甲壳胺─聚氨酯复合膜的界面粘合研究

测定了甲壳胺─聚氨酯复合膜的静态和动态力学性能，并根据两单组分膜和复合膜的应力－应变行为判断复合膜界面粘合的牢固性。讨论了聚氨酯多孔膜与甲壳胺膜，以及聚氨酯预聚体与甲壳胺膜的粘合机理，并从动态力学性能的测试结果得以证实。     

Effects of precipitation conditions on the membrane morphology and permeation characteristics

The permeability and permselectivity of asymmetric and particulate membranes towards glucose and proteins of various molecular sizes were studied. It was found that the skin layer of asymmetric membranes was permeable to glucose and insulin but effectively prevent the permeation of immunoglobulins. This result parallels our interest for the development of artificial pancreas. It was also found that skinless particulate membranes exhibited not only high permeation rates with respect to albumin and immunoglobulins but also good selectivity between these components. Thus, particulate membranes has the potential to be used in separating albumin from immunoglobulins for treating disorders related to immunoglobulin abnormalities.     

Fluoride-selective sensors based on polyurethane membranes doped with Zr(IV)-porphyrins

The feasibility of using Tecoflex polyurethane as a polymeric matrix for fluoride-selective membranes doped with Zr(IV)-octaethyl-(OEP) or Zr(IV)-tetraphenylporphyrins (TPP) is examined. Membranes containing cationic or anionic additives were prepared, with ionophore working according to neutral or charged carrier mechanism, respectively. Results are compared to those found previously using conventional poly(vinyl chloride) (PVC) as the membrane matrix. It was found that this polymer does not affect significantly the properties of these porphyrins, compared to poly(vinyl chloride) matrix. A dimer-monomer equilibrium determined recently to occur for Zr(IV)-porphyrins in PVC/o-NPOE membranes containing lipophilic anionic additives is also observed to occur (via UV-vis spectrophotometry) in the PU matrix. However, the equilibrium constants for dimer-monomer reactions appear to be lower in PU membranes compared to PVC films, as determined from the degree of super-Nernstian responses towards fluoride as well as the anion concentration ranges required to break the dimer as determined spectroscopically. Due to reduced dimerization of Zr(IV)[OEP]Cl₂ it was possible to obtain electrodes with PU/o-NPOE/KTFPB membranes exhibiting only slightly super-Nernstian (−64.6 mV/dec) response towards fluoride and response time (t₉₅ < 120 s) faster than observed for PVC-based membranes. Good working parameters were also obtained for this metalloporphyrin in PU membrane that forces neutral carrier mechanism (PU/DOS/TDMACl): F⁻ calibration slope −58.3 mV/dec and response time t₉₅ < 12 s. Tested membranes were subsequently applied for construction of miniaturized silicon-based sensors. Better fluoride selectivity was observed for sensors with Zr(IV)[OEP]Cl₂/PU/o-NPOE/KTFPB membranes (: ClO₄⁻ 0.7; Br⁻ −1.9; NO₃⁻ −1.9; Cl⁻ −3.1), compared to Zr(IV)[OEP]Cl₂/PU/DOS/TDMACl matrix (: ClO₄⁻ −0.8; Br⁻ −1.3; NO₃⁻ −1.5; Cl⁻ −2.1). However, latter composition was chosen to be better for flow measurement mode, as dimer formation can be totally prevented within this membrane. Sensors with Zr(IV)[OEP]Cl₂/PU/DOS/TDMACl maintained their characteristics at least for 2 months.     

Effects of moisture on the glass transition temperature of polyurethane shape memory polymer filled with nano-carbon powder

One simple approach to produce electrically conductive polymers is to fill them with conductive powders. This paper investigates the effects of moisture on the glass transition temperature of a polyurethane shape memory polymer (SMP) filled with nano-carbon powders. It is found that the SMP composites before immersion in water have a slightly lower glass transition temperature, and in the mean time, the moisture fraction at the saturation point upon immersion is also lower. On the other hand, the moisture can remarkably reduce the glass transition temperature of the composites. Heating to over 180 °C is an effective way to remove the moisture, which also results in the glass transition temperature back to the original. As the glass transition temperature can be greatly reduced by moisture, a novel feature, namely, the water actutable recovery of SMP composites is also proposed based on this study.     

