A novel solution-based self-assembly approach to preparing ultralong titanyl phthalocyanine sub-micron wires

Ultralong titanyl phthalocyanine （TiOPc） sub-micron wires have been synthesized by a novel solution-based self- assembly method. By using different solvents, changing the mass concentration and the solvent vapor pressure, the length and the shape of the wires can be adjusted. The mixed-phase properties of the TiOPc sub-micron wires were investigated by the ultraviolet-visible （UV-vis） absorption spectrum and X-ray diffraction. Organic transistors based on these wires were studied, which show the typical p-channel characteristics.     

Identification of pore size in porous SiO2 thin film by positron annihilation

Positron annihilation lifetime and Doppler broadening of annihilation line techniques have been used to obtain information about the small pore structure and size of porous SiO2 thin film produced by sputtered Al-Si thin film and etched Al-Si thin film. The film is prepared by an Al/Si 75：25 at.-% （A175Si25） target with the radiofrequency （RF） power of 66 W at room temperature. A 5 wt.-% phosphoric acid solution is used to etch the Al cylinders. All the A1 cylinders dissolved in the solution after 15 h at room temperature, and the sample is subsequently rinsed in pure water. In this way, the porous SiO2 on the Si substrate is produced. From our results, the values of all lifetime components in the spectra of Al-Si thin film are less than 1 ns, but the value of one of the lifetime components in the spectra of porous SiO2 thin film is τ = 7.80 ns. With these values of lifetime, RTE （Rectangular Pore Extension） model has been used to analyze the pore size.     

Synthesis of ZrSiN composite films using a plasma focus device

ZrSiN thin films are synthesized by using plasma focus through various numbers of focus shots （10, 20, and 30）, with samples placed at 9 cm away from the tip of the anode. Crystal structures, surface morphologies, and elemental compositions of ZrSiN films are characterized by an X-ray diffractometer （XRD） and scanning electron microscope （SEM） attached with energy dispersive X-ray spectroscopy （EDS）. XRD patterns confirm the formations of polycrystalline ZrSiN films. Crystallinity of nitride increases with the increase of focus shot number. The average crystallite size of zirconium nitride increases from 27 ± 3 nm to 73±8 nm and microstrain decreases from 2.28 to 1.0 with the increase of the focus shot number. SEM results exhibit the formations of granular and oval-shaped microstructures, depending on the number of focus shots. EDS results confirm the presences of silicon, zirconium, nitrogen, and oxygen in the composite films. The content values of Zr and N in the composite films increase with the increase of the focus shot number.     

Properties of transistor based C60 thin film on polystyrene

This paper reports that the n-type organic thin-fihn transistors have been fabricated by using C60 as the active layer and polystyrene as the dielectric. The properties of insulator and the growth characteristic of C60 film were carefully investigated. By choosing different source/drain electrodes, a device with good performance can be obtained. The highest electron field effect mobility about 1.15 cm2/（V. s） could reach when Barium was introduced as electrodes. Moreover, the C60 transistor shows a negligible ＇hysteresis effect＇ contributed to the hydroxyl-free of insulator. The result suggests that polymer dielectrics are promising in applications among n-type organic transistors.     

Characterization of zirconium thin films deposited by pulsed laser deposition

Zirconium(Zr) thin films deposited on Si(100) by pulsed laser deposition(PLD) at different pulse repetition rates are investigated. The deposited Zr films exhibit a polycrystalline structure, and the X-ray diffraction(XRD) patterns of the films show the α Zr phase. Due to the morphology variation of the target and the laser–plasma interaction, the deposition rate significantly decreases from 0.0431 /pulse at 2 Hz to 0.0189 /pulse at 20 Hz. The presence of droplets on the surface of the deposited film, which is one of the main disadvantages of the PLD, is observed at various pulse repetition rates. Statistical results show that the dimension and the density of the droplets increase with an increasing pulse repetition rate. We find that the source of droplets is the liquid layer formed under the target surface. The dense nanoparticles covered on the film surface are observed through atomic force microscopy(AFM). The root mean square(RMS) roughness caused by valleys and islands on the film surface initially increases and then decreases with the increasing pulse repetition rate.The results of our investigation will be useful to optimize the synthesis conditions of the Zr films.     

