Comparative Adsorption of Lead(II) on Flake and Bead‐Types of Chitosan

The adsorption of Pb(II) ions from aqueous solutions by chitosan flakes and beads was studied. The chitosan beads were prepared by casting an acidic chitosan solution into alkaline solution. Experiments were carried out as a function of pH, agitation period and initial concentration of Pb²⁺ ions. The uptake of Pb²⁺ ions from aqueous solution was determined from changes in concentration as measured by atomic absorption spectroscopy. The maximum uptake of Pb²⁺ ions on chitosan beads was greater than that on chitosan flakes. Adsorption isothermal data could be interpreted by the Langmuir equation. The experimental data of the adsorption equilibrium from Pb²⁺ ion solutions correlated well with the Langmuir isotherm equation. SEM analyses were also conducted for visual examination of the chitosan flakes and beads. Physical properties including surface area and average pore diameter were characterized by N₂ adsorption experiment.     

Kinetics and equilibrium adsorption of Cu(II), Cd(II), and Ni(II) ions by chitosan functionalized with 2[-bis-(pyridylmethyl)aminomethyl]-4-methyl-6-formylphenol

Chitosan biopolymer chemically modified with the complexation agent 2[-bis-(pyridylmethyl)aminomethyl]-4-methyl-6-formylphenol (BPMAMF) was employed to study the kinetics and the equilibrium adsorption of Cu(II), Cd(II), and Ni(II) metal ions as functions of the pH solution. The maximum adsorption of Cu(II) was found at pH 6.0, while the Cd(II) and Ni(II) maximum adsorption occurred in acidic media, at pH 2.0 and 3.0, respectively. The kinetics was evaluated utilizing the pseudo-first-order and pseudo-second-order equation models and the equilibrium data were analyzed by Langmuir and Freundlich isotherms models. The adsorption kinetics follows the mechanism of the pseudo-second-order equation for all studied systems and this mechanism suggests that the adsorption rate of metal ions by CHS-BPMAMF depends on the number of ions on the adsorbent surface, as well as on their number at equilibrium. The best interpretation for the equilibrium data was given by the Langmuir isotherm and the maximum adsorption capacities were 109 mg g-1 for Cu(II), 38.5 mg g-1 for Cd(II), and 9.6 mg g-1 for Ni(II). The obtained results show that chitosan modified with BPMAMF ligand presented higher adsorption capacity for Cu(II) in all studied pH ranges.     

Adsorption of chromium from aqueous solution using chitosan beads

A basic investigation on the removal of Cr(III) and Cr(VI) ions from aqueous solution by chitosan beads was conducted in a batch adsorption system. The chitosan beads were prepared by casting an acidic chitosan solution into an alkaline solution. The influence of different experimental parameters; pH, agitation period and different concentration of Cr(III) and Cr(VI) ions was evaluated. A pH 5.0 was found to be an optimum pH for Cr(III) adsorption, and meanwhile pH 3.0 was the optimum pH for the adsorption of Cr(VI) onto chitosan beads. The Langmuir and Freundlich adsorption isotherm models were applied to describe the isotherms and isotherm constants for the adsorption of Cr(III) and Cr(VI) onto chitosan beads. Results indicated that Cr(III) and Cr(VI) uptake could be described by the Langmuir adsorption model. The maximum adsorption capacities of Cr(III) and Cr(VI) ions onto chitosan beads were 30.03 and 76.92 mg g⁻¹, respectively. Results showed that chitosan beads are favourable adsorbents. The Cr(III) and Cr(VI) ions can be removed from the chitosan beads by treatment with an aqueous EDTA solution.     

Crosslinked chitosan nanofiber mats fabricated by one-step electrospinning and ion-imprinting methods for metal ions adsorption

