Synthesis and characterization of polyaniline doped with organic acids

Spectroscopic [UV–visible and Fourier transform IR (FTIR)] and thermal properties of chemically synthesized polyanilines are found to be affected by varying the protonation media (acetic, citric, oxalic, and tartaric acid). The optical spectra show the presence of a greater fraction of fully oxidized insulating pernigraniline phase in polyaniline doped with acetic acid. In contrast, the selectivity in the formation of the conducting phase is higher in oxalic acid as a protonic acid media. The FTIR spectra of these polymers reveal a higher ratio of the relative intensities of the quinoid to benzenoid ring modes in acetic acid doped polyaniline. Scanning electron micrographs revealed a sponge‐like structure derived from the aggregation of the small granules in acetic acid and oxalic acid doped polyaniline. A three‐step decomposition pattern is observed in all the polymers, regardless of the protonic acid used for the doping. The second step loss related to the loss of dopant is found to be higher in the oxalic acid doped polymer. In accordance with these results the conductivity is also found to be higher in oxalic acid doped material. The temperature dependent conductivity measurements show the thermal activated behavior in all the polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2043–2049, 2004     

Enzymatic Synthesis of Semiconductor Polymers by Chloroperoxidase of Caldariomyces fumago

Among intrinsically conducting polymers, polyaniline is traditionally synthesized by chemical or electrochemical methods. Recently enzymatic synthesis of conducting polymers has been explored. In this work, polymers were synthesized using chloroperoxidase from Caldariomyces fumago and substituted anilines such as 2,6-dimethylaniline, 2,6-dichloroaniline, and 2,3,5,6-tetrachloroaniline (TCA), in order to promote a linear polymerization. These polymers were doped with (1S)-(+)-10-camphorsulfonic acid, dodecylbenzenesulfonic acid, and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPSA) with molar ratios of 1:0.25 and 1:0.5. Doped polymers showed conductivity corresponding to the semiconductors. TCA polymer doped with AMPSA showed the higher conductivity values. Different AMPSA concentrations have been tested, and the highest conductivity value of 1.6?×?10^?2?S?m^?1 was obtained for the complex with molar ratio of 1:0.5. This value is similar to those found with other substituted anilines with sulfonic groups. In addition, the enzymatically synthesized polymeric film showed combined transparency and semiconducting properties.     

Studies on phthalocyanine sheet polymers

Cobalt, nickel and copper phthalocyanine sheet polymers are synthesized by heating their respective metal (II) phthalocyanine tetracarboxylic acids at 400 °C in nitrogen atmosphere. These polymers are characterized using UV-Visible spectra, IR spectra, magnetic susceptibility, X-ray powder diffraction and thermogravimetric analysis. Electrical conductivity studies are carried out using two-probe technique in the temperature range 25-200 °C for each polymer. These polymeric materials showed room temperature electrical conductivity 10-1000 times higher values compared to earlier reported values for this type of sheet polymers.     

Facile Synthesis of Supramolecular Ionic Polymers That Combine Unique Rheological,Ionic Conductivity,and Self‐Healing Properties

A new family of supramolecular ionic polymers is synthesized by a simple method using (di‐/tri‐)carboxylic acids and (di‐/tri‐)alkyl amines. These polymers are formed by carboxylate and ammonium molecules that are weakly bonded together by a combination of ionic and hydrogen bonds, becoming solid at room temperature. The supramolecular ionic polymers show a sharp rheological transition from a viscoelastic gel to a viscous liquid between 30 and 80 °C. This sharp viscosity decrease is responsible for an unprecedented jump in ionic conductivity of four orders of magnitude in that temperature range. As a potential application, this chemistry can be used to develop polymeric materials with self‐healing properties, since it combines properties from supramolecular polymers and ionomers into the same material.     

Polyaniline doped by a new class of dopants,benzoic acid and substituted benzoic acid: synthesis and characterization

This work reports on a new class of dopants, benzoic acid and substituted benzoic acids such as 2‐hydroxybenzoic acid, 2‐chlorobenzoic acid, 4‐nitrobenzoic acid, 2‐methoxybenzoic acid, 3‐methylbenzoic acid, 4‐methylbenzoic acid, 3‐aminobenzoic acid and 4‐aminobenzoic acid, for polyaniline. Benzoic acids can be used to dope polyaniline by mixing benzoic acid (or a substituted benzoic acid) with polyaniline in the common solvent 1‐methyl‐2‐pyrrolidone. Properties of benzoic acid doped polyaniline salts are studied using Fourier transform infra‐red, X‐ray diffraction spectroscopy, scanning electron microscopy, thermogravimetric analysis and conductivity measurements. The conductivity of polyaniline‐benzoic acid salt was found to be high (10⁻² S/cm) when compared to polyaniline‐substituted benzoic acid salts (10⁻³–10⁻⁵ S/cm). Copyright © 2005 John Wiley & Sons, Ltd.     