Preparation and modification of VO_2 thin film on R-sapphire substrate by rapid thermal process

The VO2 thin film with high performance of metal-insulator transition （MIT） is prepared on R-sapphire substrate for the first time by magnetron sputtering with rapid thermal process （RTP）. The electrical characteristic and THz transmittance of MIT in VO2 film are studied by four-point probe method and THz time domain spectrum （THz-TDS）. X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, atomic force microscopy （AFM）, and search engine marketing （SEM） are employed to analyze the crystalline structure, valence state, surface morphology of the film. Results indicate that the properties of VO2 film which is oxidized from the metal vanadium film in oxygen atmosphere are improved with a follow- up RTP modification in nitrogen atmosphere. The crystallization and components of VO2 film are improved and the film becomes compact and uniform. A better phase transition performance is shown that the resistance changes nearly 3 orders of magnitude with a 2-~C hysteresis width and the THz transmittances are reduced by 64% and 60% in thermal and optical excitation respectively.     

Magnetic behaviors of cerium oxide-based thin films deposited using electrochemical method

Zn and Co multi-doped CeO2 thin films have been prepared using an anodic electrochemical method. The structures and magnetic behaviors are characterized by several techniques, in which the oxygen states in the lattice and the absorptive oxygen bonds at the surface are carefully examined. The absorptive oxygen bond is about 50% of the total oxygen bond by using a semi-quantitative method. The value of actual stoichiometry δ is close to 2. The experimental results indicate that the thin films are of a cerium oxide-based solid solution with few oxygen vacancies in the lattice and many absorptive oxygen bonds at the surface. Week ferromagnetic behaviors were evidenced by observed M–H hysteresis loops at room temperature. Furthermore, an evidence of relative ferromagnetic contributions was revealed by the temperature dependence of magnetization. It is believed that the ferromagnetic contributions exhibited in the M–H loops originate from the absorptive oxygen on the surface rather than the oxygen vacancies in the lattice.     

The design and preparation of a Fabry-Perot polarizing filter

A novel single-cavity narrowband Fabry-Perot （FP） polarizing filter at normal incidence, constructed from a sandwich structure with sculptured anisotropic space layer and symmetric isotropic HR mirrors, is designed and prepared. The optical performances of transmittance, phase shift, central wavelength, and bandwidth for two polarized states are analyzed with the characteristic matrix. The numerical studies accord reasonably well with the experimental results. It is demonstrated that the polarization state of the electromagnetic wave and phase shift can be modulated by employing an anisotropic space layer in the polarizing beam splitter system. The birefringence of the anisotropic space layer provides a sophisticated phase modulation by varying the incidence angles over a broad range to have a wide-angle phase shift.     

Structural properties of a-SiO_x:H films studied by an improved infrared-transmission analysis method

An improved method of fitting point-by-point is proposed to determine the absorption coefficient from infrared(IR)transmittance. With no necessity of empirical correction factors, the absorption coefficient can be accurately determined for the films with thin thicknesses. Based on this method, the structural properties of the hydrogenated amorphous silicon oxide materials(a-SiOx:H) are investigated. The oxygen-concentration-dependent variation of the Si–O–Si and the Si–H related modes in a-SiOx:H materials is discussed in detail.     

L lo FePt thin films with [001] crystalline growth fabricated by ZnO addition and rapid thermal annealing

FePt films with a high degree of order S of the L10 structure （S 〉 0.90） and well defined [001] crystalline growth perpendicular to the film plane are fabricated on thermally oxidized Si substrates by the addition of ZnO and a successive rapid thermal annealing （RTA） process. The optimum condition to prepare high-ordering L10 FePtZnO films is 20 vol% ZnO addition and 450 ℃ annealing. The effect of the ZnO additive on the ordering process of the L10 FePtZnO films is discussed. In the annealing process, Zn atoms move to the film surface and evaporate. The motion of the Zn atoms accelerates the intergrain exchange and decreases the ordering temperature.     

Effects of annealing rate and morphology of sol–gel derived ZnO on the performance of inverted polymer solar cells

The effects of annealing rate and morphology of sol–gel derived zinc oxide(ZnO)thin films on the performance of inverted polymer solar cells(IPSCs)are investigated.ZnO films with different morphologies are prepared at different annealing rates and used as the electron transport layers in IPSCs.The undulating morphologies of ZnO films fabricated at annealing rates of 10 C/min and 3 C/min each possess a rougher surface than that of the ZnO film fabricated at a fast annealing rate of 50 C/min.The ZnO films are characterized by atomic force microscopy(AFM),optical transmittance measurements,and simulation.The results indicate that the ZnO film formed at 3 C/min possesses a good-quality contact area with the active layer.Combined with a moderate light-scattering,the resulting device shows a 16%improvement in power conversion efficiency compared with that of the rapidly annealed ZnO film device.     