The Pb(Ⅱ)ion-imprinting electrospun crosslinked chitosan nanofiber mats were fabricated by one-step electrospinning and ion-imprinting methods and their application as adsorbents for metal ions was also investigated.The resulting chitosan nanofiber mats were characterized by scanning electron microscopy(SEM),Fourier transform infrared spectroscopy(FTIR),X-ray photoelectron spectroscopy(XPS)and thermal gravimetric analysis(TGA).The Pb(Ⅱ)ion-imprinting electrospun crosslinked chitosan nanofiber mats were used as adsorbents for the removal of Pb(Ⅱ)ions from aqueous or acid solutions.The effects of p H values,contact time,content of crosslinker(glutaraldehyde)on Pb(Ⅱ)ions adsorption were studied.The results indicated that the Pb(Ⅱ)ion-imprinting electrospun crosslinked chitosan nanofiber mats had the highest adsorption capacity of 110.0 mg/g at p H 7.The kinetic study demonstrated that the adsorption of Pb(Ⅱ)ions followed the pseudo-second-order model.The equilibrium isotherm data showed that the Langmuir model was the most suitable for predicting the adsorption isotherm of the studied system.The Pb(Ⅱ)ion-imprinting electrospun crosslinked chitosan nanofiber mats had good adsorption selectivity,which illustrates the equilibrium adsorption capacity in the order of Pb(Ⅱ)Cu(Ⅱ)Zn(Ⅱ)Cd(Ⅱ)Ni(Ⅱ).The Pb(Ⅱ)ion-imprinting electrospun crosslinked chitosan nanofiber mats were stable and had good reuse ability.     

Preparation and adsorption properties of monodisperse chitosan-bound Fe3O4 magnetic nanoparticles for removal of Cu(II) ions

Monodisperse chitosan-bound Fe(3)O(4) nanoparticles were developed as a novel magnetic nano-adsorbent for the removal of heavy metal ions. Chitosan was first carboxymethylated and then covalently bound on the surface of Fe(3)O(4) nanoparticles via carbodiimide activation. Transmission electron microscopy micrographs showed that the chitosan-bound Fe(3)O(4) nanoparticles were monodisperse and had a mean diameter of 13.5 nm. X-ray diffraction patterns indicated that the magnetic nanoparticles were pure Fe(3)O(4) with a spinel structure, and the binding of chitosan did not result in a phase change. The binding of chitosan was also demonstrated by the measurement of zeta potential, and the weight percentage of chitosan bound to Fe(3)O(4) nanoparticles was estimated to be about 4.92 wt%. The chitosan-bound Fe(3)O(4) nanoparticles were shown to be quite efficient for the removal of Cu(II) ions at pH>2. In particular, the adsorption rate was so fast that the equilibrium was achieved within 1 min due to the absence of internal diffusion resistance. The adsorption data obeyed the Langmuir equation with a maximum adsorption capacity of 21.5 mg g(-1) and a Langmuir adsorption equilibrium constant of 0.0165 L mg(-1). The pH and temperature effects revealed that the adsorption capacity increased significantly with increasing pH at pH 2-5, and the adsorption process was exothermic in nature with an enthalpy change of -6.14 kJ mol(-1) at 300-330 K.     

Synthesis and characterization of silica gel microspheres encapsulated by salicyclic acid functionalized polystyrene and its adsorption of transition metal ions from aqueous solutions

The present study was undertaken to develop a novel adsorbent for heavy metal ions, and this paper presents the synthesis and characterization of a composite material-silica gel microspheres encapsulated by salicyclic acid functionalized polystyrene (SG-PS-azo-SA) with a core-shell structure. SG-PS-azo-SA was used to investigate the adsorption of Mn(II), Co(II), Ni(II), Fe(III), Hg(II), Zn(II), Cd(II), Cr(VI), Pd(II), Cu(II), Ag(I), and Au(III) from aqueous solutions. The results revealed that SG-PS-azo-SA has better adsorption capacity for Cu(II), Ag(I) and Au(III). Langmuir and Freundlich isotherm models were applied to analyze the experimental data, the best interpretation for the experimental data was given by the Langmuir isotherm equation with the maximum adsorption capacity for Cu(II), Ag(I), and Au(III) at 1.288 mmol g⁻¹, 1.850 mmol g⁻¹ and 1.613 mmol g^t-1, respectively. Thus, silica gel encapsulated by salicyclic acid functionalized polystyrene (SG-PS-azo-SA) is favorable and useful for the removal of Cu(II), Ag(I) and Au(III) metal ions.     

交联羧甲基魔芋葡甘聚糖吸附重金属离子的研究

以异丙醇为分散剂,环氧氯丙烷为交联剂,在碱性介质中由一氯乙酸和魔芋葡甘聚糖(KGM)反应,制备了取代度为0.265和0.550的两种交联羧甲基魔芋葡甘聚糖(CMKGM),并将其用于吸附溶液中Cu2 、Pb2 和Cd2 。结果表明,CMKGM对3种重金属离子的吸附约在20min内达到平衡,与金属离子类型无关,吸附遵从二级动力学方程;pH对吸附量影响较大,适宜范围为5~6;吸附能较好地服从Langmuir等温吸附方程,CMKGM(DS=0.550)吸附Pb2 的最大吸附容量(Qm)为41.7mg/g,Langmuir常数(b)为0.305mg/L,均大于Cu2 和Cd2 相应值;再生后的CMKGM吸附性能好,脱吸附百分率高。     

