Study on biodegradable polymer. 3. Synthesis and characterization of poly(DL-lactic acid)-co-poly(ethylene glycol)-co-poly(L-lysine) copolymer

The synthesis of poly(DL-lactic acid)-co-poly(ethylene glycol)-co-poly(L-lysine) copolymer was investigated by the reaction of amino acid-N-carboxy anhydride with lactic acid anhydrosulphite and methoxypolyoxyethylene amine (MPEG-NH₂). The successful synthesis was obtained after adding dibutylmegnesium into the system. The product was proved to be copolymer. The solubility of the polymer revealed that it was ionic polymer.     

Hydrolysis of poly(l-lactic acid) using microwave irradiation

Poly(l-lactic acid) (PLLA) was hydrolyzed using microwave irradiation, and yields of the resultant lactic acid and reaction time were compared with those obtained by conventional heating. In both cases, the reaction temperature was maintained at 170 °C and the weight ratio of PLLA:H₂O was 3:1. Under conventional heating, the lactic acid yield reached saturation after 800 min at 45%, whereas only 120 min was required to reach the same yield level under microwave irradiation. The optical purity under conventional heating decreased with hydrolysis of the PLLA and dropped to 94%ee when the lactic acid yield reached at 45%. Under microwave irradiation, however, the optical purity decreased only after the equilibrium state of hydrolysis was attained. Therefore, to maintain the optical purity at 98%ee, it was necessary to stop microwave irradiation when the lactic acid yield reached 45%.     

Synthesis of l-aminohomohistidine (l-Ahh)

A short synthesis of l-aminohomohistidine (l-Ahh), which starts from readily available δ-hydroxy-l-lysine is described. The embedding of the basic guanidino moiety in the aromatic imidazole lowers the basicity of the side chain to a pK_a of 8.3. It is proposed that l-Ahh may be employed as an arginine-mimetic in medicinal chemistry.     

Investigation of the degradation behaviour of poly(ethylene glycol-co-d,l-lactide) copolymer

The aim was to investigate the degradation behaviour of poly(ethylene glycol-co-d,l-lactide) (PEG-d,l-PLA) multiblock copolymer, in bulk and as microspheres, in aqueous medium. The degradation behaviour of PLA homopolymers in bulk and microspheres was evaluated as comparison.Microsphere preparation was performed by the double emulsion solvent evaporation method. Physical-chemical characterization of the raw polymers and the microspheres was performed by nuclear magnetic resonance (NMR) and modulated differential scanning calorimetry (MDSC). Polymer molecular weight, before and after incubation in aqueous environment, was evaluated by GPC; water uptake and mass loss were determined gravimetrically.The presence of PEG segments inside PLA chains gave a characteristic spongy structure to the microspheres. A significant increase in polymer T_g values was found for the microsphere formulations compared to polymer in bulk. After 63 days of incubation in the aqueous environment, the PEG-d,l-PLA microspheres achieved an average M_w reduction of 47% compared to 20% for PLA microspheres. The corresponding M_w decrease of the polymers in bulk was significantly higher: 72% and 41% for PEG-d,l-PLA and PLA, respectively.The data show how the degradation behaviour of polymer in bulk in an aqueous environment is significantly different from the behaviour of the corresponding microspheres. These results highlight the importance of performing a thorough physical-chemical characterization on microsphere formulations.     

Synthesis of novel star-like hyperbranched polymers with poly(amido amine) core and poly(l-lysine) shell

Hyperbranched poly(amido amine)s containing vinyl and hydroxyl groups were successfully synthesized via Michael addition polymerization of triacrylamide (TT) and 3-amino-1,2-propanediol (APD) with equal molar ratio in feed. ¹H, ¹³C and HSQC NMR techniques were used to clarify the structure of hyperbranched polymers and polymerization mechanism. The Michael addition reaction of hyperbranched poly(1TT-1APD)s with primary amine-terminated poly(ε-benzyloxycarbonyl-l-lysine)s [PLys(Z)] yielded a star-like hyperbranched polymers with poly(1TT-1APD) core and Plys(Z) shell. The Z groups in PLys(Z) were removed under acidolysis, and thus star-like hyperbranched polymers with hydroxyl groups inside and primary amine groups outside were obtained successfully.     

