离子色谱法测定核电站一回路冷却剂中痕量F~-,Cl~-和SO_4~(2-)

建立离子色谱法测定核电站一回路冷却剂中痕量氟离子F~-,氯离子Cl~-,硫酸根离子SO_4~(2-)的方法。采用80 mmol/L硼酸溶液配合氢氧化钾淋洗液发生器在线生成淋洗液,梯度洗脱,淋洗液流量为1.2 mL/min,在选定的分析条件下,NO_2~-,NO_3~-,PO_4~(3-)和CO_3~(2-)不干扰F~-,Cl~-,SO_4~(2-)的测定。F~-,Cl~-,SO_4~(2-)的质量浓度与其色谱峰面积呈良好的线性关系,线性相关系数分别为0.999 8,0.999 5,0.999 7,线性范围分别为0.85~30.0,2.65~30.0,2.00~30.0μg/L。F~-,Cl~-,SO_4~(2-)测定结果的相对标准偏差分别为0.56%~1.58%,0.85%~3.62%,1.21%~4.60%(n=7)。F~-,Cl~-,SO_4~(2-)的加标回收率分别为98%~104%,98%~108%,93%~108%。该方法快速、准确,满足核电站一回路冷却剂中痕量F~-,Cl~-,SO_4~(2-)的检测要求。     

单柱离子色谱法测定硒酸根和亚硒酸根的研究

本实验采用单柱离子色谱系统,在SeO_4~(2-)、SeO_3~(2-)与F~-、Cl~-、NO_3~-、SO_4~(2-)离子共存时,以1.0mmol/L邻苯二甲酸氢钾为淋洗液测定了SeO_4~(2-),以1.0mmol/LKNO_3为淋洗液测定了SeO_3~(2-)。SeO_4~(1-)和SeO_3~(2-)的最低检出浓度分别为0.3μg/mL和0.7μg/mL,线性范围分别为0.8～80μg/mL和1.4～150μg/mL,相对标准偏差分别为2.01%和1.85%。并应用本方法测定了加SeO_4~(2-)和SeO_3~(2-)的自来水样,SeO_4~(2-)和SeO_3~(2-)的回收率分别为96%和98%。     

在线超滤-离子色谱法测定降水中4种阴离子

建立在线超滤–离子色谱法测定降水中4种阴离子。采用在线超滤技术,以Metrosep A Supp 5–150色谱柱为分析柱,3.2 mmol/L Na_2CO_3–1.0 mmol/LNaHCO_3溶液为淋洗液,流量为0.7 mL/min,0.5%H_2SO_4为抑制器再生液,用离子色谱法对降水中4种阴离子进行测定。氟离子、氯离子、硝酸根离子、硫酸根离子质量浓度在各自范围内与色谱峰面积呈良好的线性关系,相关系数均大于0.999,方法检出限为0.005～0.015 mg/L。测定结果的相对标准偏差为0.7%～2.2%(n=6),样品加标回收率为97.0%～103.0%。该法操作简单、成本低,适于大气降水中阴离子的测定。     

超声提取–离子色谱法测定土壤易溶盐中的氯离子和硫酸根离子

采用超声提取的方式,以离子色谱法测定土壤易溶盐中的氯离子和硫酸根离子。对实验条件进行了优化,色谱柱为NJ–SA–4A柱(250 mm×2 mm),保护柱为SI–92G柱(50 mm×4 mm),淋洗液为1.8 mmol/L Na_2CO_3–1.7mmol/L NaHCO_3,流量为1.0 m L/min;在40℃下,对土壤样品提取10 min。Cl~–和SO_4~(2–)在检测范围内均线性良好,线性相关系数为0.999 8,加标回收率分别为95.0%~99.0%,96.0%~101.0%,测定结果的相对标准偏差分别为1.4%,1.0%(n=4)。与传统的方法相比,该法试剂用量少,操作简单,可用于土壤易溶盐样品的测定。     

在线固相萃取-离子色谱法测定4种芳环磺酸盐中的硫酸根离子

建立一种在线固相萃取-离子色谱测定4种芳环磺酸盐中硫酸根离子含量的新方法。将自装填的多孔石墨化碳固相萃取柱应用于离子色谱系统,对样品进行在线前处理。样品经过多孔石墨化碳固相萃取柱基体消除后进入收集环,通过阀切换方式使待测硫酸根离子转入阴离子分析柱和检测系统。固相萃取流路用1.5 mmol/L碳酸钠以0.8 mL/min的流速对基体在线富集,进样量为20μL,分析柱为SH-AC-3(250 mm×4.0 mm)+SH-AG-3(50 mm×4.0 mm)色谱柱,柱温为35℃,在6 mmol/L碳酸钠-4 mmol/L碳酸氢钠条件下等度洗脱,流速为0.8 mL/min。结果表明:硫酸根离子在0.50~20.00 mg/L范围内呈良好的线性关系,线性相关系数为0.998 3,保留时间、峰高和峰面积的相对标准偏差均在0.28%~2.86%之间,方法检出限为0.010 6 mg/L,回收率为91.01%~109.3%,具有良好的线性关系和重复性。整个在线分析过程在25 min之内完成。该方法进样量少、快速、高效。     

