用激光分子束外延在玻璃衬底上生长La0.67Sr0.33MnO3薄膜

采用激光分子束外延技术,在玻璃衬底上制备了La_067Sr_033MnO₃ （LSMO） 薄膜,X射线衍射测量结果表明在玻璃衬底上生长的LSMO薄膜沿c轴择优取向生长.在外磁场3 T和88, 220, 300 K条件下,LSMO薄膜的磁电阻变化率分别达到-378%, -268%和-607%.实验结果表明,在廉价的玻璃衬底上制备大面积和具有应用价值的锰氧化物薄膜是可行的. 关键词： 锰氧化物薄膜 玻璃衬底 外延生长     

厚度与应变效应对La0.67Ca0.33MnO3薄膜电输运与居里温度的影响

在厚度为25—400nm范围内，系统地研究了 (001)SrTiO_3(STO), (001)LaAlO_3(LAO)衬底上La_0.67Ca_0.33Mn_O.3 (LCMO)薄膜的电输运与居里温度T_C随薄膜厚度及衬底的变化. 结果表明，随薄膜变薄，电阻率ρ增加，T_C降低. 对于同一薄膜厚度，LCMO/STO薄膜的ρ大于LCMO/LAO基上的薄膜的ρ. T_C衬底的依赖关系则与ρ相反. 分析表明，LCMO薄膜的低温区电阻温度(ρ-T) 符合关系式ρ=ρ_0+Bω_s/sin h^2(ω_s/2/k_BT)+CT^n， 其中ρ_0为剩余电阻；等号右端第二项反映软光学模声子对电子散射的贡献；第三项包括其余可能散射机 理在电输运过程中所起的作用；B，ωs（软光学模声子的平均频率）与C都为拟合系数. 高温区的电输运则由小极化子跃迁模型ρ=DT×exp（E_a/k_BT）描述（E_a为极化子激 发能）. 根据ρ_0，ωs，E_a以及T_Ｃ变化，初步讨论了薄膜中的厚度与应变效应. 进一步 研究发现ωs，E_a的变化与T_C相关，从而说明极化子效应为影响T_C变化的主要因素. 关键词： 锰氧化物薄膜 电输运 居里温度 极化子     

La0.67Ca0.33MnO3(001)薄膜表面结构的扫描隧道显微术研究

利用Scanning Tunneling Microscope(STM)和Scanning Tunneling Spectroscopy(STS)技术研究了La_0.67Ca_0.33MnO₃(001)表面性质,研究发现表面呈现多相分离现象,在锰氧终端面观察到了绝缘性的( 2 × 2 )R45°重构表面和金属性的(1×1)重构表面,在镧钙氧终端面,观察到了表面呈现条纹状结构.La_0.67Ca_{0.33 关键词： 镧钙锰氧薄膜 终端面 绝缘金属转变}     

La0.33Pr0.34Ca0.33MnO3薄膜的应变效应

采用脉冲激光沉积法分别在(100)LaAlO₃和(100)SrTiO₃基片上生长了La_0.33Pr_0.34Ca_0.33MnO₃薄膜,并通过磁测量和电输运测量对生长在不同基片上的La_0.33Pr_0.34Ca_0.33MnO₃薄膜的物性进行了研究.结果表明,基片和薄膜之间的压应力导致La_{关键词： 钙钛矿锰氧化物 相分离 电荷有序}     

相分离La0.33Pr0.34Ca0.33MnO3薄膜体系中的交换偏置效应

在相分离La_0.33Pr_0.34Ca_0.33MnO₃薄膜体系中发现了大的交换偏置效应．在4 K时,交换偏置场的大小达到了约1 kOe．交换偏置效应可能源自薄膜内禀的电子相分离特性或薄膜的表面效应．交换偏置效应表现出强的温度、冷却磁场以及厚度依赖的关系．     

Ag掺杂的La0.67Pb0.33MnO3薄膜中激光感生热电电压效应

采用脉冲激光沉积法在倾斜LaAlO₃衬底上制备了Ag掺杂的La_0.67Pb_0.33MnO₃(LPMO)系列薄膜，发现该类薄膜中有激光感生热电电压(LITV)效应.随着掺Ag量x(x为Ag的质量与LPMO的质量之比)从0.00增加到0.10，LPMO薄膜中的LITV信号的响应时间先递减后递增，但始终小于未掺Ag的薄膜，掺Ag量x=0.06时响应时间最小.研究发现LPMO薄膜存在一个最佳厚度，在这一厚度下可使得LITV信号 关键词： 3薄膜')" href="#">LaPbMnO₃薄膜 激光感生热电电压 各向异性Seebeck系数 响应时间     

