基于离子液体的单滴微萃取-毛细管电泳在线联用测定水体中3种溴酚类化合物

建立了基于离子液体的单滴微萃取-毛细管电泳联用测定溴酚类化合物的方法。考察了萃取剂种类与体积、萃取时间、有机溶剂、盐浓度及萃取温度对萃取效率的影响。确定了最佳萃取条件为:以1-丁基-3-甲基咪唑六氟磷酸盐([C₄MIM]PF₆])离子液体作为萃取剂,萃取时间为8 min,样品溶液中NaCl浓度为10%(质量分数),萃取温度为20 ℃。在最佳条件下,3种溴酚(4-溴酚、2,6-二溴酚和2,4,6-三溴酚)在1~100 mg/L范围内呈良好的线性关系,线性相关系数为0.9939~0.9988;检出限为0.3 mg/L (S/N=3);该方法对3种溴酚的富集倍数分别为115.8、327.0和569.8; 6次平行测定的相对标准偏差为5.21%~6.47%;对本地区自来水、河水和湖水的加标回收率为87.8%~96.7%。结果表明,该方法稳定可靠,适合于水体中溴酚类污染物的测定。     

Improvement in Solubility of Poorly Water Soluble Drug by Cogrinding with Highly Branched Cyclic Dextrin

We investigated the enhancement of the solubility of glibenclamide (GCM), a poorly water soluble anti-diabetes drug, by cogrinding it with highly branched cyclic dextrin (HBCD) using a ball mill. Highly branched cyclic dextrin (HBCD) is a novel cyclic glucan produced from waxy corn starch by the cyclization reaction of a branching enzyme. When GCM crystals were coground with HBCD for 2 h, the solubility of GCM was improved to 12.4 μg/ml, while the concentration of HBCD was 5.0 mg/ml. Additionally, the GCM solubilized with HBCD was chemically stable in aqueous solution for at least 1 week at room temperature. The peak intensity assigned to crystalline GCM disappeared after cogrinding it by observing its powder X-ray diffraction pattern, which means that the crystalline structure of GCM could be disrupted. In the DSC measurement, the ground mixture showed a single endothermic peak, even though a temperature depression of the endothermic peak due to GCM crystal was observed. After the cogrinding, two sharp peaks assigned to sulfonylurea and benzoyl carbonyl stretching bands varied to broaden the peak to around 1640 cm⁻¹ in the C=O stretching region. These results suggested the formation of solid dispersion between GCM and HBCD.     

Determination of Hexabromocyclododecane in Expanded Polystyrene and Extruded Polystyrene Foam by Gas Chromatography-Mass Spectrometry

A gas chromatography-mass spectrometry (GC/MS) method for the determination of hexabromocyclododecane (HBCD) in expanded polystyrene and extruded polystyrene foam (EPS/XPS) was developed. The EPS/XPS samples were ultrasonically extracted with acetone and the extracts were purified by filtration through a microporous membrane (0.22 μm) and solid-phase extraction. The samples were analyzed using a GC/MS using the selected ion monitoring mode. The ions 157, 319 and 401 were selected as the qualitative ions, while ion 239 was chosen as the quantitative ion. An HBCD standard working solution with a concentration range of 1.0–50.0 mg/L showed good linearity. The detection limit of HBCD was 0.5 mg/kg, meeting the LPC limit (<100 or 1000 mg/kg). Six laboratories were selected to verify the accuracy of the method, and 10 samples were tested. The interlaboratory relative standard deviation range was 3.68–9.80%. This method could play an important role in controlling HBCD contamination in EPS/XPS.     

