Optical detection of organic hydrides with platinum-loaded tungsten trioxide

Tungsten trioxide powder with loading 0.1 wt% platinum (Pt/WO₃) was prepared for optical detection of organic hydrides such as cyclohexane, decalin by impregnation with PtCl₆^2? and subsequent calcination in air at 500 °C. The scanning electron microscopic observation of Pt/WO₃ shows that the Pt particles with mean diameters of 80–100 nm were on the surface of the WO₃ powder. The Pt/WO₃ showed coloration for 13% cyclohexane at higher 100 °C and for 1.3% cyclohexane at 200 °C. The in-situ XRD results of the Pt/WO₃ in coloring/bleaching change indicate that the coloring of Pt/WO₃ was caused by transformation of WO₃ to tungsten bronze. The analysis of reacted gas demonstrates that Pt on WO₃ produces only hydrogen and benzene through dehydrogenation of cyclohexane over 100 °C. It was founded that the Pt/WO₃ has potential of optical detection of organic hydrides by heating at higher 100 °C.     

Experimental investigation of flame spreading over pure methane hydrate in a laminar boundary layer

Flame spreading over pure methane hydrate in a laminar boundary layer is investigated experimentally. The free stream velocity (U_∞) was set constant at 0.4 m/s and the surface temperature of the hydrate at the ignition (T_s) was varied between ?10 and ?80 °C. Hydrate particle sizes were smaller than 0.5 mm. Two types of flame spreading were observed; “low speed flame spreading” and “high speed flame spreading”. The low speed flame spreading was observed at low temperature conditions (T_s = ?80 to ?60 °C) and temperatures in which anomalous self-preservation took place (T_s = ?30 to ?10 °C). In this case, the heat transfer from the leading flame edge to the hydrate surface plays a key role for flame spreading. The high speed flame spreading was observed when T_s = ?50 and ?40 °C. At these temperatures, the dissociation of hydrate took place and the methane gas was released from the hydrate to form a thin mixed layer of methane and air with a high concentration gradient over the hydrate. The leading flame edge spread in this premixed gas at a spread speed much higher than laminar burning velocity, mainly due to the effect of burnt gas expansion.     

Flame chemistry of tetrahydropyran as a model heteroatomic biofuel

The flame chemistry of tetrahydropyran (THP), a cyclic ether, has been examined using vacuum-ultraviolet (VUV)-photoionization molecular-beam mass spectrometry (PI-MBMS) and flame modeling, motivated by the need to understand and predict the combustion of oxygen-containing, biomass-derived fuels. Species identifications and mole-fraction profiles are presented for a fuel-rich (Φ = 1.75), laminar premixed THP–oxygen–argon flame at 2.66 kPa (20.0 Torr). Flame species with up to six heavy atoms have been detected. A detailed reaction set was developed for THP combustion that captures relevant features of the THP flame quite well, allowing analysis of the dominant kinetic pathways for THP combustion. Necessary rate coefficients and transport parameters were calculated or were estimated by analogies with a recent reaction set [Li et al., Combust. Flame 158 (2011) 2077–2089], and necessary thermochemical properties were computed using the CBS-QB3 method. Our results show that under the low-pressure conditions, THP destruction is dominated by H-abstraction, and the three resulting THP-yl radicals decompose primarily by β-scissions to two- and four-heavy-atom species that are generally destroyed by β-scission, abstraction, or oxidation.     

