Self-accelerated biodegradation of electrospun poly(ethylene glycol)-poly(l-lactide) membranes by loading proteinase K

Proteinase K was successfully loaded inside ultrafine fibers of poly(ethylene glycol)-poly(l-lactide) (PELA) by emulsion electrospinning. A core/shell fiber structure was formed and verified by a transmission electron microscope. In vitro biodegradation of electrospun PELA membranes containing proteinase K (PELA-P) was examined in Tris-HCl buffer solution at pH 8.6 and 37 °C in comparison with electrospun PELA membranes without proteinase K. During biodegradation, mass loss, water absorption, pH value of the incubated buffer, fibrous morphology and thermal properties were monitored. Results suggested that PELA-P membranes degraded significantly faster than PELA membranes. A significant drop in pH value of the buffer after incubation of PELA-P membranes for 1 d was observed, and after 7 d, PELA-P membranes lost their fibrous appearance and masses almost completely. In contrast, electrospun PELA membranes did not show any obvious changes. The obtained electrospun PELA-P membranes exhibited self-accelerated biodegradability and could benefit drug controlled release and tissue regeneration.     

Effects of molecular weight and small amounts of d-lactide units on hydrolytic degradation of poly(l-lactic acid)s

Films of poly(l-lactic acid) (PLLA) with different number-average molecular weights (M_n) and d-lactide unit contents (X_d) were made amorphous and the effects of molecular weight and small amounts of d-lactide units on the hydrolytic degradation behavior in phosphate-buffered solution at 37 °C of PLLA were investigated. The degraded films were investigated using gravimetry, gel permeation chromatography, polarimetry, differential scanning calorimetry, X-ray diffractometry, and tensile testing. To exclude the effects of crystallinity on the hydrolytic degradation, the films were made amorphous by melt-quenching. The incorporation of small amounts of d-lactide units drastically enhanced the hydrolytic degradation of PLLA. In the period of 0-32 weeks, the hydrolytic degradation rate constant (k) of PLLA films increased with increasing X_d, while the k values did not depend on M_n. This means that the effects of X_d on the hydrolytic degradation rate of the films are higher than those of M_n. In contrast, in the period of 32-60 weeks neither X_d nor M_n was a crucial parameter to determine k values, probably because in addition to these parameters the differences in the amount of catalytic oligomers accumulated in films and crystallinity affect the hydrolytic degradation behavior of the films. The initially amorphous PLLA films remained amorphous even after the hydrolytic degradation for 60 weeks.     

Surface properties and enzymatic degradation of end-capped poly(l-lactide)

Surface properties and enzymatic degradation of poly(l-lactide) (PLLA) end-capped with hydrophobic dodecyl and dodecanoyl groups were investigated by means of advancing contact angle (θ_a) measurement, quartz crystal microbalance (QCM) and atomic force microscopy (AFM). The θ_a values of end-capped PLLA films were larger than those of non-end-capped PLLA films, suggesting that the hydrophobic dodecyl and dodecanoyl groups were segregated on the film surface. The weight changes of end-capped PLLA thin films during enzymatic degradation in the presence of proteinase K were monitored by using a QCM technique. The relatively fast weight loss of PLLA film occurred during first few hours of degradation, followed by a decrease in the erosion rate. The erosion rate of PLLA films at the initial stage of degradation was dependent on the chain-end structure of PLLA molecules, and the value decreased with an increase in the amount of hydrophobic functional groups. The surface morphologies of PLLA thin films before and after degradation were characterized by AFM. After the enzymatic degradation, the surface of non-end-capped PLLA films was blemished homogeneously. In contrast, the end-capped PLLA thin films were degraded heterogeneously by the enzyme, and many hollows were formed on the film surface. From these results, it has been concluded that the introduction of hydrophobic functional groups at the chain-ends of PLLA molecules depressed the erosion rate at the initial stage of enzymatic degradation.     

Kinetics of thermo-oxidative and thermal degradation of poly(d,l-lactide) (PDLLA) at processing temperature

Poly(d,l-lactide) (PDLLA) degraded at processing temperature under air and nitrogen. A random chain scission model was established and used to determine the activation energy E_a, and FT-IR, ¹H and ¹³C NMR were used to elucidate the degradation behavior under different atmospheres. Results showed that there were two to three stages. The 1st stage was dominated by the oligomers containing carboxylic acid groups and hydroxyl groups, during which oxygen and nitrogen had little effect on the degradation, thus they share similar E_a. When the oligomers were consumed over or evaporated, the 2nd stage began, and oxygen had a promoting effect on the thermo-oxidation process, resulting in the great decrease in E_a. The third stage of PDLLA was observed when it degraded under nitrogen over 200 °C, which was caused by the appearance of carboxylic acid substance.     

