Swiss-Roll燃烧器催化剂结构的实验研究

实验研究了装有Pt覆盖的多孔陶瓷的Swiss-Roll燃烧器的燃烧特性,分别得到了3种不同长度的催化剂基底的熄火极限,并测量3种情况下催化剂壁面及催化剂后部空间的温度。实验结果表明,3种情况中,催化剂基底长4.5mm的燃烧器可燃范围最大,所以此长度较适合此Swiss-Roll燃烧器。从温度数据可以看出来,催化剂后部空间存在反应,且受上游催化剂表面反应强度的影响。     

CFD analysis of the HyShot II scramjet combustor

The development of novel air-breathing engines such as supersonic combustion ramjets (scramjets) depends on the understanding of supersonic mixing, self-ignition and combustion. These aerothermochemical processes occur together in a scramjet engine and are notoriously difficult to understand. In the present study, we aim at analyzing the HyShot II scramjet combustor mounted in the High Enthalpy Shock Tunnel Göttingen (HEG) by using Reynolds Averaged Navier Stokes (RANS) and Large Eddy Simulation (LES) models with detailed and reduced chemistry. To account for the complicated flow in the HEG facility a zonal approach is adopted in which RANS is used to simulate the flow in the HEG nozzle and test-section, providing the necessary inflow boundary conditions for more detailed RANS and LES of the reacting flow in the HyShot combustor. Comparison of predicted wall pressures and heat fluxes with experimental data show good agreement, and in particular does the LES agree well with the experimental data. The LES results are used to elucidate the flow, mixing, self-ignition and subsequent combustion processes in the combustor. The combustor flow can be separated into the mixing zone, in which turbulent mixing from the jet-in-cross flow injectors dominates, the self-ignition zone, in which self-ignition rapidly takes place, and the turbulent combustion zone, located towards the end of the combustor, in which most of the heat release and volumetric expansion takes place. Self-ignition occurs at some distance downstream of the injectors, resulting in a distinct pressure rise further downstream due to the volumetric expansion as observed in the experiments. The jet penetration is about 30% of the combustor height and the combustion efficiency is found to be around 83%.     

H2/n-C4H10/Air预混气在Swiss-Roll燃烧器中的催化燃烧特性

在微尺度催化燃烧中,由于燃料和氧气对于催化剂表面活性位的竞争,导致了可燃下限为富燃的情况。为了提高燃料利用率,拓宽可燃范围,本文在正丁烷/空气的混合气中加入一定量的氢气,在Swiss-roll燃烧器内研究了氢气/正丁烷/空气预混气的燃烧特性。结果表明,氢气能够有效拓宽正丁烷的可燃范围,可燃下限能够低于1,以贫燃的条件实现高燃料利用率。对于稳定燃烧温度的实验结果表明,燃烧器最高温度出现在富燃料一侧。     

甲烷微尺度催化燃烧的数值模拟

本文联合使用计算流体力学软件FLUENT和可以计算表面反应的化学反应动力学软件DETCHEM对有逆流换热的微尺度燃烧器进行了数值计算。计算中忽略空间反应。燃料-空气混合物的当量比为0.4,反应器壁面采用等温边界条件。计算结果表明,采用催化燃烧可以实现微尺度下通常情况下无法实现的甲烷稳定燃烧。通过适当设置催化表面,可以实现燃料低温、高效转变。甲烷的总转变率受流动状态、反应温度和催化表面的大小等因素的影响。     

