退火温度和退火气氛对Ni/Au与p-GaN之间欧姆接触性能的影响

研究了不同退火温度和气氛对Ni/Au与p-GaN之间欧姆接触性能的影响. 采用圆形传输线模型方法得到不同退火温度和不同退火气氛下的比接触电阻率. 结果表明, 较适宜的退火温度为500 ℃左右, 退火温度太高或太低都会导致比接触电阻率的增大; 较适宜的退火气氛为适量含氧的氮气气氛, 且氧气含量对比接触电阻率大小的影响并不显著. 经过对退火条件的优化, 得到的比接触电阻率可达7.65×10^-4 Ω·cm². 关键词： p-GaN 欧姆接触 圆形传输线模型 快速热退火     

金属与半导体Ge欧姆接触制备、性质及其机理分析

金属与Ge材料接触时界面处存在着强烈的费米钉扎效应, 尤其与n型Ge形成的欧姆接触的比接触电阻率高, 是制约Si基Ge器件性能的关键因素之一. 本文对比了分别采用金属Al和Ni 与Si衬底上外延生长的p型Ge和n型Ge材料的接触特性. 发现在相同的较高掺杂条件下, NiGe与n型Ge可形成良好的欧姆接触, 其比接触电阻率 较 Al接触降低了一个数量级, 掺P浓度为2×10¹⁹ cm^-3时达到1.43×10^-5 Ω·cm². NiGe与p型Ge接触和Al接触的比接触电阻率相当, 掺B浓度为4.2×10¹⁸ cm^-3时达到1.68×10^-5 Ω·cm². NiGe与n型Ge接触和Al电极相比较, 在形成NiGe过程中, P杂质在界面处的偏析是其接触电阻率降低的主要原因. 采用NiGe作为Ge的接触电极在目前是合适的选择. 关键词： 金属与Ge接触性质 NiGe 比接触电阻率     

硅衬底GaN基LED N极性n型欧姆接触研究

在Si衬底GaN基垂直结构LED的N极性n型面上,利用电子束蒸发的方法制作了Ti/Al电极,通过了I-V曲线研究了有无AlN缓冲层对这种芯片欧姆接触的影响.结果显示,去除AlN缓冲层后的N极性n型面与Ti/Al电极在500到600 ℃范围内退火才能形成欧姆接触.而保留AlN缓冲层的N极性n型面与Ti/Al电极未退火时就表现为较好的欧姆接触,比接触电阻率为2×10^-5 Ω·cm²,即使退火温度升高至600 ℃,也始终保持着欧姆接触特性.因此,AlN缓冲层的存在是Si衬底GaN基垂直结构LED获得高热稳定性n型欧姆接触的关键. 关键词： 硅衬底 N极性 AlN缓冲层 欧姆接触     

低接触电阻率Ni/Ag/Ti/Au反射镜电极的研究

研究了Ag的厚度、退火时间、沉积温度对于Ni/Ag/Ti/Au电极的反射率及与p-GaN欧姆接触性能的影响. 利用分光光度计测量反射率, 采用圆形传输线模型计算比接触电阻率. 结果表明: 随着Ag厚度的增加, Ni/Ag/Ti/Au电极的反射率逐渐增大; 在氧气氛围中, 随着退火时间从1 min增至10 min, 300 ℃退火时, 比接触电阻率持续下降, 而对于400-600 ℃退火, 比接触电阻率先减小后增大; 在300和400 ℃氧气中进行1-10 min 的退火后, Ni/Ag/Ti/Au的反射率变化较小, 退火温度高于400 ℃时, 随着退火时间的增加, 反射率急剧下降; 在400 ℃氧气中3 min退火后, 比接触电阻率可以达到3.6×10^-3 Ω·cm². 此外, 适当提高沉积温度可以增加Ni/Ag/Ti/Au的反射率并降低比接触电阻率, 沉积温度为120 ℃条件下的Ni/Ag/Ti/Au电极在450 nm处反射率达到90.1%, 比接触电阻率为6.4×10^-3 Ω·cm². 综合考虑电学和光学性能, 在沉积温度为120 ℃下蒸镀Ni/Ag/Ti/Au (1/200/100/100 nm)并在400 ℃氧气中进行3 min退火可以得到较优化的电极. 利用此电极制作的垂直结构发光二极管在350 mA电流下的工作电压为2.95 V, 输出光功率为387.1 mW, 电光转换效率达到37.5%.     

