溶胶-凝胶膜修饰碳酸根离子选择电极的研究

利用溶胶-凝胶技术包埋电活性物质,制备溶胶-凝胶膜修饰的碳酸根离子选择电极。探索了Sol-Gel膜修饰CO32-选择电极的制备方法、测试条件及共存物的影响。电极的线性范围1.0×10-1~1.0×10-5mol/L,相关系数R2=0.993,检测限8.9×10-6mol/L,响应斜率22.1 mV/pCO3。电极稳定性和重现性良好,用于实际样品测定,回收率95.9%~99.0%。     

溶胶-凝胶法修饰的硫氰酸根离子选择性电极(ISE)的研究

报道了一种基于溶胶-凝胶技术的新型硫氰酸根电极,讨论了电极性能的影响因素.该电极有良好的能斯特响应,斜率为63 mV/pC,线性范围为1.0×10-2～6.0×10-6mol/L,检出限为4.0×10-6 mol/L,适宜的pH范围为3.4～7.1.     

Measuring quaternary ammonium cleaning agents with ion selective electrodes

Data for coated-wire, ion selective electrodes (ISEs) are presented for cationic surfactant ions found in common cleaners including benzyldimethyltetradecylammonium, benzyldimethyldodecylammonium, and benzyldimethylhexadecylammonium. The ion exchangers dinonylnaphthalene sulfonic acid, tetraphenyborate, and tetrakis(4-chlorophenyl)borate are examined, showing dinonylnaphthalene sulfonic acid to be the favored species. The ISEs exhibit approximately Nernstian behavior down to the 10⁻⁶ M limit of detection with lifetimes in excess of 50 days when used continuously, and a shelf life of over 100 days. Reaching the upper detection limit at the critical micelle concentration requires use of polymeric-membrane reference electrodes including a new membrane cocktail, which allow response measurements of an order of magnitude higher than the traditional fritted-glass reference electrode. The surfactant ISEs show excellent selectivity over the common metal ions Na⁺, K⁺, Mg²⁺, Ca²⁺, and Cu²⁺ with selectivity coefficients less than 10^−5.3. The ISEs are also selective over the lower molecular weight quaternary ammonium ions tetradecyltrimethylammonium, dodecyltrimethylammonium, benzyldimethyl(2-hydroxyethyl)ammonium, and tetrabutylammonium with selectivity coefficients ranging from 10^−1.7 to 10^−5.5. Use of a single electrode to determine accurately the total cationic surfactant concentration in common cleaning solutions is accomplished with information about concentration dependent interferences and a modified Nikolsky–Eisenman model. Finally, quaternary ammonium surfactants have a deleterious effect on the measurements of pH and common ions like K⁺, Mg²⁺ and Ca²⁺ with polymeric ISEs. This makes it critical to include surfactant electrodes in a detector array when cleaning agents are present.     

Highly sensitive and selective spectrofluorimetric determination of tolnaftate through the formation of ternary inclusion complex of beta-naphthol/beta-cyclodextrin/anionic surfactant system

An indirect spectrofluorimetric method with high sensitivity and selectivity was developed for the determination of antifungal drug: tolnaftate (TNF), depending on the supramolecualr multirecognition interaction among the anionic surfactant sodium laurylsulfate (SLS), β-cyclodextrin (β-CD) and β-naphthol (ROH). The mechanism of the inclusion was studied and discussed by means of fluorescence spectrum, infra-red spectrograms and ¹HNMR spectroscopy. Results showed that the naphthalene ring of ROH and the hydrophobic hydrocarbon chain of SLS were included into the β-CD's cavity to form a ROH:SLS:β-CD ternary inclusion complex with stoichiometry of 1:1:1 at room temperature, which provided effective protection for the excited state of ROH. At λ_ex/λ_em = 273/360 nm, the fluorescence intensity was linear over a tolnaftate concentration range of 2.46 × 10⁻⁹ to 2.10 × 10⁻⁶ mol L⁻¹. The detection limit and relative standard deviation was 7.50 × 10⁻¹⁰ mol L⁻¹ and 1.4%, respectively. The interference of 31 foreign substances was slight. The proposed method had been successfully applied to the determination of tolnaftate in artificial mixed samples with almost quantitative recovery.     

