Effects of ionization on the phase behavior of poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide-co-acrylic acid) and poly(<Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-diethylacrylamide-co-acrylic acid) in water

Phase transitions of poly(N-isopropylacrylamide-co-acrylic acid) (PiPA-AA) and poly(N,N- diethylacrylamide-co-acrylic acid) (PdEA-AA) in water have been investigated by means of turbidimetry, Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC). The phase transition temperatures (T_p) of these copolymers increase with the degree of ionization () of the acrylic acid (AA) units, which in turn is dependent on the pH of the solutions. Apparent values of pK_a for the AA units, determined from the pH dependencies of T_p, are 4.7 and 5.4 for PiPA-AA and PdEA-AA, respectively. Differences between T_p for PiPA-AA and T_p for PiPA homopolymer (T_p) are +1.5 and –0.2 °C/mol% of AA at =1 and 0, respectively. The values of T_p for PdEA-AA are +2.6 (ionic) and –0.5 (nonionic)°C/mol%, indicating that the incorporated AA units have a larger effect on PdEA than on PiPA. DSC measurements performed with each of these copolymers at different pH values show a linear relationship between T_p and the enthalpy of transition (H). IR measurements of PiPA-AA show that the profiles of IR bands from both iPA and AA units exhibit critical changes at T_p of the copolymer. Heating the solution above T_p leads to shifts of the amide II, C–H stretch, and C–H bend bands from the iPA units toward lower wavenumbers, as well as a shift of the amide I band from the iPA units toward higher wavenumbers. A decrease in the intensity of the symmetric C=O stretch IR band from carboxylate anions (1560 cm^–1), and an increase in the intensity of the C=O stretch band from COOH groups (1705 cm^–1) suggest that a partial protonation of the carboxylate groups (COO^–+H⁺COOH) takes place upon the phase transition.     

A new strategy to prepare temperature-sensitive poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) microgels

In this study, a new method was developed to prepare temperature-sensitive poly(N-isopropylacrylamide) microgels by free radical precipitation polymerization using siloxane coupling agent as the new crosslinker. Ammonium persulfate acted as the initiator for the radical copolymerization as well as the catalyst for the hydrolysis/condensation of the siloxane groups. The particle diameter and polydispersity of the microgels were measured by photon correlation spectroscopy and the results display that the microgels are monodisperse. The microgels exhibit temperature sensitivity and the phase transition temperature is approximately 31 °C. Furthermore, the diameter of the microgels changes upon heating and cooling processes. These were observed to be reversible. The novel crosslinking method described herein is the condensation of siloxane groups, which is totally different from the traditional double-vinyl crosslinkers. This innovative approach offers an alternative path to prepare functional core–shell particles and inorganic/organic hybrid materials.     

Electrochemical preparation and <Emphasis Type="Italic">in situ</Emphasis> characterization of poly(3-methylpyrrole) and poly(3-methylpyrrole-cyclodextrin) films on gold electrodes

A Electrosynthesis of conducting poly(3-methylpyrrole) (P3MPy) and poly(3-methylpyrrole-2,6-dimethyl-β-cyclodextrin) (poly(3MPy-β-DMCD)) films on a gold electrode in acetonitrile electrolyte solution containing lithium perchlorate has been carried out by potential cycling. Products were characterized with cyclic voltammetry CV, in situ UV-Vis spectroscopy, and in situ resistance measurements. Electrosynthesis of poly(3MPy-β-DMCD) started with a (1:1) (3MPy-β-DMCD) supramolecular cyclodextrin CD complex of 3-methylpyrrole characterized with proton NMR spectroscopy. The oxidation peak of poly(3MPy-β-DMCD) in CVs is shifted to more positive values than P3MPy. In situ resistance measurements show that the resistance of poly(3MPy-β-DMCD) is higher than of P3MPy by approximately an order of magnitude. Minimum resistance can be observed for P3MPy and poly(3MPy-β-DMCD) at 0.40 < E _Ag/AgCl < 1.10 V and 0.60 < E _Ag/AgCl < 1.10 V, respectively. The higher resistance of P3MPy compared with polypyrrole may result from the presence of the methyl group substituent resulting in a decreased conjugation length. When CD is present during synthesis, resistance is even higher. In situ UV-Vis spectroelectrochemical data for both films prepared potentiodynamically by cycling the potential in the range −0.20 < E _Ag/AgCl < 1.10 V in acetonitrile electrolyte show major effects of CD presence during electrosynthesis.      