Effect of type of peroxide on cross-linking of poly(l-lactide)

Poly(l-lactide) (PLLA) was cross-linked with various types of peroxides under constant mole ratios of peroxide-derived radicals to PLLA during reactive extrusion. Peroxides were classified into three groups according to their decomposition rates (Group I: fast, Group II: moderate and Group III: slow) and comparisons were performed within each group. Cross-linking behavior was readily understood in terms of free radical efficiency and hydrogen abstraction ability of radicals. In the case of Groups II and III, the weight-average molecular weight (M_w) of cross-linked PLLA increased with overall hydrogen abstraction ability, because slow decomposition caused uniform cross-linking in molten PLLA. In Group I, M_w and gel fraction were higher than other groups despite Group I's lower hydrogen abstraction ability, leading to the conclusion that peroxide decomposition localized in solid PLLA caused partial cross-linking because of rapid decomposition. Furthermore, the efficiency of peroxide-induced cross-linking was investigated using the Charlesby-Pinner equation.     

Miscibility and hydrolytic degradation in alkaline solution of poly(l-lactide) and poly(p-vinyl phenol) blends

Poly(l-lactide) (PLLA) was melt-blended with poly(p-vinyl phenol) (PVPh) using a two-roll mill, and the miscibility between PLLA and PVPh and degradation of the blend films were investigated. It was found that PLLA/PVPh blend has miscibility in the amorphous state because only single T_g was observed in the DSC and DMA measurements. The T_g of the PLLA/PVPh blend could be controlled in the temperature range from 55 °C to 117 °C by changing the PVPh weight fraction. In alkaline solution, degradation rate of PLLA/PVPh blends was faster than that of neat PLLA because PVPh could dissolve in alkaline solution. The surface morphology of degraded PLLA and PLLA/PVPh blend were observed by SEM. The surface morphology of degraded PLLA/PVPh blend was finer than that of PLLA. Young's modulus of PLLA/PVPh blend increased with increasing PVPh content. Yield stress of PLLA/PVPh blends whose PVPh content was less than 30 wt% kept the level of about 55 MPa and that of PLLA/PVPh blend whose PVPh content was 40 wt% is much lower than that of neat PLLA.     

Racemization behavior of l,l-lactide during heating

To control the depolymerization process of poly(l-lactic acid) into l,l-lactide for feedstock recycling, the racemization of l,l-lactide as a post-depolymerization reaction was investigated. In the absence of a catalyst, the conversion to meso-lactide increased with increase in the heating temperature and time at a higher rate than the conversion into oligomers. The resulting high composition of meso-lactide suggests that the direct racemization of l,l-lactide had occurred in addition to the known racemization mechanism that occurs on the oligomer chains. In the presence of MgO, the oligomerization rapidly proceeded to reach an equilibrium state between monomers and oligomers. The equilibrium among l,l-, meso-, and d,d-lactides was found to be a convergent composition ratio l,l-:meso-:d,d-lactides = 1:1.22:0.99 (wt/wt/wt) after 120 min at 300 °C. This composition ratio also indicates that in addition to the known racemization reaction on the oligomer chains, direct racemization among the lactides is also a frequent occurrence.     

Prevailing mechanisms of the hydrolytic degradation of oligo(d,l-lactide)-grafted dextrans

The predominant mechanism of the hydrolytic degradation of oligo(d,l-lactide)-grafted dextrans in phosphate buffer was followed by quantifying both released dextran and lactic acid from the copolymers. The studied amphiphilic copolymers, with well-defined structure, exhibited various oligo(d,l-lactide) weight fractions (F^OLA) while having a quite high extent of free hydroxyl groups (>90%). Depending on their F^OLA, oligo(d,l-lactide)-grafted dextrans were soluble either in water or in organic solvents (THF, toluene, …) and different prevailing mechanisms of hydrolytic degradation were observed. The copolymer soluble in THF, with longer oligo(d,l-lactide) grafts and higher F^OLA, was found to degrade via a particular mechanism by which the greatest part of dextran was released into buffer medium during the first two weeks of degradation. During the initial stage of degradation, the hydrophilicity of dextran backbone was considered to be the main driving force for the hydrolytic cleavage of the ester linkage between backbone and grafts. Released oligo(d,l-lactide) grafts were found to be degraded via chain-end degradation or random degradation depending on their solubility in buffer medium. In case of water-soluble copolymers with shorter oligo(d,l-lactide) grafts and lower F^OLA, the chain-end degradation was exclusively observed.     

