Determination of organochlorine pesticides in sewage sludge by matrix solid-phase dispersion and gas chromatography-mass spectrometry

A method based on matrix solid-phase dispersion (MSPD) has been developed for the determination of 16 organochlorine pesticides (OCs) in sludge from municipal sewage plants. Samples of lyophilized sludge were blended with alumina, placed in small columns and OCs extracted with dichloromethane assisted by sonication. Purification of the extracts was accomplished by solid-phase extraction on C₁₈ columns and OCs were eluted with acetonitrile. Analyses were performed by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC–MS-SIM) using deuterated OCs as internal standards. The limits of detection were between 0.03 ng/g for 4,4′-DDE and 0.7 ng/g for endrin aldehyde.

Levels of OCs were determined in sewage sludge collected from 19 water treatment plants located in the province of Madrid (Spain). In all of the analyzed samples, aldrin was the compound most often found with a mean concentration of 76 ng/g. Endosulfan-I, -BHC, 4,4′-DDE and 4,4′-DDT were also present at high concentrations, with average values ranging from 32.3 to 74.3 ng/g. OCs were detected in all of the samples, with a total concentration ranging from 52 to 528 ng/g dry weight.     

Determination of suspected fragrance allergens in cosmetics by matrix solid-phase dispersion gas chromatography-mass spectrometry analysis

An effective low cost sample preparation methodology for the determination of regulated fragrance allergens in leave-on and rinse-off cosmetics has been developed applying, for the first time, matrix solid-phase dispersion (MSPD) to this kind of analytes and samples. The selection of the most suitable extraction conditions was made using statistical tools such as ANOVA, as well as a factorial multifactor experimental design. These studies were carried out using real cosmetic samples. In the final conditions, 0.5 of sample, previously mixed with 1g of anhydrous Na(2)SO(4), were blended with 2g of dispersive sorbent (Florisil), and the MSPD column was eluted with 5 mL of hexane/acetone (1:1). The extract was then analyzed by GC-MS without any further clean-up or concentration step. Accuracy, precision, linearity and detection limits (LODs) were evaluated to assess the performance of the proposed method. Quantitative recoveries (>75%) were obtained and RSD values were lower than 10% in all cases. The quantification limits were well below those set by the international cosmetic regulations, making this multi-component analytical method suitable for routine control. In addition, the MSPD method can be implemented in any laboratory at low cost since it does not require special equipment. Finally, a wide variety of cosmetic products were analyzed. All the samples contained several of the target cosmetic ingredients, with and average number of seven. The total fragrance allergen content was in general quite high, even in baby care products, with values close to or up to 1%, for several samples, although the actual European Cosmetic Regulation was fulfilled.     

固相微萃取-气相色谱法和气相色谱-质谱法测定茶叶中氟虫腈及其代谢物残留

基于固相微萃取-气相色谱(SPME-GC)建立了检测茶叶中氟虫腈及其代谢物(脱亚硫酰基氟虫腈、硫化氟虫腈、氟虫腈砜、酰胺氟虫腈)残留的分析方法。实验中采用85 μm聚丙烯酸酯(PA)萃取头,萃取温度为60 ℃,萃取缓冲体系的pH值为9。当添加水平为2～10 μg/kg时,回收率在71.2%～109.3%之间,相对标准偏差(RSD)在1.2%～7.1%之间。方法的检出限(LOD)和定量限(LOQ)分别在0.3～1.2 μg/kg和1.0～4.0 μg/kg之间。对所建立的方法采用气相色谱-质谱(GC-MS)进行确证,结果令人满意。本方法灵敏度、精密度和LOD均符合残留分析要求,具有快速、灵敏度高的特点,适合于茶叶中氟虫腈及其代谢物残留的痕量分析。     

气相色谱-质谱法测定猪肝中氯丙嗪残留量

猪肝中残留的氯丙嗪在碱性条件下经乙酸乙酯提取后,40℃水浴中旋转蒸发至近干,经乙腈溶解,正己烷脱脂,C18柱净化,以气相色谱-质谱选择86、233、272、318 4个碎片离子进行定性定量分析。氯丙嗪在10~200μg/L呈线性关系(R2为0.9998),3种不同添加浓度1.0、5.0和10μg/kg下氯丙嗪平均回收率分别为80.2%、90.7%、90.6%,相对标准偏差分别为8.6%、8.5%、5.9%,检出限(S/N=3)为1μg/kg,方法适用于猪肝等动物组织中氯丙嗪的测定。     