La2/3Ca1/3MnO3薄膜的光致电阻率变化特性

射频磁控溅射法制备了La_2/3Ca_1/3MnO₃纳米薄膜(LCMO).该薄膜发生FM-PM相变的转变点温度为T_c≈308K（近似为电阻峰值温度T_p）；在不同温度下的光电导性质实验表明所制备的LCMO薄膜在连续激光作用时低温段（Tc）表现为光致电阻率增大效应，即ΔR/R＞0，并在R-T曲线拐点附近取得极大值，（ΔR/R）_max=43.5%；当T>T关键词： 钙钛矿薄膜 光响应 电子自旋 小极化子     

La0.67Ba0.33MnO3薄膜的激光辐照效应研究

利用脉冲激光沉积技术在LaAlO₃（00l）单晶衬底上制备了La_067Ba_033MnO₃薄膜,研究了CO₂激光辐照对La_067Ba_033MnO₃薄膜的微结构和磁电性能的影响.结果表明,经激光辐照后,La_067Ba_033MnO₃薄膜的结晶性增强,薄膜应变减小;薄膜表面形貌由“岛状”结构变为“平原"结构,且粗糙度大大降低;同时,薄膜的饱和磁化强度、铁磁居里温度、金属—绝缘态转变温度和磁电阻增大,而矫顽场和电阻率减小.根据对传统退火效应的分析和理论计算,认为激光辐照导致的表面微结构的变化以及薄膜的氧含量和均匀性的提高对La_067Ba_033MnO₃薄膜的磁电性能的改善与优化密切相关. 关键词： 庞磁电阻 激光辐照 脉冲激光溅射沉积     

La0.67Pb0.33MnO3的Preisach分析

测量了居里点TC=360K的钙钛矿La0.67Pb0.33MnO3在2K关键词： Preisach模型 磁滞回线 磁化强度 磁化率     

La0.67Ca0.33MnO3单晶中Fe的掺杂提高本征磁电阻率和激活能的研究

La_0.67Ca_0.33MnO₃ and La_0.67Ca_0.33Mn_0.96Fe0.04O₃单晶的磁性和磁电阻特性。由于缺少晶粒间界，磁场对于自旋涨落的抑制作用更加明显，所以单晶中的磁电阻率比多晶的提高了两个数量级。通过Fe的掺杂，在40×10⁵A/m的磁场下，磁电阻率从3400%进一步提高到了17600%。通过对居里温度以上电阻率的小极化子模型拟和的结果，我们看到随着Fe的掺杂，激活能被提高。磁极化子激活能的增大可以更加局域电子，这可能是在Fe掺杂单晶中本征磁电阻率进一步提高的主要原因。     

Magnetotransport properties of La0.67Ca0.33MnO3//La0.67Sr0.33MnO3 bilayers

The perovskite bilayers La0.67Ca0.33MnO3 （LCMO） （100 nm） / La0.67Sr0.33MnO3（LSMO） （100 nm） and LSMO （100 nm） / LCMO （100 nm） are fabricated by a facing-target sputtering technique. Their transport and magnetic properties are investigated. It is found that the transport properties between them are different obviously due to distinguishable structures, and the different lattice strains in both films result in the difference of metal-to-insulator transition. Only single-step magnetization loop appears in our bilayers from 5K to 320K, and the coercive force of LSMO/LCMO varies irregularly with a minimum ～ 2387A/m which is lower than that of LCMO and LSMO single layer films. The behaviour is explained by some magnetic coupling.     

Dependence of magnetic anisotropy of the La0.67Ca0.33MnO3 films on substrate and film thickness

Strain in the La_0.67Ca_0.33MnO₃ films has been tuned by varying substrate and film thickness, and its effects on magnetic anisotropy are studied based on the measurements of isothermal magnetization. Measuring the strain in the films by the out-of-plane lattice parameter (c), we found a strong dependence of the magnetic anisotropy constant (Ku) on strain. Ku decreases linearly from ∼−1.1×10⁶ erg/cm³ for c=0.763 nm to 1.2×10⁶ erg/cm³ for c=0.776 nm, corresponding to a change from tensile strain to compressive strain. Positive Ku signifies a uniaxial anisotropy with the easy axis perpendicular to the film plane, while negative Ku demonstrates an anisotropy of the easy plane character. Smaller or larger c leads a decrease or increase in Ku, which indicates the presence of other effects in addition to those associated with strain. Three distinctive processes for the magnetization are observed along the hard magnetic axis of the films on (001)SrTiO₃, suggesting a possibility of strain relaxation even in ultra-thin films.     

Pico-second photoelectric characteristic in manganite oxide La0.67Ca0.33MnO3 films

Ultrafast photoelectric characteristic has been observed in La_0.67Ca_0.33MnO₃ films on tilted SrTiO₃ substrates. A pico-second (ps) open-circuit photovoltage of the perovskite manganese oxide films has been obtained when the films were irradiated by a 1.064μm laser pulse of 25 ps duration. The rise time and full width at half-maximum of the photovoltage pulse are ～300 ps and ～700 ps, respectively. The photovoltaic sensitivity was as large as ～500 mV/mJ.     

