Preparation of a 2024Al-Based Super-Hydrophobic Surface

A super-hydrophobic 2024Al surface with micro- and nano-scale hierarchical crater-like structure has been prepared by constructing the surface and modifying the textured surface with low energy material of HFTHTMS (HFTHTMS = (heptadecafluoro-1,1,2,2-tetrahydrodecyl)trime thoxysilane). The textured surface was characterized by scan electron microscope (SEM) and x-ray photoelectron spectrum (XPS). The SEM image shows the crater-like surface with micro- and nano-scale hierarchical microstructures. The textured surface modified with HFTHTMS has super-hydrophobicity with a contact angle of 162° and the sliding angle of 3°.     

表面修饰引发的ZnO纳米棒阵列膜的超疏水性

润湿性是固体表面的重要性质之一 ,它受控于固体表面自由能和表面粗糙度的大小 ,一般可用液体在固体表面接触角的大小来衡量 .由于水与超疏水表面 (水与固体表面的接触角大于 1 5 0°的表面 )的接触面积很小 ,通过水所发生的化学发应和化学键的形成受到限制 ,使这种表面具有防水、防污染和防氧化等多种功能 ,因而备受人们的关注 [1～ 6 ] .作为宽禁带半导体材料 ,Zn O以其独特的光电和催化等性质在短波激光器、气体传感器、高效催化剂、太阳能电池等方面具有广阔的应用前景 .表面润湿性的研究对于将 Zn O用于各种器件非常重要 .Pesika等 […     

蚊子体表面的微纳米结构与浸润性

通过光学显微镜及自行设计的接触角测试系统研究了成蚊体表面(如翅膀、 复眼)的浸润行为, 发现了不同的体表面由于不同的生物功能而具有不同的超疏水特性. 通过扫描电子显微镜检测成蚊翅膀和复眼表面, 揭示了分布在成蚊体表面上的不同的微观结构形貌, 另外, 微米结构表面上还包含了纳米结构是其体表面微观结构的共同属性. 因此, 微纳米等级结构与浸润性之间存在重要的依赖关系.     

超疏水性表面在冷凝条件下的润湿特性

采用测量接触角和观测偏光显微镜对超疏水表面在冷凝条件下的疏水特性进行了研究, 发现冷凝蒸汽进入超疏水表面的微凸起内冷凝, 表面的疏水特性被破坏, 表面的润湿特性变得不均匀, 部分区域甚至呈现亲水状态. 根据实验结果提出了冷凝条件下粗糙表面表观接触角的计算模型, 并使用冷凝条件下表面接触角的测量结果进行了验证.     

Characterization and Wettability of ZnO Film Prepared by Chemical Etching Method

ZnO thin films were prepared by a chemical etching method and their wettability was investigated. The structure and surface composition structure were characterized by means of scanning electron microscopy, X-ray photoelectronic spectrometry(XPS), X-ray diffraction(XRD) and Raman spectrometry. These analyses reveal that the etched films were large-scale micro-nanohierarchical structures composed of a Zn core and a ZnO coating. Superhydrophobic surfaces with water contact angles of over 150o were obtained by n-octadecanethiol(ODT) modification. The XPS and Raman results indicate that ODT molecules were bound to the ZnO surface with the S head group by forming Zn-S bond.     

具有平整表面的定向纳米碳管膜的制备

为了获得表面平整的定向纳米碳管，通过化学及物理的方法将纳米碳管膜进行反转，使其原来的AAO模板底面成为新的表面，用溶液逐步去除表面的铝和氧化铝后，获得了平整的定向纳米碳管膜表面，从而可将其作为工作面使用. 还比较了5％NaOH和6%H₃PO₄＋1.8%H₂CrO₄溶液去除氧化铝的效果.     