New acyl derivatives of <Emphasis Type="Italic">N</Emphasis>-deacetyllappaconitine

New N-acylates of the norditerpenoid alkaloid N-deacetyllappaconitine that were modified in the aromatic ring and are interesting as potential pharmacologically valuable compounds were prepared. __________ Translated from Khimiya Prirodnykh Soedinenii, No. 3, pp. 275–279, May–June, 2008.     

Fast responsive poly(<Emphasis Type="Italic">N,N</Emphasis>-diethylacrylamide) hydrogels with interconnected microspheres and bi-continuous structures

We prepared thermo-responsive polymer hydrogels by γ-ray irradiation of aqueous solutions of N, N-diethylacrylamide at different temperatures below and above its lower critical solution temperature (LCST). Poly(N, N-diethylacrylamide) gel had a transparent and homogeneous structure when the radiation-induced polymerization and crosslinking were carried out below the LCST (25 °C) of the polymer. On the other hand, cloudy and heterogeneous gels were formed at temperatures above the LCST of the polymer (>35 °C). From environmental scanning electron microscopy observations, the gels prepared at 35 and 40 °C were seen to show sponge-like bi-continuous porous structures, while those prepared at 50 °C showed a porous structure consisting of interconnected microspheres. For temperature changes between 10 and 40 °C, gels with porous structures showed rapid volume transitions on a time scale of about a minute, not only for shrinking but also for swelling processes, which is in remarkable contrast to the porous poly(N-isopropylacrylamide) hydrogels.     

Synthesis and characterization of thermoresponsive poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide-co-<Emphasis Type="Italic">N</Emphasis>-hydroxymethylacrylamide-co-2-hydroxyethyl methacrylate) hydrogels

Thermoresponsive hydrogels based on N-isopropylacrylamide, N-hydroxymethylacrylamide, and 2-hydroxyethyl methacrylate, poly(NIPAM–co-NHMAAm–co-HEMA), have been synthesized and their swelling—deswelling behavior studied as a function of NIPAM concentration, NIPAM/NHMAAm and NIPAM/HEMA mole ratio, and total monomer concentration. Copolymers varying in composition have been obtained by redox copolymerization of these three monomers. Temperature has been changed in the ranges from 4 to 70 °C at fixed pH and total ionic strength. Equilibrium swelling ratio, dynamic swelling ratio, and dynamic deswelling ratio were evaluated for all hydrogel systems. The equilibrium swelling ratios of the copolymeric gels decrease with increasing NHMAAm and HEMA content. The formation of the intermolecular hydrogen bonding between hydroxyl and amido groups decreases the hydrophilic group numbers of the gel and the affinity of the gel towards water decreases. The copolymer gels also showed rapid volume transitions with time. The time required for equilibrium shrinking increased with increasing NHMAAm and HEMA content in the gel.     

pH sensitivities of egg phosphatidylcholine liposomes and dioleoylphosphatidylethanolamine liposomes triggered by poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide-co-methacrylic acid-co-octadecylacrylate)

Egg phosphatidylcholine (PC) liposomes bearing pH-sensitive polymers and dioleoylphosphatidylethanolamine (DOPE) liposomes including the same polymers were prepared by a sonication method. As pH-sensitive polymers, copolymers of N-isopropylacrylamide, methacrylic acid, and octadecylacrylate were used. The liposomes were stable in neutral pH ranges in terms of release. But the release became marked at pH 5.5, and it was accelerated as pH further decreased. For example, the degree of release from egg PC liposomes (polymer/lipid ratio is 3:10, w/w) for 120 s increased from 2% to 63% as pH decreased from 7.5 to 4.5. Under the same condition, the degree of release from DOPE liposomes increased from 4% to 80%. These results indicate that DOPE liposome is more pH-sensitive than egg PC liposome.     

Dynamics studies on thermoresponsive poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) hydrogel in tetrahydrofuran/water mixtures

The properties of thermoresponsive poly(N-isopropylacrylamide) (PNIPAAm) hydrogel in tetrahydrofuran/H₂O mixtures were studied. Scanning electron microscopic (SEM) images demonstrate that the hydrogel changes from homogeneous to heterogeneous microstructure upon the addition of tetrahydrofuran to water. This heterogeneous PNIPAAm hydrogel in the mixture solvent exhibits a very slow response rate at temperatures above its lower critical solution temperature. The decreased response rate is attributed to the formation of special ternary complexes including the polymer and the two solvents in the tetrahydrofuran/H₂O mixture. Factors controlling the thermoresponse rate are discussed further and several suggestions are provided for designing and developing fast-response PNIPAAm hydrogels in the future.     