掺杂质子酸的类型对聚苯胺结构和电导率的影响

采用化学氧化聚合法以苯胺为单体，过硫酸铵为氧化剂，在不同质子酸的水溶液中合成聚苯胺，考察质子酸对聚苯胺电性能影响，并通过傅立叶红外吸收光谱（FTIR）和紫外可见光吸收光谱（UV－vis)研究聚苯胺掺杂前后结构的变化。结果表明，龙质子酸掺杂后聚 胺具有导电性是因为其分子链上电荷离城形成了共轭结构，具有不同质子酸中生成的聚苯胺氧化程度不同；分子链共轭程度与掺杂酸对阴离子大小有关，掺杂质子酸对阴离子越大，聚苯胺分子链共轭程度越大，电导率也就越高。     

Synthesis and Properties of Self‐doped Polyaniline with Polycationic Templates via Biocatalysis

The enzyme horseradish peroxidase (HRP) was used to polymerize acid‐functionalized anilines to make self‐doped polymer in the presence of a polycationic template. Anionic templates such as sulfonated polystyrene (SPS) could not function as a suitable template for the polymerization of acid‐functionalized aniline derivatives. Several types of polyelectrolytes were used as templates to observe the structural effects and doping behavior of polyaniline/template complexes. The synthesis is straightforward and the conditions are mild in that the polymerization of conducting polyanilines may be carried out in buffered solutions as high as pH 6, with a stoichiometric amount of hydrogen peroxide and catalytic amount of enzyme. The conductivity of these enzymatically synthesized self‐doped polymers was relatively high without additional doping due to the self‐doping of the acid moieties. The conductivity did not decrease dramatically at pH 3 as is the usual case of unsubstituted HCl‐doped polyaniline and maintained good conductivity even at pH 6. The measured conductivity at pH 4～pH 6 is around 10^?4 S/cm to 10^?6 S/cm.     

Composites of Polystyrene Sulfonic Acid (PSSA)‐Polyaniline and Montmorillonite Clay: Synthesis and Characterization

Polystyrene sulfonic acid (PSSA) doped water‐soluble polyaniline (PANI)/montmorillonite (MMT) clay composites were synthesized by intercalation polymerization in aqueous medium. The properties of the composites were characterized by X‐ray diffraction (XRD), transmission electron microscope (TEM), Fourier‐transform infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X‐ray photoelectron spectroscopy (XPS) and conductivity measurement. The results show that the composite has a mixed nanomorphology and exfoliated silicate nanolayers of MMT clay dispersed in the polyaniline matrix. This composite is more thermal stable than that without clay samples and results in good stable temperature‐dependent dc conductivity [σ_dc(T)] as temperature changed.     

Doping of polyaniline with polymeric dopants in solid state,gel state and solutions

Polystyrene with different degrees of sulfonation was empolyed as a polymeric dopant for polyaniline. The purpose of using a polymeric dopant is to avoid the migration of a small molecule dopant to increase stability of the doped complex. We applied the polymeric dopant to polyaniline in three different ways: in solid state, in solution and in gel state. In solid state, the conducting form was achieved only through a novel thermal doping method with the increase in temperature and pressure. In solution, the doping process was shown to be dependent on the nature of the solution and also on the molecular weight of the polymer. In the gel form of polyaniline, a polymeric dopant with a surprising low degree of sulfonation was found to be successful in the doping process.     

Comparative studies of chemically synthesized polyaniline and poly(o-toluidine) doped with p-toluene sulphonic acid

Polyaniline and poly(o-toluidine) doped with p-toluene sulphonic acid (p-TSA) were synthesized by in situ chemical polymerization method using ammonium per sulphate as an oxidizing agent. This is a novel polymerization process for the direct synthesis of emeraldine salt phase of the polymer. The polymers were characterized by using UV-Vis and FT-IR spectroscopy, SEM, elemental analyzer, TGA/DSC and conductivity measurements. Thermal analysis shows that poly(o-toluidine) is less thermally stable compared to polyaniline. The less conductivity in poly(o-toluidine) is due to the cumulative steric as well as electronic effect of the bulky methyl substituent present on the benzene ring. High temperature conductivity measurements show ‘thermal activated behavior’.     

