HCN and NH3 (NOx precursors) released under rapid pyrolysis of biomass/coal blends

Rapid pyrolysis of 6 biomass/coal blends (1:4, wt) including rice straw + bituminous (RS + B), rice straw + anthracite (RS + A), chinar leaves + bituminous (CL + B), chinar leaves + anthracite (CL + A), pine sawdust + bituminous (PS + B), and pine sawdust + anthracite (PS + A) was carried out in a high-frequency magnetic field based furnace at 600-1200 °C. The reactor could not only achieve high heating rates of fuel samples but also make biomass and coal particles contact well; secondary reactions of primary products during rapid pyrolysis can also be efficiently reduced. By comparing nitrogen distributions in products of blends (experimental values) with those of the sums of individual biomass and coal (weighted values), nitrogen conversion characteristics under rapid pyrolysis of biomass/coal blends were investigated. Results show that, biomass particles in blends lead to higher experimental char-N yields than the weighted values during rapid pyrolysis of biomass/anthracite blends. The decreased heating rates of both biomass and coal particles caused by the low packing densities of biomass may be the reason. For blends of CL + B in which packing density of chinar leaves is high, and for PS + B during pyrolysis of which melting and shrinkage happen to pine sawdust, both biomass and coal particles can obtain high heating rates, synergies can be found to promote nitrogen release from fuel samples and decrease char-N yields under all the conditions. But the low fluidity and not easily collapsed carbon skeletons of rice straw make the heating rates of rice straw and bituminous particles in RS + B lower than those of CL + B and PS + B, and weaker synergies can be found from char-N yields of RS + B. The synergies can obviously be found to decrease the (NH₃ + HCN)-N yields and make more nitrogen convert to N₂ except for those of several low-temperature conditions (600-700 °C). Under the low-temperature (600-700 °C) condition, synergies make molar ratios of HCN-N/NH₃-N higher than those of the weighted values.     

Thermal Decomposition of Bi(III), Cd(II), Pb(II) and Cu(II) Thiocyanates

Thermal decomposition of Bi(SCN)₃, Cd(SCN)₂, Pb(SCN)₂ and Cu(SCN)₂ has been studied. The thermal analysis curves and the diffraction patterns of the solid intermediate and final products of the pyrolysis are presented. The gaseous products of the decomposition (SO₂ and CO₂) were detected and quantitatively determined. Thermal, X-ray and chemical analyses have been used to establish the nature of the reactions occurring at each stage in the decomposition.This revised version was published online in November 2005 with corrections to the Cover Date.     

Electropolymerization of <Emphasis Type="Italic">trans</Emphasis>-[RuCl<Subscript>2</Subscript>(vpy)<Subscript>4</Subscript>] complex—EQCM and Raman studies

The electropolymerization of trans-[RuCl₂(vpy)₄] (vpy=4-vinylpyridine) on Au or Pt electrodes was studied by cyclic voltammetry, electrochemical quartz crystal microbalance (EQCM) technique, and Raman spectroscopy. Cyclic voltammetry of the monomer at a microelectrode shows the typical Ru(III/II) and Ru(IV/III) waves, together with the vinyl reduction waves at −1.5 and −2.45 V and adsorption wave at −0.8 V. Electrodeposition on EQCM technique performed under potential cycling between −0.9 and −2.0 V revealed that the polymerization proceeded well in advance of the vinyl reduction waves. At potentials more positive than −0.9 V, soluble oligomers were deposited irreversibly on the electrode during the oxidative sweep. The film also showed reversible mass changes due to the oxidation and accompanying ingress of charge-balancing anions and solvent into the film. In contrast, potentiostatic growth of the polymer at −1.6 V was slower because the oligomeric material was lost completely from the electrode. Unreacted vinyl groups were detected by in situ Raman spectroscopy for films grown at −0.7, −0.9, and −1.6 V but were absent when the polymerization was carried out at −2.9 V vs Ag/Ag⁺.     