Method development for fingerprinting of biodiesel blends by solid-phase extraction and gas chromatography-mass spectrometry

A method based on the combination of solid-phase extraction (SPE) with gas chromatography-mass spectrometry (GC/MS) for detailed chemical fingerprinting of biodiesel/petrodiesel blends was developed in the present study. Forensic identification, commonly referred to as chemical fingerprinting, is based on the relative distributions of individual aliphatic hydrocarbons, aromatic hydrocarbons, fatty acid alkyl esters, and free sterols. Fractionation of fuel samples is optimized for the separation of fatty acid esters and free sterols from petroleum hydrocarbons into four fractions: aliphatic, aromatic, fatty acid ester, and polar components. The final recoveries of aliphatic and aromatic hydrocarbons were determined to be in the range of 65-103%, 73-105% for FAMEs, and 78-103% for free sterols in the polar fraction. Excellent separation with negligible crossover of components with different polarities between fractions was observed. Quantitative analysis of blend levels and individual chemical distribution were achieved. The method has great potential for the identification of biodiesel in diesel fuel blends and could form the basis of a method for characterization of biodiesel-contaminated environmental samples.     

Identification of flurbiprofen and its photoproducts in methanol by gas chromatography-mass spectrometry

A sample of 10 mM flurbiprofen in methanol (or ethanol) was photoirradiated with sixteen 8 W low-pressure quartz mercury lamps irradiated at 306 nm in a Panchum PR-2000 photochemical reactor. In total, four major photoproducts derived from each sample were observed from the HPLC chromatogram. The photoproducts were separated and their structures elucidated by various spectroscopic methods. Alternatively, using GC-MS, 11 major photoproducts were observed. A reaction scheme of flurbiprofen in methanol is proposed: the photochemical reaction routes occur mainly via esterification and decarboxylation, followed by oxidation with singlet oxygen to produce a ketone, alcohols and other derivatives.     

Determination of hydroxy-PCBs in urine by gas chromatography/mass spectrometry with solid-phase extraction and derivatization

A sensitive derivatization and extraction method is proposed for the determination of hydroxy-PCBs in urine. Phenolic hydroxyl groups of PCBs were allowed to react with five different reagents such as iodomethane, iodoethane, iodopropane, BSTFA and MTBSTFA. Propylated products at 100 °C for 30 min showed the best sensitivity with mass selective detector. Extraction recoveries and relative standard deviations of hydroxy-PCBs by SPE using C2 column were in the range of 78.0-112.3% and 2.5-9.6%, respectively. Instrumental detection limits for derivatized hydroxy-PCBs were in the range of 1-2 pg and were 10-1000 times more sensitive than those of non-derivatized hydroxy-PCBs. The correlation coefficients of the linear regression curves exceed 0.99, and the intra- and inter-day precisions were evaluated by RSDs within 10% at the concentrations of 0.4 and 4.0 ng/mL.     

Simple and automatic determination of aldehydes and acetone in water by headspace solid-phase microextraction and gas chromatography-mass spectrometry

We describe a simple and automatic method to determine nine aldehydes and acetone simultaneously in water. This method is based on derivatization with 2,2,2-trifluoroethylhydrazine (TFEH) and consecutive headspace-solid-phase microextraction and gas chromatography-mass spectrometry. Acetone-d(6) was used as the internal standard. Aldehydes and acetone in water reacted for 30 min at 40°C with TFEH in a headspace vial and the formed TFEH derivatives were simultaneously vaporized and adsorbed on polydimethylsiloxane-divinylbenzene. Under the established condition, the method detection limit was 0.1-0.5 μg/L in 4 mL water and the relative standard deviation was less than 13% at concentrations of 0.25 and 0.05 mg/L. This method was applied to determine aldehydes and acetone in 5 mineral water and 114 surface water samples. All mineral water samples had detectable levels of methanal (24.0-61.8 μg/L), ethanal (57.7-110.9 μg/L), propanal (11.5-11.7 μg/L), butanal, pentanal (3.3-3.4 μg/L) and nonanal (0.3-0.4 μg/L). Methanal and ethanal were also detected in concentration range of 2.7-117.2 and 1.2-11.9 μg/L, respectively, in surface water of 114 monitoring sites in Korea.     

