碳掺杂的二氧化钛纳米管的制备及其可见光催化性能

以尿素作为碳元素前驱体对TiO2纳米管进行掺杂,采用比表面积测定、X射线衍射、透射电子显微镜、能量色散X射线荧光光谱、X射线光电子能谱、固体漫反射紫外-可见吸收光谱和荧光光谱对产物进行了表征。 结果表明,以尿素作为前驱体可制备C掺杂的TiO2纳米管,C掺杂后,TiO2纳米管的可见光催化活性明显提高。 此外,研究了C掺杂量、煅烧温度、催化剂用量和pH值对TiO2纳米管光催化降解活性的影响,发现当C的掺杂量为5.3%、催化剂用量为1.5 g/L、溶液的pH值为5时,在其催化作用下,可见光光照3 h后罗丹明B的降解率可达到91%。     

Ag@AgCl修饰TiO2-xCx光催化剂的制备及其可见光降解污染物性能

以钛酸丁酯和葡萄糖为原料用水热法制备了碳掺杂二氧化钛,再进一步对其进行Ag@AgCl表面修饰.用X射线衍射(XRD),X射线光电子能谱(XPS),透射电镜(TEM),BET比表面仪和紫外-可见(UV-Vis)漫反射光谱等手段对样品进行测试表征;在可见光辐射下(λ＞420 nm),以甲基橙和苯酚溶液的光催化降解实验来评价样品的活性.结果表明:经Ag@AgCl修饰后,样品的粒径增大,比表面积减小,对可见光的响应增强;可见光光催化效率有大幅度提高,对甲基橙和苯酚的降解效率分别是修饰前的5.5和3.4倍,且光催化剂经三次循环使用后活性基本保持不变.     

Change of adsorption modes of dyes on fluorinated TiO2 and its effect on photocatalytic degradation of dyes under visible irradiation

Surface-fluorinated TiO2 (F-TiO2) particles were prepared via the HF etching method. The surface characteristics of fluorinated TiO2, the adsorption modes of dyes, and the reaction pathways for the photocatalytic degradation of dye pollutants under visible light irradiation were investigated. It was found that, in the treatment of TiO2 by HF etching, F(-) not only displaces surface HO(-) but also substitutes some surface lattice oxygen. Using zwitterionic Rhodamine B (RhB) dye as a model, the change of the adsorption mode of RhB on F-TiO2 relative to that on pure TiO2 was validated by adsorption isotherms, X-ray photoelectron spectroscopy (XPS), and IR techniques for the first time. RhB preferentially anchors on pure TiO2 through the carboxylic (-COOH) group, while its adsorption group is switched to the cationic moiety (-NEt 2 group) on F-TiO2. Both the photocatalytic degradation kinetics and mechanisms were drastically changed after surface fluorination. Dyes with positively charged nitrogen-alkyl groups such as methylene blue (MB), malachite green (MG), Rhodamine 6G (Rh6G), and RhB all underwent a rapid N-dealkylation process on F-TiO2, while on pure TiO2 direct cleavage of dye chromophore ring structures predominated. The relationship between surface fluorination and the degradation rate/pathway of dyes under visible irradiation was also discussed in terms of the effect of fluorination on the surface adsorption of dyes and on the energy band structure of TiO2.     

乙酸修饰Ag/TiO2复合光催化剂的制备及协同催化性能

利用光化学还原法制备了Ag/TiO₂,然后通过乙酸浸渍制备了HAc-Ag/TiO₂复合光催化剂.利用X射线衍射（XRD）、透射电子显微镜（TEM）、傅里叶变换红外光谱（FTIR）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）等手段表征了催化剂的性质.以降解水溶液中的甲基橙（MO）为探针反应,考察了催化剂在可见光下的光催化性能.结果表明,乙酸对TiO₂的修饰在TiO₂禁带中产生了"带尾",使TiO₂的禁带宽度发生了显著的缩减;Ag纳米粒子和乙酸共同修饰的HAc-Ag/TiO₂样品具有更窄的禁带宽度和更正的价带顶位置;Ag和乙酸的协同作用使HAc-Ag/TiO₂具有良好的可见光催化活性：可见光照射2 h后,甲基橙在HAc-Ag/TiO₂上的降解率接近100%.     