Effect of the content of urea groups on the particle size in water-borne polyurethane or polyurethane/polyacrylate dispersions

A series of anionic water-borne polyurethane and polyurethane/polyacrylate dispersions and their paint films was prepared. It was found by using TEM that there were three phases in the polyurethane/polyacrylate film, i.e. the hard segment-rich phase and the soft segment-rich phase of polyurethane, and the polyacrylate phase. By increasing the content of urea groups, the glass transition temperature of the soft segments and the dissociation temperature of the long-distance ordering of the hard segments were raised. This should mean that the motion of macromolecular chains was hindered by increasing the content of urea groups, and the hydrophilic carboxyl groups embedded initially in macromolecular coils could thus not transfer easily to the particle surface, which resulted in a greater average particle size in the dispersion.     

Effect of temperature and membrane preparation parameters on gas permeation properties of polymethacrylates

Permeabilities of N₂, Ar, O₂, CO₂, and H₂ gases in PEMA (Polyethylmethacrylate) membranes have been measured above and below glass transition in the temperature range of 25–70 °C. The permeabilities of the gases were observed increasing with temperature. Arrhenius plot of permeability versus temperature data showed that there is a slope discontinuity at near to T_g of PEMA. In addition, the effects of membrane preparation parameters by solvent casting method (percentage of polymer in solvent, annealing temperature, annealing time, evaporation temperature, and evaporation time) have been investigated by using homogenous dense membranes of PEMA. It is observed that membrane preparation parameters strongly affect the membrane performance and the reproducibility of the permeability measurements. On the other hand, the effect of polymer structure on membrane performance has been investigated. Comparison of the permeabilities of N₂, Ar, O₂, CO₂, and H₂ gases in PEMA and PMMA membranes shows that PMMA membranes have smaller permeabilities and higher selectivities than PEMA membranes because of their higher glass transition temperature, T_g. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3025–3033, 2007     

Effects of biopitch on the properties of flexible polyurethane foams

Biopitches are industrial residues obtained by the distillation of the tar recovered during Eucalyptus charcoal production and can be used as a renewable polyol source. Flexible polyurethane foams were prepared with different proportions of biopitch and HTPB (hydroxyl-terminated polybutadiene) and using polymeric MDI (4,4′ diphenyl methane diisocyanate), N,N dimethylcyclohexylamine as a catalyst and water as a blowing agent. Elemental analysis, thermal analysis (TG/DSC), Fourier Transform Infrared Spectroscopy (FTIR), scanning electronic microscopy (SEM), and density results were used aiming to discuss the contribution of biopitch to foams properties. The higher the biopitch content, the higher the thermal stability and the lower the density of the flexible foams (air atmosphere), behaviors similar to those of lignin-based polyurethanes. Biopitch enhanced the oxygen content of the polyurethane foams synthesized, and their reaction with HTPB resulted in stable foams.     

Influence of dipalmitoylphosphatidylcholine on the dissolution of Brazilian chrysotile

It is known that Brazilian chrysotile is rapidly removed from the lungs, but quantitative studies about the influence of lung surfactants on chrysotile dissolution have not been investigated. In this work, the chemical behavior of chrysotile and its dissolution in the presence of dipalmitoylphosphatidylcholine (DPPC) were investigated in physiological conditions. The dissolution was investigated through quantification of magnesium and silicon released by chrysotile. At 37 degrees C, the magnesium concentration is similar to control (without DPPC), which is about 2.0x10(-4)molL(-1), meaning that the dissolution process is not affected by the presence of this surfactant. The same was observed for silicon. The silicon concentration released by chrysotile is similar in all media tested. It is known that the dissolution mechanisms of brucite and tridymite layers are different. From our results, we propose that under physiological conditions, the mechanism of brucite dissolution is based on its interaction with hydrogen ions and that the mechanism of tridymite dissolution is based on a hydrolysis process.     

New breathable and waterproof coatings for textiles: effect of an aliphatic polyurethane on the formation of PEEK-WC porous membranes

PEEK-WC is an amorphous polyetheretherketone with high chemical stability, excellent thermal resistance and significant solubility in various solvents. It has been used to prepare flat membranes by the phase inversion technique. The water vapour permeability through a porous PEEK-WC film was 1350 g/m² day at 26 °C and its liquid entry pressure (LEP) of water equivalent to a column of 2.0 m. These values were remarkably improved by addition of an aliphatic ether polyurethane (PU) into the PEEK-WC/DMF dopes: the water vapour flux was increased up to 2000 g/m² day and the LEP was equivalent to 12.5 m. This improvement is correlated to the different structure of the membranes: a spongy, porous and almost symmetric structure for the PEEK-WC/PU membranes, and an asymmetric structure with fingers for PEEK-WC membrane. The presence of PU influences also the mechanical properties of the blend membranes. The role of the PU on the resulting membrane morphology is rationalised on the basis of the mechanism of phase separation.     