Determination of microcystins in biological samples by matrix solid-phase dispersion and liquid chromatography-mass spectrometry

A method for the detection and quantification of the microcystins (MCs)-MC-LR, MC-RR and MC-YR-in biological samples by matrix solid-phase dispersion (MSPD) has been developed. The optimum extraction conditions were 500 mg of liver or kidney, C18 bonded silica as dispersant, and a mixture methanol-water (70:30) as eluent. The MCs were determined by liquid chromatography electrospray mass spectrometry (LC/ES/MS). Recoveries of biological extracts at three different spiked levels (1-10 mg kg(-1)) ranged from 40.5 to 87.0% in liver, and from 52.5 to 74.5 in kidney. R.S.D.s were < 15.6% and < 10.6%, respectively. The detection and quantification limits were 0.05 and 0.5 mg kg(-1), for all MCs. The method was applied to MCs detection in liver and kidney of rat previously injected i.p. with MC-LR. Results showed the presence of MC-LR in the liver of the animals injected with the highest dose.     

Matrix solid-phase dispersion extraction of organophosphorous pesticides from beeswax

Beeswax is a complex mixture of lipophilic compounds and other components such as aliphatic alcohols and carotenoids. Then, extraction and clean-up for pesticide analysis in beeswax is a challenge. In this work, a multiresidue method for the analysis of dichlorvos (DCV), diazinon, malathion, methyl parathion and coumaphos (CMF) in beeswax was developed. The proposed approach is based on matrix solid-phase dispersion extraction. The adsorbent for sample clean-up was studied and a simplex-centroid cubic statistical design was applied to evaluate pure solvents and their binary and ternary mixtures to elute the analytes. Finally, Florisil and ethyl acetate were chosen as solid support and eluting solvent, respectively. After extraction, pesticides were separated and detected by gas chromatography/mass spectrometry. The method achieved acceptable recoveries (70–85%; except for DCV, 24–38%) with relative standard deviations below 5%. The repeatability of the method was lower than 8% and interday variability was below 12%. The limit of detection (LOD) for the analytes varies between 0.2 and 2.6 µg?kg^?1 and limit of quantification from 0.93 to 8.8 µg?kg^?1. LOD reached for CMF was below the maximum residue limit allowed by the legislation of the United States and Canada.     

基质固相萃取-气相色谱电子捕获检测器同时测定大米中12种有机氯农药残留量

建立了大米中12种有机氯农药气相色谱-电子捕获检测器检测方法.采用基质固相分散(Matrix Solid Phase Disperse, MSPD)技术进行样品前处理, 用气相色谱-电子捕获检测器进行快速定性定量分析.基质固相分散集提取、过滤、净化于一步完成, 避免了样品均化、转溶、乳化、浓缩造成的待测农药组分的损失, 大大提高了方法的准确度和精密度.12种有机氯农药的添加回收率在83%～103%之间,相对标准偏差为2.2%～19%.     

Application of solid-phase microextraction and gas chromatography-mass spectrometry for the determination of chlorophenols in leather

This paper proposes a new analytical procedure based on the headspace solid‐phase microextraction (HS‐SPME) technique and gas chromatography‐selected ion monitoring‐mass spectrometry (GC‐SIM‐MS) for the determination of 16 phenols extracted from leather samples. The optimized conditions for the HS‐SPME were obtained through two experimental designs – a two‐level fractional factorial design followed by a central composite design – using the commercial SPME fiber polyacrylate 85 μm (PA). The best extraction conditions were as follows: 200 μL of derivatizing agent (acetic anhydride), 20 mL of saturated aqueous NaCl solution and extraction time and temperature of 50 min and 75°C, respectively. All optimized conditions were obtained with fixed leather sample mass (250 mg), vial volume (40 mL) and phosphate buffer pH (12) and concentration (50 mmol/L). Detection limits ranging from 0.03 to 0.20 ng/g, and relative standard deviation (RSD) lower than 10.23% (n=6) for a concentration of 800 ng/g (chlorophenols) and 1325 ng/g (2‐phenylphenol) in the splitless mode were obtained. The recovery was studied at three concentration levels by adding different amounts of phenols to the leather sample and excellent recoveries ranging from 90.0 to 107.2% were obtained. The validated method was shown to be suitable for the quantification of phenols in leather samples, as it is simple, relatively fast and sensitive.     