C-N-S-TiO2光催化剂的制备、表征及其性能

以钛酸四丁酯为钛源、功能生物小分子胱氨酸为掺杂剂,采用溶胶-凝胶法同步合成了C-N-S-TiO2光催化剂,利用XRD、XPS、FT-IR和DRS等测试技术对样品的结构及物化性能进行了表征。XRD和DRS分析表明,共掺杂抑制了TiO2晶粒的生长,提高了晶相转变温度,且C-N-S-TiO2样品的吸收带边明显"红移",光吸收范围一直延长至800 nm左右。XPS分析结果显示,C-N-S-TiO2样品表面产生了杂质能级,C、S元素分别取代部分晶格Ti4+以CO23-和S6+形式存在;而N峰呈宽化状态,以O—Ti—N和Ti—O—N键存在,且样品表面羟基含量明显增加。以罗丹明B染料为模型污染物,考察了该催化剂的可见光催化活性。结果表明,与P25 TiO2比较,C-N-S-TiO2光催化剂活性得到改进,C-N-S-TiO2光催化剂在470～800 nm波长下辐射120 min后对罗丹明B的降解率可高达83%。     

Mesoporous Fe2O3-doped TiO2 nanostructured fibers with higher photocatalytic activity

Mesoporous Fe(2)O(3)-doped TiO(2) nanostructured fibers were fabricated through electrospinning the relevant gel precursor. The prepared fibers were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and surface analysis, respectively. The photocatalytic activity of these mesoporous composite fibers was evaluated by photocatalytic degradation of methylene blue (MB) in water under UV irradiation. Compared with different types of photocatalysts, the 1% Fe(2)O(3)-doped TiO(2) fibers exhibited super photocatalytic activity.     

Fabrication of titanium dioxide and tungstophosphate nanocomposite films and their photocatalytic degradation for methyl orange

Photocatalytic multilayer films with different numbers of bilayers were prepared via an electrostatic layer-by-layer (LbL) self-assembly method. These LbL films were characterized by UV-vis spectroscopy, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). Our results indicate that TiO(2) and tungstophosphate (H(3)PW(12)O(40), abbreviated as PW(12)) are successfully incorporated into the thin films. The as-prepared (TiO(2)/PW(12))(n) films show good photocatalytic performance toward methyl orange (MO) solution at pH 2.0, which is attributed to the synergistic effect between TiO(2) and PW(12). The effect of experimental parameters including number of bilayers, initial concentration, and pH value of dye solution were also studied. The multilayer films can be easily recovered and reused several times with little change of degradation, indicating that they are stable under the ultraviolet (UV) irradiation. The detection of active species displays that active holes (h(+)) play a dominant role for MO photodegradation in the TiO(2)/PW(12) system. Taking advantage of immobilization of catalysts on glass slides, the problem of recovery is solved. It is expected that photocatalytic multilayer films have substantial applications in industry.     

Synthesis of Mg-Doped TiO2 nanoparticles under different conditions and its photocatalytic activity

In this study, TiO(2)- and Mg-doped TiO(2) nanoparticles with different dopant contents were prepared by sol-gel method. The prepared photocatalysts were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET) and diffuse reflectance spectroscopy (DRS) techniques. The results of BET analysis indicated a pore diameter of 8 nm and surface area of 48.5 m(2) g(-1). XRD patterns of pure and doped TiO(2) nanoparticles at 450 °C revealed that all phases are anatase. The particle size obtained from TEM was less than 20 nm. The band gap energy of Mg-doped TiO(2) nanoparticles was lower than that of TiO(2) . The photocatalytic activity of the pure and doped nanoparticles has been compared in the removal of C.I. Acid Red 27 (AR27). The photocatalytic activity of Mg-doped (0.2 mol%) TiO(2) for the degradation of AR27 was higher than that of bare TiO(2) nanoparticles. Results of total organic carbon analysis and changes in the AR27 UV-Vis peaks indicated 99% mineralization and extinguishing of all peaks in UV and visible regions is possible with Mg-doped TiO(2) nanoparticles. Removal efficiency of AR27 was sensitive to the parameters such as catalyst dose, pollutant concentration and light intensity.     