离子色谱法测定硫酸钙样品中的硫酸根

用碳酸钠将硫酸钙样品中的钙沉淀为碳酸钙,释放出硫酸根,用阴离子型离子色谱仪,在40℃柱温下,以6.3 mmol/L Na HCO3–1.7 mmol/L Na2CO3缓冲盐为淋洗液,采用电导检测器测定其中硫酸根的浓度,以间接得到硫酸钙含量。实验结果表明,该法与经典的沉淀重量法测定结果相吻合,两者之间的相对误差为0.29%。样品加标回收率在96.0%~105.3%之间,测定结果的相对标准偏差为0.26%(n=6)。该方法精密度与准确度高,可快速、稳定、可靠地分析脱硫灰渣及石膏样品中的硫酸根含量。     

基于氧弹燃烧-离子色谱法测定生活垃圾可燃组分中氯和硫的含量

采用氧弹燃烧法对垃圾样品干燥基进行前处理,用碳酸钠(24 mmol/L)和碳酸氢钠(30 mmol/L)以及过氧化氢(2.5%)为吸收液,并用离子色谱法对其处理后吸收液中氯离子和硫酸根含量进行测定,最后换算为样品中氯和硫的含量。氯和硫酸根质量浓度分别在1~50 mg/L与色谱峰面积呈良好的线性相关,其线性相关系数都大于0.999。样品中氯的加标回收率为96.5%~99.1%,硫酸根的加标回收率为92.5%~101%,测定结果中样品的相对平均标准偏差均小于3%(n=5),并用质控样品对方法进行了验证,结果表明样品的前处理方法简单、样品损失少、准确度高,适合于垃圾样品可燃组分中氯和硫含量的测定。     

管式炉燃烧–离子色谱法测定车用柴油中的硫

建立一种管式炉燃烧–离子色谱法测定车用柴油中硫含量的方法。分别对取样量、涂布形状、管式炉的加热温度和加热速率、吸收液等影响因素进行了分析。样品经管式炉燃烧,在吸收液中转化成硫酸根离子,选用Dionex IonPac AS_(18)阴离子分析柱,以10 mmol/L NaOH溶液作为淋洗液,流量为1.0 mL/min,进样体积为20μL,以抑制电导检测器测定硫酸根离子的含量。硫酸根离子的质量浓度在0.01～5.00 mg/L范围内与色谱峰面积呈良好的线性关系,相关系数为0.999 8,方法检出限(S/N=3)为0.003 6 mg/L。测定结果的相对标准偏差小于5%(n=6),样品的平均加标回收率为96.63%～99.33%。该方法操作简便、快速,可用于车用柴油产品中总硫含量的测定。     

碱化底液消除水负峰离子色谱法测定水中F~–,Cl~–等7种阴离子

在研究消除水负峰的基础上,建立离子色谱法测定水中F–,Cl–,NO2–,H2PO4–,Br–,NO3–,SO42–7种阴离子的方法。经实验确定淋洗液为4.5 mmol/L NaHCO3–4.0 mmol/L Na2CO3,淋洗液流量为1.0 mL/min,柱箱温度为35℃。在底液中加入与淋洗液同浓度的Na2CO3–NaHCO3可有效消除水负峰。该方法对7种阴离子的检出限为0.004~0.034 mg/L,测定结果的相对标准偏差为0.69%~3.57%(n=6),加标回收率为95%~105%。该法能有效消除水负峰及其对F–测定的影响,操作简便、测定结果准确可靠,适用于水中F–、Cl–等7种阴离子的测定。     

氧弹燃烧-离子色谱法测定煤中氯含量

建立了氧弹燃烧-离子色谱测定煤中氯含量的方法.在加有(NH4)2CO3溶液和过量氧气的氧弹中燃烧煤样,释放的氯被(NH4)2CO3溶液吸收,过滤溶液后, 采用离子色谱外标法测定滤液中氯的浓度,最后计算出煤中氯的含量.色谱工作条件:淋洗液为1.8 mmol/L Na2CO3与1.7 mmol/L NaHCO3混合液,流速1 mL/min;再生液为40 mmol/L H2SO4,流速0.5 mL/min;进样量20 μL.色谱标准工作曲线线性相关系数0.9996;10次测定1 mg/L Cl-标准溶液的均值为1.0012 mg/L,相对标准偏差为1.34%;8个煤样加标回收率为90.7%～104.3%;测定标准物质GBW11119 及GBW11120的相对误差分别为1.75%和1.36%;对比研究显示,氧弹燃烧-离子色谱测定8个煤样(除两个煤样外)氯含量结果远高于艾士卡剂混合熔样-离子色谱测定结果,表明艾士卡剂混合熔样过程由于煤样未处于完全密闭状态导致部分氯的散失.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.