电火花引发HEMA 接枝LDPE 薄膜及其血液相容性

采用接枝量、ATR－IR、SEM、与水接触角、溶血试验和再钙化时间等测试手段研究了电火花引发甲基丙烯酸β－羟乙酯(HEMA)表面接枝低密度聚乙烯(LAPE)薄膜的接枝聚合反应影响因素、表面结构和血液相容性。结果表明,电火花能有效引发HEMA在LDMA薄膜表面接枝聚合反应,随接枝聚合反应时间延长、单体浓度的增大。接枝量增大。随反应温度升高,接枝量增大到一最大值后,进一步升高反应温度,接枝量下降,最佳接枝聚合温度为60℃当在60℃单体φ=5％水溶液是反应2h时,经空气气氛和1.5kV电火花预处理72s和LDPE薄膜表面接枝量可达169ug/cm^2。接枝改性后LDPE薄膜与水的接触下降,亲水性增加,溶血程度减小,再钙化时间延长,血液相容性得到改善。     

电火花引发HEMA 接枝LDPE 薄膜及其血液相容性

采用接枝量、ATR－IR、SEM、与水接触角、溶血试验和再钙化时间等测试手段研究了电火花引发甲基丙烯酸β－羟乙酯(HEMA)表面接枝低密度聚乙烯(LAPE)薄膜的接枝聚合反应影响因素、表面结构和血液相容性。结果表明,电火花能有效引发HEMA在LDMA薄膜表面接枝聚合反应,随接枝聚合反应时间延长、单体浓度的增大。接枝量增大。随反应温度升高,接枝量增大到一最大值后,进一步升高反应温度,接枝量下降,最佳接枝聚合温度为60℃当在60℃单体φ=5％水溶液是反应2h时,经空气气氛和1.5kV电火花预处理72s和LDPE薄膜表面接枝量可达169ug/cm^2。接枝改性后LDPE薄膜与水的接触下降,亲水性增加,溶血程度减小,再钙化时间延长,血液相容性得到改善。     

聚酯薄膜表面接枝含硅氧烷共聚物及微生物黏附性研究

通过表面引发原子转移自由基聚合(SI-ATRP)在聚对苯二甲酸乙二醇酯(PET)薄膜表面接枝聚苯乙烯-聚二甲基硅氧烷嵌段共聚物(PET-g-PS-b-PDMS),制备具有强疏水性表面的聚酯薄膜.利用X-射线光电子能谱仪(XPS),傅里叶变换红外光谱仪(FTIR/ATR),场发射扫描电镜(FESEM)对改性前后聚酯薄膜的表面组成、结构和形貌进行分析与表征;利用接触角测试仪和微生物黏附实验对比研究接枝改性前后PET薄膜的润湿性和对微生物黏附性的影响.结果表明,随反应时间延长,聚酯薄膜表面接枝量增加,水接触角增大.当接枝聚合反应时间为12 h,接枝密度可达0.72 mg/cm2,接触角达到126°,薄膜表面细菌黏附量也随之降到最低.     

芴酮引发光接枝改性LDPE膜的研究

采用紫外光引发接枝表面改性的方法,以芴酮(FL)为引发剂,在低密度聚乙烯(LDPE)薄膜表面上接枝丙烯酸(AA)、甲基丙烯酸(MAA)、丙烯酸甲酯(MA)、甲基丙烯酸甲酯(MMA)、丙烯酰胺(AM)等单体,以赋予薄膜表面新的化学性质.考察了引发剂浓度、紫外光的辐照时间、辐照强度、单体种类对LDPE薄膜接枝程度的影响.结果表明,在一定范围内,增加芴酮浓度,可以提高单体的接枝率,但当芴酮浓度达到5%时,接枝率反而下降.延长辐照时间至4 min和提高紫外光的辐照强度达100 W/m2,均有利于接枝反应的进行.不同单体在LDPE膜上的接枝能力与单体的活性、单体与基材的相容性等因素有关.接枝后,LDPE与水的接触角下降程度不仅与单体在膜上的接枝量有关,还与接枝单体的亲水性能密切相关.     