Adsorption of<Emphasis Type="Italic"> N</Emphasis>-dodecyl-<Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-dimethyl-3-ammonio-1-propanesulfonate (DDAPS), a model zwitterionic surfactant,on the Au(111) electrode surface

Electrochemical measurements including cyclic voltammetry, differential capacity, and chronocoulometry have been used to characterize the adsorption behaviors of the zwitterionic surfactant N-dodecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (DDAPS) on the Au(111) electrode surface. The thermodynamics of the ideally polarized electrode have been employed to determine the Gibbs excess and the Gibbs energy of adsorption. The results show that the adsorption of DDAPS has a multistate character. The first two states are observed at potentials close to zero charge. At low bulk DDAPS concentrations, it corresponds to the formation of a film of nearly flat adsorbed molecules. At higher concentrations it is converted into a hemimicellar state. The second state is formed at negative potentials and charge densities close to 0 C cm^–2. It corresponds to a film of tilted molecules oriented with the hydrocarbon tail towards the metal and the polar head toward the solution.Dedicated to Professor Zbigniew Galus on the occasion of his 70^th birthday and in recognition of his many contributions to electrochemistry.     

Temperature- and pressure-responsive properties of <Emphasis Type="SmallCaps">l</Emphasis>- and<Emphasis Type="SmallCaps"> dl</Emphasis>-forms of poly(<Emphasis Type="Italic">N</Emphasis>-(1-hydroxymethyl)propylmethacrylamide) in aqueous solutions

The structural transition of the l- and dl forms of poly(N-(1- hydroxymethyl)propylmethacrylamide (PHMPMA) in aqueous solution was studied by measuring the pressure dependence of the apparent scattering intensity, differential scanning calorimetry (DSC), and circular dichroism (CD). The thermodynamic implications of the results are discussed in relation to the chiral structure of the side chain, and differences in the thermal and barometric transitions. T-P diagrams of the transition showed characteristic ellipsoid features. Antagonism of the temperature and pressure effects was observed only for P(dl-HMPMA). For P(l-HMPMA), the transition temperature (T _tr) decreased with increasing pressure, and the highest T _tr was observed at atmospheric pressure (0.1 MPa). For both polymers, the highest P _trs were observed at the lowest temperatures. The l polymer showed a specific negative peak in its CD spectrum at around 220 nm in the lower temperature region and the temperature dependence was reproduced by a single-step transition, with the midpoint corresponding to the T _tr obtained from the scattering measurements. Coupled with the results from the DSC, the different behavior between the P(l-HMPMA) and P(dl-HMPMA) could be explained in terms of the chain states before and after the transition. The cooperative factors derived from the DSC measurement revealed that about 4 to 5 polymers of the present size were necessary to perform a thermal transition for P(l-HMPMA), and that P(dl-HMPMA) underwent its transition as an almost single molecular event.This revised version was published online in June 2005 with correction to the article category.     

Reactions of 3-nitro-2-trihalomethyl-2<Emphasis Type="Italic">H</Emphasis>-chromenes with indole, <Emphasis Type="Italic">N</Emphasis>-methylindole,and <Emphasis Type="Italic">N</Emphasis>-methylpyrrole. Stereoselective synthesis of 4-azolyl-3-nitro-2-trihalomethylchromanes

Heating of 3-nitro-2-trifluoromethyl-and 3-nitro-2-trichloromethyl-2H-chromenes with indole, N-methylindole, and N-methylpyrrole under solvent-free conditions led with high stereoselectivity and in good yields to cis-trans-3-nitro-2-trifluoromethyl-or trans-cis-3-nitro-2-trichloromethylchromanes substituted by the indol-3-yl (pyrrol-2-yl) fragment in position 4. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1985–1990, October, 2007.     

