热声制冷机板叠内流动与换热的数值分析

本文采用基于压力修正算法的可压缩交变流动程序,采用适体坐标生成网格,AUSM 格式离散N-S方程和能量方程,计算了二维基本型热声制冷机板叠内的流动与换热情况,探讨了板叠附近的温度随时间的变化,分析了周期时均能量.由模拟结果可以看出,在气体冷端,能量由气体进入板叠,时均能量为正,在气体热端,能量由板叠进入气体,时均能量为负,板叠热端的时均能量稍大于板叠冷端的时均能量,板叠产生了冷量.但与输入功相比,板叠产生的冷量较小,因此系统的内能增加,气体冷端的温度增加.并且随着板叠的厚度的增加,板叠冷热端温差先增大后减小,并存在最佳板叠厚度使得冷热端的温差达到最大.     

非平行板叠驻波型热声发动机热力性能研究

热声发动机板叠两端存在较大的温度梯度,导致沿板叠轴向的热渗透深度出现严重的不均一性,影响到热声转换效应的发挥。本文提出了板叠结构形式与温度梯度相一致的结构设计理念,并构建了非平行板叠结构的驻波型热声发动机数理模型。针对不同板叠锥角热声发动机的热力性能展开了深入研究和对比分析,得出板叠锥角对热声发动机频率、压比、压力振幅和体积流率等热力参数的影响关系。结果表明:与平行板叠结构相比,当选取合适锥角时,渐缩和渐扩式板叠结构均可提高热声系统的性能,在1°和-2.81°时系统的最大声功流分别提高了103.9%和88.8%。研究结果为进一步改善热声热机性能提供理论支撑。     

惯性项对回热器交变流动阻力特性影响分析

基于流体动量方程从机理上分析了交变流动和稳定流动存在差别的根本原因。以动态参数测量为基础,在运行频率30～60 Hz,最大热端压比1.3,充气压力1.0～3.0 MPa,等温条件下,首次定量化研究了惯性项对小管径(φ8 mm)、高目数丝网(300～500目)填充回热器交变流动阻力特性的影响。综合频率和压比对交变流动回热器阻力特性的影响,可以得出结论:在本实验条件下,回热器交变流动系统中的惯性力与压力相比始终是个小量,从流动角度来说,可以对回热器中气体交变流动作准稳态处理。     

热声交变流动中浮力效应理论分析

热声交变流动是热声热机的工作基础,研究交变流动机理有助于人们认识热声热机的工作过程。鉴于前人的理论分析一般没有考虑浮力效应的影响,本文从流体热动力学的角度研究了浮力对流与热声交变流动的耦合规律。基于线性理论方法,给出了考虑浮力项和热对流Rayleigh数的热声线性理论模型,分析了浮力效应对平行交变流动的影响,发现热对流...     

热声制冷机的一种非线性模型研究

为研究热声制冷机内部的非线性过程,发展了一种可考虑管道截面积变化的时域准一维非线性热声模型,其主控方程由可压流基本控制方程经截面平均的数学处理推导得出,数值求解采用具有频散保持特性的高精度计算格式。采用该模型分别针对活塞、扬声器和热声发动机这三种不同驱动源,将驱动源和热声制冷机进行整体求解,模拟了热声制冷板叠两端温度差在气体微团吸放热的循环过程中逐渐增大的整个过程,预测了谐振管内部驻波的非线性畸变。进而研究了平均工作压力、板叠材料、板叠位置以及扬声器形状等参数的选取对于热声制冷机制冷效果的影响。     

热声压力波放大器的湍流模型及实验验证

热声压力波放大器是一种利用声学特性将压力波幅值进行放大的一种装置,它主要用来连接热声发动机和其驱动的制冷机,增大制冷机的驱动压比.由于声学压力波放大器内的压力幅值通常较大,流动速度也非常大,所以用线性热声理论难以对其进行准确的计算.本文通过对线性热声理论进行修正,获得了热声压力波放大器内湍流流动的修正方法,并对该修正方法进行了实验验证.研究结果表明,通过修正后的理论模型可以对热声压力波放大器进行较为准确的计算.该计算模型预计在其它的一些交变流动系统中也具有一定的适用性.     