Adsorption behavior of Fe(II) and Fe(III) ions on thiourea cross-linked chitosan with Fe(III) as template

A new type of thiourea cross-linked chitosan with Fe(III) as template (TCCTS template) was synthesized. The adsorption of Fe(II) and Fe(III) on this TCCTS template was studied. The factors affecting adsorption such as pH and contact time were considered. The results showed that the optimum pH value for adsorption was pH = 5.0 and the adsorption equilibrium time was about 60 min. The adsorption isotherms and kinetics were investigated, and the equilibrium data agreed very well with the Langmuir model and the pseudo second-order model could describe adsorption process better than the pseudo first-order model. Results also showed that TCCTS template was a favourable adsorbent for Fe(II) and Fe(III) in aqueous solution.     

表面印迹纳米磁性壳聚糖的制备及对Cu(Ⅱ)的吸附研究

将壳聚糖与自制的纳米四氧化三铁反应,加入一定量的铜盐使其与壳聚糖络合,再用环氧氯丙烷交联,用酸洗脱铜离子,得到表面印迹的纳米磁性壳聚糖.考察了阴离子、交联剂浓度对铜印迹效果的影响.用振动磁力仪及透射电镜对样品的性质进行表征.研究了表面印迹的纳米磁性壳聚糖对Cu2 的吸附性能.研究结果显示,用硝酸铜印迹制备的表面印迹纳米磁性壳聚糖吸附剂平均粒径为25nm,饱和磁化强度为98.56emu/g,壳聚糖含量为18.7%.吸附剂吸附容量大,吸附速度快.在Cu2 初始浓度为3.91mmol/L,pH为5时,15min即达到吸附平衡,以壳聚糖计Cu2 的饱和吸附量为4.07mmol/g,比纯壳聚糖粉高2倍.在含Zn2 或Cd2 、Pb2 的二元体系溶液中,离子印迹吸附剂对Cu2 具有明显的选择吸附性,而未印迹的纯壳聚糖粉几乎没有选择性.吸附剂易回收,重复使用性好,重复使用4次后,吸附量约保留最初饱和吸附量的98%.     

Copper (II) adsorption from aqueous solution by herbaceous peat

In this research, the herbaceous peat collected from Gavurgolu peatlands, one of the biggest Turkish peatlands, was utilized as an adsorbent for the removal of copper (II) ions from aqueous solution. Adsorption experiments were conducted under various conditions, i.e., initial concentration, temperature, and pH. While the amount of Cu (II) adsorbed on the peat increased with increasing concentration of Cu (II) ions, it was not markedly affected by temperature and pH. Percentage removal was higher at lower concentration. For example, the maximum percentage removal of Cu (II) ions for initial concentration of 3 x 10(-4) M was 97.04% at 21 degrees C and pH 5.5. The adsorption capacity (Q(0)) of the peat was 4.84 mgg(-1) from Langmuir adsorption isotherm for the concentration range of 3 x 10(-4)-6 x 10(-4) M at 21 degrees C and pH 5.5. The equilibrium time of adsorption of Cu (II) ions was 150 min and independent of concentration and temperature. The amount of Cu (II) adsorbed at equilibrium time did not considerably change with temperature and pH. It was also determined that adsorption isotherm followed both Freundlich and Langmuir. Uptake mechanism of Cu (II) ions by the peat occurs via cation exchange (especially by means of Ca(2+) and Mg(2+)) as well as copper/peat complexation. Adsorption kinetic was consistent with the pseudo-second-order model.     

氨基葡聚糖对水溶液中铜离子的吸附与脱附

自虾、蟹壳等水产加工废料中提取的甲壳质,经脱乙酰基反应,可得氨基葡聚糖,单体结构可表示为左图。该碱性多糖无毒,不溶于水及碱性溶液,在pH～4.5的稀酸中会溶涨,酸性更强时可溶解并成盐。若要求该聚合物以稳定的固态存在于水中,介质的酸性只允许在很小的范围内变化。聚糖中的氨基与过渡金属离子有良好的螯合作用,可作为固体吸附剂吸附水中微量的有害重金属离子。据文献报导,这类吸附大多呈Langmuir型,但Pb(Ⅱ)与Cr(Ⅲ)是例外,它们的吸附等温线表现出单层吸附饱和后,又呈现多层吸附的特征。扫描电镜的照片表明聚糖吸附Pb(Ⅱ)、Cr(Ⅲ)后,表面有瘤状小结节生成。溶液pH升高有利于重     