Determination of epoxides by high-performance liquid chromatography following derivatization with <Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-diethyldithiocarbamate

A reversed-phase, high-performance liquid chromatography (RP-HPLC) method that allows quantitation of low levels of epoxides has been described. The method involved derivatization of epoxides using 100- to 1,000-fold excess N,N-diethyldithiocarbamate (DTC) at 60 °C for 20 min at neutral pH. The unreacted DTC was then decomposed to CS₂ and diethyl amine by acidification of the reaction mixture to pH 2 using orthophosphoric acid. The first two steps could be performed in the same reaction vessel by sequential addition of reagents. In the final step, an aliquot (20 μL) of the derivatized sample was analyzed for the presence of stable esters of DTC by RP-HPLC using a Supelcosil LC-18-S (150 × 4.6-mm) column and a mobile phase consisting of 40% (v/v) acetonitrile in water at a flow of 1 mL min⁻¹. Using UV detection at 278 nm, the epoxides gave linear responses in the concentration range of 0.25 to 50 μM. The method is robust, and as low as 5 pmol of the analyte could be successfully detected and quantified with recoveries of ≥94%. Following a minimal pretreatment such as ultrafiltration (molecular weight cutoff 5,000 Da), the method is suitable for analysis of epoxides in complex physiological fluids (e.g., fetal bovine serum). The method has been rigorously evaluated and adapted in our laboratory for routine analysis and determination of stability of epoxides of 1,3-butadiene and other alkenes added to cell cultures.     

Synthesis of amphiphilic diblock copolymers poly[2-(<Emphasis Type="Italic">N</Emphasis>, <Emphasis Type="Italic">N</Emphasis>-dimethylamino)ethyl methacrylate]-<Emphasis Type="Italic">b</Emphasis>-poly(stearyl methacrylate) and their self-assembly in mixed solvent

Amphiphilic diblock copolymers consisting of 2-(N, N-dimethylamino)ethyl methacrylate (DMAEMA, abbreviated as DMA) and stearyl methacrylate (SMA) with different degrees of polymerization and compositions were prepared by reversible addition–fragmentation chain transfer (RAFT) copolymerization. The composition and chemical structures of (co)polymers were confirmed by the measurements of ¹H NMR spectroscopy and gel permeation chromatography (GPC). The self-aggregating structures of amphiphilic diblock copolymers with the concentration of 0.1~0.3 wt.% in THF/water mixed solvent was investigated by transmission electron microscopy (TEM) and dynamic light scattering (DLS). It was found that both the morphologies and aggregating particle size resulted from the amphiphilic diblock copolymers depended on the variation of pH values, the lengths of the hydrophobic PSMA chains, and the weight ratio of THF/water mixed solvent.     

Interaction and Scale of Mixing in Cellulose Acetate/Poly(<Emphasis Type="Italic">N</Emphasis>-vinyl Pyrrolidone-co-vinyl Acetate) Blends

Binary blends and pseudo complexes of cellulose acetate (CA) with vinyl polymers containing N-vinyl pyrrolidone (VP) units, poly(N-vinyl pyrrolidone) (PVP) and poly(N-vinyl pyrrolidone-co-vinyl acetate) [P(VP-co-VAc)], were prepared, respectively, by casting from mixed polymer solutions in N,N-dimethylformamide as good solvent and by spontaneous co-precipitation from solutions in tetrahydrofuran as comparatively poor solvent. The scale of miscibility and intermolecular interaction were examined for the blends and complexes by solid-state ¹³C-NMR spectroscopy. It was revealed that the formation of complexes was due to a higher frequency of hydrogen-bonding interactions between the residual hydroxyl groups of CA and the carbonyl groups of VP residues in the vinyl polymer component. From measurements of CP/MAS spectra and proton spin-lattice relaxation times (T_1ρ^H) in the NMR study, the existence of the hydrogen-bonding interaction was also confirmed for the miscible blends and the homogeneity of the mixing was estimated to be substantially on a scale within a few nanometers.     

Electrooxidation of undiluted organic liquids swelling<Emphasis Type="Italic"> N</Emphasis>-isopropylacrylamide-based copolymers

Polyacrylate gels such as: N-isopropylacrylamide (NIPA), ionic copolymer NIPA-co-sodium acrylate (NIPA-co-SA) and ionic copolymer NIPA-co-[2-(acryloyloxy)ethyl]trimethylammonium chloride (NIPA-co-XCl) were swollen by methanol, ethanol and N,N-dimethylformamide. These solvents were oxidized voltammetrically in the gels at platinum microelectrodes. The blocking coefficients, defined as the ratio of the currents observed in the presence and absence of the polymeric chains, were different for the solvents in the charged and uncharged polymers and did not differ for the electroactive probe, ferrocene, present in the solvents at millimolar level. This may mean that the micro ionic layer that is formed at microelectrodes at the plateau of the voltammetric solvent waves leads to a kind of collapse/phase transition of the polymer in the depletion layer. For methanol, the gel structure was found to prevent occasionally the formation of large gas bubbles at the potentials positive versus the first wave and then three one-electron waves could be obtained. Experiments done with a capillary cell and an optical microscope indicated that before formation of large bubbles at the Pt microelectrode a very dynamic, dense stream of microbubbles leaves the electrode surface.Dedicated to Zbigniew Galus on the occasion of his 70th birthday     