Growth mode of Pt1−xNix films biased dc-sputter-deposited on MgO(0 0 1)

A study is made by TEM, XRD and by measuring electrical/magnetic properties, of growth mode and properties of Pt_1−xNi_x alloy films deposited on MgO(0 0 1) at 250°C by dc-sputtering at 2.5–2.7 kV in Ar. A bias voltage V_s≤−160 V was applied to the substrate during deposition. It was confirmed that the Pt film was polycrystalline with the texture of Pt(1 1 1)/MgO(0 0 1) while the films of Pt_0.14Ni_0.86 and Pt_0.19Ni_0.81 were epitaxially grown with Pt–Ni(0 0 1)[1 0 0]/MgO(0 0 1)[1 0 0] similarly to the case of Ni/MgO(0 0 1). Thus the growth mode transformation between Pt–Ni(1 1 1)/MgO(0 0 1) and Pt–Ni(0 0 1)/MgO(0 0 1) may be induced at x less than 0.81 for Pt_1−xNi_x alloy films. The temperature coefficient of resistance TCR from 100 to 300 K of Pt_0.14Ni_0.86 films was estimated to be 0.0044–0.0053 K⁻¹ and saturation magnetization at 300 K to be 1.7–3.2 kG, respectively, while TCR of Pt films was estimated to be 0.0035–0.0048 K⁻¹.     

Thermal and sonochemical synthesis of porous (Ce,Zr)O2 mixed oxides from metal β-diketonate precursors and their catalytic activity in wet air oxidation process of formic acid

Porous (Ce_0.5Zr_0.5)O₂ solid solutions were prepared by thermolysis (T = 285 °C) or sonolysis (20 kHz, I = 32 W cm⁻², P_ac = 0.46 W mL⁻¹, T = 200 °C) of Ce(III) and Zr(IV) acetylacetonates in oleylamine or hexadecylamine under argon followed by heat treatment of the precipitates obtained in air at 450 °C. Transmission Electron Microscopy images of the samples show nanoparticles of ca. 4–6 nm for the two synthetic approaches. The powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray and μ-Raman spectroscopy of solids obtained after heat treatment indicate the formation of (Ce_0.5Zr_0.5)O₂ solid solutions with a metastable tetragonal crystal structure for the two synthetic routes. The specific surface area of the samples varies between 78 and 149 m² g⁻¹ depending on synthesis conditions. The use of Barrett–Joyner–Halenda and t-plot methods reveal the formation of mixed oxides with a hybrid morphology that combines mesoporosity and microporosity regardless of the method of preparation. Platinum nanoparticles were deposited on the surface of the mixed oxides by sonochemical reduction of Pt(IV). It was found that the materials prepared by sonochemistry exhibit better resistance to dissolution during the deposition process of platinum. X-ray photoelectron spectroscopy analysis shows the presence of Pt(0) and Pt(II) on the surface of mixed oxides. Porous (Ce_0.5Zr_0.5)O₂ mixed oxides loaded with 1.5 %wt. platinum exhibit high activity in catalytic wet air oxidation of formic acid at 40 °C.     

Flame spread along a thin solid randomly distributed combustible and noncombustible areas

Flame spread route in fire strongly depends on distribution of combustible materials. Two types of scenario are considered in flame spread when combustible materials randomly distributed; one case is that flame spreads and combustible materials burn out, and the other case is that flame self-extinguishes on the way. The threshold of burning out or self-extinguishing may be determined by quantity of combustible materials and their placement in space. Our objectives are to clarify the characteristics and threshold of flame spread. In this paper, we examine non-uniform flame spread in open air along a thin combustible solid with randomly distributed pores, which are considered as noncombustible space. Experimental results show that the flame spread rate for S ≦ 1 (S ≡ d/L_h, S: scale ratio, d: pore-scale, L_h: pre-heat length ahead of flame leading edge measured by using a shadowgraph method) increases with increasing the porosity and reaches maximum value approximately at 20–30% of porosity, while the flame spread rate for S > 1 is almost constant. Over 40% of porosity, the flame spread rate for both S ≦ 1 and S > 1 decreases. The flame cannot spread and completely self-extinguish over 60% of porosity independently with pore-scale and shape. The threshold of flame spread is related with the average-number of slit, N_s, which is made by connecting each pores. The N_s as the threshold of flame spread is unity for S > 1, while the modified average-number of slit (N_s × S) becomes two for S ≦ 1.     