不同质子酸掺杂对银/聚苯胺纳米复合材料结构和导电性的影响

利用紫外光作为辅助条件,在反胶束体系中采用一步双原位法合成了硝酸(HNO3)、对甲基苯磺酸(TSA)和5-磺基水杨酸(SSA)掺杂的银/聚苯胺(Ag/PANI)纳米复合材料.通过对复合材料进行红外光谱(FTIR)、紫外光谱(UV-Vis)、扫描电镜(SEM)、X射线衍射(XRD)和导电性能的测试,研究了不同质子酸对Ag/PANI纳米复合材料结构、形貌和导电性能的影响.测试结果表明,3种酸掺杂制备的Ag/PANI纳米复合材料均为聚苯胺包覆银粒子的核-壳结构.不同的质子酸掺杂会对Ag/PANI纳米复合材料的电性能有重要影响.在3种酸掺杂的复合材料中,TSA掺杂的复合材料的电导率最佳,为215.14 S·cm-1.     

Electrical and humidity sensing properties of synthesized hydrophosphoric acid doped polyaniline

H₃PO₄ doped polyaniline was synthesized by a single‐step chemical polymerization method using ammonium persulfate as an oxidizing agent. The material characterization was done by SEM, UV–vis spectroscopy and thermogravimetric analysis (TGA). The pellets of the synthesized material were used to study the electrical properties, using a four‐probe method. The room temperature electrical conductivity is found to be 0.2201 S/cm. The electrical resistance in response to the varying humid environment (ranging between 20 and 100% RH) is recorded to evaluate the sensitivity of the H₃PO₄ polyaniline samples toward humidity. The resistance of the samples is found to vary by three orders of magnitude for 20–100% RH and is found to decrease with increasing humidity. The response and recovery time are observed to be 12–14 and 26–30 sec, respectively. Copyright © 2007 John Wiley & Sons, Ltd.     

Investigation of Spectroscopic and Thermal Properties of Poly(o‐toluidine) Doped with Polymeric Acids

Single step polymerization of poly(o‐toluidine) was carried out by using ammonium persulphate as an oxidizing agent. Formation of the conducting emeraldine salt phase of the polymer was confirmed by the UV‐visible and FT‐IR spectroscopic analysis. The elemental composition of the polymer was evaluated by using a CHNS analyzer. Thermal stability of these polymers was investigated by the thermogravimetric analysis. Among the three polymeric acids used for doping purposes, poly(acrylic acid) doped material was found to show less thermal stability compared to poly(styrene sulphonic acid) and poly(vinyl sulphonic acid) doped poly(o‐toluidine).     

Synthesis and characterization of new azobenzenesulfonic acids doped conducting polyaniline

New azobenzene sulfonic acid dopants were synthesized by diazotized coupling reaction of sulphanilic acid diazonium salt with commercially available raw materials such as phenol, m-cresol and 4-phenylphenol. The structures of the dopants are confirmed by NMR and FT-IR. Polyaniline emeraldine base was doped by these new azobenzenesulfonic acid dopants in two different solvent medium such as methanol and N-methylpyrrolidinone to produce green emeraldine salt. The doping process was confirmed by FT-IR and UV-vis spectroscopy. The effect of composition of dopant on the conductivity of the polyaniline was investigated and the results suggest that the conductivity increases with the increase in the dopant concentration and attained maxima for more than 38% in the feed. The conductivity measurements reveal that all the dopants equally effective in producing in high conductivity in the range of 0.02 S/cm and the conductivity of the doped samples are insignificant to the structural difference in the dopant. WXRD and SEM analysis indicate that the doped samples are highly amorphous and porous in nature. The thermal analysis by TGA indicate that all the doped materials were highly stable up to 300 °C for high temperature applications.     

含苯胺低聚物侧链的导电共聚物的合成与性能研究

通过高分子反应合成了含有不同长度苯胺链段的聚甲基丙烯酸类接枝聚合物 ,研究结果发现 ,当苯胺链段达到一定长度时 ,经质子酸掺杂后的聚合物具有一定的电导性 ,其中 ,接枝苯胺八聚体的共聚物经质子酸掺杂后其电导率可以达到 10 - 5S cm .     

Synthesis,characterization, and hoping transport properties of HCl doped conducting biopolymer‐co‐polyaniline zwitterion hybrids

A series of electrically conductive zwitterion hybrid materials were facilely synthesized with anionic acacia gum (AG) and cationic HCl doped polyaniline (PANI) through radical copolymerization method. A representative acacia gum‐polyaniline hybrid (AG‐PANI) was characterized using UV‐vis, FTIR, ¹H NMR, and SEM. HCl doped AG‐PANI possesses zwitterion character due to the presence of NH on PANI and ? COO^? of AG. The cyclic voltammogram of AG‐PANI showed three anodic peaks at 0.20 V, 0.58 V, and 0.64 V along with two cathodic peaks at 0.50 V and 0.40 V with large capacitive background currents. AG‐PANI exhibited electrical conductivity that was found dependent on the ratio of aniline to AG, temperature, and pH. Its electrical conductivity versus temperature plot indicated Mott's nearest‐neighbor hopping mechanism at the temperature range 83–323 K. The hybridization of AG and PANI yielded eco‐friendly advanced functional materials for technological applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Thermal transporting properties of electrically conductive polyaniline films as organic thermoelectric materials