气相色谱-质谱法测定涂料中的六溴环十二烷

提出了用气相色谱-质谱法测定涂料中六溴环十二烷含量的方法。样品用二氯甲烷-丙酮(1+1)混合溶剂超声提取,提取液经硅胶固相萃取小柱净化、平行蒸发定量浓缩后,用DB-5MS毛细管柱进行分离,全扫描模式和选择离子监测模式测定。六溴环十二烷的质量浓度在1～50mg·L-1范围内与其峰面积呈线性关系,测定下限(10S/N)为10 mg·kg-1。添加5,20,50mg·L-1 3个浓度水平进行加标回收试验,回收率在82.0%～106%之间,测定值的相对标准偏差(n=8)在2.8%～5.3%之间。     

Stability of penicillin antibiotic residues in meat during storage. Ampicillin

Incurred samples from a pig treated with ampicillin, one of the most important penicillin antibiotic drugs used in food-producing animal treatments, were analyzed at the residue level of the drug in muscle tissue (approximately 100 microg kg(-1)) during their freezing storage and using three different techniques: quantitative microbiological assay, HPLC-UV and LC-MS. Two parameters have been specifically monitored: storage temperature (-20 and -75 degrees C) and storage packaging (ground meat or bulk meat). No significant decrease was observed during the first 3 months of storage monitoring at -20 and -75 degrees C. On the contrary, the sample preparation significantly affected the drug concentration in muscle from the very beginning of the storage. Grinding the meat before storage allowed to keep the drug near the higher level of concentration (approximately 100 microg kg(-1)) when bulk meat stored frozen systematically led to a decreased value (approximately 75 microg kg(-1)). After 8 months of storage at -20 degrees C, a significant decrease arose and was never observed at -75 degrees C. All the results were similarly obtained with the three different techniques used simultaneously, which allows to indicate a good correlation between the techniques.     

Use of aqueous slurry sampling for the determination of lead in human hair samples by electrothermal atomic absorption spectrometry

A method for the determination of lead in human hair slurries by electrothermal atomic absorption spectrometry was optimized. Particle size reduction was achieved with a vibrational mill ball equipped with zirconia cups, 20 min being sufficient grinding time to achieve an adequate particle diameter (<1 mum). The use of different thickening agents, namely glycerol, Triton X-100 and Viscalex HV30, was studied and glycerol was found to be the best. The use of Pd and Mg(NO(3))(2) at optimum concentrations of 20 and 25 mg l(-1) respectively was found to be satisfactory for stabilizing lead at 1100 degrees C. A limit of detection of 0.21 mg kg(-1) was obtained. The limit of detection can be reduced to 0.05 mg kg(-1) without loss of analytical performance by increasing four-fold the amount of hair sample. Accuracy was studied by analysis of a CRM 397 human hair reference material with a certified lead content of 33.0 +/- 1.2 mg Pb kg(-1). The standard addition method was used for the determination of lead in hair samples from healthy people, the levels being between 2.3 and 35.5 mg kg(-1).     

超高效液相色谱-串联四极杆质谱法检测小型家电外壳中的六溴环十二烷

建立了加热回流萃取-超高效液相色谱-串联四极杆质谱检测小型家用电器中六溴环十二烷( Hexabromocyclododecane,HBCD)的方法.实验优化了电子电器类产品的前处理方法,以甲苯-甲醇(10∶1,V/V)为萃取剂,加热回流4h.萃取出的溶液经N2吹干,初始流动相复溶,涡旋、离心、过膜,经ACQUITYTMUPLC BEH C18色谱柱分离;以甲醇-乙腈(4∶1,V/V)-10 mmol/L醋酸铵为流动相,质谱的多反应监测模式(MRM)进行检测,HBCD的3种同分异构体在3 min内完全分开.该物质的检山限为0.014 mg/L:定量限为0.068 mg/L;标准曲线的线性范围为1.6～ 32.4 mg/L,线性相关系数大于0.996,萃取回收率为68.0％～75.2％.通过外标法定量,并将本方法应用于实际样品(电视机外壳、电子相框、电磁炉外壳等)的检测.     