煤热解过程中含氮气相产物转化规律的实验研究

为了研究煤在热解过程中含氮气相产物的生成规律,在滴管炉反应系统中对四种原煤以及两种脱除矿物质煤样分别在500℃、700℃、900℃和1100℃进行了实验研究。结果表明,随着温度的升高,作为NO前驱物的HCN和NH3的收率随之增加,N2的收率也增加。煤种对含氮气相产物的生成规律也有着较大的影响,煤化程度比较低的煤在热解过程中,燃料氮向气相含氮产物的转化率较高;煤化程度比较高的煤转化率则偏低,大部分的氮缩聚在多环芳香结构中,成为焦炭氮。煤中的矿物质对燃料氮向N2的转化起到了促进作用,而对燃料氮向HCN和NH3的转化起到了抑制作用。     

一个新的双核锌配合物Zn2(dhaash)2(py)4的合成及晶体结构

The crystal of binuclear zinc complex Zn₂(dhaash)₂(py)₄ was obtained in DMF and pyridine, where H₂dhaash is 2,4-dihydroxy-5-acetylacetophenone-N-salicylhydrazone. It has been characterized by IR, UV, element analysis and X-ray single crystal diffraction. The crystallographic data were as follows: monoclinic system, space group P2₁/c, a=1.108 98(11) nm, b=1.640 84(16) nm, c=1.445 14(14) nm, β=108.617(2)°, Z=2, V=2.492 1(4) nm³, D_c=1.466 g·cm^-3, M_r=1 099.74, μ=1.031 mm^-1, F(000)=1 136 and the final R=0.044 8 and wR=0.105 8 for 4 143 observed reflections with I≥2σ(I), respectively. The X-ray crystal structure analysis revealed that, in the centrosymmetric binuclear complex molecule, two zinc(Ⅱ) centers are linked by two oxygen atoms (O(3) and O(3A)), respectively. Zn(1)…Zn(1A) distance is 0.314 81(6) nm, O(3)…O(3A) distance is 0.270 4(2) nm. Every zinc(Ⅱ) ion has an elongated octahedral coordination. For example, the two pyridine nitrogen atoms, one oxygen atom and one nitrogen atom from salicylhydrazone, one oxygen atom from 2,4-dihydroxy-5-acetylacetophenone in one dhaash^2- ligand and one oxygen atom from 2,4-dihydroxy-5-acetylacetophenone in another dhaash^2- ligand coordinated to zinc(Ⅱ) ion, respectively. Two zinc(Ⅱ) ions and all the 72 non-hydrogen atoms in the two dhaash^2- ligands are in the same plane. CCDC: 261929.     

Thermal behaviour of the copper-substituted cobalt hydroxide fluoride series CuxCo1−x(OH)F

The basic salt cobalt(II) hydroxide fluoride was obtained by partial hydrolysis of a 0.2M solution CoF₂. Mixed Co(II)·Cu(II) hydroxide fluorides with an isomorphic substitution of Co(II) by Cu(II) ions up to 20% were also prepared. XRD data obtained on these compounds indicate that they are single-phase compounds, their X-ray powder patterns being almost identical to the Co(OH)_0.7F_1.3 diagram, with Zn(OH)F-type structure. However, their stoichiometries are very close to Co_1?xCu_x(OH)F (0≤x≤0.2). Thermal analysis studies carried out up to 1273 K in still air or under dynamic vacuum conditions show that in air CoO or a mixture of CoO and CuO is formed as final product. In vacuum, at high temperature, with a Ta heating surface, pure α-Co or a mixture of α-Co and Cu is formed at about 973 K.     

New Ceramics Precursors Containing Si and Ge Atoms—Cubic Germasilsesquioxanes—Synthesis,Thermal Decomposition and Spectroscopic Analysis

Compounds of the silsesquioxane type are attractive material precursors. High molecular weights and well-defined structures predestine them to create ceramics with a controlled composition at the molecular level. New molecular precursors of ceramic materials with the ratio of Si:Ge = 7:1 atoms were obtained. The influence of organic substituents on the thermal decomposition processes of germasilsesquioxanes was investigated. Some of the structures obtained are characterized by a high non-volatile residue after the thermal decomposition process. The introduction of the germanium atom to the structure of the silsesquioxane molecular cage reduces the thermal stability of the obtained structures.     

