In-situ flow-cell IRAS observation of intermediates during methanol oxidation on low-index platinum surfaces.

Structural effects on intermediate species of methanol oxidation are studied on low-index planes of platinum using in-situ infrared (IR) spectroscopy. A flow cell is designed for rapid migration of reactant and product species on the electrode surface. IR spectra show adsorption of formate and the formation of carbonate species on the Pt(111) surface at potentials higher than that of CO oxidation. The band assignments for carbonate and formate are confirmed by vibrational isotope shifts. On Pt(100), the absorption band of adsorbed formate is much smaller than that on Pt(111). On the other hand, there is no adsorbed formate on Pt(110) in the potential region examined. The band intensity of formate follows the order: Pt(111)>Pt(100)>Pt(110). This order is opposite to that of the current density in the regions of higher potential. Adsorbed formate on Pt(111) behaves like a catalyst-poisoning intermediate, like adsorbed CO.     

CO and methanol adsorption on (2 × 1)Pt(110) and ion‐eroded Pt(111) model catalysts

Methanol adsorption on ion‐sputtered Pt(111) surface exhibiting high concentration of vacancy islands and on (2 × 1)Pt(110) single crystal were investigated by means of photoelectron spectroscopy (PES) and thermal desorption spectroscopy. The measurements showed that methanol adsorbed at low temperature on sputtered Pt(111) and on (2 × 1)Pt(110) surfaces decomposed upon heating. The PES data of methanol adsorption were compared to the data of CO adsorbed on the same Pt single crystal surfaces. In the case of the sputtered Pt(111) surface, the dehydrogenation of H_xCO intermediates is followed by the CO bond breakage. On the (2 × 1)Pt(110) surface, carbon monoxide, as product of methanol decomposition, desorbed molecularly without appearance of any traces of atomic carbon. By comparing both platinum surfaces we conclude that methanol decomposition occurs at higher temperature on sputtered Pt(111) than on (2 × 1)Pt(110). Copyright © 2010 John Wiley & Sons, Ltd.     

Potential oscillations in galvanostatic electrooxidation of formic acid on platinum: a time-resolved surface-enhanced infrared study

The mechanism of temporal potential oscillations that occur during galvanostatic formic acid oxidation on a Pt electrode has been investigated by time-resolved surface-enhanced infrared absorption spectroscopy (SEIRAS). Carbon monoxide (CO) and formate were found to adsorb on the surface and change their coverages synchronously with the temporal potential oscillations. Isotopic solution exchange (from H13COOH to H12COOH) and potential step experiments revealed that the oxidation of formic acid proceeds dominantly through adsorbed formate and the decomposition of formate to CO2 is the rate-determining step of the reaction. Adsorbed CO blocks the adsorption of formate and also suppresses the decomposition of formate to CO2, which raises the potential to maintain the applied current. The oxidative removal of CO at a high limiting potential increases the coverage of formate and accelerates the decomposition of formate, resulting in a potential drop and leading to the formation of CO. This cycle repeats itself to give the sustained temporal potential oscillations. The oscillatory dynamics can be explained by using a nonlinear rate equation originally proposed to explain the decomposition of formate and acetate on transition metal surfaces in UHV.     

Rh-promoted methanol decomposition on cerium oxide thin films

Methanol adsorption and reaction have been studied on Rh-deposited cerium oxide thin films under UHV conditions using temperature-programmed desorption and synchrotron soft X-ray photoelectron spectroscopy. The methanol behavior was examined as a function of the Ce oxidation state, methanol exposure, and Rh particle size and coverage. When Rh nanoparticles were deposited on the ceria films, methanol decomposed on Rh to CO and H below 200 K. H atoms recombined and desorbed between 200 and 300 K. CO evolved from Rh deposited on fully oxidized ceria between 400 and 500 K. However, on reduced ceria films, the CO on Rh further decomposed to atomic C. Methanol adsorbed on the ceria films deprotonated to form methoxy as the only intermediate on the surface. This methoxy decomposed and desorbed as CO and H2 at higher temperatures regardless of the ceria oxidation state. Compared with the methanol reaction on Rh-free ceria thin films, formaldehyde formation from methoxy was completely suppressed after Rh deposition. Our results indicate that Rh can promote the decomposition of methoxy adsorbed on the ceria and that decomposition of methoxy intermediates occurred at the metal/oxide interfaces. On the other hand, the reduced ceria can promote total methanol decomposition on Rh.     