Determination of 5,5-diphenylhydantoin and its major metabolites in biological specimens by gas chromatography and selected ion-monitoring

Summary A specific and sensitive procedure for simultaneous determination of 5,5-diphenylhydantoin, 5-(4-hydroxyphenyl)-5-phenylhydantoin, 5-(3,4-dihydroxyphenyl)-5-phenylhydantoin and 5-(3-methoxy-4-hydroxyphenyl)-5-phenylhydantoin in biological specimens is described. The method involves formation of butylated or trideuteromethylated derivatives of the drug and its metabolites and analysis by gas chromatography. The lower detectable concentration of these compounds per ml of body fluids or g of wet tissue is either 1 g or 20 ng, depending on the type of detector used, flame ionization or selected-ion monitoring. Data on the urinary elimination of 5,5-diphenylhydantoin and hydroxylated metabolites in male rats following a single intraperitoneal injection of the drug (25 mg/kg) are also reported.     

Determination of ketamine and metabolites in urine by liquid chromatography-mass spectrometry

We have developed an analytical method by using liquid chromatography-mass spectrometry (LC-MS) to determine ketamine and its metabolites in urine. The ionization efficiency between two ionization modes (ESI and APCI) of LC-MS was compared to each other. An easy and simple sample preparation of urine samples was made by passing samples through a 0.22 μm PVDF syringe filter. The results indicated that the ionization efficiency of positive APCI mode is better than positive ESI mode for determination of trace ketamines. A wide linearity range of the research is from 5 to 250 ng mL⁻¹ and the detection limits for ketamine, norketamine and dehydronorketamine were 0.95, 0.48 and 0.33 ng mL⁻¹, respectively. The proposed method was tested by analyzing ketamine and metabolites in the urines of volunteers. The concentrations of ketamine, norketamine and dehydronorketamine are ranged of 5.4-131.0, 12.5-74.1 and 22.8-278.9 ng mL⁻¹, respectively and the ketamines concentration profiles in human urine were also determined. The results demonstrate the suitability of liquid chromatography-mass spectrometry approach to analyze trace amount of ketamine and its metabolites in urine.     

Combined solid-phase extraction and gas chromatography-mass spectrometry used for determination of chloropropanols in water

A sensitive and rapid derivatization method for the simultaneous determination of 1,3-dichloro-2-propanol (1,3-DCP) and 3-chloropropane-1,2-diol (3-MCPD) in water samples has been developed. The aim was to research the optimal conditions of the derivatization process for two selected reagents. A central composite design was used to determine the influence of derivatization time, derivatization temperature and reagent volume. A global desirability function was applied for multi-response optimization. The analysis was performed by gas chromatography-mass spectrometry. During the optimization of the extraction procedure, four different types of solid-phase extraction (SPE) columns were tested. It was demonstrated that the Oasis HLB cartridge produced the best recoveries of the target analytes. The pH value and the salinity were investigated using a Doehlert design. The best results for the SPE of both analytes were obtained with 1.5 g of NaCl and pH 6. The proposed method provides high sensitivity, good linearity (R(2)≥0.999) and repeatability (relative standard deviations % between 2.9 and 3.4%). Limits of detection and quantification were in the range of 1.4-11.2 ng/mL and 4.8-34.5 ng/mL, respectively. Recoveries obtained for water samples were ca. 100% for 1,3-DCP and 3-MCPD. The method has been successfully applied to the analysis of different samples including commercially bottled water, an influent and effluent sewage.     