氧氟沙星选择性电极的改进研究及应用

分别以氧氟沙星-磷钼酸与氧氟沙星-四苯硼钠离子缔合物作为电活性物质制备氧氟沙星选择性电极,并系统研究和比较了这两种电极的响应性能。实验表明以磷钼酸-氧氟沙星离子对作为电活性物质,以四苯硼钠作添加剂所制备的氧氟沙星电极呈现了良好的Nernst响应,且其选择性明显提高。用该电极测定了药物中的氧氟沙星。     

涂碳型PVC膜培氟沙星选择电极的研制

报道一种以盐酸培氟沙星与溴汞酸盐生成的分子缔合物为电活性物质的新型涂碳PVC膜培氟沙星选择电极。在pH 1 .5～ 4.5范围内 ,电极对培氟沙星的Nernst响应范围为 1 .0× 1 0 - 2 ～ 5 .0× 1 0 - 5mol/L ,检测限为 4.2× 1 0 - 6mol/L。方法的平均回收率为 98.5 % ,RSD为 1 .0 %     

Zirconium ion selective electrode based on bis(diphenylphosphino) ferrocene incorporated in a poly(vinyl chloride) matrix

A novel potentiometric zirconium - PVC matrix membrane sensor incorporating bis(diphenylphosphino) ferrocene as an electroactive material and tris(2-ethylhexyl)phosphate as solvent mediator is described. In mixed acetate buffer solution of pH 4.8, the sensor displays a rapid and linear response for zirconium ion over the concentration range 1.0 × 10⁻¹ to 1.0 × 10⁻⁷ mol L⁻¹ with a good slope of 59.7 ± 0.3 mV per decade and detection limit 1.8 × 10⁻⁸ mol L⁻¹. The best performance was obtained with membrane composition 33% PVC, 65% TEHP, 1% NaTPB and 1% ionophore. The proposed electrode revealed excellent selectivity for zirconium ion over a wide variety of alkali, alkaline earth, transition and heavy metal ions and could be used in a pH range of 4.15-7.8. The electrode was applied for at least 1 month without any considerable divergence in the potential responses. The practical utility of the electrode has been demonstrated by its use as an indicator electrode in the potentiometric titration of zirconium ions with sodium fluoride and in determination of zirconium ion in some alloy, tape and waste water samples.     

溶胶-凝胶法修饰的一次性氯离子选择性电极的研究

溶胶-凝胶法(sol-gel)对固定试剂的种类和数量具有可调性,又具有保持性能稳定的潜在优势;一些小分子离子可以自由进出sol-gel的孔径,使得sol-gel基质内外浓度相等,因而可制备化学电极。本文通过正硅酸乙酯[TEOS]在适宜的酸催化下,水解制得电极材料,采用溶胶．凝胶掺杂技术,成功地修饰了新型氯离子选择性电极,这种电极的线性范围和AgCl-AgS2固态膜电极、     

Demicellization of a mixture of cationic-anionic hydrogenated/fluorinated surfactants through selective inclusion by alpha- and beta-cyclodextrin

The interactions between alpha- and beta-cyclodextrin (alpha-/beta-CD) and an equimolar mixture of octyltriethylammonium bromide (OTEAB) and sodium perfluorooctanoate (SPFO) were studied by 1H and 19F NMR, surface tension, conductivity, and dynamic light scattering. It was shown that beta-CD could destroy the mixed micelles of OTEAB-SPFO by selective inclusion of SPFO. As beta-CD was added, the system was observed to undergo a process like this: beta-CD preferentially included SPFO to form 1:1 beta-CD/SPFO complexes. As the inclusion of SPFO was almost saturated, the mixed micelles broke and all OTEAB was released and exposed to aqueous surroundings. Then 1:1 beta-CD/OTEAB and 2:1 beta-CD/SPFO complexes significantly formed simultaneously. Contrary to beta-CD, alpha-CD exhibited selective inclusion to OTEAB and only weak association with SPFO. alpha-CD could also destroy the mixed micelles of OTEAB-SPFO; however, the demicellization ability of alpha-CD is much smaller than that of beta-CD. These conclusions were also well supported by the calculations of binding constants and DeltaG degrees . Different from the complexes of CD/conventional surfactants, the complexes of beta-CD/SPFO or alpha-CD/OTEAB formed by selective inclusion of CD in the mixed cationic-anionic surfactants may have contributed to the surface activity of the aqueous mixtures. The complexes of alpha-CD/OTEAB showed much more significant contribution to the surface activity than that of the complexes of beta-CD/SPFO.     

Potentiometric detection of monovalent anions separated by ion chromatography using all solid-state contact PVC matrix membrane electrode

Summary An all solid-state contact tubular PVC-matrix membrane electrode has been applied for potentiometric detection of inorganic and organic monovalent anions using phosphate and hydrogen phosphate eluents at low concentrations. This is a “monovalent detection method” as the selectivity of the electrode towards monovalent anions results in some other anions being undetected unless the concentration of those other anions is higher than 10⁻³ mol dm⁻³ in the sample solution injected. It takes only eight minutes to complete the separation with a good resolution. Theoretical and practical considerations are discussed, and in particular, sensitivity, linearity, detection limit and dynamic behaviour are presented. The use of an all solid-state contact bromide-selective electrode as a detector offers so far the best simultaneous sensitivity toward all anions when compared with other detection methods. Determination of Cl⁻ and NO₃ ⁻ ions in river, rain and drinking water samples without any further sample preconcentration has been successfully achieved. The detection limit is sub-ppb for most of anions in a 20 μL injection volume.     