Experimental and theoretical study of reactivity trends for methanol on Co/Pt(111) and Ni/Pt(111) bimetallic surfaces

Methanol was used as a probe molecule to examine the reforming activity of oxygenates on NiPt(111) and CoPt(111) bimetallic surfaces, utilizing density functional theory (DFT) modeling, temperature-programmed desorption, and high-resolution electron energy loss spectroscopy (HREELS). DFT results revealed a correlation between the methanol and methoxy binding energies and the surface d-band center of various NiPt(111) and CoPt(111) bimetallic surfaces. Consistent with DFT predictions, increased production of H2 and CO from methanol was observed on a Ni surface monolayer on Pt(111), designated as Ni-Pt-Pt(111), as compared to the subsurface monolayer Pt-Ni-Pt(111) surface. HREELS was used to verify the presence and subsequent decomposition of methoxy intermediates on NiPt(111) and CoPt(111) bimetallic surfaces. On Ni-Pt-Pt(111) the methoxy species decomposed to a formaldehyde intermediate below 300 K; this species reacted at approximately 300 K to form CO and H2. On Co-Pt-Pt(111), methoxy was stable up to approximately 350 K and decomposed to form CO and H2. Overall, trends in methanol reactivity on NiPt(111) bimetallic surfaces were similar to those previously determined for ethanol and ethylene glycol.     

Mechanism of CO oxidation on Pt(111) in alkaline media

Electrochemical techniques, coupled with in situ scanning tunneling microscopy, have been used to examine the mechanism of CO oxidation and the role of surface structure in promoting CO oxidation on well-ordered and disordered Pt(111) in aqueous NaOH solutions. Oxidation of CO occurs in two distinct potential regions: the prepeak (0.25-0.70 V) and the main peak (0.70 V and higher). The mechanism of reaction is Langmuir-Hinshelwood in both regions, but the OH adsorption site is different. In the prepeak, CO oxidation occurs through reaction with OH that is strongly adsorbed at defect sites. Adsorption of OH on defects at low potentials has been verified using charge displacement measurements. Not all CO can be oxidized in the prepeak, since the Pt-CO bond strength increases as the CO coverage decreases. Below theta(CO) = 0.2 monolayer, CO is too strongly bound to react with defect-bound OH. Oxidation of CO at low coverage occurs in the main peak through reaction with OH adsorbed on (111) terraces, where the Pt-OH bond is weaker than on defects. The enhanced oxidation of CO in alkaline media is attributed to the higher affinity of the Pt(111) surface for adsorption of OH at low potentials in alkaline media as compared with acidic media.     

Formate,an active intermediate for direct oxidation of methanol on pt electrode

The electro-oxidation of methanol on a Pt thin film electrode in acidic solution has been investigated by in situ surface-enhanced IR absorption spectroscopy. A new IR peak is observed at around 1320 cm-1 when the electrode potential is more positive than 0.5 V, where the bulk oxidation of MeOH occurs. This peak has been assigned to the symmetric stretching of formate species adsorbed on the Pt electrode surface. It is the first observation of formate adsorption during the electro-oxidation of methanol on a Pt surface. A near proportional relationship between the intensity of the IR band of the formate species and MeOH electro-oxidation current is observed. A new reaction scheme via non-CO pathway with formate as the active intermediate is proposed for the methanol electro-oxidation process.     

Pt（111）表面上一氧化碳的吸附与氧化反应

Ｐｔ（１１１）表面上一氧化碳的吸附与氧化反应１）刘金尧（清华大学一碳化工国家重点实验室北京１０００８４）ＸｕＭＺａｅｒａＦ（ＤｅｐａｒｔｍｅｎｔｏｆＣｈｅｍｉｓｔｒｙＵｎｉｖｅｒｓｉｔｙｏｆＣａｌｉｆｏｒｎｉａＲｉｖｅｒｓｉｄｅＣＡ９２５２１）关键词...     