含氟丙烯酸酯共聚物制备超疏水表面及其形成机理的研究

以丙烯酸全氟烷基乙基酯和甲基丙烯酸甲酯为共聚单体, 分别以用微乳液聚合法和溶液聚合法制备的无规共聚物和用可逆加成-断裂链转移制备的嵌段共聚物作为成膜共聚物, 并以1,1,2-三氟三氯乙烷作为溶剂, 采用溶剂挥发成膜法可以直接制备出超疏水膜, 聚合物膜对水的接触角可达160°. 改变聚合物结构和成膜条件, 探讨了该类超疏水膜的形成机理和影响因素. 发现膜的表面形貌和疏水性与共聚物的组成、结构、分子量以及成膜条件密切相关, 随着共聚物中氟含量的增大, 膜的表面形貌都趋于平滑; 而且, 无规共聚物比嵌段共聚物更易形成粗糙度好的膜; 同时, 较大的聚合物分子量和适宜的高的成膜温度都对形成粗糙结构有利.     

微结构与表面修饰对二氧化硅多孔薄膜疏水性能的影响

通过引入聚乙二醇(PEG)改性传统二氧化硅(SiO2)溶胶,得到了粒径分布较宽且粒径可控的溶胶。比较了六甲基二硅氮烷(HMDS)溶胶内修饰和薄膜表面修饰以及溶胶粒径对SiO2薄膜疏水性能的影响。采用动态光散射粒度仪定量测试了二氧化硅溶胶老化过程中粒度的变化,用原子力显微镜、接触角测试仪、红外光谱仪、紫外-可见-近红外分光光度计分别对薄膜的表面形貌、表观静态接触角、薄膜成分及透光率等进行了测量。结果表明:PEG的添加可有效增大溶胶粒度从而增大薄膜的粗糙度,提高薄膜的疏水性。表面修饰效果受修饰方式和SiO2粒径影响,粒径较小时有利于溶胶内修饰,粒径较大时有利于对薄膜修饰。经过表面修饰剂(HMDS)的气氛处理得到了接触角为152°的超疏水薄膜,而且相比溶胶内修饰可以减小薄膜透光率的损失。     

Investigation of transfer film of PTFE/bronze composites on 2024Al surface

Polytetrafluoroethylene (PTFE) composites filled with 10–30% volume content of bronze powder were prepared through molding and sintering process. Transfer films of these composites were prepared on surface of 2024 Al bar through friction method under certain condition. Roughness, morphology, andelement of these transfer films were investigated using scanning electron microscope (SEM) and energy dispersive spectrometer (EDS) methods. Tribological propertiesof these transfer films sliding against GCr15 steel ball were tested using a DFPM reciprocating tribometer. Worn surfaces were observed and analyzed using SEM and EDS methods. It was found that uniformity and continuity of the transfer films were obviously improved by the increase of bronze content of the composites. Transfer films with better uniformity and continuity holds longer wear life. Considerably lower friction coefficient and longer wear life of these transfer films indicate that the transfer films prepared in the experiment could effectively prevent direct contact of metal friction pair and thus protect them from heavy wear. SEM and EDS analyses of the worn surfaces indicate that adhesion wear and fatigue wear were main wear modes of the transfer film. Copyright © 2009 John Wiley & Sons, Ltd.     

铝片表面阳极氧化铝膜的光催化作用

采用阳极电化学氧化在铝片表面制备出表面含有氧化铝膜的铝片(AAO/Al), 分别用FTIR-ATR技术和密闭间歇式反应装置考察了该样片对油酸和乙烯的光解作用, 结合UV-DRS和FTIR表征结果对薄膜在油酸和乙烯光解中的作用进行了探讨. 结果表明：AAO/Al能够吸收小于265 nm的紫外光, 而无AAO膜的铝片对波长大于220 nm的紫外光没有任何吸收；254 nm紫外光照射下AAO/Al对油酸和乙烯的光解具有明显的促进作用, 光照3 h油酸的分解率达到70%, 乙烯也有9%的分解, 但相同条件下在无AAO膜的铝片上, 油酸的光解率仅为30%, 乙烯几乎不分解；然而, 在365 nm紫外光照射下, AAO/Al同纯铝片一样对两反应物的光解都没有任何促进作用. 分析认为, AAO膜能吸收254 nm的紫外光和对有机物分解具有光催化作用的可能原因是在AAO膜结构中存在过量的Al原子和氧空位.     

