草酸钴原位催化高氯酸铵热分解的DSC／TG-MS研究

采用差示扫描量热/热分析-质谱(DSC/TG-MS)联用技术研究了草酸钴对高氯酸铵的原位催化. 结果表明,草酸钴原位分解生成的钴氧化物对高氯酸铵有较强的催化作用,添加2%的草酸钴使高氯酸铵的分解温度降低104 ℃, 分解放热量从655 J/g增大到 1 469 J/g. 分解的气相产物主要有H2O, NH3,O2,HCl,Cl2,NO,N2O和NO2. 由于氧在新生态的纳米钴氧化物表面形成过氧化活性离子(O-2), 使氨氧化在钴氧化物的过氧化表面活性中心进行,加速了高氯酸铵的热分解,使其表观放热量大幅度增加.     

纳米NdCoO3催化高氯酸铵热分解的DSC/TG-MS研究

采用微乳液法制备了立方晶系的NdCoO3纳米晶.利用DSC/TG-MS研究了NdCoO3对AP热分解的催化作用.结果表明,在NdCoO3的催化作用下,AP的热分解反应峰值温度下降了113℃,表观分解反应热从655 J·g-1增加到1 363 J·g-1,分解的气相产物主要有NH3,H2O,O2,HCl,N2O,NO,NO2和Cl2.在金属氧化物表面吸附生成超氧化离子(O2-)和氧离子(O-,O2-),这是加速AP分解反应的主要原因.加入NdCoO3催化AP热分解,由于对氨的氧化深度不同而导致分解放热量的增加.     

纳米铜粉对高氯酸铵热分解的影响

The decomposition behaviour of ammonium perchlorate (AP) has been investigated in the presence of Cu nanopowder by DTA. The results show that nanometer Cu powder decreased the first and second thermal decomposition temperature of AP by 35.1 ℃ and 130.2 ℃, respectively, and the DTA heat release of AP in the presence of Cu nanopowders increased to 1.20 kJ·g^-1, showing good catalytic effect on the thermal decomposition of AP. The catalytic effect of Cu micron-size powder on the thermal decomposition of AP was less than that of Cu nanopowder. With the increase in content, Cu nanopowder enhanced its catalytic effect on the high temperature decomposition of AP, however, it weakened its catalytic effect on the low temperature decomposition of AP. The mechanism of catalysis for the thermal decomposition of AP is as follows: (1) metal oxider acts as the intermedium in the process of election tranfer, (2) Cu nanopowder reacts with the decomposed product of AP, (3) Cu nanopowder has special surface effect.     

铜/纳米金刚石复合物的结构及其对高氯酸铵热分解的催化作用

Nano-Copper and Cu/UDD (ultradispersed diamond) nanocomposites were separately prepared by reduction of CuCl₂ aqueous solution and that doped with 0.7%(weight percent) of ultra-dispersed diamond. The as prepared nano-crystals were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FTIR) and electron paramagnetic resonance techniques (EPR). It was found that homogeneous nucleation dominated the aqueous reduction reaction at high concentration and the diameter of nano-copper decreased as the reaction time shortened, yet at lower concentration heterogeneous nucleation predominated and the doped UDD functioned as heterogeneous nucleation. Otherwise large number of free-radicals existed in the nano-composites. Both of nano-copper and Cu/UDD nanocomposites were strong catalysts for AP decomposition, with Cu/UDD being a more effective one. The higher decomposition temperature for AP was 119 ℃ lower than that without catalyst. And the exothermic quantity of decomposition was from 590 J·g^-1 to 1 400 J·g^-1 by mix 2% of the Cu/UDD nanocomposites.     