Preparation and characterization of biodegradable poly(l-lactide)/chitosan blends

In order to improve the properties of chitosan and obtain new fully biodegradable materials, blends of poly(l-lactide) (PLLA) and chitosan with different compositions were prepared by precipitating out PLLA/chitosan from acetic acid-DMSO mixtures with acetone. The blends were characterized by Fourier transform infrared analysis (FTIR), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), ¹³C solid-state NMR and Wide-angle X-ray diffraction (WAXD). FTIR and XPS results showed that intermolecular hydrogen bonds existed between two components in the blends, and the hydrogen bonds were mainly between carbonyls of PLLA and amino groups of chitosan. The melting temperatures, cold crystallization temperatures and crystallinity of the PLLA component decreased with the increase in chitosan content. Blending chitosan with PLLA suppressed the crystallization of the PLLA component. Although the crystal structure of PLLA component was not changed, the crystallization of the blends was affected because of the existence of hydrogen bonds between two components, which was proved by WAXD results.     

Thermal and electrical properties of poly(l-lactide)-graft-multiwalled carbon nanotube composites

The dispersion of the nanometer-sized carbon nanotubes in a polymer matrix leads to a marked improvement in the properties of the polymer. This approach can also be applied to biodegradable synthetic aliphatic polyesters such as poly(l-lactide) (PLLA), which has received a great deal of attention due to environmental concerns. In this study, PLLA was melt compounded with multiwalled carbon nanotubes (MWCNTs). A high degree of dispersion of the MWCNTs in the composites was obtained by grafting PLLA onto the MWCNTs (PLLA-g-MWCNTs). After oxidizing the MWCNTs by treating them with strong acids, they were reacted with l-lactide to produce the PLLA-g-MWCNTs. The morphology of the composite was observed with scanning electron microscopy. The mechanical properties of the PLLA/PLLA-g-MWCNT composite were higher than those of the PLLA/MWCNT composite. The thermal stability of the composites was studied using thermogravimetric analysis and their activation energy during thermal degradation was determined using the Kissinger and Flynn-Wall-Ozawa methods. The activation energy of PLLA/PLLA-g-MWCNT was higher than that of PLLA/MWCNT, which indicates that the composite made with the PLLA-g-MWCNTs was more thermally stable than the composite made with the MWCNTs.     

Influence of cellulose nanowhiskers on the hydrolytic degradation behavior of poly(d,l-lactide)

This paper reports the preparation of bionanocomposites based on poly(d,l-lactide) and cellulose nanowhiskers (PDLLA/CNWs) and studies the influence of the CNWs on the hydrolytic degradation behavior of the polylactide. The hydrolytic degradation process was studied in a phosphate buffer medium through the sample weight loss and also by FTIR, DSC and TGA measurements. The presence of CNWs induced a strong delay in the hydrolytic degradation of the PDLLA, even when the concentration of the nanofillers was only 1%. This effect was related to the physical barrier created by the highly crystalline CNWs that inhibited water absorption and hence retarded the hydrolytic degradation of the bionanocomposites. In addition, the incorporation of cellulose nanocrystals in the PDLLA also made the biopolymer more thermally stable, increasing the initial temperature of mass loss even after the degradation in phosphate medium. The results presented here show the possibility of controlling the biodegradability and prolonging the service life of a polylactide through the incorporation of a small quantity of nanofillers obtained from renewable materials.     