A simple route for the preparation of Eu, N-codoped TiO2 nanoparticles with enhanced visible light-induced photocatalytic activity

A simple route has been developed for the synthesis of europium, nitrogen-codoped titania photocatalysts under mild conditions (i.e., low temperature, < or = 348 K, and ambient pressure). The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and diffuse reflectance spectra (DRS) analyses. The results showed that the codoped photocatalyst with a spheroidal shape exhibited a smaller size than the undoped titania. The transformation from anatase to rutile was suppressed by doping with Eu and N atoms. Furthermore, the absorbance spectra of Eu, N-codoped TiO(2) exhibited a significant red shift to the visible region. The photocatalytic activity of Eu, N-codoped TiO(2) was evaluated by photodegradation of the dye reactive brilliant red X-3B under visible light. This codoped sample exhibited enhanced photocatalytic activity compared to N-doped TiO(2), pure TiO(2), and P25.     

Fe掺杂对纳米TiO2薄膜的结构与光催化性能的影响

采用溶胶-凝胶法制备了Fe掺杂的TiO2薄膜,利用X射线光电子能谱、X射线衍射技术、显微共聚焦拉曼光谱、紫外可见光谱和原子力显微镜等对薄膜进行表征,以甲基橙为反应模型对光催化活性进行测试。 结果表明,在300~600 ℃焙烧时,TiO2以锐钛矿结构存在,700 ℃焙烧时出现金红石结构。 随掺铁量和焙烧温度的增加,Fe/TiO2薄膜的表面粗糙度和晶粒尺寸均逐渐增大;随镀膜层数的增加,Fe/TiO2薄膜光谱吸收向可见光方向移动;较低含量的铁掺杂改善了TiO2薄膜的光催化活性,而较高含量的铁掺杂则使TiO2薄膜的光催化活性下降,掺铁量为0.1%时Fe/TiO2薄膜的光催化活性最好。     

Electrospun nanofibers of TiO2/CdS heteroarchitectures with enhanced photocatalytic activity by visible light

Herein, we have demonstrated that the electrospun nanofibers of TiO(2)/CdS heteroarchitectures could be fabricated through combining electrospinning technique with hydrothermal process. The configuration, crystal structure, and element composition of the as-prepared TiO(2)/CdS heteroarchitectures were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), X-ray diffraction (XRD), resonant Raman spectrometer, X-ray photoelectron spectroscopy (XPS). The results indicated that the high-density hexagonal wurtzite CdS crystalline particles of ca. 6-40 nm in diameter were uniformly and closely grown on anatase TiO(2) nanofibers. Especially, the light-absorption properties as well as photocatalytic characteristics of pure TiO(2) nanofibers and TiO(2)/CdS heteroarchitectures with different amount loading of CdS were also investigated. The absorption of TiO(2)/CdS heteroarchitectures was extended to the visible due to effective immobilization of sensitizing agent CdS on TiO(2). In contrast with the pure TiO(2) nanofibers, the TiO(2)/CdS heteroarchitectures showed excellent photocatalytic activity by using rhodamine B dye as a model organic substrate under visible-light irradiation. It was worth noting that the cooperative photocatalytic mechanism of the TiO(2)/CdS heteroarchitectures was also discussed.     

The effects of some operational parameters in photodegradation of benzylamine and aniline and their kinetics in aqueous suspension of TiO2 and Pt -loaded TiO2

Photocatalytic degradation of benzylamine and aniline on TiO2, Pt-modified TiO2, ZnO and ZnS in aqueous solution has been investigated. The degradation of the compounds follows a pseudo-first-order kinetics according to Langmuir-Hinshelwood model. The degradation process of benzylamine and aniline was evaluated by ninhydrin spectrophotometric method using UV-visible spectrophotometer in lambda(max) = 538 and 525 nm, respectively. The results showed the order of Pt/TiO2 > TiO2 > ZnO > ZnS for photocatalytic activity. In addition increasing of the Pt-loading was found to enhance the degradation rate of the compounds up to the optimal amount of 5 wt. % onto the surface of TiO2 so that the rates of degradation were increased about two times. Rate constants for photodegradation of benzylamine and aniline were found to be 1.4 x 10(-3) min(-1) and 0.7 x 10(-3) min(-1) for TiO2 as photocatalyst, while 2.7 x 10(-3) min(-1) and 1.7 x 10(-3) min(-1) for (5 wt.%) Pt/TiO2 as photocatalyst. Running the reactions in various pH (5-11), indicated that the pH = 8 and 10 or Higher are the optimum pH for photocatalytic degradation of benzylamine and aniline respectively. The effects of some other parameters such as amount of photocatalyst, flux of oxygen and irradiation time were evaluated. Furthermore, the Langmuir-Hinshelwood rate constant k(r) and adsorption constant K(A) for the titled compounds are reported.     