纳米金属粉对高氯酸铵热分解特性的影响

催化性能;纳米金属粉对高氯酸铵热分解特性的影响     

含铜类水滑石催化材料热分解过程的研究

共沉淀法合成了Cu0.13Mg0 6Al0.27(OH)2(CO3)0.135·xH2O类水滑石物质 (CuHTlc) ,采用XRD、DTA TG、BET、TEM和27AlMASNMR技术对其热分解过程进行了表征。结果表明 ,在较低焙烧温度时 (低于300℃ ),氢氧根和层间水部分脱除 ,但水滑石仍保持其层状结构 ;500℃时 ,其层状结构被完全破坏 ,出现氧化镁晶相结构 ,随着焙烧温度的进一步升高 ,尖晶石晶相生成。500℃时的焙烧产物具有最大比表面 (193m2·g-1)。当温度高于500℃ ,焙烧产物组成可表示为Cu0.13Mg0.6Al0.27O0.135,CuHTlc的热分解过程可表示为 :Cu0.13Mg0.6Al0.27(OH)2(CO3)0.135·xH2O→Cu0.13Mg0.6Al0.27O0.135 (1 x)H2O 0.135CO2。     

纳米Cu2O的制备及其对高氯酸铵热分解的催化性能

 以Cu(NO3)2和NaOH为原料,以水合肼为还原剂,通过沉淀法在室温下制备了纳米Cu2O. 采用X射线衍射、透射电镜和X射线光电子能谱等手段对产物进行了表征,并用热分析法考察了不同形貌的纳米Cu2O对高氯酸铵热分解的催化作用. 结果表明,通过改变NaOH溶液的加入量可分别得到长针形和多边形的纳米Cu2O. 通过调节反应物浓度可以将纳米Cu2O粒径控制在19～68 nm. 不同形貌的纳米Cu2O均能强烈催化高氯酸铵的热分解,其中分散性良好的多边形纳米Cu2O的催化活性较高,添加2%的多边形纳米Cu2O可使高氯酸铵的高温分解温度降低103 ℃,分解放热量由590 J/g增至1350 J/g.     

不同粒度高氯酸铵的热分解研究

利用高压差示扫描量热法(PDSC), 热重法(TG), 固体原位红外联用法(Thermolysis/RSFT-IR)和热分析与质谱和红外联用法(Thermal analysis-MS-FTIR)研究了不同粒度高氯酸铵AP在1.0 MPa压强下和常压下的热分解过程, 提出了不同粒度AP可能的热分解机理. 研究结果表明, 不同粒度AP的高压和常压下的热分解历程存在明显的差异, 较大粒度AP的受热分解过程中存在明显的低温分解阶段和高温分解阶段, 小粒度的AP则仅存在明显的高温分解阶段. AP的分解气体产物主要包括NO2, NO, N2O, O2, H2O和HCl.     

铝粉粒度对高氯酸铵热分解动力学的影响

采用热重-差示扫描量热(TG-DSC)联合技术研究了10.7 μm, 2.6 μm和40 nm铝粉对高氯酸铵(AP)热分解的影响. 结果表明, 铝粉的加入对AP的低温放热峰有抑制作用, 对高温放热分解反应有促进作用, 并且随铝含量的增加和铝粒径的减小这种作用更强烈. 采用多元非线性拟合技术对不同升温速率下TG-DSC实验数据进行拟合, 结果表明, 质量分数为40%的不同粒径铝粉的加入对AP的热分解三阶段(A→B→C→D)反应模型无影响, 但反应机理函数发生了改变. 纯AP, AP/Al(10.7 μm), AP/Al(2.6 μm)及AP/Al(40 nm)的反应机理函数组合分别为C1/D1/D1, C1/D1/D3, C1/D1/D4和C1/D1/F2.     