铜-钼源漏电极对非晶氧化铟镓锌薄膜晶体管性能的改善

在铜(Cu)和非晶铟镓锌氧化物(a-IGZO)之间插入30 nm厚的钼(Mo)接触层, 制备了具有Cu-Mo源漏电极的a-IGZO薄膜晶体管(TFT). Mo接触层不仅能够抑制Cu与a-IGZO有源层之间的扩散, 而且提高了Cu电极与玻璃基底以及栅极绝缘层的结合强度. 制备的Cu-Mo结构TFT与纯Cu 结构TFT相比, 具有较高的迁移率(～9.26 cm²·V^-1·s^-1)、更短的电流传输长度(～0.2 μm)、更低的接触电阻(～1072 Ω)和有效接触电阻率(～1×10^-4Ω·cm²), 能够满足TFT 阵列高导互联的要求.     

传输线模型测量Au/Ti/p型金刚石薄膜的欧姆接触电阻率

采用传输线模型测量了重B掺杂p型金刚石薄膜(约10²⁰cm^-3)上Ti/A u欧姆接触电阻率ρ_c,测试了500℃退火前后及大电流情况下的I-V特性,研究 了退火对ρ_c的影响.结果表明,重掺杂和退火工艺是改善欧姆接触的有效手段. ρ_c随测试温度的变化表明金属/半导体接触界面载流子输运机制为隧道穿透.而 光照对ρ_c影响的分析表明金刚石可作为理想窗口材料.测试得到的最低ρ _c值约为10^-4Ωcm². 关键词： 金刚石薄膜 欧姆接触 接触电阻率     

激光辐照对热退火金属/掺氟二氧化锡透明导电薄膜光电性能的影响

采用532 nm纳秒脉冲激光对热退火的铝(Al)/掺氟二氧化锡(FTO)、铜(Cu)/FTO和银(Ag)/FTO三种双层复合薄膜表面分别进行处理, 结果显示薄膜样品的光电性能都得到提高.其中, 热退火Ag/FTO薄膜的平均透光率(400–800 nm)增幅最大, 从72.6%提高到80.5%, 主要是由于其表面产生了具有减反增透作用的光栅结构.激光辐照后热退火Ag/FTO薄膜的导电性也略有提高, 其方块电阻从5.6 Ω/sq下降到5.3 Ω/sq, 原因主要是激光辐照的热效应造成的退火作用使薄膜的晶粒尺寸增大, 减少了晶界散射而使载流子迁移率提高.计算结果显示, 激光辐照后热退火Ag/FTO薄膜的品质因子从0.73×10^-2Ω^-1增大为2.16×10^-2Ω^-1, 表明其综合光电性能得到显著提高.激光辐照可同步实现薄膜表面光栅结构的制备和附加退火作用, 这为金属层复合透明导电薄膜光电性能的综合优化提供了新的思路.     

碲化铋红外透明导电薄膜的制备与光电性能（特邀）

采用射频磁控溅射法在石英衬底和硒化锌衬底上制备了碲化铋薄膜,分别研究了薄膜厚度、退火温度对薄膜微观结构和光电性能的影响。利用X射线衍射仪、X射线光电子能谱仪和冷场发射扫描电子显微镜,分析了薄膜结构、成分和形貌。结果表明,退火有利于薄膜的结晶,且不改变晶体的择优取向。傅里叶变换红外光谱测试结果表明,在石英衬底和硒化锌衬底上沉积的薄膜,光学透过率随着薄膜厚度和退火温度的增加而减小,在硒化锌衬底上沉积的薄膜透过波段比石英长,且光学透过率更加稳定。霍尔效应测试结果表明,随着薄膜厚度和退火温度的增加,薄膜的电阻率逐渐减小,最小为1.448×10^-3Ω·cm,迁移率为27.400 cm²·V^-1·s^-1,载流子浓度为1.573×10²⁰ cm^-3。在石英衬底上沉积的15 nm厚的Bi₂Te₃薄膜,在1～5μm波段的透过率达到80%,退火200℃后透过率达到60%,电阻率为5.663×10^-3Ω·cm。在...     

生长条件对脉冲激光沉积制备ZnO：Al薄膜光电性能的影响

本文研究了脉冲激光沉积(PLD)生长过程中, 铝掺量、氧压及衬底温度等实验参数对ZnO:Al(AZO)薄膜生长的影响, 并利用扫描电子显微镜、原子力显微镜、X射线衍射、霍尔效应、光透射光谱等实验手段对其透明导电性能进行了探讨. 变温霍尔效应和光透射测量表明, 当靶材中铝掺量大于0.5 wt%时, 所制备AZO薄膜中铝施主在80 K时已完全电离, 因Bernstein-Moss (BM) 效应其带隙变大, 均为重掺杂简并半导体. 进一步系统研究了氧压和衬底温度对AZO薄膜透明导电性能的影响, 实验发现当氧压为1 Pa, 衬底温度为200 ℃时, AZO 导电性能最好, 其霍尔迁移率为28.8 cm²/V·s, 薄膜电阻率最小可达2.7×10^-4 Ω·cm, 且在可见光范围内光透过率超过了85%. 氧压和温度的增加, 都会导致薄膜电阻率变大. 关键词： 脉冲激光沉积法 ZnO：Al薄膜 透光性 导电性     