Development of pH sensor based on aromatic polyurethane matrix

The synthesized aromatic polyurethane (APU)-based all-solid-state (ASS) pH sensor was developed with the same APU-based reference site in an ASS multi sensing electrode. The best analytical performance (the linear range of pH 3.0–11.5, slopes of 57 mV pH⁻¹) was obtained with the membrane composition of 33:66:1 (wt.%) of APU/plasticizer (NPOE)/ionophore (N,N-dioctadecylmethylamine) with the addition of lipophilic additive (KTpClPB, 5 mol.%). This ASSE exhibits more advantages of increasing stability, reducing membrane resistance and reducing anion interference.     

Determination of the solubility, dissolution enthalpy and entropy of Deflazacort in different solvents

The solubility of Deflazacort in four solvents, acetone, ethyl acetate, ethanol and 2-propanol, was measured at temperatures ranging from 293.15 K to 348.15 K at atmospheric pressure using Laser Monitoring Technique. The solubility data were correlated by the modified Apelblat model. Then the dissolution enthalpy and entropy of Deflazacort were predicted from the solubility data using van’t Hoff equation. In this study, it should be concluded that the viscosity and surface tension of solvents affect the solubility behavior, dissolution enthalpy and entropy of Deflazacort in different solvents.     

Side chain crosslinking of aromatic polyethers for high temperature polymer electrolyte membrane fuel cell applications

Novel aromatic polymers bearing polar pyridine units in the main chain and side chain crosslinkable hydroxyl and propargyl groups have been successfully synthesized. The polymers have been investigated in terms of their critical properties related to their application in high temperature polymer electrolyte membrane fuel cells, such as doping ability, mechanical properties, and thermal stability. Crosslinked membranes were prepared by direct crosslinking of hydroxyl side chain groups with decafluorobiphenyl used for the first time as a crosslinking agent. However, further functionalization of hydroxyl groups to the propargyl derivative has also led to crosslinked polymers after thermal curing. Both types of crosslinked membranes exhibited higher glass transition temperatures as well as lower doping levels when doped in phosphoric acid compared with the non crosslinked analogs, confirming the formation of a successfully crosslinked network. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Study on thermal properties of polyurethane nanocomposites based on organo-sepiolite

The effects of sepiolite modified with γ-aminopropyltriethoxylsilane (KH550-Sp) on thermal properties of polyurethane (PU) nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TG), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), and tensile test. The DSC results showed that the glass transition temperature of hard segments in PU/KH550-Sp nanocomposite increased with the increase of KH550-Sp, because sepiolite restricted the formation of hydrogen bonding within hard segments of polyurethane. TG results revealed that the thermal stability of PU was improved by KH550-Sp, and the onset decomposition temperature for PU nanocomposites with a KH550-Sp content of 3 wt% was about 20 °C higher than that for pure PU. The tensile properties of pure PU and nanocomposites before and after ageing 120 °C for 72 h were determined, and it was observed that the percentage loss in tensile strength decreased with the addition of KH550-Sp because of an oxidation barrier of KH550-Sp confirmed by ATR-FTIR.     

Monitoring of oil-based polyurethane synthesis by FTIR-ATR

Oil-based polyurethanes were synthesized from triglyceride oil-based hydroxyl containing material and toluene diisocyanate or hexamethylene diisocyanate for wound dressing applications. The reactions were carried out with or without catalyst at 90 °C. The amount of free isocyanate during the reaction was determined by a FTIR-ATR method, and the results were compared with those from a back-titration method. The data obtained were used for determination of kinetic parameters.     

Biodegradable shape memory polyurethanes with controllable trigger temperature

A series of random copolymers(PCLAs) were synthesized by ring-opening polymerization of D,L-lactide(LA)and ε-caprolactone(CL) with different molar ratios. PCLA based polyurethanes(PCLAUs) were obtained by chain-extending of PCLA and polytetramethylene ether(PTMEG) with hexamethylene diisocyanate(HDI). All the PCLAUs exhibit good shape memory properties with high shape fixity ratios above 98% and shape recovery ratios above 82% in the first cycle and 91% in the second cycle. PCLAUs with less CL content show faster recovery speed and PCLAUs with more CL content show higher shape recovery ratio. The trigger temperature can be tuned or controlled around body temperature by adjusting the molar ratio of LA to CL. The PCLAUs have potential applications in implant biomedical devices, especially for minimally invasive deployable devices.     