纳米Co3O4的制备及其对高氯酸铵热分解的催化性能

 选用CoCl2·6H2O分别与NaOH, H2C2O4·2H2O, Na2CO3·10H2O及Na2C2O4组成四个反应体系,通过室温固相反应制备了不同平均粒径的纳米Co3O4, 并用X射线衍射和透射电镜对Co3O4的物相、形貌和粒径大小进行了表征. 结果表明, Co3O4的平均粒径分别为23, 30, 35和150 nm, 大小均匀,分散性好. 还用差热分析法考察了纳米Co3O4对高氯酸铵热分解的催化性能,并与微米Co3O4进行了比较. 结果表明,纳米Co3O4可使高氯酸铵的低温放热峰消失,高温放热峰温度降至323.5 ℃, 降低了128.5 ℃, 表观分解热增加了750 J/g, 达 1265 J/g, 纳米Co3O4对高氯酸铵热分解的催化性能明显好于微米Co3O4.     

Preparation of Ni/TiO2 Nanoparticles and Their Catalytic Performance on the Thermal Decomposition of Ammonium Perchlorate

Metal/oxide nanoparticles are attractive because of their special structure and better properties. The Ni/TiO₂ nanoparticles were prepared by a liquid phase chemical reduction method in this paper. The obtained‐products were characterized by inductively coupled plasma (ICP), X‐ray diffraction (XRD), high‐resolution transmission electron microscopy (HRTEM) and scanning electron microscopy (SEM). The results show that Ni particles in Ni/TiO₂ nanoparticles exhibit better dispersion and the size of most Ni particles is 10 nm or so. The catalytic activity of Ni/TiO₂ nanoparticles on the thermal decomposition of ammonium perchlorate (AP) was investigated by simultaneous thermogravimetry and differential thermal analysis (TG‐DTA). Results show that composite process of Ni and TiO₂ can improve the catalytic activity of Ni nanoparticles on the thermal decomposition of AP, which is mainly attributed to the improvement of Ni dispersion in Ni/TiO₂ nanoparticles. The catalytic activity of Ni/TiO₂ nanoparticles increases with increasing the weight ratio of Ni to AP.     

钛酸锌的制备及其对高氯酸铵热分解的催化性能

ZnTiO₃ nanocrystals were prepared by sol-gel method, using Zn(NO₃)₂ and Ti(C₄H₉O)₄ in the topic. The as-prepared ZnTiO₃ nanocrystals were characterized by XRD, FTIR and TEM, and the catalytic performance of ZnTiO₃ nanocrystals of different contents for the ammonium perchlorate(AP)decomposition was investigated by thermal analysis. The results indicate that ZnTiO₃ with pure cube structure can be synthesized at 600 ℃ by this procedure,which was spheroid with particle size of about 60~100 nm. The results expressed that the low temperature decomposition peaks of AP is advanced by 17 ℃ and the high temperature decomposition peaks of AP is advanced by 24 ℃ when adding 5% nanoparticle ZnTiO₃ powder. The catalytic effects of ZnTiO₃ powders on the high temperature decomposition of AP are less than that of nanometer metal powders, but all the micron metal powders decrease the low decomposition temperature of AP.     

Enhanced Thermal Decomposition Properties and Catalytic Mechanism of Ammonium Perchlorate over CuO/MoS2 Composite

In this report, CuO/MoS₂ composites were successfully prepared by the hydrothermal method where nano‐sized CuO was uniformly distributed on the surface of hierarchical MoS₂ substrates (CuO/MoS₂ composites). Their physicochemical properties and catalytic performance in ammonium perchlorate (AP) decomposition were investigated and characterized by XRD, SEM, TEM, BET, XPS, TG/DSC and combustion measurement. The results showed that it could decrease AP decomposition temperature at high decomposition stage from 416.5 °C to 323.5 °C and increase the heat release from 378 J/g (pure AP) to 1340 J/g (AP with catalysts), which was better than pure CuO nanoparticles (345.5 °C and 1046 J/g). Meanwhile, it showed excellent performance in combustion reaction either in N₂ or air atmosphere. The results obtained by photocurrent spectra, photoluminescence spectra and time‐resolved fluorescence emission spectra indicated that loading CuO mediated the generation rate and combination rate of electrons and holes, thus tuning the catalytic performance on AP decomposition. This study proved that employing the supports that can synergistically interact with CuO is an efficient strategy to enhance the catalytic performance of CuO.     