TiAl3 和Ti/TiAl3 非合金化电极n型GaN欧姆接触的实现

在不进行合金化的情况下,首次直接采用TiAl3合金材料作为金属接触电极.在蓝宝石衬底上生长的n型载流子浓度为2×1018 cm-3的GaN上,成功地得到低接触电阻的欧姆接触,并由环形传输线模型方法测得比接触电阻率为3×10-5 Ω*cm2.与通常n型欧姆接触采用的Ti/Al双层结构比较,TiAl3合金结构更容易形成非合金化的n型欧姆接触.在此实验基础上,进一步分析了N空位和界面层处的TiAl3在形成非合金化或低温退火欧姆接触中发挥的作用,由此设计的Ti/TiAl3/Ni/Au接触结构,在TiAl3合金结构基础上明显地降低了接触电阻率.     

Ni/Au与N掺杂p型ZnO的欧姆接触

研究了Au,In,Ni/Au三种不同金属膜与N掺杂p型ZnO的接触特性,发现Ni/Au双层膜更适合作为其欧姆电极材料,并比较了不同气氛和不同温度退火对Ni/Au电极的影响.发现在O₂中退火电极性能发生蜕变,而在N₂中退火性能得到改善.指出即使在N₂中退火,退火温度的选择也是至关重要的,本实验在400℃,氮气气氛下退火150s,得到了较好的欧姆接触特性.     

Ta/Ni/Ta multilayered ohmic contacts on n-type SiC

The interface formation, electrical properties and the surface morphology of multilayered Ta/Ni/Ta/SiC contacts were reported in this study. It was found that the conducting behavior of the contacts so fabricated is much dependent on the metal layer thickness and the subsequent annealing temperature. Auger electron spectroscopy (AES) and X-ray diffraction analyses revealed that Ni₂Si and TaC formed as a result of the annealing. The Ni atoms diffused downward to metal/SiC interface and converted into Ni₂Si layer in adjacent to the SiC substrate. The released carbon atoms reacted with Ta atoms to form TaC layer. Ohmic contacts with specific contact resistivity as low as 3 × 10⁻⁴ Ω cm² have been achieved after thermal annealing. The formation of carbon vacancies at the Ni₂Si/SiC interface, probably created by dissociation of SiC and formation of TaC during thermal annealing, should be responsible for the ohmic formation of the annealed Ta/Ni/Ta contacts. The addition of Ta into the Ni metallization scheme to n-SiC restricted the accumulation of carbon atoms left behind during Ni₂Si formation, improving the electrical and microstructure properties.     

氢氟酸刻蚀对Ni/6H-SiC接触性质的作用

采用浓度为10%的氢氟酸（HF）刻蚀6H-SiC单晶片,研究了HF刻蚀时间对Ni/6H-SiC接触性质的影响．经24?h刻蚀的SiC基片在溅射Ni层后,其接触表现良好线性的电流-电压（I-V）曲线．低于这个腐蚀时间的接触具有明显的势垒,但在大于1000℃快速退火后,也得到了良好线性的I-V曲线．X射线衍射（XRD）和俄歇能谱（AES）深度元素分析表明Ni₂Si和C是快速退火后的主要产物．XRD和低能反射电子能量损失谱表明表层的C 关键词： 欧姆接触 SiC 富碳层 互扩散     

Protection of isolated and active regions in AlGaN/GaN HEMTs using selective laser annealing

Al Ga N/Ga N high-electron-mobility transistors with Au-free ohmic contacts are fabricated by selective laser annealing and conventional rapid thermal annealing. The current transport mechanism of ohmic contacts is investigated. Hightemperature annealing can be avoided in the isolated region and the active region by selective laser annealing. The implanted isolation leakage current is maintained 10-6 m A/mm even at 1000 V after selective laser annealing. On the contrary, hightemperature annealing will cause obvious degradation of the isolation. The morphology of Al Ga N surface is measured by atomic force microscope. No noticeable change of the Al Ga N surface morphology after selective laser annealing, while the root-mean-square roughness value markedly increases after rapid thermal annealing. The smaller frequency dispersion of capacitance–voltage characteristics confirms the lower density of surface states after selective laser annealing. Thus,dynamic on-resistance is effectively suppressed.     

