Non-Gaussian elasticity of swollen poly(N-isopropylacrylamide) gels at high charge densities

Modulus of elasticity of highly charged N-isopropylacrylamide (NIPA) based hydrogels (PNIPA) are measured at various swelling degrees in water. The sodium salt of 2-acrylamido-2-methylpropane sulfonic acid (AMPS) was used as the ionic comonomer of NIPA in the hydrogel preparation. The mole fraction of AMPS in the comonomer feed was varied between 0 and 1, while the crosslinker ratio was fixed at 1/85. The elasticity data show that the equilibrium swollen PNIPA hydrogels are in the non-Gaussian regime. Equations were derived based on the inverse Langevin function for the swelling ratio and the modulus of highly charged PNIPA hydrogels and checked by experiments. Results of calculations show good agreement to the swelling and elasticity data of highly swollen PNIPA gels.     

Fluorescence studies on volume phase transition in poly(acrylamide) and poly(N-isopropylacrylamide) gels

The changes in microenvironments during the volume phase transition of poly(acrylamide) and poly(N-isopropylacrylamide) gels induced by pH change or the change in solvent composition were studied by using dansyl or pyrenyl fluorescent probes.     

Synthesis and phase separation of amine-functional temperature responsive copolymers based on poly(N-isopropylacrylamide)

Free radical copolymerizations of N-isopropyl acrylamide (NIPAM) and cationic N-(3-aminopropyl) methacrylamide hydrochloride (APMH) were investigated to prepare amine-functional temperature responsive copolymers. The reactivity ratios for NIPAM and APMH were evaluated in media of different ionic strength (r_NIPAM = 0.7 and r_APMH = 0.7-1.2). Phase separation behavior of the random copolymers with only 5 mol% of the APMH was found to be suppressed in pure water at temperatures up to 45 °C due to electrostatic repulsion among the cationic amine groups randomly distributed along the copolymer chain. Alternate sequential addition of PNIPAM/APMH mixtures and pure NIPAM was used to provide increased control of the location of APMH units along the chain. Consequently (close to) homo-PNIPAM block(s) were formed as evidenced by its characteristic phase transition at 33 °C. The influences of the monomer feeding time and feeding interval time to the APMH distribution were investigated to prepare copolymers with thermo-induced phase separation under physiologically relevant temperature and to determine the extent of conjugation to poly(ethylene oxide).     

Study on interaction between Tb(III) and poly(N-isopropylacrylamide)

A new kind of the thermo-sensitive and fluorescent complex of poly(N-isopropylacrylamide) (PNIPAM) and Tb(III) was synthesized by free radical polymerization, in which PNIPAM was used as a polymer ligand. The complex was characterized by using X-ray photoelectron spectroscopy (XPS), ultraviolet-visual (UV), Fourier transform infrared (FT-IR) and fluorescence spectroscopy. The results from the experiments indicated that there is a strong interaction between PNIPAM and Tb(III), leading to a decrease in the electron density of nitrogen and oxygen atoms and an increase in the electron density of Tb(III) in the PNIPAM containing Tb(III) by contrast with PNIPAM and Tb(III), respectively, meanwhile, exhibiting that the Tb(III) is mainly bonded to oxygen atoms in the polymer chain of PNIPAM and formed the complex of PNIPAM-Tb(III). After forming the PNIPAM-Tb(III) complex, the emission fluorescence intensity of Tb(III) in the PNIPAM-Tb(III) complex is significantly enhanced because the effective intramolecular energy transfer from PNIPAM to Tb(III). Especially, the emission intensity of the fluorescence peak at 547 nm can be increased as high as 145 times comparing with that of the pure Tb(III). The intramolecular energy transfer efficiency for fluorescence peak at 547 nm can reach as high as 68%. The fluorescence intensity is related the weight ratio of Tb(III) and PNIPAM in the PNIPAM-Tb(III) complex. When the weight ratio is 1.4%, the maximum fluorescence enhancement can be obtained. Nevertheless, the lower critical solution temperature of PNIPAM containing a low content of Tb(III) has not obviously changed after the formation of the complex of PNIPAM-Tb(III) by the interaction between PNIPAM and Tb(III). This novel thermosensitive and fluorescence characterization of the PNIPAM-Tb(III) complex may be useful in the fluorescence systems and the biomedical field.     