Synthesis and characterization of hydrolysable poly(ether-urethane-urea)s derived from l-leucine anhydride cyclopeptide; a green synthetic method for monomer

l-leucine anhydride cyclodipeptide (LAC) was prepared through a green method under microwave irradiation with good yield. Then a new class of hydrolysable poly(ether-urethane-urea)s (PEUUs) was synthesized via two-step polymerization method. In the first step, 4,4′-methylene-bis-(4-phenylisocyanate) (MDI) was reacted with LAC to produce isocyanate-terminated poly(imide-urea) oligomers (hard segment). Reaction of the resulting pre-polymer with different molecular weights (MW) of polyethyleneglycols (PEG)s such as PEG-400, PEG-600, PEG-1000 and PEG-2000 was the second step to furnish a series of new PEUUs. The resulting multiblock copolymers have inherent viscosities in the range of 0.4-1.8 dL/g. These multiblock copolymers are hydrolysable, thermally stable and soluble in amide-type solvents. Polymers containing different molecular weights of PEGs soft segments show different thermal stability, phase separation, hard segment cohesiveness and hydrolysis rate. Some structural characterization and physical properties of these PEUUs are reported.     

Preparation and characterization of biodegradable poly(l-lactide)/chitosan blends

In order to improve the properties of chitosan and obtain new fully biodegradable materials, blends of poly(l-lactide) (PLLA) and chitosan with different compositions were prepared by precipitating out PLLA/chitosan from acetic acid-DMSO mixtures with acetone. The blends were characterized by Fourier transform infrared analysis (FTIR), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), ¹³C solid-state NMR and Wide-angle X-ray diffraction (WAXD). FTIR and XPS results showed that intermolecular hydrogen bonds existed between two components in the blends, and the hydrogen bonds were mainly between carbonyls of PLLA and amino groups of chitosan. The melting temperatures, cold crystallization temperatures and crystallinity of the PLLA component decreased with the increase in chitosan content. Blending chitosan with PLLA suppressed the crystallization of the PLLA component. Although the crystal structure of PLLA component was not changed, the crystallization of the blends was affected because of the existence of hydrogen bonds between two components, which was proved by WAXD results.     

The synthesis of 6-trifluoroethyl-l-lysine: a method to introduce functionality at C-6 of l-lysine

Described is a method of introducing trifluoroalkyl groups at C-6 of lysine. This chemistry has the potential to introduce a variety of functionality at C-6 of lysine.     

Phase behavior of biodegradable amphiphilic poly(l,l-lactide)-b-poly(ethylene glycol)-b-poly(l,l-lactide)

This study describes the miscibility phase behavior in two series of biodegradable triblock copolymers, poly(l-lactide)-block-poly(ethylene glycol)-block-poly(l-lactide) (PLLA-PEG-PLLA), prepared from two di-hydroxy-terminated PEG prepolymers (M_n = 4000 or 600 g mol⁻¹) with different lengths of poly(l-lactide) segments (polymerization degree, DP = 1.2-145.6). The prepared block copolymers presented wide range of molecular weights (800-25,000 g mol⁻¹) and compositions (16-80 wt.% of PEG). The copolymer multiphases coexistance and interaction were evaluated by DSC and TGA. The copolymers presented a dual stage thermal degradation and decreased thermal stability compared to PEG homopolymers. In addition, DSC analyses allowed the observation of multiphase separation; the melting temperature, T_m, of PLLA and PEG phases depended on the relative segment lengths and the only observed glass transition temperature (T_g) in copolymers indicated miscibility in the amorphous phase.     

Novel stereocontrolled approach to conformationally constrained analogues of l-glutamic acid and l-proline via stereoselective cyclopropanation of 3,4-didehydro-l-pyroglutamic ABO ester

A new stereocontrolled approach to l-(carboxycyclopropyl)glycines (l-CCGs) and 3,4-methano-l-prolines, conformationally constrained analogues of l-glutamic acid and l-proline, respectively, was developed using a 3,4-didehydro-l-pyroglutamate derivative as a common chiral template. The unsaturated l-pyroglutamate derivative employed in this work is a novel chiral synthon in which the carboxyl functionality is protected as a 2,7,8-trioxabicyclo[3.2.1]octyl group (ABO ester). Stereospecific cyclopropanation of the olefin using diazomethane followed by appropriate functional group interconversion gave l-CCG-III and trans-3,4-methano-l-proline with complete stereocontrol. Synthesis of other diastereomers of l-CCG and cis-3,4-methano-l-proline was accomplished by alteration of the 3,4-methanoglutamic acid framework via carboxycyclopropanation of the olefin with sulfur ylide and subsequent Barton decarboxylation reaction of the original γ-carboxyl group included in the pyroglutamate skeleton.     