Methods for the determination of phenolic brominated flame retardants, and by-products, formulation intermediates and decomposition products of brominated flame retardants in water

Brominated flame retardants (BFRs) are the chemicals of high importance within the REAch framework. In addition to polybrominated diphenyl ethers (PBDEs), hexabromocyclododecane (HBCD) and tetrabromobisphenol A (TBBPA), other BFRs such as bromophenols, intermediates in FR formulation like bromoanilines, and their brominated and non-brominated by-products such as bromoanisoles, bromotoluenes, bromoalkanes and 1,5,9-cyclododecatriene, respectively should be monitored and controlled because of their toxicity and their very low odour and taste thresholds, below sub-nanogram-per liter levels. In the present study several analytical methods for the simultaneous determination, i.e., combining one single sample treatment and one analysis step, of these compounds in water have been developed, optimized and evaluated. The methods involve a (pre-concentration)-extraction technique, such as liquid-liquid (LLE), solid-phase (SPE), headspace (HS) extraction or solid-phase microextraction (SPME), followed by gas chromatography (GC)-mass spectrometry (MS) analysis with either electron capture negative ionization (ECNI) or electron impact (EI) as ionization techniques. ECNI is more sensitive than EI for analytes with more than one bromine atom. HS and SPME were previously optimized by means of a multifactorial experimental design. Extraction temperature and the liquid/headspace volume ratio were the most significant factors in HS extraction. In SPME, the variables studied were the nature of the fiber, the mode of extraction and the extraction temperature. Polydimethylsiloxane (PDMS) fibers appeared to be more suitable than carboxen-polydimethylsiloxane (CAR-PDMS) for the analysis of the target compounds with more than one bromine atom. The extraction of 2,4-dibromoaniline was only achieved in a direct immersion mode, in which the optimal extraction temperature was 60 degrees C. The methods LLE-GC-(ECNI)MS, LLE-GC-(EI)MS, SPE-GC-(ECNI)MS, SPE-GC-(EI)MS, HS-GC-(EI)MS and SPME-GC-(EI)MS were evaluated in terms of linearity, precision, detection limits and trueness. All methods, with the exception of HS-GC-(EI)MS, were linear in a range of at least two orders of magnitude, giving recoveries above 75% and detection limits at the low ng/L level for most of the target analytes. SPE-GC-(ECNI)MS is the most sensitive and reliable method for the determination of most of the bromine compounds, whereas SPE-GC-(EI)MS is the most suitable to quantify the three isomers of 1,5,9-cyclododecatriene. Both methods together with SPME-GC-(EI)MS (for qualitative confirmation) were applied to water samples from the Western Scheldt (The Netherlands), where 2,6-dibromophenol and 2,4,6-tribromoanisole could be detected at levels higher than their respective odour thresholds.     

4氯化铜对聚氯乙烯燃烧产物的催化作用

用现代色谱分析技术确定了在不同炉温条件下,掺杂有CuCl~2的聚氯乙烯燃烧过程中二噁英和多环芳烃的生成量,研究了氯化铜用量对其生成量的影响。结果表? 鞯ゴ康木勐纫蚁┤忌詹罅康亩嗷贩继蜕倭康亩f英,氯化铜的加入可大大增加二噁英的生成量,并能抑制多环芳烃的产生。金属氯化物可能是促使聚氯乙? ┤忌詹f英的主要因素之一。     

Investigation of hexabromocyclododecane thermal degradation pathways by gas chromatography/mass spectrometry

The decomposition products of hexabromocyclododecane (HBCD), a widely used brominated flame retardant, were investigated by gas chromatography/mass spectrometry (GC/MS). HBCD thermal degradation was conducted under a moderate heating rate (10 degrees C/min) in a batch reactor using both inert and oxidizing atmospheres. GC/MS analysis allowed the identification of substances derived from the primary pyrolysis process at the moderate heating rates used. The presence of oxygen seems to have a negligible influence on the degradation products obtained in HBCD decomposition, at least at moderate heating rates. Based on the identified products, the main pathways of HBCD thermal degradation were assessed and a mechanism for HBCD decomposition was proposed. The results obtained indicate that hexa-, penta- and tetrabrominated polyaromatic structures seem not to be primary products of HBCD decomposition, and may only be obtained by secondary bromination reactions.     