H NMR study of temperature-induced phase separation in solutions of poly(N-isopropylmethacrylamide-co-acrylamide) copolymers

¹H NMR spectroscopy was applied to investigate temperature-induced phase separation in solutions of poly(N-isopropylmethacrylamide-co-acrylamide) [P(IPMAm/AAm)] random copolymers in D₂O, D₂O/ethanol and D₂O/acetone. The NMR relaxation behaviour of water (HDO) was also examined. The effects of P(IPMAm/AAm) composition and the ethanol or acetone content in the mixed solvents on the temperature, width and extent of the phase transition as well as on the mobility of polymer segments and water molecules were characterized. For D₂O solutions of the copolymers prepared with the AAm fraction in the polymerization mixture not exceeding 25 mol% ¹H NMR spectra show dynamic heterogeneity of copolymer chains in mesoglobules where AAm sequences and surrounding short IPMAm sequences are hydrated and mobile, while sufficiently long IPMAm sequences are dehydrated and their mobility is strongly reduced. The obtained results are consistent with the idea that P(IPMAm/AAm) copolymer mesoglobules are rather porous and disordered.     

H NMR and IR study of temperature-induced phase transition of negatively charged poly(N-isopropylmethacrylamide-co-sodium methacrylate) copolymers in aqueous solutions

¹H NMR and IR spectroscopies were used to investigate the temperature-induced phase transition behaviour of poly(N-isopropylmethacrylamide-co-sodium methacrylate) [P(IPMAAm/MNa)] copolymers, containing in aqueous solutions negatively charged MNa units (i = 1-10 mol%), and the obtained results were compared with those obtained for poly(N-isopropylmethacrylamide) (PIPMAAm) homopolymer. For PIPMAAm/H₂O solution, IR spectra indicate that the transition temperatures for the hydrophilic CO groups are slightly higher (by ∼ 2 K) in comparison with hydrophobic CH₃ groups. The decreasing values of phase-separated fraction p_max and the decrescent hysteresis during gradual heating and cooling, both with increasing content of MNa units i in the copolymer, show that for copolymers with i ? 5 mol% the globular-like structures formed at temperatures above the respective LCST are rather porous and disordered with relatively low degree of polymer-polymer hydrogen bonding. While for P(IPMAAm/MNa) copolymers with i ? 5 mol% most water molecules are expelled from globular structures, for i < 5 mol% a certain portion of water (HDO) molecules is rather tightly bound in globular structures; at the same time no releasing process was detected for the bound water even for 90 h.     

Studies on copolymerization of N-isopropylacrylamide with poly(ethylene glycol) methacrylate

The paper describes the preparation and characterization of cross-linked homopolymers and copolymers of N-isopropyl acrylamide (NIPAAm) with poly(ethylene glycol) methacrylate (PEGMA, M_n = 526 g/mol). Several copolymer samples were prepared by taking varying amounts of monomers i.e. NIPAAm and PEGMA in the initial feed using hydrophilic (IRGACURE-2959) and hydrophobic (DURACURE-1173) photoinitiator. In order to investigate the effect of reaction conditions, copolymers were prepared below or above the lower critical solution temperature (LCST) using water or water:ethanol (50:50) as solvent and by varying the amounts of cross-linker. Hydrogels prepared under varying reaction conditions were characterized for its swelling behaviour (using optical microscope), phase transition temperature (using DSC) and morphology (using SEM). As expected LCST increased from 35 to 39 °C as PEGMA content in copolymers increased from 1 to 20% (w/w). However, the morphology of hydrogels was found to be independent on the reaction conditions.Copolymer films having an optimum combination of swelling and performance properties were evaluated as switchable cell culture membranes. Hepatic cancer cell lines (Hep G-2) was used to study the cell growth and detachment. Cell growth and detachment were found to be dependent on the copolymer composition. Cell viability was found comparable to trypsin which also supports application of these films as cell culture membrane.     

Fast responsive poly(N-isopropylacrylamide) hydrogels prepared in phenol aqueous solutions

Fast responsive poly(N-isopropylacrylamide) (PNIPAAm) hydrogels with improved properties were prepared in phenol aqueous solutions with different concentrations. Due to the expanded network structure in water, the resulted hydrogels are capable of absorbing a large amount of water, i.e. exhibits a much increased swelling ratio at room temperature. Importantly, the hydrogels demonstrated much faster response rate than that of traditional PNIPAAm hydrogel upon external temperature increase.     