Crystallization behavior of poly(l-lactic acid)

This article contains a detailed analysis of the crystallization behavior of poly(l-lactic acid) (PLLA). Crystallization rates of PLLA have been measured in a wide temperature range, using both isothermal and non-isothermal methods. The combined usage of multiple thermal treatments allowed to obtain information on crystallization kinetics of PLLA at temperatures almost ranging from glass transition to melting point. Crystallization rate of PLLA is very high at temperatures between 100 and 118 °C, showing a clear deviation from the usual bell-shaped curve. This discontinuity has been ascribed to a sudden acceleration in spherulite growth, and is not associated to morphological changes in the appearance of PLLA spherulites. Experimental data of spherulite growth rates of PLLA have been analyzed with Hoffman-Lauritzen method. Applicability and limitations of this theoretical treatment have been discussed.     

Effects of mechanical load on the degradation of poly(d,l-lactic acid) foam

Degradable behaviors of polymer for implantation in body should be evaluated before clinical application. The effect of continuous mechanical load on the degradation progress of poly(d,l-lactic acid) (PDLLA) foam gasket was investigated in detail by specially designed load-providing devices. While PDLLA degraded in the PBS solution (pH, 7.4) at 37 °C for 3 months, the changes of surface morphology, molecular weight, elastic modulus, tensile strength and mass loss were recorded. The results revealed that the degradation rates of PDLLA under continuous loads were obviously quicker than those without load. Moreover, the influence of tensile plus compressive load was larger than that of tensile load. It was indicated that in vivo degradation of PDLLA would not only be influenced by the local solution, but also by the surrounding load. When regulating the degradation rate of bioabsorbable polymer, one should consider the indispensable effect of load where implanted.     

Aqueous solution properties of amphiphilic triblock copolymer poly(p-dioxanone-co-l-lactide)-block-poly(ethylene glycol)

A poly(ethylene glycol) (PEG)-based new amphiphilic block copolymer bearing the poly(p-dioxanone-co-l-lactide) (PPDO/PLLA) hydrophobic moieties was prepared. Depending on the copolymer composition and molecular weights, solubility of the polymeric samples in water was varied. Its diluted aqueous solution properties were studied by viscometry, dye solubilization, ¹H-NMR and dynamic light scattering. 1,6-Diphenyl-1,3,5-hexatriene solubilization and ¹H-NMR spectra carried out in CDCl₃ and D₂O were used to prove the existence of hydrophobic domains as the core of micelle. Average particle size of 60-165 nm with low polydispersity and lower negative zeta (ξ) potential of −3 to −14 mV were observed on the aqueous copolymer dispersion.     

Synthesis of d-gluco-, l-ido-, d-galacto-, and l-altro-configured glycaro-1,5-lactams from tartaric acid

The d-gluco-, l-ido-, d-galacto-, and l-altro-configured glycaro-1,5-lactams 1-4 were prepared from the known tartaric anhydride 5 via the aldehyde 6. These lactams are known (1) or potential (2-4) inhibitors of β-d-glucuronidases and α-l-iduronidases. Olefination of 6 to the (E)- and (Z)-alkenes 7 or 8, followed by reagent or substrate controlled dihydroxylation, lactonization, azidation, reduction, and deprotection led in 10 steps and in overall yields of 11-20% to the title lactams.     

Diastereoselective synthesis of new polyhydroxylated indolizidines from (l)-glutamic acid

A diastereoselective synthesis of two new swainsonine's analogues 1a and 1b with the piperidine ring fused to a phenyl nucleus at C6-C7, namely (1R, 2S, 10R, 10aR)-(+)-1,2,10-trihydroxy-1,2,3,5,10,10a-hexahydrobenzo[f] indolizine (1a) and (1S, 2R, 10R, 10aR)-(+)-1,2,10-trihydroxy-1, 2, 3, 5, 10, 10a-hexahydrobenzo[f] indolizine (1b), is described. Throughout this work, the effectiveness of the tricyclic indolizidine dione 5, readily available in three steps from the cheap l-glutamic acid, as an attractive platform for chemo- and stereodivergent transformations is illustrated. The key steps involved totally diastereoselective ketone reduction of compound 5 and catalytic cis-dihydroxylation of the unsaturated amide 10. The synthetic strategy also allowed for the diastereoselective synthesis of benzoanalogues of the 1,8a-di-epi-lentiginosine 3a ((1R, 2S, 10aR)-(+)-1,2-dihydroxy-1, 2, 3, 5, 10, 10a-hexahydrobenzo[f]indolizine) and 2,8a-di-epi-lentiginosine 3b ((1S, 2R, 10aR)-(+)-1,2-dihydroxy-1,2,3,5,10,10a-hexahydrobenzo[f]indolizine).     