纳米结晶体Ni0.5Zn0.5Fe2O4对高氯酸铵热行为及分解反应动力学的影响

采用差示扫描量热法(DSC)、热重和微分热重(TG-DTG)及固相原位反应池/快速扫描傅立叶变换红外联用技术(hyphenated in situ thermolysis/RSFTIR)研究了纳米结晶体Ni_0.5Zn_0.5Fe₂O₄与高氯酸铵(AP)组成的混合物的热行为和分解反应动力学。结果表明：Ni_0.5Zn_0.5Fe₂O₄使得AP的低、高温分解放热峰温分别提前17.44 K和27.74 K,并使得对应的分解热分别增加3.7 J·g^-1和193.7 J·g^-1。Ni_0.5Zn_0.5Fe₂O₄并不影响AP的晶转温度和晶转热。Ni_0.5Zn_0.5Fe₂O₄使得AP的TG曲线出现3个阶段,并使得后2个失重阶段的初始和终止温度都有所提前。凝聚相分解产物分析表明Ni_0.5Zn_0.5Fe₂O₄加速了凝聚相AP的分解及氨气的释放。含Ni_0.5Zn_0.5Fe₂O₄的AP的高温分解反应的动力学参数E_a=238.88 kJ·mol^-1,A=1018.59 s^-1,动力学方程可表示为dα/dt=10^18.99(1-α)[-ln(1-α)]^3/5e^-2.87×104T。始点温度(T_e)和峰顶温度(T_p)计算得出AP的热爆炸临界温度值分别为:574.83 K和595.41 K。分解反应的活化熵(ΔS^≠)、活化焓(ΔH^≠)和活化能(ΔG^≠)分别为:109.61 J·mol^-1·K^-1、236.49 kJ·mol^-1及172.58 kJ·mol^-1。     

Cu/Co/Fe水滑石衍生的复合氧化物催化高氯酸铵热分解的研究

以Cu/Co/Fe水滑石(Cu/Co/Fe-LDHs)为前驱体经过焙烧制备了Cu/Co/Fe复合氧化物(Cu/Co/Fe-MOs)。利用DTA和TG-MS研究了Cu/Co/Fe-MOs作为新型催化剂对高氯酸铵热分解的催化性能。结果表明,Cu/Co/Fe-MOs呈现为CuFe2O4和(CoFe2)O4晶相,具有70~110 m2.g-1的比表面积。晶粒大小均匀,尺寸在20~30 nm。添加4wt%的400℃焙烧得到的Cu/Co/Fe-MOs催化剂使高氯酸铵热分解反应的温度降低了139℃。Cu/Co/Fe-MOs是通过吸附在金属氧化物表面的超氧离子(O2-)来加速高氯酸铵热分解的。     

纳米Fe2O3的制备及其对高氯酸铵热分解的催化性能

 用两相体系方法制备了纳米Fe2O3，并用X射线衍射、红外光谱和粒度分析对其结构进行了表征．结果表明，当有机溶胶的pH＝6，油酸与Fe3＋的摩尔比为1∶3．5时，Fe（OH）3在油相中的萃取率可高达90％，将有机溶胶在120℃回流8h后可得到非晶态、窄粒度分布的纳米Fe2O3粒子，其粒径在12nm左右．分别采用恒容燃烧热和差热分析研究了纳米Fe2O3对高氯酸铵热分解的催化性能．结果表明，在模拟固体推进剂中分别加入4．7％微米Fe2O3和4．7％纳米Fe2O3后，恒容燃烧热分别提高了2350．84和5095．70J／g．在高氯酸铵中加入5％微米Fe2O3可使高氯酸铵两个放热峰的出现分别提前1．10和62．25℃，而加入5％纳米Fe2O3时分别提前61．89和118．82℃，这说明纳米Fe2O3的催化活性优于微米Fe2O3．