Poly(N-isopropylacrylamide)/poly[(N-acetylimino)ethylene] thermosensitive block and graft copolymers

Block and graft copolymers with poly(N-isopropylacrylamide) and poly[(N-acetylimino)ethylene] (PNAI) sequences were synthesized via PNAI derivatives (macroinitiators or macromers). The polymerization yields for block copolymers synthesized in ethanol, using the PNAI macroinitiator, were low (<10%), except where photochemical polymerization was applied. By contrast, for the copolymerizations of N-isopropylacrylamide with the PNAI macromers, performed in alcoholic solution, quite high polymerization yields, around 80-90%, were reached. ¹H-NMR and IR spectral and differential scanning calorimeter thermal data confirmed the copolymer formation. Thermosensitivity of the copolymers was investigated by means of turbidimetric technique as a function of their nature, average molecular weight and composition. It was found that the length of the chain of the PNAI macromer and the content in hydrophilic PNAI units of the resulted copolymer affected this behavior.     

Study on interaction between Tb(III) and poly(N-isopropylacrylamide)-g-poly(N-isopropylacrylamide-co-styrene) core-shell nanoparticles

Based on the synthesis of poly(N-isopropylacrylamide-co-styrene) P(NIPAM-co-St) and poly(N-isopropylacrylamide) (PNIPAM) grafted P(NIPAM-co-St) core-shell nanoparticle, a new kind of thermoresponsive and fluorescent complex of Tb(III) and PNIPAM-g-P(NIPAM-co-St) (PNNS) was successfully prepared. The PNNS-Tb(III) complex was characterized with the different techniques. It was found that when PNNS with the core-shell structure interact with Tb(III), Tb(III) mainly bonded to O of the carbonyl groups of PNNS, forming the novel PNNS-Tb(III) complex. After forming the complex, the emission fluorescence intensity of Tb(III) in the complex is significantly enhanced. Especially, the maximum emission intensity of the PNNS-Tb(III) complex at 545 nm is enhanced about 223 times comparing to that of the pure Tb(III) because the effective intramolecular energy transfer from PNNS to Tb(III). The intramolecular energy transfer efficiency from PNNS to Tb(III) reaches 50%. The fluorescence intensity is related the weight ratio of Tb(III) and PNNS in the PNNS-Tb(III) complex. When the weight ratio of Tb(III) and the PNNS is 12 wt%, the enhancement of the emission fluorescence intensity at 545 nm is highest. This novel fluorescence characterization of the PNNS-Tb(III) complex may be useful in the fluorescence systems and the biomedical field.     

Effects of synthesis-solvent on swelling and elastic properties of poly(N-isopropylacrylamide) hydrogels

Thermosensitive N-isopropylacrylamide (NIPA) hydrogels were synthesized by a free radical copolymerization with N,N′-methylenebisacrylamide (MBAA) in four solvents: water, ethanol, acetone and N,N-dimethylformamide. The swelling and elastic properties of the hydrogels were affected by the synthesis-solvents; the hydrogels (e.g. NIPA/MBAA = 1000/50 mol/m³-pre-gel solution) synthesized in water have smaller swelling volume and larger shear modulus at 10 °C than those synthesized in amphiphilic solvents. The network structure of hydrogels was estimated in terms of the conversion and two sorts of effective crosslinking density based on the Flory theory and the concentration of crosslinker. The hydrogels synthesized in water can have the microscopic inhomogeneous network arising from the entanglement of polymer chains, while the hydrogels synthesized in amphiphilic solvents can have the homogeneous network arising from the polymer concentration lower than the pre-gel solution and can be similar in network structure to the lightly crosslinked hydrogel synthesized in water.     

Rheology of polystyrene/poly(vinyl methyl ether)blends near the phase transition

Mixtures are expected to show anomalous behavior in their viscoelastic properties close to a critical point. In this study, the reheological behavior of blends of polystyrene and poly (vinyl methyl ether) below, close to, and above the phase separation temperature T_s was investigated. Rheological measurements were carried out at three different compositions in the melt. Below and far from T_s, a satisfactory superposition of the storage and loss moduli G' and G″ was observed at all temperatures and frequencies. Close to T_s deviations were observed for G' at low frequencies (the so-called terminal zone). Above T_s G″ values was still observed over the whole range of frequencies and temperatures. The deviations observed for G' near T_s can be interpreted as due to the presence of significant concentration fluctuations. Plots of log (G'/G″²) as a function of temperature were shown to be sensitive to this anomalous behavior.     

Gradual phase transition of poly(N-isopropylacrylamide-co-acrylic acid) gel induced by electric current

The copolymer gels showing gradual phase transition induced by temperature were synthesized by redox random copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AAc) monomer under a constant electric current. The behavior of gradual phase transition induced by temperature was examined by measuring the thermal properties, pKa values and swelling ratio. The experimental results indicate that temperature-induced gradual phase transitions of poly(NIPAAm-co-AAc) gel are mainly driven by transport before polymerization and protonation/ionization of the AAc, caused by the electric current.     