电晕放电引发丙烯酸表面接枝LDPE薄膜的研究

本文采用接枝量测定、ATRIR和ESCA研究了电晕放电引发丙烯酸表面接枝LDPE薄膜,实验结果表明:电晕放电能有效地引发丙烯酸在LDPE薄膜表面的接枝聚合反应,随反应时间延长、反应温度提高和丙烯酸单体浓度增大,表面接枝量增大。当丙烯酸浓度为20%、聚合温度为70℃、反应15小时时,经电晕放电处理72秒后的LDPE薄膜表面接枝量高达22055μgcm2。     

表面温度敏感性聚酯薄膜的制备

通过在聚酯(PET)薄膜表面固定原子转移自由基聚合(ATRP)的引发基团,继而引发接枝聚N-异丙基丙烯酰胺(NIPAM),制备表面具有温度敏感性的聚酯薄膜.利用X射线光电子能谱仪(XPS),衰减全反射傅立叶变换红外光谱仪(FTIR/ATR),扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析与表征;利用接触角测试仪对比研究接枝改性前后PET薄膜的表面性能;研究数据表明,随着反应时间的延长,接枝到PET薄膜表面PNIPAM的量在增加.当接枝聚合反应时间为16 h,接枝量达到0.239mg/cm2.表明SI-ATRP具有一定的"活性"特征;接枝PNIPAM改性后的PET薄膜表现出对温度的刺激响应性.     

紫外光引发LDPE膜接枝含氟丙烯酸酯的研究

通过紫外光引发表面接枝聚合反应的方法 ,把含氟丙烯酸酯单体R 5 6 1 0引到LDPE薄膜上 .对经丁酮抽提后的接枝膜进行FTIR、ESCA、SEM和DSC等表征 ,证实含氟聚合物以化学键的方式接枝在LDPE基体膜上 .在一定范围内 ,增加紫外光强、引发剂和单体浓度以及反应温度等均有利于提高接枝率 .经计算R 5 6 1 0的紫外光引发接枝聚合反应总活化能为 5 4 2kJ mol.接枝膜的接触角随着接枝率的提高逐步增大 ,直至趋于恒定 .作者提出接枝膜存在一个在接触角测定时影响基体膜与探测水滴相互作用过程的边界层 .当接枝率较低、接枝层厚度小于边界层临界厚度时 ,基体LDPE影响接触角的大小 ,但随着接枝率提高 ,接枝层逐渐变厚 ,氟聚合物层对接触角的贡献逐渐占优势 ,导致接触角随之增大 .当接枝率超过一定值以后 ,接枝层厚度超过边界层临界厚度 ,接枝层对接枝膜的接触角起全部贡献 ,接触角测定值随之稳定     

表面引发接枝聚合法制备凹凸棒土/聚甲基丙烯酸甲酯杂化粒子的研究

将γ-氨丙基三乙氧基硅烷(APTES)接枝到凹凸棒土(AT)表面,制得表面键合伯氨基的改性粒子AT-APTES;通过AT-APTES表面的伯氨基和过硫酸铵(APS)构成氧化-还原引发体系,采用无皂乳液法实现甲基丙烯酸甲酯(MMA)在AT表面接枝聚合,制得最高接枝率为29.4%的杂化粒子AT-g-PMMA;采用红外光谱(FTIR)、拉曼光谱(Raman)、透射电镜(TEM)以及热失重分析(TGA)等方法对杂化粒子AT-g-PMMA进行了表征;研究了主要配方及工艺条件对表面引发接枝聚合接枝率的影响.结果表明,伯氨基-过硫酸铵引发体系可以有效引发MMA在AT表面接枝聚合,由于引发点位于AT表面,故接枝率较高.本研究体系适宜的温度为65℃,单体MMA用量为水质量的6%,APS用量为单体质量的1%,此工艺条件下可有效减小均聚反应对接枝聚合反应的影响.先接枝到AT表面的聚合物对后续的接枝聚合反应产生抑制作用,接枝率越高,抑制作用越大.     

表面接枝含氟苯乙烯共聚物的聚酯薄膜制备与表征

利用表面引发原子转移自由基聚合(SI-ATRP)在聚对苯二甲酸乙二醇酯(PET)薄膜表面接枝苯乙烯和4-氟苯乙烯的共聚物.研究不同反应时间和不同配比下接枝共聚物对聚酯薄膜表面组成、结构和性能的影响.通过傅利叶变换红外光谱仪(ATR/FTIR),X-射线光电子能谱仪(XPS),凝胶渗透色谱(GPC)和扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析;利用接触角测试和表面能计算对比研究接枝改性前后PET薄膜的表面性能.结果表明反应时间和单体百分含量对接枝百分率及接触角有一定的影响,随着反应时间的增长,聚酯薄膜表面接枝百分率增大,接触角增加,表面自由能下降.     