碘离子选择电极检测催化动力学分析法测定抗坏血酸

在稀硫酸介质中，痕量去氢抗坏血酸对Ｖ（Ｖ）－ＢｒＯ３＾－－Ｉ＾－反应有强烈的催化作用，体系中Ｉ＾－浓度的变化可供碘离子选择电极跟踪检测。据此，本文建立了测定６×１０＾－７￣２×１０＾－５ｍｏｌ／Ｌ抗坏血酸的催化动力新分析法，用于实际样品分析获得较好结果。     

Morpholinoethanesulfonic acid-based buffer system for improved detection limit and stability of the fluoride ion selective electrode

The zwitterionic morpholinoethanesulfonic acid (MES) is used as the basis for the development of a new total ionic strength adjustor buffer system for improving the analytical characteristics of fluoride sensor. Impedance analysis, atomic force microscopy (AFM) and dissolution studies of the LaF₃ crystal, together with the potential stability and sensor sensitivity over time have aided in the elucidation of the processes that take place at the surface of the LaF₃ crystal, that seem to determine the sensor behaviour. Even though AFM analysis shows that both buffers used (MES or acetate) cause a similar increase in surface roughness, the data from the other studies suggest that in the first case there is a reversible ion exchange process at the interface, while in the second case this process is irreversible, leading to fast poisoning of the crystal surface. The use of 0.5 M MES and NaCl buffer adjusted to pH 5.50 allows for the continuous operation of the sensor under flow injection analysis conditions for at least 5 days with sensitivity of 60 mV per decade [F⁻], detection limit of 2.1×10⁻⁷ M [F⁻] and fast response time.     

基于碘离子选择性电极的流动注射分析系统构建

碘硫(IS)热化学循环分解水是目前最有前景的核能制氢技术.在IS循环研究中,I-浓度的在线分析对于实现过程反应条件的监测控制以及进行有关反应动力学研究非常重要.以碘离子选择性电极为检测器,针对IS循环物料组成体系组装了一套流动注射分析系统,考察了样品温度、氢离子浓度、离子强度等因素对电极性能的影响,对FLA装置的栽流流...     

A novel chemically modified carbon paste electrode based on a new mercury(II) complex for selective potentiometric determination of bromide ion

A new modified carbon paste electrode based on a recently synthesized mercury (II) complex of a pyridine containing proton transfer compound as a suitable carrier for Br⁻ ion is described. The electrode has a linear dynamic range between 3.00×10⁻² and 1.0×10⁻⁵ M with a near-Nernastian slope of 61.0±0.9 mV per decade and a detection limit of 4.0×10⁻⁶ M (0.32 ppm). The potentiometric response is independent of the pH of the solution in the pH range 4.0–8.3. The electrode possesses the advantages of low resistance, fast response and good over a variety of other anions. It was applied as an indicator electrode in potentiometric titration of bromide ions and for the recovery of Br⁻ from tap water.     

用氯离子电极同时测定阳离子表面活性剂的CMC及反离子缔合度

临界胶束浓度(CMC)是研究表面活性剂的一个重要参数,胶束的反离子缔合度(K)是重要的特性参数。本文以阳离子表面活性剂十烷基三甲基氯化铵(DTMAC)、十二烷基三甲基氯化铵(DTAC)、十四烷基三甲基氯化铵(TTAC)、十六烷基三甲基氯化铵(CTAC)和十八烷基三甲基氯化铵(OTAC)水溶液体系为研究对象,用氯离子选择电极分别测定了其水溶液体系胶束的CMC和K。     

Determination of the binding constant for the inclusion complex between procaine hydrochloride and beta-cyclodextrin by capillary electrophoresis

The apparent electrophoretic mobilities of procaine hydrochloride (μ_i) in a series of concentration of β-cyclodextrin were measured directly by capillary electrophoresis technology. A new mathematical treatment method is proposed, which based on the fact that the molar ratio of the inclusion complex was 1:1 established by spectrophotometry. Using the proposed method, the binding constant of the inclusion complex of procaine hydrochloride with β-cyclodextrin can be obtained easily. The determination result was in correspondence with those of the spectrophotometric and fluorescence methods.     