Enhancing low-field magnetoresistance of La0.67Ca0.33MnO3 films deposited on anodized aluminium-oxide membranes

In this paper we report a new method to fabricate nanostructured films, La0.67Ca0.33MnO3 （LCMO） nanostructured films have been fabricated by using pulsed electron beam deposition （PED） on anodized aluminium oxide （AAO） membranes, The magnetic and electronic transport properties are investigated by using the Quantum Design physics properties measurement system （PPMS） and magnetic properties measurement system （MPMS）. The resistance peak temperature （Tp） is about 85 K and the Curie temperature （To） is about 250 K for the LCMO film on an AAO membrane with a pore diameter of 20nm. Large magnetoresistance ratio （MR） is observed near Tp. The MR is as high as 85% under 1 T magnetic field. The great enhancement of MR at low magnetic fields could be attributed to the lattice distortion and the grain boundary that are induced by the nanopores on the AAO membrane.     

Reversal transient laser-induced voltages in La2/3Ca1/3MnO3 films

This paper reports that the transient laser-induced voltages have been observed in La2/3Ca1/3MnO3 thin films on MgO （001） in the absence of an applied current. A peak voltage of - 0.15 V was detected in response to 0.015J pulse of 308 nm laser. It is demonstrated that the signal polarity is reversed when the films are irradiated through the substrate rather than at the air/film interface. Off-diagonal thermoelectricity may support the inversion of the signal when the irradiation direction is reversed.     

Thickness dependence of electroresistance in La0.67Ca0.33MnO3 epitaxial films

The electroresistance (ER) of La_0.67Ca_0.33MnO₃ (LCMO) epitaxial thin films with different thicknesses was studied. For the 110 nm thick LCMO film, its ER shows a maximum at T_p, where the resistance shows a peak, and decreases to zero at lower temperatures. While for the 30 nm thick LCMO film, its ER is remarkable in a wide temperature range. Another interesting observation in this work is that the electric current can tune the magnetoresistance of the ultrathin LCMO thin film. The results were discussed by considering the coexistence of ferromagnetic metallic phase with the charge ordered phase, and the variation of the phase separation with film thickness and electric current. This work also demonstrates that electric current can tune the magnetoresistance of the manganites, which is helpful for their applications.     

Fabrication and magnetic response probed by RF transverse susceptibility in La0.67Ca0.33MnO3 nanowires

The temperature and magnetic field dependence of the radio-frequency (RF) transverse susceptibility (χ_T) of La_0.67Ca_0.33MnO₃ crystalline nanowires has been studied using a very sensitive self-resonant tunnel-diode oscillator (TDO) technique. The nanowires were synthesized using porous templates of anodized alumina by chemical solution deposition technique, and the crystalline nature of the nanowires with the average diameter of 70 nm was confirmed by TEM, SAED, and HREM. RF transverse susceptibility experiments reveal the presence of a double-peak structure at T≤245 K (the Curie temperature) but a single peak at T>245 K. This distinguishes the low temperature ferromagnetic state from the high temperature paramagnetic state. The effective magnetic anisotropy field (H_K), which corresponds to the peak location of χ_T, has been found to increase with decrease in temperature from the Curie temperature.     

Response of the capacitance of a planar La0.67Ca0.33MnO3/SrTiO3/La0.67Ca0.33MnO3 heterostructure to an electric field

Manganite film electrodes were integrated with a spacer layer of strontium titanate to produce an epitaxial La_0.67Ca_0.33MnO₃/(1000 nm)SrTiO₃/La_0.67Ca_0.33MnO₃ (LCMO/STO/LCMO) heterostructure by laser ablation. At T = 300 K, the mechanical stresses in the STO layer relaxed to a considerable extent, while the LCMO electrodes were found to be under biaxial lateral tensile strain, with the lattice unit cell of the top electrode distorted considerably stronger (a _∥/a _⊥ ≈ 1.026) than that of the bottom electrode (≈1.008) (a _∥ and a _⊥ are the unit cell parameters in the substrate plane and along the normal to its surface, respectively). The reciprocal of the capacitance C of the plane-parallel LCMO/STO/LCMO film capacitors thus formed increased almost linearly with increasing temperature T in the range 50–250 K. At T < 100 K, the capacitance C decreased by approximately 50% in an electric field E = 40 kV/cm. After the electric field E was varied as 0 → + 100 kV/cm → 0, the capacitance C decreased by approximately 3% and the maximum in the C(E, T > 200 K) dependence shifted by approximately 9 kV/cm with respect to the point E = 0.