Electrospun poly(l-lactide)-grafted hydroxyapatite/poly(l-lactide) nanocomposite fibers

Composite fibers composed of poly(l-lactide)-grafted hydroxyapatite (PLA-g-HAP) nanoparticles and polylactide (PLA) matrix were prepared by electro-spinning. Environmental scanning electron microscope (ESEM) and transmission electron microscopy (TEM) were employed to investigate the morphology of the composite fibers and the distribution of PLA-g-HAP nanoparticles in the fibers, respectively. At a low content (∼4 wt%) of PLA-g-HAP, the nanoparticles dispersed uniformly in the fibers and the composite fibrous mats exhibited higher strength properties, compared with the pristine PLA fiber mats and the simple hydroxyapatite/PLA blend fiber mats. But when the content of PLA-g-HAP further increased, the nanoparticles began to aggregate, which resulted in the deterioration of the mechanical properties of the composite fiber mats. The degradation behaviors of the composite fiber mats were closely related to the content of PLA-g-HAP. At a low PLA-g-HAP content, degradation may be delayed due to the reduction of autocatalytic degradation of PLA. When PLA-g-HAP content was high, degradation rate increased because of the enhanced wettability of the composite fibers and the escape of the nanoparticles from fiber surfaces during incubation.     

Enantioselective synthesis of d- and l-α-methylcysteine with hydantoinase

A scalable and cost-effective synthesis of d- and l-α-methylcysteine is described. A key step is d-selective cyclization of N-carbamoyl S-tert-butyl-d,l-α-methylcysteine catalyzed by hydantoinase. d-5-tert-Butylthiomethyl-5-methylhydantoin and N-carbamoyl S-tert-butyl-l-α-methylcysteine were obtained with excellent yield and optical purity, and these compounds were easily separated by filtration. After hydrolysis and cleavage of the tert-butyl group, d- and l-α-methylcysteine hydrochloride were obtained.     

Dications of l-histidine and l-ornithine in layers of copper(II) and cobalt(II) dipicolinato anions

Cobalt(II) and copper(II) dipicolinato complexes having l-histidine and l-ornithine dications are synthesized in water and are characterized by various spectroscopic techniques. X-ray studies reveal that the l-histidine dications are strongly hydrogen bonded and intercalated in the layered structures of dipicolinato complex anions with repeated unit in 1:1 ratio. Whereas l-ornithine dications form hydrogen bonded repeated units of cations and anions in 2:2 ratio. The cations are held in the layered structures formed by the association of the amino acid cations and metal dipicolinato anions supported by water through strong hydrogen-bond interactions. The complexes thus formed are optically active and exhibit specific rotation in the range of +4 to +12°.     

Biodegradation of poly(l-lactide-co-glycolide) tube stents in bile

The objective of this study was to evaluate degradation behavior and the feasibility of biodegradable polymeric stents in common bile duct (CBD) repair and reconstruction. Various molar ratios of lactide (LA) and glycolide (GA) in poly(l-lactide-co-glycolide) (PLGA) were synthesized and processed into a circular tubing of ∼10.0 mm outer diameter and a wall thickness of about 2.0 mm. This tubing was cut into 40.0 mm length to form CBD stents. The stents were placed into human bile to determine the degradation behavior in vitro. The morphology, configuration, mass loss, water uptake, molecular weight and composition changes were examined. The PLGA with LA/GA = 71/29 exhibited an acceptable degradation life and was chosen as an in vivo stent material. These PLGA stents were used in common bile duct exploration (CBDE) and primary suturing for rats. Degradation status of the stents was examined and comparison was made between those before and after surgical procedure. The results showed that the polymer stents exhibited the same biomedical functions as T tubes and spontaneously disappeared from CBD in 4-5 weeks. Therefore, the PLGA stents fits the requirements in repair and reconstruction of CBD, to support the duct, guide bile drainage and reduce T-tube-related complications.     

A highly efficient synthesis of unnatural l-sugars from d-ribose

A preparative and short synthesis of l-ribose and l-apiose was accomplished starting from d-ribose via stereoselective cis-dihydroxylation and C2-hydroxymethylation, respectively. These l-sugars can serve as versatile intermediates for the synthesis of l-nucleosides.