Modeling of a self-excited pulse combustor and stability analysis

The major bottleneck for popularization and utilization of the conventional mechanical valve pulse combustors is the self-priming mode of gas supply. An aerodynamic valve (as against mechanical valve) self-excited pulse combustor of the Helmholtz-type with continuous supply of gas and air was designed and a mathematical model was established in this paper. The theoretical model employed well-stirred reactor model and a single step Arrhenius chemistry, and took those factors which might affect the combustion stability into account. The factors include the variation of the mass rate of the reactants affected by the pressure in the combustion chamber, the convective and radiation heat loss in the combustion chamber, and the heat transfer and wall friction in the tailpipe. The effect of wall temperature of combustion chamber, wall heat transfer coefficient, tailpipe length and friction coefficient on combustionstability were analyzed. The range of combustion oscillations can be predicted. It is theoretically and experimentally shown that combustion oscillations can be produced with a continuous supply of fuel and air without mechanical valves. The experimental data show qualitative agreement with predictions from the theoretical model. The theoretical model could be a tool for designing and optimizing the self-excited pulse combustor.     

Simulation of a round supersonic combustor using wall-modeled large eddy simulation and partially-stirred reactor models

Simulations are presented for a generic, round supersonic combustor. Turbulence is modeled in the combustor using a wall-modeled large eddy simulation approach. Combustion is modeled using a small quasi-global mechanism and a more detailed skeletal mechanism. Both mechanisms are used in conjunction with two variations of the partially-stirred reactor model for sub-grid turbulence chemistry interactions. Sensitivity of the solutions to grid resolution is investigated. It is found that in order to achieve reasonable grid convergence in the mean wall pressure, the model constant that appears in the partially-stirred reactor model must be a function of both the chemistry mechanism and the grid resolution. Most of the combinations of mechanism and turbulent combustion model tested can be tuned in order to predict the location of the pre-combustion shock train and the peak mean pressure in the combustor. It is found that while the different models are able to reproduce the mean wall pressure, there are significant differences in the mean temperature and heat release rate fields. The sensitivity of the different combinations of mechanisms and partially-stirred reactor formulation is quantified and some combinations are found to be more prone to blowout. Two of the tuned models were tested across several fuel equivalence ratios with a single value of the partially-stirred reactor model constant. One model produced reasonable predictions of shock location and peak mean pressure for each equivalence ratio. The second model captured the global trends in the mean wall pressure, but was unable to quantitatively predict the shock location and peak mean pressure for all equivalence ratios tested.     

Modélisation numérique des écoulements réactifs dans les foyers de turboréacteurs

Some assumptions have to be made to deal with combustion and aerodynamical phenomena simultaneously. We propose a turbulent combustion model where we consider a one step reaction for chemical modelling. Consequently, only two variables are sufficient to describe the problem. In fact, the combustion can be characterized by the consumption of one of the two reactive species. In a first step, to obtain the instantaneous consumption rate, we model the Lagrangian equation of the fuel mass fraction by considering only the equilibrium state. This state is calculated in order to obtain the same temperature as with a detailed kinetic scheme. In a second step, the mean consumption rate is calculated with the instantaneous consumption rate and a presumed probability density function. This model has been tested on many configurations, particularly, on a non-premixed flame and an experimental industrial combustor. Results from these validations show that this model can be used to predict temperature level in an industrial combustor.     

燃油分级多点喷射低污染燃烧室的化学反应网络模型分析

本文采用基于详细化学反应机理的化学反应网络模型分析了航空发动机燃油径向分级多点喷射低污染燃烧室的NO_x排放特性。该分级燃烧室不同于传统燃烧室,头部由值班区和主燃区两个不同的燃烧区域,根据CFD得到的流场特性和当量比的分布特性对燃烧室进行分区构建化学反应器网络模型,研究了值班级当量比以及值班级和主燃级两级供油比例对排放的影响。同时,还分析了空气进口温度对NO_x排放的影响。得到了较为合理的变化趋势,为低污染燃烧室的初步设计提供了有益的指导。     

Effect of fuel injection location on a plasma jet assisted combustion with a backward-facing step