热声发动机的优化计算设计

把改进的12-Bit格子气模型用于复杂边界的热声发动机的模拟研究,成功模拟了带共振腔的驻波管中热声振荡演化过程。对热声板叠的长度、热声板叠在共振管中的位置以及共振腔的几何大小对热声振荡振幅的影响进行了数值计算。计算结果显示,当共振腔与细管的宽度比为2.2,板叠位置相对于细管长为0.34时,驻波管中热声振荡振幅达到最大。共振腔尺寸的研究,对于热声发动机性能的的优化设计有指导意义。     

驻波热声冷却机的研究

与压缩机制冷相比,热声制冷结构简单、可靠性高和使用寿命长。本文在正常室温(20℃)和室压(1个大气压)的工作环境下以空气为声学介质来探讨热声制冷机的设计及热声制冷效果的影响因素,并制作样机进行实验研究。研究发现:板叠长度和中心位置对热声转换效率影响较大,其数值需要理论与实验相结合来确定;以空气为声学工质,在正常室温、室压下的热声制冷机,用50W的供电驱动、90 Hz工作时可实现冷热端37℃的温差。     

工作压力对热声驱动阻容负载性能影响的实验研究

进行了热声发动机驱动阻容负载的实验研究;讨论了工作压力对热声驱动阻容负载性能的影响。随着平均工作压力的增大,负载入口处压力振幅和输出的声功率都明显增大,同时板叠热端温度有较大幅度下降,有利于低品位热源的利用和提高系统相对卡诺效率。     

气体工质对气液热声发动机性能的影响

本文针对一台气液耦合振动热声发动机,以1．5kg的水作为液柱,以氮气、氦气、氩气和二氧化碳分别作为气体工质,在2．0MPa平均工作压力下,实验对比了不同气体工质对谐振频率、压力振幅和板叠热端温度等系统性能参数的影响。实验结果表明,在相同加热功率下,采用氩气的系统获得的压力振幅最大;而在相同板叠热端温度下,以二氧化碳为气...     

Vortex dynamics of a trapezoidal bluff body placed inside a circular pipe

The influence of Reynolds number and blockage ratio on the vortex dynamics of a trapezoidal bluff body placed inside a circular pipe is studied experimentally and numerically. Low aspect ratio, high blockage ratio, curved end conditions (junction of pipe and bluff body), axisymmetric upstream flow with shear and turbulence are some of the intrinsic features of this class of bluff body flows which have been scarcely addressed in the literature. A large range (200:200,000) of Reynolds number (Re_D) is covered in this study, encompassing all the three pipe flow regimes (laminar, transition and turbulent). Four different flow regimes are defined based on the distinct features of Strouhal number (St)–Re_D relation: steady, laminar irregular, transition and turbulent. The wake in the steady regime is stationary with no oscillations in the shear layer. The laminar regime is termed as irregular owing to irregular vortex shedding. The vortex shedding in this regime is observed to be symmetric. The emergence of separation bubble downstream of the bluff body on either side is another interesting feature of this regime, which is further observed to be symmetric. Two pairs of mean streamwise vortices are noticed in the near-wake regime, which are termed as reverse dipole-type wake topology. Beyond the irregular laminar regime, the Strouhal number falls gradually and vortex shedding becomes more periodic. This regime is named transition and occurs close to the Reynolds number at which transition to turbulence takes place in a fully developed pipe. The turbulent regime is characterised by a nearly constant Strouhal number. Typical Karman-type vortex shedding is noticed in this regime. The convection velocity, wake width formation length and irrecoverable pressure loss are quantified to highlight the influence of blockage ratio. These results will be useful to develop basic understanding of vortex dynamics of confined bluff body flow for several practical applications.     

冷却孔附近三维流动的结构

本文简略综述了横流中射流研究的局部结构,并且采用数值模拟的方法,研究在给定横向流速和不同吹风比(0．5、1．0和1．5)条件下,圆形垂直射流孔附近区域三维定常流动的流场,以揭示局部流场的复杂涡系结构和形成机理。     

Visualization of three-dimensional flow structures in the wake of an inclined circular cylinder

In the previous measurements of the aerodynamic sound generated from an inclined circular cylinder, it is reported that the sound pressure level (SPL) changes with the aspect ratio and the inclined angle. Therefore, we have investigated the changes in the vortex structure of the wake considered as one of the causes of the SPL variation. Using the low-noise wind tunnel, the velocity fluctuation in the wake is measured to obtain the correlation length. Moreover, the flow visualization is performed with a hydrogen bubble method and a numerical analysis method in order to clarify how the wake structure changes by variations of aspect ratio and inclined angle. As a result of this investigation, it is shown that the spanwise structure of Karman’s vortex is highly influenced by the interference of Karman’s vortex with the bottom endplate, and that the influence on the spanwise structure in the wake becomes greater as the aspect ratio decreases and the inclined angle increases.     