Homogeneity analysis of sculptured thin films deposited in symmetric style through glancing angle deposition technique

The symmetric deposition technique is often used to improve the uniformity of sculptured thin film （STF）. In this paper, optical properties of STF with the columnar angles 4-/3 are analyzed theoretically, based on the characteristic matrix method for extraordinary waves. Then, the transmittances of uniformity monolayer and bilayer STF in symmetrical style are calculated to show the effect of the bilayer structure on the optical properties of STF. The inhomogeneity of STF is involved in analyzing the differences in transmittance and phase retardation between monolayer and bilayer STF deposited in symmetric style. The results show that optical homogeneity of STF can be improved by depositing in symmetric style at the normal incidence, but it is not the same case as the oblique incidence.     

Enhancement-mode A1GaN/GaN high electronic mobility transistors with thin barrier＊

An enhancement-mode （E-mode） A1GaN/GaN high electron mobility transistor （HEMTs） was fabricated with 15-nm A1GaN barrier layer. E-mode operation was achieved by using fluorine plasma treatment and post-gate rapid thermal annealing. The thin barrier depletion-HEMTs with a threshold voltage typically around -1.7 V, which is higher than that of the 22-nm barrier depletion-mode HEMTs （-3.5 V）. Therefore, the thin barrier is emerging as an excellent candidate to realize the enhancement-mode operation. With 0.6-tim gate length, the devices treated by fluorine plasma for 150-W RF power at 150 s exhibited a threshold voltage of 1.3 V. The maximum drain current and maximum transconductance are 300 mA/mm, and 177 mS/ram, respectively. Compared with the 22-nm barrier E-mode devices, VT of the thin barrier HEMTs is much more stable under the gate step-stress,     

Homogeneous interface-type resistance switching in Au/La0.67Ca0.33MnO3/SrTiO3/F:SnO2 heterojunction memories

La0.67Ca0.33MnO3 thin films are fabricated on fluorine-doped tin oxide conducting glass substrates by a pulsed laser deposition technique with SrTiO3 used as a buffer layer. The current-voltage characteristics of the heterojunetions exhibit an asymmetric and resistance switching behaviour. A homogeneous interface-type conduction mechanism is also reported using impedance spectroscopy. The spatial homogeneity of the charge carrier distribution leads to field- induced potential-barrier change at the Au-La0.67Ca0.33MnO3 interface and a concomitant resistance switching effect. The ratio of the high resistance state to the low resistance state is found to be as high as 1.3 x 10^4% by simulating the AC electric field. This colossal resistance switching effect will greatly improve the signal-to-noise ratio in nonvolatile memory applications.     

Multiferroic properties of sol-gel derived Bi5Fe1-xCoxTi3O15 thin films

Co-doped Bi 5 FeTi 3 O 15 thin films (BFCT-x,Bi 5 Fe 1-x Co x Ti 3 O 15) were prepared using a sol-gel technique.XRD patterns confirm their single phase Aurivillius structure,and the corresponding powder Rietveld analysis indicates the change of space group around x=0.12.The magnetic hysteresis loops are obtained and ferromagnetism is therefore confirmed in BFCT-x thin films.The remanent magnetization (M r) first increases and reaches the maximum value of 0.42 emu/cm 3 at x=0.12 due to the possible Fe 3+-O-Co 3+ ferromagnetic coupling.When x=0.25,the M r increases again because of the dominant Fe 3+-O-Co 3+ ferromagnetic coupling.The remanent polarization (2P r) of BFCT-0.25 was measured to be as high as 62 μC/cm 2,a 75% increase when compared with the non-doped BFCT-0 films.The 2P r remains almost unchanged after being subjected to 5.2 × 10 9 read/write cycles.Greatly enhanced ferroelectric properties are considered to be associated with decreased leakage current density.     

Electrical and optical properties of Sb-doped ZnO thin films synthesized by sol–gel method

Sb-doped ZnO thin films with different values of Sb content （from 0 to 1.1 at.%） are deposited by the sol-gel dip- coating method under different sol concentrations. The effects of Sb-doping content, sol concentration, and annealing ambient on the structural, optical, and electrical properties of ZnO films are investigated. The results of the X-ray diffraction and ultraviolet-visible spectroscopy （UV-VIS） spectrophotometer indicate that each of all the films retains the wurtzite ZnO structure and possesses a preferred orientation along the c axis, with high transmittance （〉 90%） in the visible range. The Hall effect measurements show that the vacuum annealed thin films synthesized in the sol concentration of 0.75 mol/L each have an adjustable n-type electrical conductivity by varying Sb-doping density, and the photoluminescence （PL） spectra revealed that the defect emission （around 450 nm） is predominant. However, the thin films prepared by the sol with a concentration of 0.25 mol/L, despite their poor conductivity, have priority in ultraviolet emission, and the PL peak position shows first a blue-shift and then a red-shift with the increase of the Sb doping content.     

