石墨炉原子吸收光谱分析中的铋原子化机理研究

石墨炉原子吸收光谱法已广泛地应用于合金[1]、矿石[2]和水[3,4]等样品中铋的测定.铋是易挥发元素,为寻找有效的化学改进剂,了解其原子化机理是很有必要的.关于机理研究已有文献报道[5,6],但加入化学改进剂后在石墨管中形成的生成物的结构及其原子化机理的研究还少见报道[7].本试验以硝酸镍、氯化钯、氯化钯-硝酸镁和氯化钯-硝酸镍为化学改进剂,通过实验确定在本实验仪器条件下测定铋的最佳化学改进剂为氯化钯.进而研究铋在化学改进剂作用下的原子化机理,以达到提高原子化效率的目的.     

石墨炉原子吸收法测定钢中铅的干扰抑制

研究了石墨炉原子化法测定钢铁中痕量铅的干扰情况，并进行了干扰抑制实验。提出了抑制干扰的方法。     

石墨炉原子吸收光谱法测定茶叶中的铅

采用石墨炉原子吸收光谱法测定茶叶中铅,以NH4H2PO4作为基体改进剂,提高了测定的灰化温度,消除了基体干扰.方法简便,快速,准确度高.通过对标准物质的多次测定,结果均在其保证值范围内,相对标准偏差为2.8%.对样品进行加标回收试验,回收率为96%～105%,方法检出限为0.12μg/L.     

Determination of lead in water samples by graphite furnace atomic absorption spectrometry after cloud point extraction

Cloud point extraction (CPE) has been used for the pre-concentration of lead, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and later analysis by graphite furnace atomic absorption spectrometry (GFAAS) using octylphenoxypolyethoxyethanol (TritonX-114) as surfactant. The chemical variables affecting the separation phase were optimized. Separation of the two phases was accomplished by centrifugation for 15 min at 4000 rpm. Under the optimum conditions i.e., pH 8.0, cloud point temperature 40 °C, [5-Br-PADAP] = 2.5 × 10⁻⁵ mol l⁻¹, [Triton X-114] = 0.05%, added methanol volume = 0.15 ml, pre-concentration of only 10 ml sample permitted an enhancement factor of 50-fold. The lower limit of detection (LOD) obtained under the optimal conditions was 0.08 μg l⁻¹. The precision for 10 replicate determinations at 5 μg l⁻¹ Pb was 2.8% relative standard deviation (R.S.D.). The calibration graph using the pre-concentration system for lead was linear with a correlation coefficient of 0.9984 at levels near the detection limits up to at least 30 μg l⁻¹. The method was successfully applied to the determination of lead in water samples.     

Study of some palladium-containing chemical modifiers in graphite furnace atomic absorption spectrometry

Several chemical modifiers based on palladium have been evaluated: the individual Pd(II) and the mixed modifiers Pd + Zr, Pd + W, Pd + Zr + citric acid, Pd + W + citric acid. The mechanisms by which these chemical modifiers stabilize analytes and control atomization have been suggested. Factors that might have an influence on the characteristic mass and non-spectral interferences are discussed. The advantages and limitations of the palladium-tungsten modifiers are shown.     

石墨炉原子吸收法快速测定血液中铅和镉

建立了快速测定血液中铅和镉的石墨炉原子吸收光谱法。使用5%硝酸溶液对样品进行脱蛋白处理,然后在旋涡混合器上振摇,离心后取上清液上石墨炉原子吸收进行测定。 结果表明,Pb、Cd工作曲线线性关系良好,相关系数均大于0.9994;方法检出限分别为4.32μg/L和0.27μg/L;Pb的回收率为91.60%～97.31%,镉的回收率为97.04%～98.86%;Pb测定的RSD（n=7）为2.35%,Cd测定的RSD（n=7）为1.53%。冻干牛血铅、镉标准物质GBW09139k和GBW09140k的测定值与参考值吻合。该方法快速准确,精密度、准确度、检出限等测定结果令人满意。可以作为日常血铅、血镉的检测的方法。     

