions present between the MMT clay and PPy matrix. The study also shows that the introduction of MMT clay results in thermal stability improvement of the PPy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2279–2285, 2008     

A new soluble conducting polymer and its electrochromic devices

A new polythiophene derivative was synthesized by both chemical and electrochemical oxidative polymerization of 1‐(1‐phenylethyl)‐2,5‐di(2‐thienyl)‐1H‐pyrrole (PETPy). Of which the chemical method produces a polymer that is completely soluble in organic solvents. The structures of both the monomer and the soluble polymer were elucidated by nuclear magnetic resonance (¹H and ¹³C NMR) and Fourier transform infrared (FTIR) spectroscopy. The average molecular weight has been determined by gel permeation chromatography to be M_n = 3.29 × 10³ for the chemically synthesized polymer. Polymer of PETPy was synthesized via potentiostatic electrochemical polymerization in acetonitrile (AN)/NaClO₄/LiClO₄ (0.1 M) solvent–electrolyte couple. Characterizations of the resulting polymer were performed by cyclic voltammetry, FTIR, scanning electron microscopy, and UV–vis spectroscopy. Four‐probe technique was used to measure the conductivities of the samples. Moreover, the spectroelectrochemical and electrochromic properties of the polymer films were investigated. In addition, dual‐type polymer electrochromic devices based on P(PETPy) with poly(3,4‐ethylenedioxythiophene) were constructed. Spectroelectrochemistry, electrochromic switching, and open circuit stability of the devices were studied. They were found to have good switching times, reasonable contrasts, and optical memories. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2215–2225, 2006     

Deposition of plasma conjugated polynitrile thin films and their optical properties

The plasma polymerization of 4-phenylbenzonitrile was carried out with the objective of synthesizing a novel conjugated polynitrile thin film with a better optical property. The structure, compositions and morphology of the plasma-polymerized 4-phenylbenzonitrile (PPBPCN) thin films were investigated by Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). A fine, homogenous PPBPCN film with a large π-conjugated system and a high retention of the aromatic ring structure of the starting monomer in the deposited plasma films is obtained when a low discharge power of 30 W was used during film formation. For the first time, a blue emission with relatively high photoluminescence intensity for PPBPCN thin films was observed.     

UV‐activated hydrosilylation: a facile approach for synthesis of hyperbranched polycarbosilanes

A facile approach for synthesis of hyperbranched polycarbosilane from AB₂ monomer via UV‐activated hydrosilylation is presented in this communication. The polymerization process was monitored using real‐time FTIR spectroscopy and the resulting hyperbranched polycarbosilanes were characterized using ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR and SEC/MALLS. It is found that hyperbranched polycarbosilane can be synthesized from methyldiallylsilane via UV‐activated hydrosilylation with bis(acetylacetonato)platinum(II) as catalyst. The polymerization activated by UV irradiation was much faster than that under thermal conditions. The similar degree of branching, average number of branch units and the exponent of the Mark–Houwink equation demonstrate that the hyperbranched polycarbosilane synthesized via UV‐activated polyhydrosilylation possesses almost the same branching structure as that synthesized via thermal‐activated polyhydrosilylation. Copyright © 2009 John Wiley & Sons, Ltd.