Low specific contact resistivity to graphene achieved by AuGe/Ni/Au and annealing process

Low metal-graphene contact resistance is important in making high-performance graphene devices.In this work,we demonstrate a lower specific contact resistivity of Au_(0.88)Ge_(0.12)/Ni/Au-graphene contact compared with Ti/Au and Ti/Pt/Au contacts.The rapid thermal annealing process was optimized to improve AuGe/Ni/Au contact resistance.Results reveal that both pre- and post-annealing processes are effective for reducing the contact resistance.The specific contact resistivity decreases from 2.5 × 10~(-4) to 7.8 × 10~(-5) Ω·cm~2 by pre-annealing at 300 ℃ for one hour,and continues to decrease to9.5 × 10~(-7) H·cm~2 after post-annealing at 490 ℃ for 60 seconds.These approaches provide reliable means of lowering contact resistance.     

Mechanism of Ti/Al/Ni/Au ohmic contacts to AlGaN/GaN heterostructures via laser annealing

The physical mechanisms of Ti/Al/Ni/Au ohmic contacts to AlGaN/GaN heterostructures by laser annealing and rapid thermal annealing are systematically investigated. The microstructures indicate that a better surface morphology and an intact contact interface are formed after laser annealing. None of the TiN alloy spikes are formed at the interface of the laser annealing sample. The experimental results show that the current transport mechanism through the ohmic contact after laser annealing is different from the conventional spike mechanism, and it is dominated by thermionic field emission.     

Origin of ohmic behavior in Ni, Ni2Si and Pd contacts on n-type SiC

Ni, Ni₂Si and Pd contacts were prepared on n-type 4H-SiC and annealed in the temperature range of 750-1150 °C. The annealed contacts were analyzed before and after acid etching, and different features were found in unetched and etched contacts. Carbon left on the SiC surface after the acid etching of Ni₂Si contacts annealed at 960 °C was highly graphitized. In nickel contacts, the graphitization of interface carbon began at 960 °C and increased after annealing at higher temperatures. In palladium contacts, the onset of the interface carbon graphitization was observed after annealing at 1150 °C. For all three types of metallization, the minimal values of contact resistivity were achieved only when the sharp first-order peak at 1585 cm⁻¹ and distinct second-order peak at ∼2700 cm⁻¹ related to the presence of graphitized carbon were detected by Raman spectroscopy after the acid etching of contacts. The properties of unannealed secondary contacts deposited onto etched primary contacts were similar to the properties of the primary contacts unless carbon was selectively etched. The results show that ohmic behavior of Ni-based and Pd contacts on n-type SiC originates from the formation of graphitic carbon at the interface with SiC.     

Impact of Al addition on the formation of Ni germanosilicide layers under different temperature annealing

Solid reactions between Ni and relaxed Si_0.7Ge_0.3 substrate were systematically investigated with different Al interlayer thicknesses. The morphology, composition, and micro-structure of the Ni germanosilicide layers were analyzed with different annealing temperatures in the appearance of Al. The germanosilicide layers were characterized by Rutherford backscattering spectrometry, cross-section transmission electron microscopy, scan transmission electron microscopy, and secondary ion mass spectroscopy. It was shown that the incorporation of Al improved the surface and interface morphology of the germanosilicide layers, enhanced the thermal stabilities, and retarded the Ni-rich germanosilicide phase to mono germanosilicide phase. With increasing annealing temperature, Al atoms distributed from the Ni/Si_0.7Ge_0.3 interface to the total layer of Ni₂Si_0.7Ge_0.3, and finally accumulated at the surface of NiSi_0.7Ge_0.3. We found that under the assistance of Al atoms, the best quality Ni germanosilicide layer was achieved by annealing at 700 ℃ in the case of 3 nm Al.     

PdSi based ohmic contact on n-InP

The electrical and microstructural properties of the PdSi based ohmic contacts on n-InP are discussed in the research. A low specific contact resistance of 2.25 × 10⁻⁶ Ω cm² is obtained on Au/Si/Pd/n-InP contact after rapid thermal annealing (RTA) at 450 °C for 30 s. The low contact resistance can be maintained at the order of 10⁻⁶ Ω cm² even up to 500 °C annealing. From the Auger analysis, it is found that both the outdiffusion of In and the indiffusion of Si into the InP surface occurred at the ohmic contact sample. The formation of the Pd₃Si compound lowered the barrier of the contact. The reactions between Pd and InP of the contact, forming In vacancies, and leading the doping of Si to the InP contact interface.