Determination of carbamate residues in fruits and vegetables by matrix solid-phase dispersion and liquid chromatography-mass spectrometry

Thirteen carbamates were analysed in orange, grape, onion and tomatoes by matrix solid-phase dispersion (MSPD) followed by liquid chromatography-mass spectrometry (LC-MS). Electrospray (ES) and atmospheric pressure chemical ionisation (APCI) were compared and both gave similar results in terms of sensitivity and structural information because at 20 V fragmentor voltages the fragmentation is minimal. The efficiency of different solid-phases (C18, C8, cyano, amine and phenyl) for the MSPD was compared. Mean recoveries using C8 varied from 64 to 106% with relative standard deviations of 5-15% in the concentration range of 0.01-10 mg kg(-1). Matrix constituents did not interfere significantly with the ionisation process of carbamates. The limits of detection were typically in the 0.001-0.01 mg kg(-1) range, which were between 10 and 100 times lower than the maximum residue levels (MRLs) established by the European Union (EU). The method was applied to residue detection in fruit and vegetable samples taken from Valencian markets, in which carbamates were detected at low concentrations.     

Electrospray ionization tandem mass spectrometric characterization of DNA adducts formed by bromobenzoquinones

Bromobenzoquinones (BBQs) represent a class of reactive metabolites of various aromatic contaminants with bromine-containing substituents, including bromobenzene, bromophenols, polybrominated diphenyl ethers (PBDEs). Recently, 2,6-dibromobenzoquinone also has been detected directly from drinking water. The alternation of the genome caused by covalent binding of chemicals or their metabolites to DNA provides a viable mechanism for carcinogenicity. In the present study, electrospray ionization coupled with ion trap mass spectrometry (ITMS), triple quadrupole MS or quadrupole time-of-flight MS was applied for the analysis of DNA adducts formed by BBQs. The study demonstrated 2-monobromobenzoquinone and 2,6-dibromobenzoquinone could covalently bind to deoxyguanosine (dG) and DNA in vitro. The chemical structures of the DNA adducts were confirmed by accurate mass values, collision-induced fragmentation tandem mass spectra as well as isotopic patterns. Generally, the reaction mechanism for the DNA adduction involved Michael addition between the electron-deficient carbon from the quinone and the nucleophilic exocyclic nitrogen from the dG followed by reductive cyclization with loss of a small molecule such as H(2)O, or HBrO. It was of particular interest to note that some adducts were generated from the reaction of one dG molecule with two BBQ molecules. The obtained results provided new information for assessing the potential cancer risk associated with bromobenzene, bromophenols, PBDEs and BBQs.     

直接衍生离子液体富集高效液相色谱分析水基胶中脂肪族醛酮

建立了以2,4-二硝基苯肼(DNPH)直接衍生,1-丁基-3-甲基咪唑六氟磷酸盐(［BMIM］PF6)萃取富集,高效液相色谱(HPLC)分析水基胶中痕量脂肪族醛酮的方法。分散的水基胶乳液用80 mg/L DNPH衍生化试剂(含0.44 mol/L磷酸)于40 ℃衍生18 min。取离心后的上层衍生液,加入0.5 mL ［BMIM］PF6于30 ℃萃取富集,离子液体相过滤后进行HPLC分析。采用Dionex Acclaim Explosives E2色谱柱(250 mm×4.6 mm, 5 μm),以水-乙腈为流动相在流速1.2 mL/min进行梯度洗脱,色谱柱温度为35 ℃,检测波长为365 nm。结果表明,8种脂肪族醛酮的检出限为0.022～0.221 mg/kg,定量限为0.073～0.738 mg/kg,相对标准偏差为3.5%～7.3%,回收率为84.0%～102.5%。与溶剂萃取法相比,该法具有检出限和定量限低、稳定性高、测定更准确的优势。     

Chemical modifiers for direct determination of cobalt in coal combustion residues by ultrasonic slurry-sampling-ETAAS