SMA高级醇酯的合成及其对HDPE表面的改性

以苯乙烯-马来酸酐共聚物(SMA)为骨架,通过酯化反应,在SMA上接枝不同链长的高级脂肪醇侧链,制备了一系列大分子表面改性剂。将SMA及其高级醇酯化物与高密度聚乙烯(HDPE)进行共混,利用全反射红外光谱(FT-IR-ATR)及水接触角对共混体系的表面特性进行了研究。结果表明:在较低添加量范围内(w≤0.04),SMA的高级醇酯化物可以在HDPE薄膜的表面择优富集,可明显降低薄膜的水接触角,提高薄膜的表面能。     

Surface modification of SPEU films by ozone induced graft copolymerization to improve hemocompatibility

Surface modification of segmented poly(ether urethane) (SPEU) by graft copolymerization with N,N′-dimethyl-N-methacryloyloxyethyl-N-(3-sulfopropyl) ammonium (DMMSA), a zwitterionic sulfobetaine structure, was conducted. A simple two-step procedure for grafting of DMMSA onto the surface of SPEU film was used. The surface was first treated with ozone to introduce active hydroperoxide groups. The active surface was then exposed to the DMMSA solution in the sealed tube. Grafted SPEU film was characterized by ATR–FTIR, XPS and contact angle measurement. ATR–FTIR and XPS investigations confirmed the graft copolymerization. The monomer concentration, copolymerization temperature and time were varied to maximize the efficiency of DMMSA grafting. The equilibrium water content (EWC) and contact angle measurements showed that the hydrophilicity of the film had been greatly improved. The blood compatibility of the grafted films was evaluated by platelet adhesion in platelet rich plasma (PRP), deposits in blood control and protein adsorption in bovine fibrinogen using SPEU film as the control. No platelet adhesion and no thrombus were observed for the grafted films incubated in PRP for 300 min and in blood for 120 min, respectively. The protein adsorption was reduced on the grafted films after incubation in bovine fibrinogen for 120 min. These results proved that improved blood compatibility was obtained by grafting this new zwitterionic sulfobetaine structure monomer onto SPEU film.     

铈盐引发聚醚氨酯膜上丙烯酰胺接枝聚合反应

由聚四亚甲基醚二醇、4,4′-二苯基甲烷二异氰酸酯与乙二胺或丁二醇扩链剂合成的聚醚氨酯薄膜,可顺利地在室温下用硝酸铈铵引发接枝丙烯酰胺共聚合反应,这可以从反应后的薄膜由起始时是透明的而变为不透明,也可以从接枝后的薄膜比基膜有较大的吸水率,以及从扫描电子显微镜观察到薄膜表面上有凸起图象的高分子链所证实,由于先发生接枝共聚合而后才是均聚反应,因而保证了接枝后的薄膜几乎不附着聚丙烯酰胺。     

Improving hydrophilicity and protein antifouling of electrospun poly(vinylidenefluoride-hexafluoropropylene) nanofiber membranes

<正>Poly(vinylidenefluoride-hexafluoropropylene)(PVDF-HFP) nanofiber membranes with improved hydrophilicity and protein fouling resistance via surface graft copolymerization of hydrophilic monomers were prepared.The surface modification involves atmospheric pressure glow discharge plasma(APGDP) pretreatment followed by graft copolymerization of poly(ethylene glycol) methyl ether methacrylate(PEGMA).The success of the graft modification with PEGMA on the PVDF-HFP fibrous membrane is ascertained by X-ray photoelectron spectroscopy(XPS) and attenuated total reflectance Fourier transform infrared measurements(ATR-FTIR).The hydrophilic property of the nanofiber membranes is assessed by water contact angle measurements.The results show that the PEGMA grafted PVDF-HFP nanofiber membrane has a water contact angle of 0°compared with the pristine value of 132°.The protein adsorption was effectively reduced after PEGMA grafting on the PVDF-HFP nanofiber membrane surface.The PEGMA polymer grafting density on the PVDF-HFP membrane surface is measured by the gravimetric method,and the filtration performance is characterized by the measurement of water flux.The results indicate that the water flux of the grafted PVDF-HFP fibrous membrane increases significantly with the increase of the PEGMA grafting density.     