Synthesis of graft copolymers of wood and <Emphasis Type="Italic">N</Emphasis>-vinylpyrrolidone

Lignocellulose copolymers with grafted lactam rings were prepared by graft copolymerization of wood with N-vinylpyrrolidone initiated by Fe²⁺-H₂O₂. The principal features of their formation were investigated as functions of reactant concentrations, temperature, and polymerization time. __________ Translated from Khimiya Prirodnykh Soedinenii, No. 2, pp. 174–176, March–April, 2008.     

Hexafluoroacetone as Protecting and Activating Reagent. A New Approach to <Emphasis Type="Italic">N</Emphasis>-Glycosides

Summary. N-Glycosides of Asn and homologues have been synthesized starting from hexafluoroacetone-protected -activated Asp, Glu, and Aad derivatives and glycosylamines. The synthetic value of the new building blocks was demonstrated by the concise incorporation of N-glycosylated Asn, Gln, and Aad -amides into glycopeptides.     

Starch Derivatives of High Degree of Functionalization 11: Studies on Alternative Acylation of Starch with Long-chain Fatty Acids Homogeneously in <Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-dimethyl acetamide/LiCl

Starch materials of different amylose content were allowed to react with saturated and unsaturated fatty acids of varying chain length from C₁₄ to C₁₈ under homogeneous conditions applying the solvent N,N-dimethyl acetamide in combination with LiCl. As reagent the corresponding acid chlorides and, alternatively, carboxylic acids in situ activated with toluene-4-sulfonyl chloride and N,N′-carbonyldiimidazole (CDI) were studied. Using fatty acid chlorides (FACl) and toluene-4-sulfonyl chloride-activated acids an almost complete substitution of the starch occurs. By in situ activation of the fatty acids with CDI, products with a degree of substitution up to 2 were obtained, which, in particular, represents a simple and very mild procedure.     

Convenient synthesis and NMR spectral studies of variously substituted <Emphasis Type="Italic">N</Emphasis>-methylpiperidin-4-one-<Emphasis Type="Italic">O</Emphasis>-benzyloximes

Abstract  A series of variously substituted N-methylpiperidin-4-one-O-benzyloximes were synthesized by three different methods. Among them, the direct conversion of 2,6-diarylpiperidin-4-ones into the corresponding oxime ethers (method A) was proved to be better than the other two methods in the sense of good yield, convenience, easy work-up and quick reaction time. All the synthesized compounds are characterized by IR, Mass and NMR (¹H NMR, ¹³C NMR, ¹H-¹H COSY, ¹H-¹³C COSY and HMBC) spectral studies. The conformational preference of the synthesized oxime ethers with/without alkyl and aryl substituents at C-3/C-5 and C-2/C-6 is discussed using the spectral data. The observed chemical shifts and coupling constants suggest that the synthesized oxime ethers adopt chair conformation with equatorial orientation of all the substituents, whereas 1-methyl-3-isopropyl-2,6-diphenylpiperidin-4-one-O-benzyloxime also exists in boat conformation. Based on the NMR data, the effects of oximination on ring carbons and their associated protons and alkyl substituents are discussed. In addition, the effect of NMe group on the 2,6-diarylpiperidin-4-one-O-benzyloximes was also studied. Graphical abstract        

Effect of Cu(II) on the electrochemically initiated reaction of thiols with<Emphasis Type="Italic"> N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-diethyl-<Emphasis Type="Italic">p</Emphasis>-phenylenediamine: methodology for the indirect voltammetric determination of Cu(II)

The effect of Cu(II) on the determination of homocysteine via its electrochemically initiated reaction with N,N-diethyl-p-phenylenediamine is examined. The presence of copper inhibited the detection process for homocysteine owing to a complexation reaction occurring. This provided an indirect route for the sensitive and selective determination of Cu(II), which produced a linear response over the range from 2.5 to 500 M and a limit of detection of 2.5 M. The detection pathway was examined in the presence of metallic and inorganic ions, with negligible interference observed.