Synthesis of γ-Fe2O3 by Thermal Decomposition of Ferrous Gluconate Dihydrate

Ferrous gluconate dihydrate (FeC₁₂H₂₂O₁₄⋅2H₂O), was prepared and its thermal decomposition was studied by means of simultaneous thermal analysis, supplemented with a two probe d.c. electrical conductivity measurements under the atmospheres of static air, dynamic air and dynamic nitrogen. Under all the atmospheres final product was found to be α-Fe₂O₃ with FeO, γ-Fe₂O₃, Fe₃O₄ etc. as probable intermediates. γ-Fe₂O₃ was formed under the atmosphere of dynamic air containing water vapour. γ-Fe₂O₃ thus synthesised was characterised for its structure, morphology, thermal and magnetic behaviour. This revised version was published online in August 2006 with corrections to the Cover Date.     

Growth of CuInS2 Nanotubes from Cu2S-CuInS2 Heterostructures as a Potential Photovoltaic Material

Chemically synthesized nanostructures possess well-defined domains with an interconnected network, which helps the carriers to bypass the other material in the solar cell while moving to their respective electrodes. In this work, CuInS₂ films constituting CuInS₂ nanotubes and nanoparticles were fabricated using a hot-injection chemical technique, followed by sulfurization. Structural and microstructural investigations reveal Cu₂S nanoparticle formation at an early stage of growth of nanotubes, serving as possible catalyst sites for the subsequent anisotropic growth of the heterostructured hexagons. The crossover takes place over a number of intermediate stages. This sharing of the heterostructure by the hexagonal Cu₂S and chalcopyrite CuInS₂ minimizes the lattice distortion. The Cu₂S- CuInS₂ interface in the heterostructure acts as the nucleation center for CuInS₂ nanotubes. Optical absorption and Raman spectroscopy studies reveal better optical properties for CuInS₂ nanoparticles as compared to CuInS₂ nanotubes. Compared to all other nanostructures, nanowires or nanotubes tend to provide single-crystalline nanograins for direct characterization. These nanoparticles, especially the nanotubes, can be used to form an interconnected network structure of p- and n-type materials in bulk heterojunctions providing the key to improve solar cell efficiencies.     

Zr(WMo)1-x/2VxO8-x/2：多元素同/低价取代立方ZrW2O8结构类型热收缩固溶体的合成、结构与性质

利用酸蒸气水热法合成了Zr(WMo)1-x/2VxO7-x/2(OH)2·2H2O(x=0.04,0.08,0.10,0.14,0.20,0.22,0.26,0.32)四方晶相固溶体。以此为前驱体,通过高温脱水和相转变法合成了立方相Zr(WMo)1-x/2VxO8-x/2(x=0.04,0.08,0.10,0.14,0.20,0.22)固溶体。立方Zr(WMo)1-x/2VxO8-x/2固溶体具有Pa3空间群。Zr(WMo)1-x/2VxO8-x/2的平均晶体结构描述为按照化学计量的ZrV2O7结构与β-ZrWMoO8结构的叠加。ZrV2O7在立方ZrWMoO8中的固溶度为11mol%;立方Zr(WMo)1-x/2VxO8-x/2固溶体的相变温度低于200 K;在200 K～573 K温度范围内具有负热膨胀系数;线热膨胀系数近似为常数。     

新型配合物Mn2Hg4(SCN)12的合成与晶体结构分析

A new inorganic coordination compound Mn₂Hg₄(SCN)₁₂ was synthesized. The grown crystals were characterized by elemental analysis, infrared spectroscopic analysis and powder crystal X-ray diffraction in detail. The crystal structure of Mn₂Hg₄(SCN)₁₂ was determined by single-crystal X-ray diffraction. It belongs to monoclinic system, P2₁/c space group. The cell dimensions are: a=1.171 6 nm, b=1.431 05 nm, c=2.105 1 nm, β=100.738°, and Z=4. In the structure of it, half of Mn²⁺ cations have five-coordinate number, and other half of Mn²⁺ cations have six-coordinate number; 3/4 of Hg²⁺ cations are coordinated by four SCN^-, 1/4 of Hg²⁺ cations are coordinated by three SCN^- and one NCS^-, all the coordination geometry of Hg²⁺ show slightly distorted tetrahedrons. CCDC: 244939.     