Ag on Pt(111): Changes in Electronic and CO Adsorption Properties upon PtAg/Pt(111) Monolayer Surface Alloy Formation

The electronic and chemical (adsorption) properties of bimetallic Ag/Pt(111) surfaces and their modification upon surface alloy formation, that is, during intermixing of Ag and Pt atoms in the top atomic layer upon annealing, were studied by X‐ray photoelectron spectroscopy (XPS) and, using CO as probe molecule, by temperature‐programmed desorption (TPD) and infrared reflection absorption spectroscopy (IRRAS), respectively. The surface alloys are prepared by deposition of sub‐monolayer Ag amounts on a Pt(111) surface at room temperature, leading to extended Ag monolayer islands on the substrate, and subsequent annealing of these surfaces. Surface alloy formation starts at ≈600–650 K, which is evidenced by core‐level shifts (CLSs) of the Ag(3d_5/2) signal. A distinct change of the CO adsorption properties is observed when going to the intermixed PtAg surface alloys. Most prominently, we find the growth of a new desorption feature at higher temperature (≈550 K) in the TPD spectra upon surface alloy formation. This goes along with a shift of the CO_ad‐related IR bands to lower wave number. Surface alloy formation is almost completed after heating to 700 K.     

Methanol dehydrogenation and oxidation on Pt(111) in alkaline solutions

Adsorption, dehydrogenation, and oxidation of methanol on Pt(111) in alkaline solutions has been examined from a fundamental mechanistic perspective, focusing on the role of adsorbate-adsorbate interactions and the effect of defects on reactivity. CO has been confirmed as the main poisoning species, affecting the rate of methanol dehydrogenation primarily through repulsive interactions with methanol dehydrogenation intermediates. At direct methanol fuel cell (DMFC)-relevant potentials, methanol oxidation occurs almost entirely through a CO intermediate, and the rate of CO oxidation is the main limiting factor in methanol oxidation. Small Pt island defects greatly enhance CO oxidation, though they are effective only when the CO coverage is 0.20 ML or higher. Large Pt islands enhance CO oxidation as well, but unlike small Pt islands, they also promote methanol dehydrogenation. Perturbations in electronic structure are responsible for the CO oxidation effect of defects, but the role of large Pt islands in promoting methanol dehydrogenation is primarily explained by surface geometric structure.     

碱性介质中CO对甲醇在PtAu(111)和Pt(111)表面氧化生成甲酸的影响的第一性原理研究

采用密度泛函理论计算研究了碱性介质中甲醇在清洁的PtAu(111)和Pt(111)表面、及有CO存在的PtAu(111)和Pt(111)表面的氧化。计算结果表明,在碱性介质中,预吸附的CO促进了甲醇在PtAu(111)和Pt(111)表面氧化的每一步反应,这与其在Au(111)表面的作用相似。究其原因,是由于CO的吸附增强了OH的稳定性和碱性,从而增强了OH夺取氢原子的能力。     

Irrelevance of Carbon Monoxide Poisoning in the Methanol Oxidation Reaction on a PtRu Electrocatalyst

Based on detailed in situ attenuated total‐reflection–surface‐enhanced IR reflection absorption spectroscopy (ATR‐SEIRAS) studies of the methanol oxidation reaction (MOR) on Ru/Pt thin film and commercial Johnson–Matthey PtRu/C, a revised MOR enhancement mechanism is proposed in which CO on Pt sites is irrelevant but instead Pt‐Ru boundary sites catalyze the oxygen insertion reaction that leads to the formation of formate and enhances the direct reaction pathway.     