Preparation of poly(N-isopropylacrylamide)-grafted polymer monolith for hydrophobic interaction chromatography of proteins

Poly(N-isopropylacrylamide)-grafted polymer monolith has been achieved using a surface-initiated atom transfer radical polymerization grafting polymerization within the pores of poly(chloromethylstyrene-divinylbenzene) macroporous monolith contained in a 100 mm × 4.6 mm I.D. stainless steel column. The grafted-poly(N-isopropylacrylamide) on the surface of the grafted monolith that was used as chromatographic stationary phase showed a response to the variation of temperatures and/or salt concentrations. This study focus on its salt concentration responsive property and it has been revealed that the hydrophobicity of the grafted monolith can be adjusted by changing salt concentrations in the range of 0.05-2.0 mol/L. A variety of salts including sodium sulfate, ammonium sulfate and sodium chloride exhibited different effects on the alteration of hydrophobicity of the grafted monolith, and the effect of the salts was in the order of sodium sulfate > ammonium sulfate > sodium chloride. Based on this response to salt concentrations, the grafted monolith was applied in hydrophobic interaction chromatography of proteins, and the base-line separation of a six proteins mixture consisting of cytochrome c, myoglobin, ribonuclease A, bovine serum albumin, ovalbumin and thyroglobulin bovine was achieved by a salt gradient elution.     

Drug permeation modeling through the thermo-sensitive membranes of poly(N-isopropylacrylamide) brushes grafted onto micro-porous films

Temperature-sensitive N-isopropylacrylamide (NIPAAm) polymer brushes of known molecular weight (20k–25k) were grafted onto micro-porous polycarbonate (PC) films (pore size 0.4 μm) using argon plasma treatment. The resulting composite membranes were tested for controlled drug release at various grafted chain density, which was controlled using 1–3% polymer concentrations. The composites were also characterized in terms of graft yield, membrane thickness, Fourier transform infrared (FTIR) spectra and scanning electron micrography (SEM). The drug permeabilities of 4-acetamidophenol and ranitidine HCl in the resulting membranes were determined at temperatures between 30 and 40 °C. The drug permeability changed remarkably at 34 °C, near the lower critical solution temperature (LCST). The drug passage was regulated by swelling (which occurs at a temperature lower than the LCST) or shrinkage (occurring at an elevated temperature) of the PNIPAAm polymer brushes. These membranes demonstrated on–off ratios of drug permeabilities up to 11 and 14 for the model drugs, respectively. These values are higher than most literature data with similar-size model molecules. The excellent on–off valve mechanism was discussed in terms of the suitable molecular weight and grafted chain density in relation to the pore size and porosity of the PC support. A mathematical model was proposed to predict the drug permeation flux based on the gel conformation data, graft density, characteristics of the micro-porous support, and drug concentrations and diffusivities in water and in the PNIPAAm gel. The model can successfully estimate the drug permeation flux through the composite with higher (0.42 mg cm⁻²) graft density with a coefficient of determination of 0.95. The discrepancy between the predicted and experimental data at the lower graft density (0.12 mg cm⁻²) was ascribed to pore channel narrowing resulting from the uneven polymer chain distribution.     

The synthesis, characterisation, phase behaviour and swelling of temperature sensitive physically crosslinked poly(1-vinyl-2-pyrrolidinone)/poly(N-isopropylacrylamide) hydrogels

Physically crosslinked complexes of polyvinyl pyrrolidinone-poly (N-isopropylacrylamide) (PVP-PNIPAAm) were prepared by photopolymerisation from a mixture of the monomers 1-vinyl-2-pyrrolidinone and N-isopropylacrylamide. IR spectroscopy and calorimetry were used to characterise the resulting xerogels. By alternating the monomer feed ratio, copolymers were synthesised to have their own distinctive lower critical solution temperature (LCST). The transition temperature of the gels was established using cloud point measurement and modulated differential scanning calorimeter (MDSC). This ability to shift the phase transition temperature of the copolymers provides excellent flexibility in tailoring transitions for specific uses. Swelling experiments were performed on the copolymer disks in distilled water at varying temperatures to establish the behaviour of the gels above and below phase transition temperature. The results obtained show that below transition temperature, the gels are water soluble but above this temperature they are slightly less water soluble; significantly less water soluble; or water insoluble; depending on the composition and LCST of the gel.     