A NOVEL METAL CHELATE AFFINITY ADSORBENT FOR PROTEIN UPTAKE

In this article,a spherical chitosan gel crosslinked by epichlorohydrin was prepared.It was then loaded with copper ions to produce a metal chelate affinity adsorbent for protein.The uptake of bovine serum albumin(BSA)by the affinity adsorbent was investigated.and the adsorption capacity for BSA as high as 40mg/g-wet beads was observed.The adsorption equilibrium data was well correlated by the Langmuir equation.The adsorption was considerably affected by pH.In additio.The amount of BSA adsorbed onto the beads decreased with the increasing of aqueous phase ionic strength,so adsorbed BAS can be desorbed by adjusting pH orionic strength of the solution.     

A NOVEL METAL CHELATE AFFINITY ADSORBENT FOR PROTEIN UPTAKE

1. INTRODUCTION Chitosan is a hydrolyzed derivative of chitin and belongs to a family of linear unbranched polysaccharides which contain large amounts of 1,4-linked-2-amino-2-deoxy-β-D-glucan residues. The presence of free amine groups in chitosan enhances the solubility and reactivity of this polymer. Interest in modifying chitosan by using glutaraldehyde has recently increased. The derivatized polymers have been employed for many applications [1~2], including protein immobilization…     

Investigation of Metal Ion Removal Selectivity Properties of the Modified Polyacrylamide Hydrogels Prepared by Transamidation and Hofmann Reactions

Modified crosslinked polyacrylamides having different functional groups prepared by transamidation reaction in aqueous and non‐aqueous medium and by Hofmann reaction were used as chelating agents for removal of Cu(II), Cd(II) and Pb(II) ions from aqueous solutions at different pH values. Under non‐competitive conditions, polymers adsorbed different amounts of metal ions, depending on their functional groups and swelling abilities. The metal ion adsorption capacities of polymers changed between 0.11–1.71 mmol/g polymer. Under competitive conditions, while the polymers having mainly secondary amine groups were highly selective for Cu(II) ions (99.4%), those having mainly secondary amide and carboxylate groups have shown high selectivity towards Pb(II) ions (99.5%). The selectivity towards Cu(II) ion decreased and Pb(II) ion selectivity increased by the decrease of the pH of the solutions. The high initial adsorption rate (<10 min) suggests that the adsorption occurs mainly on the polymer surface. A regeneration procedure by treatment with dilute HCl solution showed that the modified polymers could be used several times without loss of their adsorption capacities.     

Adsorption of some bivalent heavy metal ions from aqueous solutions by manganese nodule leached residues

The leached residue, generated after selective extraction of Cu, Ni, and Co in sulfur dioxide-ammonia leaching of manganese nodules, was characterized and batch isothermal adsorption experiments were conducted at ambient temperature to evaluate the effectiveness of the water-washed leached residue for removal of different bivalent metal ions from aqueous synthetic solutions. The effects of pH, initial metal ion concentrations, amount of adsorbent, interfering ions, and heat treatment were also investigated. The uptake of metal ions increased with increasing pH. Under identical conditions the adsorption capacity increased in the order Cd(2+)相似文献   

Adsorption of Cu(II) from aqueous phase by Cedar bark

The capability of Cedar bark (Cedrus atlantica Manetti) (CB) for the adsorption of Cu(II) from aqueous solutions was examined. Adsorption isotherm and kinetics of Cu(II) by CB were investigated through a number of batch adsorption experiments. The effect of experimental parameters such as initial Cu(II) concentration, adsorbent mass, initial pH and ionic strength on the removal of metal ions was examined. Equilibrium data were fitted to the Langmuir, Freundlich and Harkins–Jura isotherm models. Experimental equilibrium data were best represented by the Langmuir and Harkins–Jura isotherms. The findings revealed that the CB has the potential to be used as an adsorbent for the removal of heavy-metal ions from aqueous solutions.     