Promotion effect of Pt on a SnO2–WO3 material for NOx sensing

Metal-oxide nanocomposites were prepared over screen-printed gold electrodes to be used as room-temperature NO_x (nitric-oxide (NO) and nitrogen dioxide (NO₂)) sensors. Various weight ratios of SnO₂–WO₃ and Pt loadings were used for NO sensing. The sensing materials were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface analysis. The NO-sensing results indicated that SnO₂–WO₃ (1:2) was more effective than other materials were. The sensor response (S=resistance of N₂/resistance of NO=R_N2/R_NO) for detecting 1000 ppm of NO at room temperature was 2.6. The response time (T₉₀) and recovery time (TR₉₀) was 40 s and 86 s, respectively. By further loading with 0.5% Pt, the sensor response increased to 3.3. The response and recovery times of 0.5% Pt/SnO₂–WO₃ (1:2) were 40 s and 206 s, respectively. The linearity of the sensor response for a NO concentration range of 10–1000 ppm was 0.9729. A mechanism involving Pt promotion of the SnO₂–WO₃ heterojunction was proposed for NO adsorption, surface reaction, and adsorbed NO₂ desorption.     

Growth-induced perpendicular magnetic anisotropy and clustering in NixPt1−x alloys

Polycrystalline and epitaxial (1 0 0), (1 1 0), and (1 1 1)-oriented Ni₃Pt, NiPt, and NiPt₃ films were deposited over a range of growth temperatures from 80°C to 700°C. Films grown at moderate temperatures (200–400°C) exhibit growth-induced properties similar to Co–Pt alloys: enhanced and broadened Curie temperature, perpendicular magnetic anisotropy and large coercivity. As in Co–Pt, the magnetic properties suggest a clustering of Ni into platelets on the growth surface, as the films are being grown. Unlike Co–Pt, however, NiPt films exhibit a strong orientational dependence of anisotropy and enhanced Curie temperature, possibly resulting from different types of surface reconstructions which affect the growth surface.     

Large spontaneous Hall angle in [Co,CoFe/Pt] multilayer

We have quantitatively investigated the Hall effect in [Co, CoFe/Pt] multilayer films. The [Co, CoFe/Pt] multilayers exhibit large spontaneous Hall resistivity (ρ_H) and Hall angle (ρ_H/ρ). Even though the Hall resistivity in [Co, CoFe/Pt] multilayer films (2.7–4 × 10⁻⁷ Ω cm) is smaller than that of amorphous RE–TM alloy films which show large spontaneous Hall resistivity (<2 × 10⁻⁶ Ω cm), the Hall angle of multilayer (6–8%) is almost twice than that in amorphous rare earth–transition metal alloy films (∼3%). The Hall angle provides evidence of the effects of the exchange interaction of the Hall scattering. The exchange is between conduction electron spins and the localized spins of the transition metal. The large Hall angle of [Co, CoFe/Pt] multilayer can be considered due to the high spin polarization and high Curie temperature of Co and CoFe transition metal layers. Even though the role of interfaces and surfaces in the magnetic properties of multilayer films may dominate that of the bulk, the Hall effects in [Co, CoFe/Pt] multilayer may be mainly dominated by the bulk effect.     

An experimental study on the formation of polycyclic aromatic hydrocarbons in laminar coflow non-premixed methane/air flames doped with four isomeric butanols

Experimental measurements were conducted for temperatures and mole fractions of C1–C16 combustion intermediates in laminar coflow non-premixed methane/air flames doped with 3.9% (in volume) 1-butanol, 2-butanol, iso-butanol and tert-butanol, respectively. Synchrotron vacuum ultraviolet photoionization mass spectrometry (SVUV-PIMS) technique was utilized in the measurements of species mole fractions. The results show that the variant molecular structures of butyl alcohols have led to different efficiencies in the formation of polycyclic aromatic hydrocarbons (PAHs) that may cause the variations in sooting tendency. Detailed species information suggests that the presence of allene and propyne promotes benzene formation through the C₃H₃ + C₃H₄ reactions and consequently PAH formation through the additions of C2 and C3 species to benzyl or phenyl radicals. As a matter of fact, PAHs formed from the 1-butanol doped flame are the lowest among the four investigated flames, because 1-butanol mainly decomposes to ethylene and oxygenates rather than C3 hydrocarbon species. Meanwhile, the tert-butanol doped flame generates the largest quantities of allene and propyne among the four flames and therefore is the sootiest one.     