分子自组装法制备具有可控浸润性的铜表面简

通过简单浸泡的方法在铜基底上制备出了具有微纳米复合结构的氧化铜,再利用混合硫醇溶液[含HS(CH2)9CH3和 HS(CH2)11OH]对浸泡后的表面进行修饰,通过控制溶液中HS(CH2)11OH的浓度,制备出一系列具有不同浸润性的铜表面,实现表面从超疏水到超亲水的有效调控. 研究发现,表面浸润的可控性源于表面复合结构与不同化学组成的协同作用,微纳米复合结构的存在为表面浸润性的调节提供了必要的条件.     

获得高性能电致变色薄膜的ITO表面修饰方法

氧化铟锡玻璃(ITO)以其优良的导电性能和透过率以及相对低的反应活性使其在显示器和电致变色器件中有广泛的应用. 然而, ITO表面的金属氧化物基团也带来了一些问题, 如通过物理方法沉积的电致变色薄膜易从ITO基底上脱离, 从而降低器件寿命, 此种问题在使用液体电解质时显得尤为突出. 为此, 我们利用有机酸小分子对ITO基底表面进行修饰, 继而利用电化学沉积的方法制备聚3,4-(2,2-二甲基丙烯二氧基)噻吩电致变色薄膜. XPS结果表明基底与修饰物间以化学键结合, 超声波处理可以看出电致变色薄膜在修饰后的基底上有更好的稳定性. 本研究提供了一种简单易行的方法来获得高性能的高分子电致变色薄膜.     

Preparation of Polycarbonate-ZnO Nanocomposite Films: Surface Investigation after UV Irradiation

Polycarbonate (PC)-ZnO films with different percentages of ZnO were prepared by a solution stirring technique and subjected to ultraviolet (UV; λ = 254 nm) irradiation. Structural parameters of the samples and the effects of UV irradiation on the surface properties of the PC and PC-ZnO nanocomposites were evaluated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), water contact angle (WCA) measurements, and a Vickers microhardness (H_V) tester. The XRD patterns of the nanocomposite films were found to show an increase in crystallinity with the increasing ZnO nanoparticles percentage. The WCA was found to be reduced from 90° to 17° after 15 h of UV irradiation, which could be ascribed to the oxidation of the surface of the samples during the irradiation and exposure of the ZnO nanoparticles, a result that is also supported by the obtained XPS data. The microhardness value of the PC-ZnO films including 30 wt.% ZnO enhanced considerably after UV radiation, which can also be attributed to the exposition of the ZnO nanoparticles after photodegradation of the PC superficial layer of the nanocomposite films.     

分子自组装法制备具有可控浸润性的铜表面

通过简单浸泡的方法在铜基底上制备出了具有微纳米复合结构的氧化铜, 再利用混合硫醇溶液[含HS(CH₂)₉CH₃和 HS(CH₂)₁₁OH]对浸泡后的表面进行修饰, 通过控制溶液中HS(CH₂)₁₁OH的浓度, 制备出一系列具有不同浸润性的铜表面, 实现表面从超疏水到超亲水的有效调控. 研究发现, 表面浸润的可控性源于表面复合结构与不同化学组成的协同作用, 微纳米复合结构的存在为表面浸润性的调节提供了必要的条件.     