High-definition PIV analysis on vortex shedding in the cylinder wake

A high-definition analysis based on flow topology is made on the vortex motions under natural and lock-on conditions in the near-wake region of a circular cylinder, where two-dimensional flow fields in the wake-transition regime are measured by a time-resolved PIV system. The Reynolds stress distributions are examined in view of the mean separation streamline and the trajectory ofthe vortex center. It is shown that, by the lock-on, the Reynolds stresses become stronger and their dispositions match well with the shortened wake bubble, indicating perfect synchronization of shedding to the oscillatory forcing flow in the near field, which causes increased lift and drag forces.     

叶顶端翼提升主动襟翼叶型气动性能的数值研究

本文在振荡来流条件下,数值模拟叶顶端翼对加装主动Gurney襟翼的垂直轴风力机叶片非定常气动特性的影响。采用NACA0015翼型的直叶片,并在尾缘前6%弦长位置安装主动襟翼。在最大出力工况(折合频率为0.1)下,对比原型叶片,加装主动襟翼叶片的切向力系数提高了4.47%,安装有叶顶端翼的主动襟翼叶片的切向力系数提高21.18%。通过比较叶片端部涡结构分布,发现叶顶端翼不仅阻止了叶片压力面及吸力面的叶梢涡分支在尾缘处汇合,同时也隔断了主动襟翼产生的角涡与叶梢涡的融合,有效的降低了叶片端部损失,提升了风力机的整体性能。     

Horseshoe vortices in inhomogeneous flows

The formation of a horseshoe-shaped vortex from an initial straight cylindrical vortex occurring in the viscous layer of a retarding fluid flow in a channel with a nonuniform cross section is studied experimentally. The spatial bends of the vortex filament and the effect of the ambient fluid pressure first form an arch with supports at the bottom of the channel, then a horseshoe-shaped vortex, and finally a circular vortex with the destruction of the supports.     

Interaction of induced sound with flow past a square leading edged plate in a duct

The interaction of resonant sounds with the flow past a thick, blunt, flat plate in a rigid walled square duct has been examined. Sound pressure levels of up to 146 dB (re 20 μPa) have been recorded. It has been established that the resonant sound can initially be excited at a harmonic of the normal vortex shedding frequency. In some cases, the sound “feeds back” on the vortex shedding process causing a step change in the shedding frequency, increasing the Strouhal number for the plate by up to twice the normal value. This excited vortex shedding and associated resonances can be suppressed by locating the plate at incidence to the air flow direction. Complex duct modes can be generated by the vortex shedding resulting in different regions of the plate shedding at different Strouhal numbers.     

涡发生器对高超声速轴对称进气道外部流动的影响

采用三维CFD黏性模拟考察涡发生器对高超声速轴对称进气道外部流动的影响.针对前缘钝化半径0.8 mm和3.2 mm的轴对称进气道外部流场,以涡发生器高度与当地位移边界层厚度比值为影响参数,考察流场结构与性能参数的影响规律.结果表明,涡发生器产生的干扰波系使得前缘激波向外偏移,下游近壁面流动与主流区出现明显的交换,下游流动出现明显的展向非均匀性.涡发生器对流动的影响沿流向逐渐减弱.在气流压缩性能方面,涡发生器下游压比、动压比沿流向开始增大,随后逐渐恢复到无涡发生器工况;Mach数、总压恢复系数开始降低,随后逐渐向无涡发生器工况趋近.涡发生器高度与当地位移边界层厚度的比值h可作为衡量其影响的重要参数.当h≤1.5时,进气道流场结构、性能参数的变化几乎可忽略,h≤3.0时进气道入口处性能参数几乎能够恢复到无涡发生器工况.      

Global visualization and quantification of compressible vortex loops

The physics of compressible vortex loops generated due to the rolling up of the shear layer upon the diffraction of a shock wave from a shock tube is far from being understood, especially when shock-vortex interactions are involved. This is mainly due to the lack of global quantitative data available which characterizes the flow. The present study involves the usage of the PIV technique to characterize the velocity and vorticity of compressible vortex loops formed at incident shock Mach numbers ofM=1.54 and1.66. Another perk of the PIV technique over purely qualitative methods, which has been demonstrated in the current study, is that at the same time the results also provide a clear image of the various flow features. Techniques such as schlieren and shadowgraph rely on density gradients present in the flow and fail to capture regions of the flow influenced by the primary flow structure which would have relatively lower pressure and density. Various vortex loops, namely, square, elliptic and circular, were generated using different shape adaptors fitted to the end of the shock tube. The formation of a coaxial vortex loop with opposite circulation along with the generation of a third stronger vortex loop ahead of the primary with same circulation direction are of the interesting findings of the current study.     

小流量涡流管特性的实验研究

本文用实验方法研究了小流量涡流管制冷的特性。实验中分别对入口压力和工质等因素对涡流管特性的影响进 行研究。在实验中发现了涡流管冷端制热和热端制冷的反常现象,并对其进行了解释。