Thermal transporting properties of electrically conductive polyaniline films were first investigated in wide range of temperatures above room temperature as organic thermoelectric materials. Thermal conductivities of various protonic acid-doped polyaniline films were measured by combination of a laser flash method and a differential scanning calorimeter in relation with electrical conductivity and a kind of dopant. The thermal conductivities thus measured are in the range of conventional organic polymers, indicating that the doped polyaniline films have extremely low thermal conductivities among electrically conductive materials, and have correlation with neither electrical conductivity, nor a kind of dopant. Consequently the polyaniline film, which shows very high electrical conductivity, has comparable thermoelectric figure-of-merit (ZT) with feasible inorganic thermoelectric materials such as iron silicide. This revised version was published online in August 2006 with corrections to the Cover Date.     

Preparation and characterization of PVC/PANI conductive composite with extremely low percolation threshold

Aniline was polymerized in the presence of poly(vinyl chloride) (PVC) powders in hydrochloric acid to in situ prepare poly(vinyl chloride)/polyaniline (PVC/PANI) composite particles. UV‐vis spectra and FT‐IR spectra indicate PANI in PVC/PANI composite particles possessed a higher oxidation state with decreased aniline content in reactants. Both conductivity and impact strength of the dodecylbenzenesulfonic acid (DBSA) doped PANI composites (PVC/PANI‐DBSA), which were compression molded from the in situ prepared PVC/PANI particles, increase with the pressing temperature and decrease with the increase of DBSA doped PANI (PANI‐DBSA) loading. An excellent electric conductivity of 5.06 × 10^?2 S/cm and impact strength of 0.518 KJ/m² could be achieved for the in situ synthesized and subsequently compression molded composite. Copyright © 2004 John Wiley & Sons, Ltd.     

Electrical properties of electrochemically doped organic semiconductors using light-emitting electrochemical cells

We present a study of the electrical properties of electrochemically doped conjugated polymers using polymeric light-emitting electrochemical cells (PLECs) and interpreting the results according to a phenomenological model (PM) which assumes that, above the device turn-on voltage, the bulk transport properties of the doped organic semiconductor are responsible for the main contribution to the whole device conductivity. To confirm the predictions of this model, the dependence of the conductivity of PLECs with different parameters is evaluated and compared with the behavior expected for a doped semiconducting polymeric material. The organic semiconductor doping level, the blend concentration of organic semiconducting molecules, the device thickness, the charge carrier mobility, and the temperature are the parameters varied to perform this analysis. We observed that the device conductivity is independent of the active layer thickness, weakly dependent on the temperature, but strongly dependent on the semiconductor doping level, on the semiconductor fraction in the blend, and on the intrinsic charge carrier mobility. These results were well described by the variable range hopping (VRH) model, which has been widely employed to describe the charge transport in doped semiconducting polymeric materials, confirming the prediction of the phenomenological model. The current analysis demonstrates that PLECs are a suitable system for studying, in situ, the electrochemical doping of semiconducting polymers, permitting the evaluation of material properties as, for instance, the density of electronic charge carriers (and, consequently, the ionic charge carrier concentration) necessary to achieve the maximum electrochemical doping level of the organic semiconductor.     

Synthesis,Electrical Conductivity,Spectral and Thermal Stability Studies on Poly(aniline-co-o-nitroaniline)

o-Nitroaniline units were incorporated in the polyaniline backbone through copolymerization with aniline. The copolymers were synthesized for 1:3 and 1:1 molar ratios of aniline and o-nitroaniline in acidic medium using potassium persulphate as oxidant and their properties were compared with that of polyaniline. The polymers showed less electrical conductivity than polyaniline. Unlike polyaniline, the presence of nitro group caused higher frequency dependence of electrical conductivity. Electronic spectra showed a blue shift in both the band of the copolymers due to the decrease in the extent of conjugation leading to lower conductivity, which could also be explained in terms of a decrease of delocalization of electron as evinced from electron para magnetic resonance (EPR) data. Thermo gravimetric analysis (TGA) revealed that copolymer derived from 1:1 molar ratio showed comparable thermal stability with polyaniline and the one derived from 1:3 molar ratios is thermally less stable than polyaniline. Activation energies for thermal degradation were estimated using Broido equation. The temperature dependence of electrical conductivity suggested charge transport is mainly through variable range hopping.