静电组装金纳米粒子制备局域表面等离子体共振传感膜

采用聚电解质自组装技术制备局域表面等离子体共振(LSPR)传感膜的方法, 在玻璃基片上依次沉积聚电解质PDDA, PSS和PVTC, 并通过静电吸附构建胶体金纳米粒子自组装膜形成LSPR传感膜. 利用扫描电镜对LSPR传感膜表面形貌以及膜中金纳米粒子的粒径进行了表征, 同时通过紫外-可见消光光谱对其灵敏度和渗透深度等重要参数进行检测. 研究结果表明, 所制备的LSPR传感膜粒子分布均匀、单分散性好、稳定性高、重现性好; 消光峰位对样品溶液折射率的检测灵敏度为71 nm/RIU, 相应的峰强检测灵敏度为0.21 AU/RIU, 对表面吸附层的渗透深度约为16 nm.     

薄膜表面的分形特征

在计算机上用随机数相加的方法产生了一个分形表面,对这个表面的模拟测量表明,z方向分辨率变化对分形维数测量结果影响很小,x、y方向分辨率降低时会导致测量结果统计误差增大用扫描隧道显微镜（STM）测量了沉积在三种不同基底上的Au膜的分形维数．测得Au／陶瓷的分形维数D＝2.15,Au／光学玻璃的分形维数D＝2.06．Au／载玻片上各点的分形维数较不一致．同时讨论了多图方法中各单图曲线之间不衔接的原因．     

油分散性氧化锌纳米微粒的制备及表征

采用直接沉淀法制备了异丁酸修饰纳米氧化锌微粒，用XRD、TEM、XPS、IR、UV-Vis、PL等检测手段对样品进行结构表征。结果表明：所制的样品为纤锌矿结构的氧化锌颗粒，粒度约为20 nm，异丁酸分子与表面锌原子以双齿螯合的形式结合。 Zn(II)2p_3/2的结合能与Zn的标准峰位相比，向低结合能方向移动了1.5 eV，其在可见光区比紫外区的荧光发射显著增强。分散性实验表明，样品在有机溶剂中有良好的分散性。     

Modulation of Hydrophobic Interaction by Mediating Surface Nanoscale Structure and Chemistry,not Monotonically by Hydrophobicity

The hydrophobic (HB) interaction plays a critical role in many colloidal and interfacial phenomena, biophysical and industrial processes. Surface hydrophobicity, characterized by the water contact angle, is generally considered the most dominant parameter determining the HB interaction. Herein, we quantified the HB interactions between air bubbles and a series of hydrophobic surfaces with different nanoscale structures and surface chemistry in aqueous media using a bubble probe atomic force microscopy (AFM). Surprisingly, it is discovered that surfaces of similar hydrophobicity can show different ranges of HB interactions, while surfaces of different hydrophobicity can have similar ranges of HB interaction. The increased heterogeneity of the surface nanoscale structure and chemistry can effectively decrease the decay length of HB interaction from 1.60 nm to 0.35 nm. Our work provides insights into the physical mechanism of HB interaction.     

纳米氧化锌的合成及表面改性

以硫酸锌、尿素为原料,采用均相沉淀法合成了纳米氧化锌.研究了硬脂酸对所制的纳米氧化锌粉体表面改性的机理及其对粉体亲油性的影响.实验结果表明,硬脂酸中的羧基与纳米氧化锌粉体颗粒表面的羟基发生了酯化反应,并在表面形成单分子膜.经过表面改性的纳米氧化锌由亲水性转化为亲油性.同时,就纳米氧化锌粉体硬脂酸表面改性反应,探讨了反应摩尔分数、反应温度和反应时间对产物的影响,从而筛选出粉体亲油性最大的反应条件为:硬脂酸质量分数为7%;反应温度为50℃;反应时间为1h.     

铝表面ZnO/Zn-Al LDH微米-纳米结构及其超级疏水性能

A multi-dimension bionic-like super-hydrophobic material， ZnO/Zn-Al LDH， was fabricated by modifying the Al surface in alkaline conditions at room temperature. After coated by ZnO/Zn-Al LDH， the aluminum surface shows both micro- and nano-bionic-like structures of lotus leaves.