Crystallization behavior of poly(l-lactic acid)

This article contains a detailed analysis of the crystallization behavior of poly(l-lactic acid) (PLLA). Crystallization rates of PLLA have been measured in a wide temperature range, using both isothermal and non-isothermal methods. The combined usage of multiple thermal treatments allowed to obtain information on crystallization kinetics of PLLA at temperatures almost ranging from glass transition to melting point. Crystallization rate of PLLA is very high at temperatures between 100 and 118 °C, showing a clear deviation from the usual bell-shaped curve. This discontinuity has been ascribed to a sudden acceleration in spherulite growth, and is not associated to morphological changes in the appearance of PLLA spherulites. Experimental data of spherulite growth rates of PLLA have been analyzed with Hoffman-Lauritzen method. Applicability and limitations of this theoretical treatment have been discussed.     

Synthesis and properties of pentaarmed poly(l-lactide)s on N-dichlorophosphoryl-P-trichlorophosphazene derivative core

N-Dichlorophosphoryl-P-trichlorophosphazene was synthesized by two steps and N-di[p-(hydroxylmethyl)phenoxy]phosphoryl-P-tri[p-(hydroxylmethyl)phenoxy]phosphazene was prepared by the reaction of N-dichlorophosphoryl-P-trichlorophosphazene with the sodium salt of 4-hydroxybenzaldehyde and subsequent reduction of aldehyde groups to alcohol groups by using sodium borohydride. The hydroxyl-terminated pentaarmed compound as initiator for the synthesis of pentaarmed poly(l-lactide)s in the presence of stannous octoate was studied. Effects of molar ratio of monomer to initiator and monomer to catalyst on polymerization were investigated. The results indicate that the molecular weight of the polylactides linearly increases with the molar ratio of l-lactide to initiator. Thermal analysis demonstrates that pentaarmed poly(l-lactide)s possess lower melting point and crystallinity but higher maximum decomposition temperature than those of linear poly(l-lactide)s.     

Effect of layered double hydroxides on the thermal degradation behavior of biodegradable poly(l-lactide) nanocomposites

This study elucidates the thermal degradation behavior of biodegradable poly(l-lactide) (PLLA)/layered double hydroxide (LDH) nanocomposites was explored using thermogravimetric analysis (TGA) and pyrolysis-gas chromatography/mass spectroscopy (Py-GC/MS) in an inert atmosphere. PLLA/LDH nanocomposites were fabricated using PLLA and organically-modified magnesium/aluminum layered double hydroxide (P-LDH) in tetrahydrofuran solution. According to the TGA results, the thermal stability of PLLA/P-LDH nanocomposites was significantly lower than that of pure PLLA matrix, perhaps because P-LDH provides thermal acceleration of the degradation of the underlying polymer from the heat source. The identification of the thermal degradation products by Py-GC/MS evidently shows that introducing P-LDH into PLLA leads to a remarkable change during the thermal degradation process. The main reaction route of neat PLLA was through inter- and intra-transesterification to generate lactides and oligomer. The primary volatile products obtained from PLLA/P-LDH nanocomposites were lactides regardless of the temperature of degradation. These results suggest that the thermal degradation behavior of PLLA/P-LDH nanocomposites is governed by the preferential formation of lactide by the unzipping depolymerization reaction, which is catalyzed by Mg and Al components in P-LDH.     

Characterization and release of triptolide-loaded poly (d,l-lactic acid) nanoparticles

Triptolide (TP), which has immunosuppressive effect, anti-neoplastic activity, anti-fertility function and severe toxicities on digestive, urogenital, blood circulatory system, was used as a model drug in this study. TP-loaded poly (d,l-lactic acid) (PLA) nanoparticles were prepared by the modified spontaneous emulsification solvent diffusion method (modified-SESD method). Dynamic light scattering system (DLS), transmission electron microscope (TEM), atomic force microscopy (AFM), differential scanning calorimetry (DSC), X-ray powder diffractometry and Fourier transform infra-red spectroscopy (FT-IR) were employed to characterize the nanoparticles fabricated for size and size distribution, surface morphology, the physical state of drug in nanoparticles, and the interaction between the drug and polymer. Encapsulation efficiency (EE) and the in vitro release of TP in nanoparticles were measured by the reverse phase high-performance liquid chromatography (RP-HPLC). The produced nanoparticles exhibited a narrow size distribution with a mean size of approximately 150 nm and polydispersity index of 0.088. The morphology of the nanoparticles exhibited a fine spherical shape with smooth surfaces without aggregation or adhesion. TP-entrapped in nanoparticles was found in the form of amorphous or semicrystalline. It was found that a weak interaction existed between the drug and polymer. In all experiments, more than 65% of EE were obtained. The in vitro release profile of TP from nanoparticles exhibited a typical biphasic release phenomenon, namely initial burst release and consequently sustained release. In this case, the particle size played an important role for the drug release. The modified-SESD method was a potential and advantage method to produce an ideal polymer nanoparticles for drug delivery system (DDS).     