石墨炉原子吸收光谱法测定大鼠血清中硒

通过考察不同基体改进剂效果,提出了以硝酸锶和硝酸钯做为混合基体改进剂。建立了用石墨炉原子吸收法测定牛血清和大鼠血清中痕量硒的分析方法。线性范围为0-120ng/mL,硒的检出限为0．095ng／mL,方法用于标准牛血清测定。结果与标准值基本吻合,大鼠血清测定标准加入回收率为102％。     

Influence of citric acid as chemical modifier for lead determination in dietary calcium supplement samples by graphite furnace atomic absorption spectrometry

Citric acid was used as a chemical modifier for Pb determination by graphite furnace atomic absorption spectrometry in dietary supplement samples (calcium carbonate, dolomite and oyster shell samples) and its efficiency was compared to the use of palladium. Pyrolysis and atomization curves were established without use of chemical modifier, with the addition of 20, 100 and 200 μg of citric acid, and with 3 μg of palladium. The citric acid modifier made possible the interference-free Pb determination in the presence of high concentrations of Ca and Mg nitrates. Acid sample digestion involving closed vessels (microwave-assisted and conventional heating) and acid attack using polypropylene vessels at room temperature were compared. All digestion procedures presented similar results for calcium carbonate and dolomite samples. However, for oyster shell samples accurate results were obtained only with the use of closed vessel systems. Analyte addition and matrix-matched standards were used for calibration. The characteristic mass for Pb using citric acid and palladium were 16 and 25 pg, respectively. The relative standard deviation (RSD) was always less than 5% when citric acid was used. The relative and absolute limits of detection were 0.02 μg g^− 1 and 8 pg with citric acid and 0.1 μg g^− 1 and 44 pg with the Pd modifier, respectively (n = 10, 3σ). The recovery of Pb in spiked calcium supplement samples (10 μg l^− 1) was between 98% and 105%. With the use of 100 μg of citric acid as chemical modifier, problems such as high background absorption and high RSD values were minimized in comparison to the addition of 3 μg of palladium.     

Effectiveness of palladium as a chemical modifier for the determination of lead in biological materials and foodstuffs by graphite furnace atomic absorption spectrometry

Summary A combination of 6 g palladium and 15 g magnesium nitrate is proposed as chemical modifier for lead determinations in biological materials and foodstuffs. The applicability of this modifier was investigated by the analysis of several types of samples, as compared to the classical NH₄H₂PO₄ and Mg(NO₃)₂ modifier. Direct determinations of lead against aqueous standard solutions can be performed in 3-fold diluted urine, 2-fold diluted milk and 6-fold diluted blood, when the proposed modifier is added. A method for lead determinations in potatoes using the combined palladium and magnesium nitrate modifier, after a microwave acid digestion, is described. The optimum GFAAS pyrolysis temperature remains dependent on the matrix and should be determined for each type of sample. A wider linear range of the calibration curve is observed when the proposed Pd modifier is used.     

样品基体化学改进剂-石墨炉原子吸收光谱法测定镍合金中痕量铋

镍基合金是航空工业的重要金属材料,合金中铋、铅、锡等易挥发元素的含量对合金材料性能影响很大[1,2].原子光谱法常被用于分析镍基合金中的痕量元素,如火焰原子吸收光谱法(FAAS)、氢化物发生-原子吸收(荧光)光谱法(HG-AAS/AFS) [3]、电感耦合等离子体-质谱法(ICP-MS).     

Preconcentration of palladium in a flow-through electrochemical cell for determination by graphite furnace atomic absorption spectrometry

An electrochemical preconcentration at a controlled potential on the electrode in a flow-through mode followed by graphite furnace atomic absorption spectrometric (GFAAS) detection is proposed for determination of trace amounts of palladium. After electrolysis the polarization of the electrodes was changed and deposited metal was dissolved electrochemically in the presence of an appropriate stripping reagent. Conditions for the electrodeposition, such as pH of the solutions, a deposition potential, dissolution potential and a composition of stripping solution were optimised. The graphite electrode (GE) and glassy carbon electrode (GCE) were tested for the palladium reduction process. The detection limit of 0.05 ng ml⁻¹ Pd (1 pg) was obtained after palladium preconcentration on the GCE and dissolution with 0.2 mol l⁻¹ thiourea in 0.1 mol l⁻¹ HCl followed by GFAAS detection. The method was applied for the determination of palladium in spiked tap water and road dust samples.     