The effect of composition on structural and electronic properties in polycrystalline CuGaSe2 thin film

Polycrystalline CuGaSe2 thin films on Mo-coated soda-lime glass substrates have been synthesized by coevaporation process from Cu, Ga and Se sources. Structural and electrical properties of the as-grown CuGaSe2 films strongly depend on the film composition. Stoichiometric CuGaSe2 is fabricated, as indicated by x-ray diffraction spectroscope （XRD） and x-ray fluorescence （XRF）. A two-phase region is composed of CuGaSe2 and Cu2-xSe phases for Cu-rich films, and CuGaSe2 and CuGa3Se5 phases for Ga-rich films, respectively. Morphological properties are detected by scanning electron microscope （SEM） for various compositional films, the grain sizes of the CuGaSe2films decrease with the extent of deviation from stoichiometric composition. Raman spectroscopy of Cu-rich samples shows that there exist large Cu-Se particles on the film surface. The results from Hall effect measurements for typical samples indicate that CuGaSe2 films are always of p-type semiconductor from Cu-rich to Ga-rich. Stoichiometric CuGaSe2 films exhibit relatively large mobility than any other compositional films. Finally, polycrystalline CuGaSe2 thin film solar cell with a best conversion efficiency of 6.02% has been achieved under the standard air mass （AM）1.5 spectrum for 100mW/cm^2 at room temperature （aperture area, 0.24cm^2）. The open circuit voltage of the CuGaSe2 solar cells is close to770 mV.     

光谱分析法研究八羧酸酞菁铝配合物与牛血清白蛋白的结合作用

以八羧酸酞菁铝配合物(AlPc(COOH)8)为红区荧光探针,用紫外光谱和荧光光谱分析方法研究了(AlPc(COOH)8)与牛血清白蛋白(BSA)的结合作用,测定了八羧酸酞菁铝与牛血清白蛋白(BSA)的结合位置数和结合常数,结果分别为n=5.7,K=5.74×105和K=3.51×105,两种分析方法结果基本一致.以氯血红素(HE)、布洛芬(IB)、L-色氨酸(TRP)为分子探针,用络合竞争法研究了它们对AlPc(COOH)8-BSA体系紫外光谱的影响,结果表明,往体系中加入HE后,AlPc(COOH)8的单体吸收峰增强,体系由结合态往游离态"转变",而加入TRP和IB后,吸收光谱未观察到明显的变化,由此确定AlPc(COOH)8与BSA的结合点为SiteⅠ.     

Structure distortion,optical and electrical properties of ZnO thin films co-doped with Al and Sb by sol-gel spin coating

ZnO thin films co-doped with Al and Sb with different concentrations and a fixed molar ratio of AlCl 3 to SbCl 3 at 1:2, are prepared by a sol-gel spin-coating method on glass annealed at 550°C for 2 h in air. The x-ray diffraction results confirm that the ZnO thin films co-doped with Al and Sb are of wurtzite hexagonal ZnO with a very small distortion, and the biaxial stresses are 1.03×10 8 , 3.26×10 8 , 5.23×10 8 , and 6.97×10 8 Pa, corresponding to those of the ZnO thin films co-doped with Al and Sb in concentrations of 1.5, 3.0, 4.5, 6.0 at% respectively. The optical properties reveal that the ZnO thin films co-doped with Al and Sb have obviously enhanced transmittance in the visible region. The electrical properties show that ZnO thin film co-doped with Al and Sb in a concentration of 1.5 at% has a lowest resistivity of 2.5Ω·cm.     

Discussion of Garfinkle-Horowitz-Strominger Dilaton Black Hole Entropy

We discuss the entropy of the Garfinkle-Horowitz-Strominger dilaton black hole by using the thin film brick-wall model, and the entropy obtained is proportional to the horizon area of the black hole confirming the Bekenstein-Hawking＇s area-entropy formula. Then, by comparing with the original brick-wall method, we find that the result obtained by the thin film method is more reasonable avoiding some drawbacks, such as little mass approximation, neglecting logarithm term, and taking the term L^3 as a contribution of the vacuum surrounding the black hole, and the physical meaning of the entropy is more clearer.