Non-reacting and reacting experiments on the ignition by a plasma jet (PJ) torch were performed to understand the correlation between fuel injection location and combustion characteristics in unheated Mach 2 airflow. Fuel was injected through three sonic injectors in the recirculation region behind a backward-facing step: a parallel injector at 2 mm from the bottom wall and two normal injectors at 2 and 9 mm from the step wall. In order to mitigate the combustion pressure interaction with nozzle, an isolator was installed between the nozzle and combustor. The combustion performance of normal injection was little affected by the difference of fuel injection locations. Moreover, normally injected fuel was escaped not to be held in the recirculation region despite of low fuel injection rates. This led to lower combustion performance relative to the parallel injection which provided fuel not to leave the recirculation region. In this case, the role of the recirculation region was to fully hold fuel, and the PJ torch provided hot gases as a heat source and acted as a flame-holder to ignite fuel–air mixtures. In a low temperature inflow condition, combustible regions were constrained around the bottom wall where embedded with the PJ torch. When thermal choking occurred in the combustor, it induced shock train both in the combustor and isolator. Under this unstable condition, the combustion performance of the normal injection was lower than that of the parallel injection. This is because the normal injection led most fuel into low temperature incoming air-stream.     

Scaling study of the combustion performance of gasben gas rocket injectors

To obtain the key subelements that may influence the scaling of gas-gas injector combustor performance, the combustion performance subelements in a liquid propellant rocket engine combustor are initially analysed based on the results of a previous study on the scaling of a gas-gas combustion flowfield. Analysis indicates that inner wall friction loss and heat-flux loss are two key issues in gaining the scaling criterion of the combustion performance. The similarity conditions of the inner wall friction loss and heat-flux loss in a gas-gas combustion chamber are obtained by theoretical analyses. Then the theoretical scaling criterion was obtained for the combustion performance, but it proved to be impractical. The criterion conditions, the wall friction and the heat flux are further analysed in detail to obtain the specific engineering scaling criterion of the combustion performance. The results indicate that when the inner flowfields in the combustors are similar, the combustor wall shear stress will have similar distributions qualitatively and will be directly proportional to p_c^0.8 d_t^-0.2 quantitatively. In addition, the combustion peformance will remain unchanged. Furthermore, multi-element injector chambers with different geometric sizes and at different pressures are numerically simulated and the wall shear stress and combustion efficiencies are solved and compared with each other. A multi-element injector chamber is designed and hot-fire tested at several chamber pressures and the combustion performances are measured in a total of nine hot-fire tests. The numerical and experimental results verified the similarities among combustor wall shear stress and combustion performances at different chamber pressures and geometries, with the criterion applied.     

Scaling of heat transfer in gas-gas injector combustor

The scaling of heat transfer in gas-gas injector combustor is investigated theoretically, numerically and experimentally based on the previous study on the scaling of gas-gas combustion flowfield. The similarity condition of the gas-gas injector combustor heat transfer is obtained by conducting a formulation analysis of the boundary layer Navier-Stokes equations and a dimensional analysis of the corresponding heat transfer phenomenon. Then, a practicable engineering scaling criterion of the gas-gas injector combustor heat transfer is put forward. The criterion implies that when the similarity conditions of inner flowfield are satisfied, the size and the pressure of gas-gas combustion chamber can be changed, while the heat transfer can still be qualitatively similar to the distribution trend and quantitatively correlates well with the size and pressure as q ∝ pc0 .8d t-0.2. Based on the criterion, single-element injector chambers with different geometric sizes and at different chamber pressures ranging from 1 MPa to 20 MPa are numerically simulated. A single-element injector chamber is designed and hot-fire tested at seven chamber pressures from 0.92 MPa to 6.1 MPa. The inner wall heat flux are obtained and analysed. The numerical and experimental results both verified the scaling criterion in gas-gas injector combustion chambers under different chamber pressures and geometries.     