Micropore formation mechanism in iridium coating after high‐temperature treatment

Noble metal iridium is of great interest for high‐temperature applications and extreme environments. A high (110)‐oriented iridium coating was prepared by a double glow plasma process on the surface of niobium substrate. The morphology and composition of the coating were determined by scanning electron microscopy, energy‐dispersive X‐ray spectroscopy and X‐ray photoelectron spectroscopy, respectively. The phase of the coating was identified by X‐ray diffraction analysis. The misorientation angle distributions of grains on the surface and cross section of the coating were characterized by electron backscatter diffraction system. The uniform and pure iridium coating consisted of the submicrometer‐sized columnar grains with high‐angle boundary. The mean misorientation angles on the surface and cross section of the coating were 38.6° and 45.6°, respectively. After high‐temperature treatment, the coating was composed of equiaxed grains with distinct grain boundaries. Micropores appeared on the fracture surface of the coating. The micropore formation mechanism in Ir coating after high‐temperature treatment was investigated. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of chemical structure on combustion and thermal behaviour of polyurethane elastomer layered silicate nanocomposites

The effect of polyol molecular weight and functionality on nanodispersion of clay in PU/clay nanocomposites and the investigation of their thermal and combustion properties are reported and discussed. Lamellar elastomer polyurethane nanocomposites were synthesized using polyols with different molecular weight and functionality and according to these parameters they show several degrees of dispersion which affect their thermal and combustion behaviour. A barrier effect of clay layer is shown in TGA experiments by a delay of thermal degradation products release in nanocomposite materials compared to the virgin polymer; this barrier effect also leads to formation of char during combustion which lowers the peak of rate of heat release in cone calorimeter tests and eliminates fire-induced dripping of the nanocomposite sample during UL 94 test. However, in order to achieve non-burning behaviour nanocomposite technology must be combined with conventional flame retardant technology.     

Effects of aromatic diacetylenes on polyurethane degradation by gamma irradiation

The effects of four aromatic diacetylenes on the gamma-irradiation-induced degradation of a commercial polyurethane were studied. Addition of 1 wt% of diphenylbutadiyne, which is homogeneously distributed in the polymer, effectively suppressed the polymer chain degradation. The dose required to decrease tensile strength by 50% was found to be 582 kGy for the polyurethane with 1 wt% of diphenylbutadiyne, while a dose of only 310 kGy for the polyurethane itself. The Young's modulus of the polyurethane alone decreased with dose; meanwhile the films with diphenylbutadiyne did not change. The films with p,p′-dinitrodiphenylbutadiyne behaved differently from others due to their inhomogeneous composition. The amide substituted diacetylenes also showed protecting effect, but in less extent due to the steric effect.     

Effects of phase equilibrium and the rate of mutual dissolution of reactants on the formation of polyurethane block copolymers

Interdiffusion and phase equilibrium in the region of amorphous separation were investigated by means of the microinterference technique at 20–130°C for a number of binary systems based on oligoesterdiol, butanediols, and diisocyanates—components of polyurethane block copolymers. The concentration dependences of interdiffusion coefficients in the mutual dissolution region were determined for all test systems. For systems composed of partially compatible components, the concentration limits of thermodynamically unstable solutions were established. By means of transmission electron microscopy, the structure of polymers synthesized both in the region of single-phase solutions of the reactants and in the phase separation region is assessed.     

Nanophase separation in segmented polyurethane elastomers: Effect of specific interactions on structure and properties

Polyurethanes were prepared from 4,4′-methylenebis (phenyl isocyanate) (MDI), 1,4-butanediol (BD) and poly (tetrahydrofurane) polyether polyol (PTHF). The -OH functional group ratio of polyol/total diol was kept constant at 0.4 in all experiments, while the ratio of the isocianate and hydroxyl groups (NCO/OH) changed between 0.940 and 1.150. Melt polymerization was carried out in an internal mixer. The polymers were characterized with a number of methods including GPC, FTIR, WAXS, DSC, DMA and tensile testing. Changing stoichiometry modifies molecular weight as expected, but the relative concentration of end-groups also changes at the same time. The respective end-groups preferentially associate with each other leading to phase separation. -OH end-groups enter into weaker interactions with each other than urethane and amine groups. The extent of phase separation, as well as the size and properties of the dispersed phase depend on composition. Each property of the polymer is affected differently by molecular weight and phase separation. Melt viscosity depends mostly on the length of the molecules, ultimate tensile properties are influenced also by interactions, while stiffness is determined almost exclusively by phase structure.