Preparation of zeolite nanorods by corona discharge plasma for degradation of phenazopyridine by heterogeneous sono-Fenton-like process

The plasma-modified clinoptilolite (PMC) nanorods were prepared from natural clinoptilolite (NC) utilizing environmentally-friendly corona discharge plasma. The PMC and NC were characterized by XRD, FT-IR, SEM, EDX, XPS and BET, which confirmed the nanocatalyst formation. The catalytic performance of the PMC in the heterogeneous sono-Fenton-like process was greater than the NC for treatment of phenazopyridine (PhP). The desired amounts were obtained for experimental parameters including initial pH (5), PMC dosage (2 g/L), K₂S₂O₈ concentration (2 mmol/L), ultrasonic power (300 W) and PhP concentration (10 mg/L). Reactive oxygen species scavengers decreased the removal efficiency of the PhP. The treatment process followed pseudo-first order kinetic and seven degradation intermediates were identified by the GC–MS technique.     

Degradation of ibuprofen by hydrodynamic cavitation: Reaction pathways and effect of operational parameters

Ibuprofen (IBP) is an anti-inflammatory drug whose residues can be found worldwide in natural water bodies resulting in harmful effects to aquatic species even at low concentrations. This paper deals with the degradation of IBP in water by hydrodynamic cavitation in a convergent–divergent nozzle. Over 60% of ibuprofen was degraded in 60 min with an electrical energy per order (E_EO) of 10.77 kWh m⁻³ at an initial concentration of 200 μg L⁻¹ and a relative inlet pressure p_in = 0.35 MPa. Five intermediates generated from different hydroxylation reactions were identified; the potential mechanisms of degradation were sketched and discussed. The reaction pathways recognized are in line with the relevant literature, both experimental and theoretical. By varying the pressure upstream the constriction, different degradation rates were observed. This effect was discussed according to a numerical simulation of the hydroxyl radical production identifying a clear correspondence between the maximum kinetic constant k_OH and the maximum calculated OH production. Furthermore, in the investigated experimental conditions, the pH parameter was found not to affect the extent of degradation; this peculiar feature agrees with a recently published kinetic insight and has been explained in the light of the intermediates of the different reaction pathways.     

Ferroelectric polarization and resistive switching characteristics of ion beam assisted sputter deposited BaTiO3 thin films

In this work, 150 nm thick polycrystalline BaTiO₃ (BTO) films were deposited on Pt/TiO₂/SiO₂/Si substrate by ion beam assisted sputter deposition technique. The bias voltage dependent resistive switching (RS) and ferroelectric polarization characteristics of Au/BTO/Pt devices are investigated. The devices display the stable bipolar RS characteristics without an initial electroforming process. Fittings to current–voltage (I–V) curves suggest that low and high resistance states are governed, respectively, by filamentary model and trap controlled space charge limited conduction mechanism, where the oxygen vacancies act as traps. Presence of oxygen vacancies is evidenced from the photoluminescence spectrum. The devices also display P–V loops with remnant polarization (P_r) of 5.7 μC/cm² and a coercive electric field (E_c) of 173.0 kV/cm. The coupling between the ferroelectric polarization and RS effect in BTO films is demonstrated.     