Determination of fluoride in drinking water and in urine of adolescents living in three counties in Northern Chihuahua Mexico using a fluoride ion selective electrode

This study was carried out to determine fluoride in drinking water and in urine of adolescents, ages 15-20 years, living in Northern Chihuahua Mexico. Participants are from a cross-sectional study on health effects of chronic fluoride exposure from drinking water. A total of 201 participants (106 female and 95 male) in the study were recruited from three counties. Samples of drinking water of each county were collected and analyzed using the U.S. EPA Fluoride Ion-Selective Method. Statistically significant difference of fluoride content in water was found among the three counties of recruitment (Cd. Juarez; 0.3 mg/L, Samalayuca, 1.0 mg/L, and Villa Ahumada, 5.3 mg/L). Fluoride content in wells and tap water samples of Villa Ahumada ranged from 5.0 to 5.7 mg/L. Fluoride content of these samples was above the level permitted by Mexican regulations. The fluoride content in bottled water obtained from local stores in Villa Ahumada ranged from 0.3 to 3.7 mg/l.Fluoride in urine samples of each participant was also analyzed using the U.S. EPA Ion-Selective Method. The mean fluoride urine concentration (reported in mg/g creatinine) in adolescents living in these counties was 0.792±0.39, 1.33±0.67 and 2.22±1.16 (Cd. Juarez, Samalayuca and Villa Ahumada), respectively. The high fluoride urinary levels found in participants from Villa Ahumada may be associated to the high fluoride level (5.3 mg/L) in dinking water.The accuracy of measurements was assessed with reference materials in water and in urine. Mean fluoride recovery was 99.0% and 99.6% in water and in urine, respectively. The levels obtained were within the assayed 5% confidence levels.     

Simultaneous analysis of anionic, amphoteric, nonionic and cationic surfactant mixtures in shampoo and hair conditioner by RP-HPLC/ELSD and LC/MS

A simple and simultaneous analysis method for four (anionic, amphoteric, nonionic, and cationic) classes of surfactants in shampoo and hair conditioner was newly developed. Analysis of the surfactants was performed using a reversed-phase HPLC (RPLC) combined with evaporative light scattering detection (ELSD) without any pre-treatment. An optimum analysis condition for the resolution of both four main surfactant mixtures used in shampoo and five main surfactants used in hair conditioner could be established under a gradient mobile phase condition with acetonitrile, tetrahydrofuran and water. The detection limits were 2.5-30 μg mL⁻¹ except for SLES (150 μg mL⁻¹), and the calibration curves, i.e. the log-log plots, were linear in the working range of 2.5-5250 μg mL⁻¹ with R² values of above 0.998. The observed precision was less than 5% R.S.D. The elution peaks were identified by a liquid chromatography-mass spectrometer (LC-MS) equipped with an electrospray interface operating in mixed-mode.     

Highly efficient and selective turn-off quenching of ligand-sensitized luminescence from europium imidazo[4,5-f]-1,10-phenanthroline complex by fluoride ion

A smart fluoride sensitive luminescence probe based on 1:2 complex of europium(III) with 2-(2-hydroxyphenyl)imidazo[4,5-f]-1,10-phenanthroline was prepared. The emission of europium ions via photosensitization of the ligand was completely quenched by addition of 2 equiv. of fluoride ions in DMSO. Spectroscopic analyses proved that the imidazolyl NH of the ligand was hydrogen-bonded with additive fluoride to form the 1:1 complex, leading to suppression of the photosensitization.     

Study on dynamic interfacial tension of 3-dodecyloxy-2-hydroxypropyl trimethyl ammonium bromide at liquid/liquid interface

Dynamic interfacial tension between aqueous solutions of 3-dodecyloxy-2-hydroxypropyl trimethyl ammonium bromide (R₁₂HTAB) and n-hexane were measured using the spinning drop method. The effects of the R₁₂HTAB concentration (the concentration below the CMC) and temperature on the dynamic interfacial tension have been investigated; the reason of the change of dynamic interfacial tension with time has been discussed. The effective diffusion coefficient, D_a, and the adsorption barrier, _a, have been obtained from the experimental data using the extended Word–Tordai equation. The results show that the dynamic interfacial tension becomes smaller while _a becomes higher with increasing R₁₂HTAB concentration in the bulk aqueous phase. D_a decreases from 5.56 × 10⁻¹² m⁻² s⁻¹ to 0.87 × 10⁻¹² m⁻² s⁻¹ while _a increases from 5.41 kJ mol⁻¹ to 7.74 kJ mol⁻¹ with the increase of concentration in the bulk solution of R₁₂HTAB from 0.5 × 10⁻³ mol dm⁻³ to 4 × 10⁻³ mol dm⁻³. Change of temperature affects the adsorption rate through altering D_a and _a. The value of D_a increases from 5.56 × 10⁻¹² m⁻² s⁻¹ to 13.98 × 10⁻¹² m⁻² s⁻¹ while that of _a decreases from 5.41 kJ mol⁻¹ to 5.07 kJ mol⁻¹ with temperature ascending from 303 K to 323 K. The adsorption of surfactant from the bulk phase into the interface follows a mixed diffusion–activation mechanism, which has been discussed in the light of interaction between surfactant molecules, diffusion and thermo-motion of molecules.