N-甲基丙烯酰-N′-甲基哌嗪在嵌段聚醚氨酯膜上的Co~(60)-γ辐射接枝的研究

<正> 用亲水性单体对嵌段聚醚氨酯(SPEU)膜接枝共聚以改善其抗凝血性能,在医用材料的研究中已引起普遍重视,但由于一般化学方法接枝引发系统中带入的小分子常常对产品的医用性质造成不利的影响。我们曾报道通过Co~(60)-γ射线预辐照法用亲水性单体对以PTMG;MDI与不同的二胺类扩链剂制备的SPEU膜接枝共聚。本文在此基础上选用了两种单体AMP和MAMP。     

N-甲基丙烯酰-N′-甲基哌嗪在嵌段聚醚氨酯膜上的Co60-γ辐射接枝的研究

The graft copolymerization of N-methacryl-N'-methyl-opiperazine onto segmented polye-therurethane (SPEU) film by Go⁶⁰-r-preirradiation has been studied. It is found that the grafting time varies with structure of different chain extenders. The grafted substrated become opaque, the contact angle drops down and from SEM photographs with salient micrograph showing grafts of macrochain on the surface of SPEU film.     

Characterization of N-isopropyl acrylamide/acrylic acid grafted polypropylene nonwoven fabric developed by radiation-induced graft polymerization

Radiation-induced graft copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AA) mixture was carried out on polypropylene nonwoven fabric to develop a thermosensitive material and has been found to affect the thermal and physical characteristics of fabric. The grafted fabrics with different monomer ratios were characterized by thermal gravimetric analysis (TGA), fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), contact angle and atomic force microscopy (AFM). Results of FTIR clearly indicated that poly(acrylic acid) and poly(N-isopropyl acrylamide) were successfully grafted onto the membrane surface. TGA results showed that the thermal stability of PP fabric increased after grafting of NIPAAm/AA. The crystallinity values from DSC and XRD were found to decrease with increase in degree of grafting because of the addition of grafted chains within the noncrystalline region. The decrease in contact angles of the grafted fabric with an increase of the degree of grafting shows that PNIPAAm/PAA exists as the hydrophilic component. The increase in surface roughness after grafting was observed by AFM.     

血液相容材料的合成研究Ⅷ.磺铵两性离子单体在聚醚氨酯表面的臭氧活化接枝

生物相容性 ,特别是血液相容性是生物医用材料极其重要的性能[1] .提高不凝血性一直是生物材料研究与发展 (Ｒ Ｄ)的主要内容之一 ,半个多世纪来 ,不凝血材料的Ｒ Ｄ已取得了很大的发展[2 ] .但还不能满足心血管植入物 (Ｃａｒｄｉｏｖａｓｃｕｌａｒｉｍｐｌａｎｔｓ)及心血管医物 (Ｃａｒｄｉｏｖａｓｃｕｌａｒｄｅｖｉｃｅｓ)对不凝血性的需要 .Ｒａｔｎｅｒ[3 ] 在最近一次的血液相容性问题研讨会上再次强调了不凝血材料研究的紧迫性 .会议的报告也反映了该领域的研究现状 ,并提出了今后要研究的问题等 .目前不凝血性较好的材料仅有聚…     

Hydrophilic Modification of Microporous Polysulfone Membrane via Surface‐Initiated Atom Transfer Radical Polymerization and Hydrolysis of Poly(glycidylmethacrylate)

Poly(glycidylmethacrylate) (PGMA) brushes were grafted from chloromethylated polysulfone (CMPSF) membrane surface by surface‐initiated atom transfer radical polymerization (SI‐ATRP), and the grafting was followed by hydrolysis of epoxy groups in the grafting chains to improve the membrane's hydrophilic property. Fourier transform infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS) measurements confirmed the successful grafting and hydrolysis of PGMA. The grafting degree of the monomer, measured by periodic acid titration and gravimetric analysis, increased linearly with the polymerization time, while the static water contact angle of the membrane grafted with PGMA or hydrolyzed PGMA linearly decreased. In comparison with the PGMA‐grafted membranes, the hydrolyzed PGMA‐grafted membranes possess stronger hydrophilicity as indicated by their contact angle and hydration capacity, and as a result they have an improved antifouling property. Therefore, the control of the hydrophilicity of PSF membrane could be realized through adjusting the polymerization time and transforming the functional groups in the grafting chain.     

Functionalization of polyethylene surface using plasma-induced graft copolymerization of acrylic acid

Plasma-induced graft copolymerization of acrylic acid onto PE films was investigated. The influence of plasma treatment power, pressure, time, graft copolymerization time, and monomer concentration on polymerization yield was determined. A chemical shift of the Cls signal of Ar plasma treated and untreated PE films was revealed by ESCA, which also verified the presence of grafted PAAc. An increase in graft polymerization yield with plasma treatment time and power was found. Both the plasma treated film and the subsequently grafted film were shown to be hydrophilic. Only the grafted film, however, shows an invariably low contact angle. The decomposition of peroxides upon heating was followed by a simple first-order reaction. © 1993 John Wiley & Sons, Inc.