Comparative Study on the Decomposition of Chloroform in Thermal and Cold Plasma

Decomposition of trichloromethane (chloroform, CHCl₃) has been studied in inductively coupled RF thermal plasma and in cold plasma, i.e. in silent electric discharge, in neutral and oxidative conditions, as well. GC--MS analysis of the gaseous products and the extracts of the soots were performed and resulted in the formation of solid soot, aliphatic dienes, cyclo-dienes and some aromatic compounds in neutral conditions of RF thermal plasma. In oxidative conditions, however, much less soot and dienes, and much more oxygen-containing products were formed as compared to neutral ones. In the cold plasma reactor, wide range of chlorinated ethane, ethene and propene derivatives were formed in neutral conditions. In oxidative conditions, formation of carbonyl compounds and carbon monoxide as intermediates took place, while the final product consisted of CO₂, H₂O and Cl₂ in the low temperature plasma reactor.     

Synthesis and characterization of metal substituted AlxCr1−x(acetylacetonate)3 single-source precursors for their application to MOCVD of thin films

A detailed study, involving the synthesis of a single-source precursor containing two metal ions sharing the same crystallographic site, has been undertaken to elucidate the use of such a single-source precursor in a CVD process for growing thin films of oxides comprising these two metals, ensuring a uniform composition and distribution of metal ions. The substituted complexes Cr_1−xAl_x(acac)₃, where acac = acetylacetonate, have been prepared by a co-synthesis method, and characterized using UV–Vis spectroscopy, TGA/DTA measurements, and single crystal X-ray diffraction at low temperature. All the studied compositions crystallize in the monoclinic space group P2₁/c with Z = 4 in the unit cell. It was observed that the ratio (Al:Cr) of the site occupancy for the metal ions, obtained from single crystal refinement, is in agreement with the results obtained from complexometric titrations. All the solid state structures have the metal in an octahedral environment forming six-membered chelate rings. M–O acac bond lengths and disorder in the terminal carbon have been studied in detail for these substituted metal–organic complexes. One composition among these was chosen to evaluate their suitability as a single-source precursor in a LPMOCVD process (low-pressure metal–organic chemical vapour deposition) for the deposition of a substituted binary metal oxide thin film. The resulting thin films were characterized by X-ray diffraction, scanning electron microscopy, and infrared spectroscopy.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

Synthesis, crystal structure, spectrum properties, and electronic structure of a novel non-centrosymmetric borate, BiCd3(AlO)3(BO3)4

A novel non-centrosymmetric borate, BiCd₃(AlO)₃(BO₃)₄, has been prepared by solid state reaction methods below 750 °C. Single-crystal XRD analysis showed that it crystallizes in the hexagonal group P6₃ with a=10.3919(15) Å, c=5.7215(11) Å, Z=2. In its structure, AlO₆ octahedra share edges to form 1D chains that are bridged by BO₃ groups through sharing O atoms to form the 3D framework. The 3D framework affords two kinds of channels that are occupied by Bi³⁺/Cd²⁺ atoms only or by Bi³⁺/Cd²⁺ atoms together with BO₃ groups. The IR spectrum further confirmed the presence of BO₃ groups. Second-harmonic-generation measurements displayed a response of about 0.5×KDP (KH₂PO₄). UV-vis diffuse reflectance spectrum showed a band gap of about 3.19 eV. Solid-state fluorescence spectrum exhibited the maximum emission peak at around 390.6 nm. Band structure calculations indicated that it is an indirect semiconductor.     