H2 splitting on Pt,Ru and Rh nanoparticles supported on sputtered HOPG

The equilibrium hydrogen exchange rate between adsorbed and gas phase hydrogen at 1 bar is measured for Pt, Ru and Rh nanoparticles supported on a sputtered HOPG substrate. The particles are prepared by Electron Beam Physical Vapor Deposition and the diameter of the particles varies between 2 and 5 nm. The rate of hydrogen exchange is measured in the temperature range 40–200 °C at 1 bar, by utilization of the H–D exchange reaction. We find that the rate of hydrogen exchange increases with the particle diameter for all the metals, and that the rate for Ru and Rh is higher than for Pt. In the case of Pt, the equilibrium dissociative sticking probability, S, is found to be nearly independent of particle diameter. For Ru and Rh, S is found to depend strongly on particle diameter, with the larger particles being more active. The apparent energy of desorption at equilibrium, E_app, shows a dramatic increase with decreasing particle diameter for diameters below 5 nm for Ru and Rh, whereas E_app is only weakly dependent on particle diameter for Pt. We suggest that the strong variation in the apparent desorption energy with particle diameter for Ru and Rh is due to the formation of compressed hydrogen adlayers on the terraces of the larger particles. Experiments are also carried out in the presence of 10 ppm CO. Pt is found to be very sensitive to CO poisoning and the H–D exchange rate drops below the detection limit when CO is added to the gas mixture. In the case of Ru and Rh nanoparticles, CO decreases the splitting rate significantly, also at 200 °C. The variation of the sensitivity to CO poisoning with particle diameter for Ru and Rh is found to be weak.     

Superconductivity of the platinum doped 122 iron arsenide SrFe2−xPtxAs2

Pt doped 122 iron arsenide SrFe_1?xPt_xAs₂ (0 ? x ? 0.4) was successfully synthesized. The tetragonal unit-cell volume and the lattice constant a increase with increasing the Pt content, while c decreases, suggesting that the Fe ions are indeed replaced by Pt ions. By the Pt doping, the magnetic order of the parent phase is suppressed, and superconductivity emerges at approximately x = 0.15. T_c reaches the maximum of 16 K at x = 0.2. The compounds series can be a suitable subject to investigate role of the doped 5d state in the superconducting 3d Fe–As layer.     

Stabilized flames in hybrid aluminum-methane-air mixtures

A premixed methane–air bunsen-type flame is seeded with micron-sized (d₃₂ = 5.6 μm) atomized aluminum powder over a wide range of solid fuel concentrations. The burning velocities of the resulting two-phase hybrid flame are determined using the total surface area of the inner flame cone and the known volumetric flow rate, and spatially resolved flame spectra are obtained with a spectral scanning system. Flame temperatures are derived through polychromatic fitting of Planck’s law to the continuous part of the spectrum. It is found that an increase in the solid fuel concentration changes the aluminum combustion regime from low temperature oxidation to full-fledged flame front propagation. For stoichiometric methane–air mixtures, the transition occurs in the aluminum concentration range of 140–220 g/m³ and is manifested by the appearance of AlO sub-oxide bands and an increase in the flame temperature to 2500 K. The flame burning velocity is found to decrease only slightly with an increase in aluminum concentration, in contrast to the rapid decrease in flame speed, followed by quenching, that is observed for flames seeded with inert SiC particles. The observed behavior of the burning velocity and flame temperature leads to the conclusion that intense aluminum combustion in a hybrid flame only occurs when the flame front propagating through the aluminum suspension is coupled to the methane–air flame.     

Structural dependence of intermediate species for the hydrogen evolution reaction on single crystal electrodes of Pt

Adsorbed hydrogen and water were measured during the hydrogen evolution reaction (HER) on the low and high index planes of Pt in 0.5 M H₂SO₄ using infrared reflection absorption spectroscopy. Hydrogen is adsorbed at the atop site (atop H) on Pt(110) during the HER, whereas adsorbed hydrogen at the asymmetric bridge site (bridge H) is found on Pt(100). The band intensity of the adsorbed hydrogen depends on temperature, indicating that the bands are due to the intermediate species for the HER. The band of the atop H appears on stepped surfaces with (110) step, whereas the asymmetric bridge H is observed on Pt(211) = 3(111)–(100) and Pt(311) = 2(111)–(100) that have (100) step. The absence of the atop H on Pt(100), Pt(211), and Pt(311) can be attributed to the relative stability of the bridge site.     