Application and theoretical analysis of the flamelet model for supersonic turbulent combustion flows in the scramjet engine

In the framework of Reynolds-averaged Navier–Stokes simulation, supersonic turbulent combustion flows at the German Aerospace Centre (DLR) combustor and Japan Aerospace Exploration Agency (JAXA) integrated scramjet engine are numerically simulated using the flamelet model. Based on the DLR combustor case, theoretical analysis and numerical experiments conclude that: the finite rate model only implicitly considers the large-scale turbulent effect and, due to the lack of the small-scale non-equilibrium effect, it would overshoot the peak temperature compared to the flamelet model in general. Furthermore, high-Mach-number compressibility affects the flamelet model mainly through two ways: the spatial pressure variation and the static enthalpy variation due to the kinetic energy. In the flamelet library, the mass fractions of the intermediate species, e.g. OH, are more sensible to the above two effects than the main species such as H₂O. Additionally, in the combustion flowfield where the pressure is larger than the value adopted in the generation of the flamelet library or the conversion from the static enthalpy to the kinetic energy occurs, the temperature obtained by the flamelet model without taking compressibility effects into account would be undershot, and vice versa. The static enthalpy variation effect has only little influence on the temperature simulation of the flamelet model, while the effect of the spatial pressure variation may cause relatively large errors. From the JAXA case, it is found that the flamelet model cannot in general be used for an integrated scramjet engine. The existence of the inlet together with the transverse injection scheme could cause large spatial variations of pressure, so the pressure value adopted for the generation of a flamelet library should be fine-tuned according to a pre-simulation of pure mixing.     

微型火焰管中燃烧的研究

提出了一种新型的微动力机电系统观念,即微型热光电 TPV(thermo photovoltaic)系统。微型燃烧室是微型TPV系统中最重要的部分之一。为了获得较高的能量转换效率,需要使燃烧器壁面四周处于较高且分布均匀的温度状态。尺寸效应对微型燃烧室中的持续燃烧带来了很大的影响。为了分析微型燃烧器中燃烧的可行性和有关影响因素,在不同工况下进行实验。结果表明,在一定的流量和混合比范围内,可以在微型火焰管内维持稳定的燃烧,高温能够在燃烧室四周均匀分布。     

In situ parametric study of alkali release in pulverized coal combustion: Effects of operating conditions and gas composition

This work concerns a parametric study of alkali release in a lab-scale, pulverized coal combustor (drop tube reactor) at atmospheric pressure. Measurements were made at steady reactor conditions using excimer laser fragmentation fluorescence (ELIF) and with direct optical access to the flue gas pipe. In this way, absolute gas-phase alkali species could be determined in situ, continuously, with sub-ppb sensitivity, directly in the flue gas. A hard coal was fired in the range 1000–1300 °C, for residence times in the range 3–5 s and for air numbers λ (air/fuel ratios) from 1.15 to 1.50. In addition, the amount of chlorine, water vapor and sulfur, respectively, was increased in known amounts by controlled dosing of HCl, H₂O and SO₂ into the combustion gas to determine effects of these components on release or capture of the alkali species. The experimental results are also compared with values calculated using ash/fuel analyses and sequential extraction to obtain a fuller picture of alkali release in pulverized fuel combustion.     

Uncertainty quantification in the catalytic partial oxidation of methane

This work focuses on uncertainty quantification of eight random parameters required as input for 1D modelling of methane catalytic partial oxidation within a highly dense foam reactor. Parameters related to geometrical properties, reactor thermophysics and catalyst loading are taken as uncertain. A widely applied 1D heterogeneous mathematical model that accounts for proper transport and surface chemistry steps is considered for the evaluation of deterministic samples. The non-intrusive spectral projection approach based on polynomial chaos expansion is applied to determine the stochastic temperature and species profiles along the reactor axial direction as well as their ensemble mean and error bars with a confidence interval of 95%. Probability density functions of relevant variables in specific reactor sections are also analysed. A different contribution is noticed from each random input to the total uncertainty range. Porosity, specific surface area and catalyst loading appear as the major sources of uncertainty to bulk gas and surface temperature and species molar profiles. Porosity and the mean pore diameter have an important impact on the pressure drop along the whole reactor as expected. It is also concluded that any trace of uncertainty in the eight input random variables can be almost dissipated near the catalyst outlet section for a long-enough catalyst, mainly due to the approximation to thermodynamic equilibrium.     