Kinetics of CO oxidation on high-concentration phases of atomic oxygen on Pt(111)

Temperature-programmed reaction spectroscopy (TPRS) and direct, isothermal reaction-rate measurements were employed to investigate the oxidation of CO on Pt(111) covered with high concentrations of atomic oxygen. The TPRS results show that oxygen atoms chemisorbed on Pt(111) at coverages just above 0.25 ML (monolayers) are reactive toward coadsorbed CO, producing CO(2) at about 295 K. The uptake of CO on Pt(111) is found to decrease with increasing oxygen coverage beyond 0.25 ML and becomes immeasurable at a surface temperature of 100 K when Pt(111) is partially covered with Pt oxide domains at oxygen coverages above 1.5 ML. The rate of CO oxidation measured as a function of CO beam exposure to the surface exhibits a nearly linear increase toward a maximum for initial oxygen coverages between 0.25 and 0.50 ML and constant surface temperatures between 300 and 500 K. At a fixed CO incident flux, the time required to reach the maximum reaction rate increases as the initial oxygen coverage is increased to 0.50 ML. A time lag prior to the reaction-rate maximum is also observed when Pt oxide domains are present on the surface, but the reaction rate increases more slowly with CO exposure and much longer time lags are observed, indicating that the oxide phase is less reactive toward CO than are chemisorbed oxygen atoms on Pt(111). On the partially oxidized surface, the CO exposure needed to reach the rate maximum increases significantly with increases in both the initial oxygen coverage and the surface temperature. A kinetic model is developed that reproduces the qualitative dependence of the CO oxidation rate on the atomic oxygen coverage and the surface temperature. The model assumes that CO chemisorption and reaction occur only on regions of the surface covered by chemisorbed oxygen atoms and describes the CO chemisorption probability as a decreasing function of the atomic oxygen coverage in the chemisorbed phase. The model also takes into account the migration of oxygen atoms from oxide domains to domains with chemisorbed oxygen atoms. According to the model, the reaction rate initially increases with the CO exposure because the rate of CO chemisorption is enhanced as the coverage of chemisorbed oxygen atoms decreases during reaction. Longer rate delays are predicted for the partially oxidized surface because oxygen migration from the oxide phase maintains high oxygen coverages in the coexisting chemisorbed oxygen phase that hinder CO chemisorption. It is shown that the time evolution of the CO oxidation rate is determined by the relative rates of CO chemisorption and oxygen migration, R(ad) and R(m), respectively, with an increase in the relative rate of oxygen migration acting to inhibit the reaction. We find that the time lag in the reaction rate increases nearly exponentially with the initial oxygen coverage [O](i) (tot) when [O](i) (tot) exceeds a critical value, which is defined as the coverage above which R(ad)R(m) is less than unity at fixed CO incident flux and surface temperature. These results demonstrate that the kinetics for CO oxidation on oxidized Pt(111) is governed by the sensitivity of CO binding and chemisorption on the atomic oxygen coverage and the distribution of surface oxygen phases.     

Enhanced reactivity of Pt nanoparticles supported on ceria thin films during ethylene dehydrogenation

The adsorption and reaction of ethylene on Pt/CeO(2-x)/Cu(111) model catalysts were studied by means of high resolution photoelectron spectroscopy (HR-PES) in conjunction with resonant photoemission spectroscopy (RPES). The dehydrogenation mechanism is compared to the HR-PES data obtained on a Pt(111) single crystal under identical conditions. It was found that the Pt nanoparticle system shows a substantially enhanced reactivity and several additional reaction pathways. In sharp contrast to Pt(111), partial dehydrogenation of ethylene on the supported Pt nanoparticles already starts at temperatures as low as 100 K. Similar to the single crystal surface, dehydrogenation occurs via the isomer ethylidene (CHCH(3)) and then mainly via ethylidyne (CCH(3)). In the temperature region between 100 and 250 K there is strong evidence for spillover of hydrocarbon fragments to the ceria support. In addition, splitting of ethylene to C(1) fragments is more facile than on Pt(111), giving rise to the formation of CH species and CO in the temperature region between 250 and 400 K. Upon further annealing, carbonaceous deposits are formed at 450 K. By heating to 700 K, these carbon deposits are completely removed from the surface by reaction with oxygen, provided by reverse spillover of oxygen from the ceria support.     