Thermosensitive aggregates self-assembled by an asymmetric block copolymer of dendritic polyether and poly(N-isopropylacrylamide)

An asymmetric linear-dendritic block copolymer of polyether dendrimer and poly(N-isopropylacrylamide) was prepared by an atom transfer radical polymerization method. The self-assembly behavior and thermosensitive property of this copolymer in water were studied by dynamic light scattering (DLS), transmission electron microscopy (TEM) and fluorescence probe spectroscopy. It was found that the thermosensitive phase transition takes place at the temperature of 37.5 °C; simultaneously the spherical aggregates grow into larger entangled nanotubules. The unique temperature-sensitive supramolecular aggregates may make them especially useful as intelligent capsules for drug delivery systems and as chemical sensors.     

ATRP synthesis and association properties of temperature responsive dextran copolymers grafted with poly(N-isopropylacrylamide)

Temperature responsive copolymers of dextran grafted with poly(N-isopropylacrylamide) (Dex-g-PNIPAAM) were prepared by atom transfer radical polymerization (ATRP) in homogeneous mild conditions without using protecting group chemistry. Dextran macroinitiator was synthesized by reaction of dextran with 2-chloropropionyl chloride at room temperature in DMF containing 2% LiCl. ATRP was carried out in DMF:water 50:50 (v/v) mixtures at room temperature with CuBr/Tris(2-dimethylaminoethyl)amine (Me₆TREN) as catalyst. Several grafted copolymers with well defined number and length of low polydispersity grafted chains were prepared. Temperature induced association properties in aqueous solution were studied as a function of temperature and polymer concentration by dynamic light scattering, fluorescence spectroscopy and atomic force microscopy (AFM). LCST, ranging from 35 to 41 °C, was significantly affected by number and length of grafted chains. The fine tuning of LCST around body temperature is an important characteristic not obtainable by conventional radical grafting of PNIPAAM. Well defined spherical nanoparticles were formed above the LCST of PNIPAAM. Hydrodynamic diameter was in the range 73-98 nm.     

Preparation and characterization of sodium carboxymethylcellulose/poly(N-isopropylacrylamide)/clay semi-IPN nanocomposite hydrogels

A new kind of pH-/temperature-responsive semi-interpenetrating polymer network hydrogels based on linear sodium carboxymethylcellulose (CMC) and poly(N-isopropylacrylamide) (PNIPA) cross-linked by inorganic clay (CMC/PNIPA/Clay hydrogel) was prepared. The temperature- and pH-responsive behaviors, the mechanical properties of these hydrogels were investigated. The CMC/PNIPA/Clay hydrogels exhibited a volume phase transition temperature around 32 °C with no significant deviation from the conventional PNIPA hydrogels. The swelling ratio of the CMC/PNIPA/Clay hydrogels gradually decreased with increasing the contents of clay. The influence of pH value on swelling behaviors showed that there is a maximum swelling ratio at pH 5.9. Moreover, the CMC/PNIPA/Clay hydrogels exhibited excellent mechanical properties with high tensile stress and elongation at break in excess of 1200%.     

FTIR study on molecular structure of poly(N-isopropylacrylamide) in mixed solvent of methanol and water

The intrachain and interchain hydrogen bonding of poly(N-isopropylacrylamide) (PNIPA) and intermolecular hydrogen bonding between PNIPA chains and the solvent molecules in the mixed solvent of methanol and water have been quantitatively investigated by using Fourier transform infrared (FTIR) spectroscopy at 25 °C. In this spectroscopic system with curve fitting program, we found that in the C-H stretching region, both the N-isopropyl group and the backbone underwent conformational change upon the solvent composition. An analysis of the amide I band suggested that the amide groups of PNIPA were mainly involved in intermolecular hydrogen bonding with water molecules, and the polymer chains were flexible and disordered in the mixed solvent when the methanol volume fraction (χ_v) was lower than 15%. While χ_v was in the range of 15-65%, about 30% of these intermolecular hydrogen bonding between the polymer and water were replaced by intrachain and interchain hydrogen bonding, consequently, PNIPA shrinked as aggregates. If χ_v was above 65%, the interchain hydrogen bonding became predominant due to the solubility characteristics of amphiphilic methanol, and the PNIPA system was homogeneous solution again. We believe that the reentrant transition is related to the weaker interaction between PNIPA molecules and methanol-water complexes, (H₂O)_m(CH₃OH)_n (m/n = 5/1, 5/2, 5/3, 5/4, 5/5) as compared to that between PNIPA and free water or free methanol.