涡轮导向器对旋转爆轰波传播特性影响的实验研究

为了研究涡轮导向器对旋转爆轰波传播特性的影响,以氢气为燃料,空气为氧化剂,在不同当量比下开展了实验研究.基于高频压力传感器及静态压力传感器的信号,详细分析了带涡轮导向器的旋转爆轰燃烧室的工作模式以及涡轮导向器对非均匀不稳定爆轰产物的影响.实验结果表明:在当量比较低时,爆轰燃烧室以快速爆燃模式工作;逐渐增大当量比,爆轰燃烧室开始以不稳定旋转爆轰模式工作;继续增大当量比,爆轰燃烧室以稳定旋转爆轰模式工作,且旋转爆轰波的传播速度和稳定性均随当量比的增大逐渐提高.爆轰波下游的斜激波与涡轮导向器相互作用,涡轮导向器对压力振荡的幅值具有明显的抑制作用,但对压力振荡频率的影响较小.随着当量比的增大,涡轮导向器上下游的静压均同时增大,经过涡轮导向器的作用,涡轮下游静压明显降低.     

新一代航空发动机燃烧室

针对新一代高油气比(0.051及以上)航空发动机燃烧室,本文提出头部采用化学恰当比直接混合燃烧设计方案.对于新一代高压比(70及以上)低排放民用航空发动机燃烧室,由于其自着火延迟时间极短,因此采用贫油直接混合燃烧,而不能采用预混合预蒸发燃烧.本文提出了一种贫油直接混合低排放燃烧室方案,其燃油空气模由简单的压力雾化喷嘴和...     

进口条件对超燃冲压发动机氢气燃烧流场特性的影响分析

对不同进口条件下的超燃冲压发动机燃烧室内氢气喷流超声速燃烧流动特性进行了数值模拟与分析.宽范围超燃冲压发动机是吸气式高超声速飞行器推进系统设计中的热点问题之一,受实验设备硬件条件及实验技术限制,数值模拟技术仍然是超燃冲压发动机燃烧室内燃气燃烧特性及流场特性的主要研究手段.采用基于混合网格技术的多组元N-S方程有限体积方法求解器,在不同进口Mach数及压强条件下,对带楔板/凹腔结构的燃烧室模型氢气喷流燃烧流场进行了数值模拟,对比分析了氢气喷流穿透深度、喷口前后回流区结构、掺混效率及燃烧效率等流场结构与典型流场参数的变化特性及影响规律.研究成果可为宽范围超燃冲压发动机喷流燃烧流动特性分析提供参考.      

Characterizing continuously rotating detonation via nonlinear time series analysis

The sampled pressure signals in continuously rotating detonation combustors have the inherence of nonlinear dynamics. To dig out more information on combustion modes, the nonlinear time series analysis method is thus applied to the pressure-time series obtained at a hydrogen/air rotating detonation combustor by using the phase space reconstruction and wavelet entropy algorithm. The variation of wavelet entropy is approved to be associated with the periodicity variation of pressure signals. Different structures of attractor as well as wavelet entropy distribution in the phase diagram can distinguish the deflagration mode from the unstable and stable detonation modes under the conditions of different air flow rates. The limit-cycle oscillation is exhibited in the phase space diagram with a very low flow rate, here 25 g/s. The mean wavelet entropy of pressure-time series can be a quantitative index of different combustion modes occurring in the combustor. The present study is expected to enhance the understanding of the physical mechanism of continuously rotating detonation and contribute on the development of detonation propulsion technology.