Dynamics of CO at the solid/liquid interface studied by modeling and simulation of CO electro-oxidation on Pt and PtRu electrodes

We consider theoretical models for CO monolayer oxidation on stepped Pt single-crystal electrodes and Ru-modified Pt(111) electrodes. For both systems, our aim is to assess the importance of CO surface diffusion in reproducing the experimental chronoamperometry or voltammetry. By comparing the simulations with the experimental chronoamperometric transients for CO oxidation on a series of stepped Pt surfaces, it was concluded that mixing of CO on the Pt(111) terrace is good, implying rapid diffusion (N. P. Lebedeva, M. T. M. Koper, J. M. Feliu and R. A. van Santen, J. Phys. Chem. B, submitted). We discuss here a more detailed model in which the CO adsorbed on steps is converted into CO adsorbed on terraces as the oxygen-containing species occupy the steps (as observed experimentally on stepped Pt in UHV), followed by a subsequent oxidation of the latter, to reproduce the observed chronoamperometry on stepped surfaces with a higher step density. On Ru-modified Pt(111), the experimentally observed splitting of the CO stripping voltammetry into two stripping peaks, may suggest a slow diffusion of CO on Pt(111). This apparent contradiction with the conclusions of the experiments on stepped surfaces, is resolved by assuming a weaker CO binding to a Pt atom which has Ru neighbors than to "bulk" Pt(111), in agreement with recent quantum-chemical calculations. This makes the effective diffusion from the uncovered Pt(111) surface to the perimeter of the Ru islands, which are considered to be the active sites in CO oxidation electrocatalysis on PtRu surfaces, very slow. Different models for the reaction are considered, and discussed in terms of their ability to explain experimental observations.     

IR chemiluminescence probe of the vibrational energy distribution of CO2 formed during steady-state CO oxidation on Pt(111) and Pt(110) surfaces

The infrared (IR) chemiluminescence spectra of CO2 were measured during the steady-state CO + O2 reaction over Pt(110) and Pt(111) surfaces. Analysis of the IR emission spectra indicates that the bending vibrational temperature (TVB), as well as the antisymmetric vibrational temperature (TVAS), was higher on Pt(110) than on Pt(111). On the Pt(110) surface, the highly excited bending vibrational mode compared to the antisymmetric vibrational mode was observed under reaction conditions at low CO coverage (theta(CO) < 0.2) or at high surface temperatures (TS > or = 700 K). This can be related to the activated complex of CO2 formation in a more bent form on the inclined (111) terraces of the Pt(110)(1 x 2) structure. On the other hand, at high CO coverage (theta(CO) > 0.2) or at low surface temperatures (TS < 650 K), TVAS was higher than TVB, which can be caused by the reconstruction of the Pt(110)(1 x 2) surface to the (1 x 1) form with high CO coverage.     

Characterization and methanol electrooxidation studies of Pt(111)/Os surfaces prepared by spontaneous deposition

Catalytic activity of the Pt(111)/Os surface toward methanol electrooxidation was optimized by exploring a wide range of Os coverage. Various methods of surface analyses were used, including electroanalytical, STM, and XPS methods. The Pt(111) surface was decorated with nanosized Os islands by spontaneous deposition, and the Os coverage was controlled by changing the exposure time to the Os-containing electrolyte. The structure of Os deposits on Pt(111) was characterized and quantified by in situ STM and stripping voltammetry. We found that the optimal Os surface coverage of Pt(111) for methanol electrooxidation was 0.7 +/- 0.1 ML, close to 1.0 +/- 0.1 Os packing density. Apparently, the high osmium coverage Pt(111)/Os surface provides more of the necessary oxygen-containing species (e.g., Os-OH) for effective methanol electrooxidation than the Pt(111)/Os surfaces with lower Os coverage (vs e.g., Ru-OH). Supporting evidence for this conjecture comes from the CO electrooxidation data, which show that the onset potential for CO stripping is lowered from 0.53 to 0.45 V when the Os coverage is increased from 0.2 to 0.7 ML. However, the activity of Pt(111)/Os for methanol electrooxidation decreases when the Os coverage is higher than 0.7 +/- 0.1 ML, indicating that Pt sites uncovered by Os are necessary for sustaining significant methanol oxidation rates. Furthermore, osmium is inactive for methanol electrooxidation when the platinum substrate is absent: Os deposits on Au(111), a bulk Os ingot, and thick films of electrodeposited Os on Pt(111), all compare poorly to Pt(111)/Os. We conclude that a bifunctional mechanism applies to the methanol electrooxidation similarly to Pt(111)/Ru, although with fewer available Pt sites. Finally, the potential window for methanol electrooxidation on Pt(111)/Os was observed to shift positively versus Pt(111)/Ru. Because of the difference in the Os and Ru oxophilicity under electrochemical conditions, the Os deposit provides fewer oxygen-containing species, at least below 0.5 V vs RHE. Both higher coverage of Os than Ru and the higher potentials are required to provide a sufficient number of active oxygen-containing species for the effective removal of the site-blocking CO from the catalyst surface when the methanol electrooxidation process occurs.     