PROTEINS AND ANIONIC POLYSACCHARIDES AS STABILIZERS OP 0/W EMULSIONS

The possibilities of stabilizing emulsions by means of proteins and polysaccharides have been discussed. It is shown that the use of anionic polysaccharides makes it possible to increase considerably the stability of protein-containing emulsions. The developed methods of stabilizing emulsions by means of anionic polysaccharides are protein-universal and useful for the preparation of emulsions based on phases of different polarity. The use of these methods allows to avoid the use of low-molecular surfactants for the preparation of protein-containing C/W emulsions.     

Thermal reactions of lithiated graphite anode in LiPF6-based electrolyte

The thermal reactions of a lithiated graphite anode with and without 1.3 M lithium hexafluorophosphate (LiPF₆) in a solvent mixture of ethylene carbonate (EC) and ethylmethyl carbonate (EMC) were investigated by means of differential scanning calorimetry (DSC). The products of the thermal decomposition occurring on the lithiated graphite anode were characterized by Fourier transform infrared (FT-IR) analysis. The lithiated graphite anode showed two broad exothermic peaks at 270 and 325 °C, respectively, in the absence of electrolyte. It was demonstrated that the first peak could be assigned to the thermal reactions of PF₅ with various linear alkyl carbonates in the solid electrolyte interphase (SEI) and that the second peak was closely related to the thermal decomposition of the polyvinylidene fluoride (PVdF) binder. In the presence of electrolyte, the lithiated graphite anode showed the onset of an additional exothermic peak at 90 °C associated with the thermal decomposition reactions of the SEI layer with the organic solvents.     

溶胶-凝胶涂附电纺纳米纤维制备ZrO2纳米管

Stable zirconia sol was prepared using inorganic salt(zirconia chloride octahydrate) as the precursor and H₂O₂ as the catalyst. ZrO₂-PBS coaxial nanofibers were fabricated using the sol-gel coating technique to filling poly butylenes succinate(PBS) fibers with zirconium dioxide by electrospun. ZrO₂ nanotubes were obtained via calcining ZrO₂-PBS coaxial nanofibers. The ZrO₂ nanotubes were characterized by TG, SEM and TEM, respectively. The results show that ZrO₂ nanotubes with a diameter of 50～100 nm are obtained after calcining ZrO₂-PBS coaxial nanofibers at 450 ℃.     

纳米CuO的制备及对NH4ClO4热分解的催化性能

研究了快速液相沉淀条件对纳米CuO结构和形貌的影响。并用热分析法考察了不同形貌的纳米CuO对高氯酸铵(AP)分解的催化作用。结果表明,当反应物Cu(NO₃)₂和NaOH的浓度均增大到1.00mol·L^-1或者反应介质乙醇和水的体积比增大到3∶1时,纳米CuO(111)晶面的XRD峰强度弱于其(111)晶面的XRD峰强度;用Na₂CO₃作沉淀剂可获得平均粒径11nm的球形CuO,但团聚严重,添加聚乙二醇(PEG)可改善其分散性。不同形貌的纳米CuO均能强烈催化AP的分解,其中分散性良好的球形纳米CuO,催化活性最强,可使AP的高温分解温度降低99.13℃,分解放热量由590.12J·g^-1增至1380J·g^-1。     

Al掺杂Li-Ni-O系列电池正极材料的制备与性能研究

以Ni(NO₃)₂、Al(NO₃)₃和LiOH为原料，研究了一种制备锂离子电池正极材料LiNi_1-xAl_xO₂(x=0.025～0.30)新的共沉淀方法：在前驱体的制备过程中采用超声波振动，在焙烧前用无水乙醇保护前驱体，并在空气气氛下对前驱体进行焙烧。采用充放电测试、XRD和循环伏安研究了掺铝量、焙烧温度和时间、补锂量以及超声波振动对LiNi_1-xAl_xO₂性能及结构的影响。结果表明，在空气气氛中，正极材料LiNi_1-xAl_xO₂中Al的最佳含量为x=0.2，最佳焙烧温度为700 ℃，焙烧时间为16 h,补锂量为0.05(即：n_Li∶n_Ni+Al=1.05∶1)效果较好；并发现掺铝有利于形成和稳定α-NaFeO₂型层状有序结构。同时发现，超声波振动提高了电池材料的性能。