Five modifiers were tested for the direct determination of cobalt in coal fly ash and slag by ultrasonic slurry-sampling electrothermal atomic absorption spectrometry (USS-ETAAS).The furnace temperature programs and the appropriate amount for each modifier were optimized to get the highest signal and the best separation between the atomic and background signals. Nitric acid (0.5% v/v) was the most adequate chemical modifier for cobalt determination, selecting 1,450 degrees C and 2,100 degrees C as pyrolysis and atomization temperatures, respectively. This modifier also acts as liquid medium for the slurry simplifying the procedure. The remaining modifiers enhanced the background signal, totally overlapped with cobalt peak. The method optimized gave a limit of detection of 0.36 microg g(-1), a characteristic mass of 13 +/- 1 pg and an overall-method precision which is highly satisfactory (<7%, RSD). The method was validated by analyzing two certified coal fly ash materials, and satisfactory recoveries were obtained (83-90%) and no statistical differences were observed between the experimental and the certified cobalt concentrations. Additionally, certified sediment, soil and urban particulate matter were assayed; again good results were obtained. The developed methodology was used to determine cobalt in several coal combustion residues from five Spanish power plants.     

Analytical screening of polyadipates and other plasticisers in poly(vinyl chloride) gasket seals and in fatty food by gas chromatography-mass spectrometry

Fourteen poly(vinyl chloride) (PVC) gasket seals and 15 samples of pesto, tomatoes sauces, olive oil and olives in oil were analysed for the additives and plasticisers. The systematic screening of the representative samples revealed that epoxidised soybean oil (ESBO) was the principal plasticiser in eight gaskets and the concentrations of the substance ranged from 15% to 42%. Diisodecyl phthalate (DIDP) as main plasticiser was revealed in three samples and the amount ranged from 37 to 41%. Polyadipate was added in four samples at 16-46%. The concentration of ESBO exceeded 60 mg kg(-1) in three food samples with extreme at 281.9 mg kg(-1) and average 61.3 mg kg(-1). Di-(2-ethylhexyl) phthalate (DEHP) was detected in six food samples and it ranged from 2.5 to 8.7 mg kg(-1). The concentration of DEHP exceeded SML (3 mg kg(-1)) in five cases. The concentration of total polyadipate (PA) was 16.3 mg kg(-1) in average. All eight positive food samples for total PA showed the concentrations below SML (30 mg kg(-1)), which are specified for the fraction of polyadipates lower than 1000 Da. The migration rate of polyadipate in the food ranged from 1 to 7%. At such low transfer rate the polyadipates could be promising plasticisers for PVC gasket seals used in food industry.     

Variation in antioxidant attributes at three ripening stages of guava (Psidium guajava L.) fruit from different geographical regions of Pakistan

The present investigation was carried out to appraise the levels of total phenols and vitamin C as well as antioxidant potential at three different ripening stages (un-ripe, semi-ripe and fully-ripe) of guava (Psidium guajava L.) fruit collected from three different geographical regions of Pakistan (Islamabad, Faisalabad and Bhakkar). The antioxidant potential of guava fruit extracts was assessed by means of different in-vitro antioxidant assays, namely inhibition of peroxidation in linoleic acid system, reducing power and radical scavenging capability. Overall, fruit at the un-ripe stage (G1) exhibited the highest levels of TPC, TFC, reducing power and DPPH radical scavenging activity, followed by the semi-ripe (G2) and fully-ripe (G3) stages. On the other hand, vitamin C content increased as the fruit maturity progressed, with highest value seen at the fully-ripe stage (G3) followed by the semi-ripe (G2) and un-ripe stage (G1). The concentration of vitamin C in fruits varied as: Faisalabad (136.4-247.9 mg 100 g?1), Islamabad (89.7-149.7 mg 100 g?1) and Bhakkar (73.1-129.5 mg 100 g?1). The results showed that different stages of maturation and geographical locations had profound effects on the antioxidant activity and vitamin C contents of guava fruit.     