Biosorption of nickel(II) and copper(II) ions from aqueous solution by Streptomyces coelicolor A3(2)

The biosorption of nickel(II) and copper(II) ions from aqueous solution by dried Streptomyces coelicolor A3(2) was studied as a function of concentration, pH and temperature. The optimum pH range for nickel and copper uptake was 8.0 and 5.0, respectively. At the optimal conditions, metal ion uptake was increased as the initial metal ion concentration increased up to 250 mg l(-1). At 250 mg l(-1) copper(II) ion uptake was 21.8% whereas nickel(II) ion uptake was found to be as high as 7.3% compared to those reported earlier in the literature. Metal ion uptake experiments were carried out at different temperatures where the best ion uptake was found to be at 25 degrees C. The characteristics of the adsorption process were investigated using Scatchard analysis at 25 degrees C. Scatchard analysis of the equilibrium binding data for metal ions on S. coelicolor A3(2) gave rise to a linear plot, indicating that the Langmuir model could be applied. However, for nickel(II) ion, divergence from the Scatchard plot was evident, consistent with the participation of secondary equilibrium effects in the adsorption process. Adsorption behaviour of nickel(II) and copper(II) ions on the S. coelicolor A3(2) can be expressed by both the Langmuir and Freundlich isotherms. The adsorption data with respect to both metals provide an excellent fit to the Freundlich isotherm. However, when the Langmuir isotherm model was applied to these data, a good fit was obtained for the copper adsorption only and not for nickel(II) ion.     

Interaction of Ag(I), Hg(II), and Cu(II) with 1,2-ethanedithiol immobilized on chitosan: thermochemical data from isothermal calorimetry

The nature of interactions between metal ions Ag(I), Hg(II), Cu(II) and chitosan derivative of 1,2-ethanedithiol, QTDT, was investigated by isothermal calorimetry using the membrane breaking technique. Simultaneous determination of thermal effects, Q(int), and amount of cation that interacts, n(int), are described. The experimental data have been interpreted in terms of the Langmuir equation to determine the maximum adsorption capacity to form a monolayer, N(mon), and the energy of interaction for a saturated monolayer per gram of QTDT, Q(mon). With N(mon) and Q(mon), the molar enthalpy of interaction for formation of a monolayer of anchored cations per gram of QTDT, Delta(mon)H(m), was determined. The Delta(mon)H(m) values for Ag(I), Hg(II), and Cu(II) were -60.56, -58.05, and -84.36 kJ mol(-1), respectively. Negative values of DeltaG show the spontaneity of the interaction processes. The least entropically favourable processes, i.e., those which present more negative DeltaS values, seem to be compensated by the more favourable enthalpic parameter.     

Biosorption of Au (III) and Cu (II) from aqueous solution by a non-living Cetraria islandica (L.) Ach

Biosorption of Au(III) and Cu(II) from dilute aqueous solutions was investigated by biomass of the non-living Cetraria islandica (L.) Ach. The removal and recovery of gold and copper were studied by applying batch technique. The experimental parameters such as the pH of the solution, contact time, the amount of Cetraria islandica (L.) Ach. (dried lichen), the concentration of metals on retention and eluents kind and amount have been investigated. Au(III) and Cu(II) were adsorbed on the dried lichen at pH 3 and pH 8, respectively. Quantitative retention (> or = 90%) was obtained within 60 minutes for metals. Maximum capacity of 1.0 g of dried lichen for biosorption of Au(III) and Cu(II) were found as 7.4 mg of Au(III) and 19.2 mg of Cu(II). It was seen that the adsorption equilibrium data conformed well to the Langmuir model and Freundlich equation for Au(III) and only Freundlich equation for Cu(II). The method proposed in this study was applied to spiked mineral water analysis and metals adsorbed on the lichens were quantitatively (> or = 90%) recovered from mineral water samples by using 0.5 mol L(-1) HCl.     

Isotherm, kinetic and thermodynamic studies of lead and copper uptake by H2SO4 modified chitosan

The kinetic and thermodynamic adsorption and adsorption isotherms of Pb(II) and Cu(II) ions onto H₂SO₄ modified chitosan were studied in a batch adsorption system. The experimental results were fitted using Freundlich, Langmuir and Dubinin–Radushkevich isotherms; the Langmuir isotherm showed the best conformity to the equilibrium data. The pseudo-first order, pseudo-second order and intraparticle diffusion kinetic models were employed to analyze the kinetic data. The adsorption behavior of Pb(II) and Cu(II) was best described by the pseudo-second order model. Thermodynamic parameters such as free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were determined; the adsorption process was found to be both spontaneous and exothermic. No physical damage to the adsorbents was observed after three cycles of adsorption/desorption using EDTA and HCl as eluents. The mechanistic pathway of the Pb(II) and Cu(II) uptake was examined by means of Fourier transform infrared (FTIR) and Energy dispersive X-ray (EDX) spectroscopy. The equilibrium parameter (R_L) indicated that chitosan–H₂SO₄ was favorable for Pb(II) and Cu(II) adsorption.