Swelling and hydrolytic degradation of poly(d,l-lactic acid) in aqueous solutions

Low molecular weight poly(lactic acid) was synthesized by direct polycondensation of lactic acid. The oligomers were characterized by viscometry, light scattering, and gel permeation chromatography (GPC). The swelling behaviour of tablets made of the above polymer immersed in buffer solutions at 37 °C was studied. In the same experiments, the hydrolytic stability of d,l-PLA was assessed by measuring the weight loss after drying the tablets. In order to inhibit any degradation due to bacteria, formaldehyde was added in the solution as biostatic factor. The effect of an incorporated drug on the swelling behaviour of d,l-PLA tablets was also considered. It was found that the incorporation of drug in d,l-PLA tablets increases their swelling index, probably due to the creation of additional porosity in the specimens or other interaction between drug and polymeric matrix.     

Asymmetric aldol reactions in poly(ethylene glycol) catalyzed by l-proline

A rapid l-proline catalyzed direct aldol reaction between various aldehydes and acetone was achieved using PEG as the solvent with comparable enantioselectivities and yields to those obtained in other solvents. Recycling the catalyst and solvent (PEG) was possible 10 times without loss of activity.     

Thermal degradation of poly(l-lactide): Accelerating effect of residual DBU-based organic catalysts

1,8-Diazabicyclo[5.4.0]undec-7-ene (DBU) organic catalyst has generated a tremendous impact in the metal-free ring-opening polymerization of (di)lactones. Interestingly, its extraction after use has never been studied so far and a simple deactivation by addition of benzoic acid to generate the corresponding salt has always been supposed to kill its activity. This study reveals and highlights the importance of the work-up to remove or at least drastically limit the presence of the benzoic acid/DBU salt from poly(l-lactide). Three different extraction methods allowed us to conclude that a two-step work-up gathering liquid/liquid extractions and a drop by drop precipitation is highly required to keep the enantiomerically pure lactic acid polymer safe. If not perfectly extracted the benzoic acid/DBU salt has been proved to degrade the materials during a melt process even during a differential scanning calorimetry experiment.     

Improvement of mechanical properties of poly(dl-lactide) films by blending of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)

Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) and poly(dl-lactide) (PDLLA) were blended at different ratios in an attempt to form a biomaterial with suitable properties for nerve regeneration. FT-IR and X-ray analysis showed that the blending of the PDLLA component did not alter the helical structure of PHBHHx, but did lead to a reduction of crystallinity. Differential scanning calorimetry (DSC) analysis indicated that the two polymers were immiscible in the melted state. The mechanical properties of certain composite films were more desirable than those of unblended PDLLA films. Blends consisting of PDLLA and PHBHHx at ratios of 2:1 and 1:2 exhibited a lower elastic modulus and a higher elongation at break compared to unblended PDLLA. ELISA results indicated that the amount of fibronectin adsorbed on composite films was much higher than the amount adsorbed on PDLLA film. The results of this study demonstrate the feasibility of using PDLLA/PHBHHx blended materials for biomedical applications.     

New Sn(IV) and Ti(IV) bis(trimethylsilyl)amides in d,l-lactide polymerization, SEM characterization of polymers

Ring-opening polymerization of d,l-lactide initiated with new chlorotris(bis(trimethylsilyl) amido) tin(IV), tetrakis(bis(trimethylsilyl)amido) tin(IV) and titanium(IV) was investigated. New complexes reveal practically quantitative conversion degrees and produced polymers with higher molecular weight with respect to reference alkoxo-species.The X-ray crystal structure of chlorotris(bis(trimethylsilyl)amido) tin (IV) was investigated. Axial enantiomerism of [SnCl{N(SiMe₃)₂}₃] molecules in solution was studied by high-field dynamic NMR, the value of Gibbs activation energy ΔG^‡ = 59.5 kJ/mol.Field emission SEM investigation of bulk polymer samples and thin films on conductive Al foil revealed a stratified fibrous textures in the bulk polymers, as well as nanoscaled topographical features due to coils and entanglements of individual macromolecules in thin films.