In-situ concentration and determination of mercury by graphite furnace atomic absorption spectrometry with Pd-Rh as the chemical modifier

A method has been proposed for the determination of mercury by cold vapor generation graphite furnace atomic absorption spectrometry (CV-GFAAS) with Pd-Rh as coating and chemical modifier. The trapping efficiency for mercury with Pd-Rh was higher than with Pd alone. The characteristic mass of the method, which gives an integrated absorbance of 0.0044 s, was found to be 55 pg and the absolute detection limit (3 σ) of 37 pg was obtained with the proposed modifier. The method was successfully applied to the determination of mercury in standard reference water samples, wastewater samples and cosmetics with a recovery range of 95–104%. Received: 10 April 1998 / Revised: 20 August 1998 / Accepted: 23 September 1998     

In-situ concentration and determination of mercury by graphite furnace atomic absorption spectrometry with Pd-Rh as the chemical modifier

A method has been proposed for the determination of mercury by cold vapor generation graphite furnace atomic absorption spectrometry (CV-GFAAS) with Pd-Rh as coating and chemical modifier. The trapping efficiency for mercury with Pd-Rh was higher than with Pd alone. The characteristic mass of the method, which gives an integrated absorbance of 0.0044 s, was found to be 55 pg and the absolute detection limit (3 σ) of 37 pg was obtained with the proposed modifier. The method was successfully applied to the determination of mercury in standard reference water samples, wastewater samples and cosmetics with a recovery range of 95–104%. Received: 10 April 1998 / Revised: 20 August 1998 / Accepted: 23 September 1998     

Direct determination of germanium in botanical samples by graphite furnace atomic absorption spectrometry with palladium-zirconium as chemical modifier

A method has been described for the direct determination of trace levels of germanium by graphite furnace atomic absorption spectrometry (GFAAS) using chemical matrix modification technique. The stabilization and the pyrolysis temperatures for germanium were investigated with various chemical modifiers including palladium, palladium–magnesium, palladium–strontium and palladium–zirconium. The highest pyrolysis temperature and highest integrated absorbance were obtained using palladium–zirconium modifier, and the severe matrix interference from sulfate can be eliminated. The characteristic mass and absolute detection limit (3σ) of germanium were found to be 16 and 12 pg, respectively. The proposed method was applied to the determination of trace levels of germanium in botanical samples with a recovery range of 92–106%. The hydride generation atomic fluorescence spectrometric (HGAFS) method was employed to analyze the samples and the results agree well with those obtained by GFAAS. The contents of germanium in standard reference materials were determined and the results were in good agreement with the reference values.     

以8-羟基喹啉为化学改进剂石墨炉原子吸收光谱测定水和空气尘粒物中铬的研究

研究了8－羟基喹啉在石墨炉原子吸收光谱法（GFAAS）测定痕量铬中的化学改进作用及其主要影响因素。在优化实验条件下，8－羟基喹啉的存在能显著提高石墨炉原子吸收法测定铬的灵敏度。方法的检出限为0．20ng/mL，精密度为RSD＝2．6％（n＝8，c＝5ng/mL），本法已用于天然水和大气尘粒物中痕量铬的测定。     

Hollow-fiber liquid-liquid-solid micro-extraction of lead in soft drinks and determination by graphite furnace atomic absorption spectrometry

A novel hollow-fiber liquid-liquid-solid micro-extraction technique based on simultaneous liquid-liquid micro-extraction and solid phase micro-extraction using a polypropylene microporous membrane has been developed. The applicability of the proposed procedure was evaluated by extraction of Pb(II) from aqueous solutions and soft drinks. The parameters affecting the extraction efficiency were optimized using multivariate methodology, and the analytical features were established. Under optimized conditions, Pb(II) was concentrated for 20 min on three microporous membrane hollow fibers of 6 mm of length each, placed into 20 mL of sample containing 60 μL of toluene and ammonium O,O-diethyl dithiophosphate. The fibers were introduced directly into the graphite furnace as a solid sample, and the analyte was thermally desorbed from the fiber and atomized using ruthenium as a permanent modifier. A detection limit of 7 ng L⁻¹ Pb was obtained for soft drink samples and good repeatability was found for all samples. The enrichment factor varied between 22 and 66, depending if only one or all three hollow fibers were used for the determination of lead. The results suggest that the proposed procedure represents a simple and low-cost micro-extraction alternative rendering adequate limits of quantification for the determination of Pb(II) in soft drink samples.     