Surface properties of palladium catalysts supported on ternary ZrO2–Al2O3–WOx oxides prepared by the sol–gel method: Study of the chemical state of the support

The surface properties of Pd and Pd–Pt catalysts supported on binary ZrO₂–WOx and ternary ZrO₂–Al₂O₃–WOx oxides prepared by the sol–gel method were studied. Special attention was paid to the study of the texture of the catalysts as well as the chemical state of tungstated zirconia and tungstated zirconia promoted with alumina in the palladium catalysts. The catalysts were tested in the isomerization of n-hexane and were characterized by N₂ physisorption, XRD, TPR, Raman spectroscopy, XPS and FT-IR of adsorbed pyridine. The catalysts had bimodal pore size distributions with mesopores in the range 55–70 Å and macropores of 1000 Å in diameter. The catalysts had a surface WOx coverage (4.4–6.0 W nm^?2) lower than that of the theoretical monolayer (7.0 W nm^?2). A lower acidity of the ternary ZrO₂–Al₂O₃–WOx oxide as compared to the binary ZrO₂–WOx oxide was found. Higher activity in the isomerisation of n-hexane was obtained in the Pd–Pt catalysts supported on ternary ZrAlW oxides prepared by sol–gel that is correlated with the coexistence on the surface of W⁴⁺ (WO₂) or W⁰ and W⁶⁺ (Al₂(WO₄)₃) species, ZrO₂ in the tetragonal phase and a high amount of ZrOx suboxides species in a low oxidation state (Zr³⁺ and Zr²⁺).     

An X-ray photoelectron spectroscopy investigation of a novel Pd–Pt colloid catalyst

A Bi-promoted charcoal-supported Pd–Pt oxidation catalyst prepared from colloidal NOct₄Cl-stabilized Pd–Pt nanoparticles was investigated by means of X-ray photoelectron spectroscopy (XPS). Pd 3d, Pt 4f, Bi 4f, C 1s and O 1s spectra of the colloid, the supported colloid catalyst and a conventional charcoal-supported Pd–Pt/Bi coimpregnation catalyst (Degussa, CEF 196 RA/W) were measured. Both catalysts were explored unused (as-prepared) and after deactivation in the heterogeneous catalytic oxidation of glucose to gluconic acid. The spectra are analyzed to elucidate the higher starting activity of the Pd–Pt/Bi/C colloid catalyst, especially the role of the promotor Bi and the mechanisms leading to catalyst deactivation. The higher starting activity of the colloid catalyst is explained by the presence of completely reduced Pd and Pt, threevalent Bi and a smaller particle size in contrast to the conventional catalyst which contains partly oxidized Pd and a non-unique chemical state of Bi. The deactivation of both catalysts is suggested to be due to metal dissolution, particle growth and chemical poisoning.     

Size dependence of ground-state energy of the excitons in spherical Y2O3

The exciton energies of rare earth oxides (Ln₂O₃) have rarely been calculated by the theory. Experimentally, the blue-shift of exciton energy in nanocrystals deviates from the traditional size confinement effect. Herein, the dependence of the ground-state energy of an exciton in Y₂O₃ spheres on particle radius was calculated by using a variational method. In the model, an exciton confined in a sphere surrounded by a dielectric continuum shell was considered. The ground-state energy of exciton comprises kinetic energy, coulomb energy, polarization energy and exciton–phonon interaction energy. The kinetic and coulomb energy were considered by the effective mass and the dielectric continuum and the exciton–phonon interaction energy was given by the intermediate coupling method. The numerical results demonstrate that the present model is roughly consistent with the experimental results. The confinement effect of the kinetic energy is dominant of the blue-shift of the exciton energy in the region of R < 5 nm, while confinement effect of the coulomb energy is dominant of the blue-shift of the exciton energy in the region of R > 5 nm. The polarization energy contributes largely to the exciton energy as the particle size is smaller than ~ 10 nm, while the exciton–phonon interaction energy takes only a little contribution in all the range.