Interaction of gemini surfactants butane-1,4-diyl-bis(alkyldimethylammonium bromide) with DNA

The size and structure of aggregates formed by interaction of DNA with homologous series of cationic gemini surfactants butane-1,4-diyl-bis(alkyldimethylammonium bromide) (CnGS, n=10-16 is the number of alkyl carbons) were investigated using UV-vis turbidity, dynamic light scattering and small-angle synchrotron X-ray (SAX) diffraction. The detailed analysis of turbidity in the range of lambda=450-600 nm indicates an anomaly in the growth of CnGS+DNA aggregates with increasing concentration of CnGS, possibly involving changes of structure and size of aggregates. Using dynamic light scattering, changes of the effective diameter of CnGS+DNA (n=12 and 16) aggregates formed in the CnGS concentration range 0.002-0.140 mmol/l were observed. SAX diffractograms show the presence of long-range organization of CnGS+DNA (n=12, 13, 14 and 16) aggregates due to DNA interaction with CnGS above the critical micellar concentration. The CnGS+DNA (n=12, 13 and 14) aggregates at 25 degrees C are packed in a lattice of two-dimensional hexagonal symmetry. With increasing C14GS:DNA molar ratio the changes of the lattice parameter in the range of 4.80-5.27 nm are observed at 25 degrees C. The aggregates undergo structural changes induced by temperature in the range 60-95 degrees C, which are accompanied by changes of the diffraction patterns, namely in the region of reciprocal spacing s=0.15-0.30 nm(-1).     

Fluorine sorption by soils developed from various parent materials in Galicia (NW Spain)

Fluorine is a phytotoxic element that can reach the soil from various industrial activities. Fluorine sorption by soil is crucial to protect water and food chain from fluorine pollution. In Galicia (NW Spain), various activities emit fluorine into the atmosphere, mainly ceramic industries and an aluminium smelter. This study, aiming to investigate fluorine sorption by Galician soils, was conducted on natural soil horizons representative of the area. Most soils were acid and rich in organic matter and showed strong fluorine sorption. The lowest sorptions were exhibited by a near-neutral serpentinite-derived soil (1001 mg kg(-1)) and the B horizons of soils developed from quartz schist (989 mg kg(-1)), and the highest by the A horizons of amphibolite-derived soils (1783 mg kg(-1)). In soils developed from quartz schist, biotitic schist and amphibolite, A horizons sorbed more fluoride than the corresponding B horizons (average 1621 and 1324 mg kg(-1), respectively), while the opposite is true in granite-derived soils (average 1644 and 1324 mg kg(-1), respectively). In the A horizons, the F sorption significantly correlated to soil pH (r=-0.79), pH in NaF (r=0.83) and oxalate Al (r=0.81). In the B horizons, sorption correlated to soil pH (r=-0.78), oxalate Fe (r=0.71) and organic C (r=0.66). F sorption can be described by both the Langmuir and Freundlich equations. The concentration of free fluoride in the equilibrium solutions increased above pH 6.     

Determination of neonicotinoid pesticides residues in agricultural samples by solid-phase extraction combined with liquid chromatography-tandem mass spectrometry

This work reports a new sensitive multi-residue liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for detection, confirmation and quantification of six neonicotinoid pesticides (dinotefuran, thiamethoxam, clothiandin, imidacloprid, acetamiprid and thiacloprid) in agricultural samples (chestnut, shallot, ginger and tea). Activated carbon and HLB solid-phase extraction cartridges were used for cleaning up the extracts. Analysis is performed by LC-MS/MS operated in the multiple reaction monitoring (MRM) mode, acquiring two specific precursor-product ion transitions per target compound. Quantification was carried by the internal standard method with D(4)-labeled imidacloprid. The method showed excellent linearity (R(2)≥0.9991) and precision (relative standard deviation, RSD≤8.6%) for all compounds. Limits of quantification (LOQs) were 0.01 mg kg(-1) for chestnut, shallot, ginger sample and 0.02 mg kg(-1) for tea sample. The average recoveries, measured at three concentrations levels (0.01 mg kg(-1), 0.02 mg kg(-1) and 0.1 mg kg(-1) for chestnut, shallot, ginger sample, 0.02 mg kg(-1), 0.04 mg kg(-1) and 0.2 mg kg(-1) for tea sample), were in the range 82.1-108.5%. The method was satisfactorily validated for the analysis of 150 agricultural samples (chestnut, shallot, ginger and tea). Imidacloprid and acetamiprid were detected at concentration levels ranging from 0.05 to 3.6 mg kg(-1).