At least three contiguous atoms are necessary for CO formation during methanol electrooxidation on platinum

We have used cyanide-modified Pt(111) electrodes to investigate the size and geometry of the minimum atomic ensemble necessary for the oxidation of methanol on Pt electrodes. Poison formation on cyanide-modified Pt(111) is completely inhibited, the corresponding electrooxidation reaction proceeding, hence, exclusively through the reactive intermediate pathway. These results suggest that formation of adsorbed CO would require the presence of at least three contiguous Pt atoms.     

Interface-controlled synthesis of CeO2(111) and CeO2(100) and their structural transition on Pt(111)

Ceria-based catalytic materials are known for their crystal-face-dependent catalytic properties. To obtain a molecular-level understanding of their surface chemistry, controlled synthesis of ceria with well-defined surface structures is required. We have thus studied the growth of CeO_x nanostructures (NSs) and thin films on Pt(111). The strong metal-oxide interaction has often been invoked to explain catalytic processes over the Pt/CeO_x catalysts. However, the Pt-CeO_x interaction has not been understood at the atomic level. We show here that the interfacial interaction between Pt and ceria could indeed affect the surface structures of ceria, which could subsequently determine their catalytic chemistry. While ceria on Pt(111) typically exposes the CeO₂(111) surface, we found that the structures of ceria layers with a thickness of three layers or less are highly dynamic and dependent on the annealing temperatures, owing to the electronic interaction between Pt and CeO_x. A two-step kinetically limited growth procedure was used to prepare the ceria film that fully covers the Pt(111) substrate. For a ceria film of ~3–4 monolayer (ML) thickness on Pt(111), annealing in ultrahigh vacuum (UHV) at 1000 K results in a surface of CeO₂ (100), stabilized by a c-Ce₂O₃(100) buffer layer. Further oxidation at 900 K transforms the surface of the CeO₂(100) thin film into a hexagonal CeO₂(111) surface.     

Stripping voltammetry of carbon monoxide oxidation on stepped platinum single-crystal electrodes in alkaline solution

The electrochemical oxidation of a CO adlayer on Pt[n(111)x(111)] electrodes, with n = 30, 10, and 5, Pt(111), Pt(110) as well as a Pt(553) electrode (with steps of (100) orientation) in alkaline solution (0.1 M NaOH) has been studied using stripping voltammetry. On these electrodes, it is possible to distinguish CO oxidation at four different active oxidation sites on the surface, i.e. sites with (111), (110) and (100) orientation, and kink sites. The least active site for CO oxidation is the (111) terrace site. Steps sites are more active than the (111) terrace sites, the (110) site oxidizing CO at lower potential than the (100) site. The CO oxidation feature with the lowest overpotential (oxidation potential as low as 0.35 V vs. RHE) was ascribed to oxidation of CO at kink sites. The amount of CO oxidized at the active step or kink sites vs. the amount of CO oxidized at the (111) terrace sites depends on the concentration of the active sites and the time given for the terrace-bound CO to reach the active site. By performing CO stripping on the stepped surfaces at different scan rates, the role of CO surface diffusion is probed. The possible role of electronic effects in explaining the unusual activity and dynamics of CO adlayer oxidation in alkaline solution is discussed.