基质分散固相萃取-超高效液相色谱-串联质谱法测定蔬菜风险监测中的9种农药残留

建立了基质分散固相萃取-超高效液相色谱-串联质谱测定蔬菜中多菌灵、氧乐果、克百威、涕灭威、毒死蜱、甲胺磷、甲拌磷、对硫磷、甲基对硫磷9种农药残留的方法。蔬菜通过乙腈提取、盐析分配、基质分散固相萃取净化后,采用Waters BEH C18柱(100 mm×2.1 mm, 1.7 μm),以乙腈和0.1%甲酸水溶液作为流动相,梯度洗脱,电喷雾电离正离子(ESI⁺)、多反应监测(MRM)模式测定,基质匹配标准溶液工作曲线法定量。该方法的检出限为0.8~4.0 μg/kg,回收率为72.8%~117.4%。50批蔬菜样品中毒死蜱、多菌灵和氧乐果残留的检出率分别为42.0%、14.0%和2.0%,毒死蜱超标率为8.0%,其他农药未检出。该法可同时测定食品风险监测中蔬菜的农药残留,具有操作方便、准确率高、重复性好等优点,可满足蔬菜中农药残留的检测要求。     

Determination of carbamate residues in fruits and vegetables by matrix solid-phase dispersion and liquid chromatography-mass spectrometry

Thirteen carbamates were analysed in orange, grape, onion and tomatoes by matrix solid-phase dispersion (MSPD) followed by liquid chromatography-mass spectrometry (LC-MS). Electrospray (ES) and atmospheric pressure chemical ionisation (APCI) were compared and both gave similar results in terms of sensitivity and structural information because at 20 V fragmentor voltages the fragmentation is minimal. The efficiency of different solid-phases (C18, C8, cyano, amine and phenyl) for the MSPD was compared. Mean recoveries using C8 varied from 64 to 106% with relative standard deviations of 5-15% in the concentration range of 0.01-10 mg kg(-1). Matrix constituents did not interfere significantly with the ionisation process of carbamates. The limits of detection were typically in the 0.001-0.01 mg kg(-1) range, which were between 10 and 100 times lower than the maximum residue levels (MRLs) established by the European Union (EU). The method was applied to residue detection in fruit and vegetable samples taken from Valencian markets, in which carbamates were detected at low concentrations.     

Tentative identification of new metabolites of epimedin C by liquid chromatography-mass spectrometry

Epimedin C is one of the major bioactive constituents of Herba Epimedii. The aim of this study is to characterize and elucidate the structure of metabolites in the rat after administration of epimedin C. Metabolite identification was performed using a predictive multiple reaction monitoring-information dependent acquisition-enhanced product ion (pMRM-IDA-EPI) scan in positive ion mode on a hybrid triple quadrupole-linear ion trap mass spectrometer. A total of 18 metabolites were characterized by the changes in their protonated molecular masses, their MS/MS spectrum and their retention times compared with those of the parent drug. The results reveal possible metabolite profiles of epimedin C in rats; the metabolic pathways including hydrolysis, hydroxylation, dehydrogenation, demethylation and conjugation with glucuronic acid and different sugars were observed. This study provides a practical approach for rapidly identifying complicated metabolites, a methodology that could be widely applied for the structural characterization of metabolites of other compounds.     

Headspace solid-phase microextraction with on-fiber derivatization for the determination of aldehydes in algae by gas chromatography-mass spectrometry

A simple, fast, sensitive and cost-effective method based on headspace solid-phase microextraction (HS-SPME) with on-fiber derivatization coupled with gas chromatography-mass spectrometry was developed for the determination of six typical aldehydes, 2E-hexenal, heptanal, 2E-heptenal, 2E,4E-heptadienal, 2E-decenal and 2E,4E-decadienal in laboratory algae cultures. As derivatization reagent, O-2,3,4,5,6-(pentafluorobenzyl) hydroxylamine hydrochloride, was loaded onto the poly(dimethylsiloxane)/divinylbenzene fiber for aldehydes on-fiber derivatization prior to HS-SPME. Various influence factors of extraction efficiency were systematically investigated. Under optimized extraction conditions, excellent method performances for all the six aldehydes were attained, such as satisfactory extraction recoveries ranging from 67.1 to 117%, with the precision (relative standard deviation) within 5.3-11.1%, and low detection limits in the range of 0.026-0.044 μg/L. The validated method was successfully applied for the analysis of the aldehydes in two diatoms (Skeletonema costatum and Chaetoceros muelleri), two pyrrophytas (Prorocentrum micans and Scrippsiella trochoidea) and Calanus sinicus eggs (feeding on the two diatoms above).