Determination of antimony in sediments and soils by slurry sampling graphite furnace atomic absorption spectrometry using a permanent chemical modifier

For comparison of action of mixed permanent modifiers Ir/Nb and Ir/W, the influence of the amounts of modifier components was studied and the atomic absorption pyrolysis and atomization curves were determined with different modifiers. The optimum amounts of modifier components were 30 μg Ir and 40 μg of Nb that were deposited onto the L'vov platform in advance to analytical measurements. The long-term performance of the Ir and Nb permanent modifiers was derived from the investigations by scanning electron microscopy and energy dispersive X-ray spectrometry. The soil and sediment slurries were prepared in 4% hydrofluoric acid and 6% suspension of polytetrafluoroethylene in order to remove the high concentration of silica during the pyrolysis step of 900 °C. The calibration was made by using aqueous standards. The analysis of certified reference materials confirmed the accuracy and reliability of the proposed analytical approach. The precision of Sb determination was characterized with less than 6% RSD.     

Method development for the determination of lead in wine using electrothermal atomic absorption spectrometry comparing platform and filter furnace atomizers and different chemical modifiers

A method has been developed for the determination of lead in wine by electrothermal atomic absorption spectrometry without any sample preparation and calibration against aqueous standards, using 7.5 μg Pd as a chemical modifier. The results obtained for seven wines using the proposed method and an acid digestion procedure did not show any significant difference using a Student's t-test. Atomization in a transversally heated filter atomizer (THFA) was compared with atomization in a conventional transversally heated platform furnace. The former provided a 2.6-fold higher sensitivity, improving the characteristic mass from 34 to 12 pg and a 1.6-fold better limit of detection (0.3 μg L⁻¹ compared to 0.5 μg L⁻¹) for aqueous solutions using the same injection volume of 20 μL. However, the average precision, expressed as the relative standard deviation for the determination of lead in wine under routine conditions was improved from 4.6% with platform atomization to 0.6% in the THFA. The lead content found in seven arbitrarily chosen white and red wines, five from Brazil, one from Chile and one from Spain, ranged from 6 to 60 μg L⁻¹ Pb with an average content of 11.4 μg L⁻¹ Pb for the wines from South America.     

石墨炉原子吸收光谱法测定锌基体物料中微量铊

采用B-HNO3-A溶解样品,硝酸钯作基体改进剂,通过优化仪器分析条件,灰化温度为500℃,原子化温度为1 800℃,成功实现了石墨炉原子吸收光谱法测定湿法冶炼锌基体物料锌精矿、锌焙砂、氧化锌、锌粉等物料中微量铊。方法对照实验结果与电感耦合等离子体质谱法(ICP-MS)测定值基本一致。方法的相对标准偏差(RSD,n≤8)为1.7%~7.8%,加标回收率为99%~103%。     

Cadmium and lead determination in foods by beam injection flame furnace atomic absorption spectrometry after ultrasound-assisted sample preparation

A simple method for cadmium and lead determination in foods by beam injection flame furnace atomic absorption spectrometry (BIFF-AAS) was proposed. Food slurries were prepared by transferring an exact amount of cryogenic-ground homogenized material (50-100 mg) to centrifuge tubes, followed by addition of 5 ml (up to 2.8 mol l⁻¹) nitric acid solution and sonication in an ultrasonic bath during 5-10 min. Thereafter, slurries were diluted with water to 10 ml, centrifuged during 5 min at 5400 rpm and 400 μl aliquot of the supernatant was analyzed by BIFF-AAS. The detection limits based on peak height measurements were 0.03 μg g⁻¹ Cd and 1.6 μg g⁻¹ Pb for 2% (m/v) slurry (200 mg/10 ml). For method validation, the certified reference materials Pig Kidney (BCR 186) and Rice Flour (NIES 10) were used. Quantitative cadmium and lead recoveries were obtained and no statistical differences were found at 95% level by applying the t-test.