Characterization and mechanism analysis of Mo-N-co-doped TiO2 nano-photocatalyst and its enhanced visible activity

In this study, Mo-N-co-doped TiO(2) nano-photocatalysts have been synthesized through hydrolysis-precipitation method, combined with sonication posttreatment. The resulting materials were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and UV-vis diffuse reflectance spectroscopy (UV-vis DRS). XRD showed that co-doping with Mo and N favored the formation of anatase and retarded the growth of crystallite size. XPS revealed that N was incorporated into the lattice of TiO(2) through substituting oxygen atoms and coexisted in the forms of β-N and γ-N in co-doped TiO(2). Meanwhile, Mo was also incorporated into the lattice of TiO(2) through substituting titanium atoms and existed in the form of Mo(6+). DRS indicated that the light absorbance in visible region was improved by co-doping with Mo and N, leading to a narrower band gap and higher visible light photocatalytic activity for the degradation of phenol than that of pure and N-doped TiO(2). The enhanced visible light photocatalytic activity of Mo-N-co-doped TiO(2) nano-photocatalyst was attributed to the small crystallite size, narrow band gap and intense light absorbance in visible region. This study provides a new method to synthesize visible light active TiO(2)-based photocatalyst.     

Photocatalytic hydrogen production over CuO-modified titania

Efficient hydrogen production and decomposition of glycerol were achieved on CuO-modified titania (CuO-TiO(2)) photocatalysts in glycerol aqueous solutions. CuO clusters were deposited on the titania surface by impregnation of Degussa P25 TiO(2) powder (P25) with copper nitrate followed by calcination. The resulting CuO-TiO(2) composite photocatalysts were characterized by X-ray diffraction (XRD), UV-visible spectrophotometry, X-ray photoelectron spectroscopy (XPS), N(2) adsorption-desorption, transmission electron microscopy (TEM) and photoluminescence (PL) spectroscopy. The low-power ultraviolet light emitting diodes (UV-LED) were used as the light source for photocatalytic H(2)-production reaction. A detailed study of CuO effect on the photocatalytic H(2)-production rates showed that CuO clusters can act as an effective co-catalyst enhancing photocatalytic activity of TiO(2). The optimal CuO content was found to be 1.3 wt.%, giving H(2)-production rate of 2061 μmolh(-1)g(-1) (corresponding to the apparent quantum efficiency (QE) of 13.4% at 365 nm), which exceeded the rate of pure TiO(2) by more than 129 times. The quantum size effect of CuO clusters is deemed to alter its energy levels of the conduction and valence band edges in the CuO-TiO(2) semiconductor systems, which favors the electron transfer and enhances the photocatalytic activity. This work shows not only the possibility of using CuO clusters as a substitute for noble metals in the photocatalytic H(2)-production but also demonstrates a new way for enhancing hydrogen production activity by quantum size effect.     

Synthesis of a hybrid assembly composed of titanium dioxide nanoparticles and thin multi-walled carbon nanotubes using "click chemistry"

A hybrid assembly composed of thin multi-walled carbon nanotubes (t-MWCNT) and titanium dioxide (TiO(2)) has been prepared by using "click" chemistry for photocatalytic applications. TiO(2)-decorated t-MWCNT hybrids with anatase phase TiO(2) were obtained from the reaction of an azide moiety-containing TiO(2) with alkyne-functionalized t-MWCNTs. The hybrids were systematically characterized using Fourier transform infrared spectroscopic (FT-IR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectrum (EDX), and X-ray diffraction (XRD) measurements. The nanohybrid has been proved to be highly active and robust for photocatalytic degradation of methyl orange. The click coupling approach is a simple and convenient route to efficiently assemble TiO(2) on the surface of carbon nanotubes, and can be extended to obtain many other nanoparticle hybrids based on carbon nanotubes.     

铕掺杂TiO2的制备及其可见光光催化性能研究

采用溶胶-凝胶法制备了不同铕(Eu)掺杂量的TiO₂纳米颗粒(Eu-TiO₂),利用透射电镜(TEM),X射线光电子能谱(XPS),X射线衍射(XRD)及紫外可见漫反射(UV-Vis DRS)等方法对Eu-TiO₂进行了物理特性的初步表征.结果表明:与未掺杂纳米TiO₂比较,Eu-TiO₂禁带宽度变窄,具有可见光光催化活性.在可见光下(λ≥420 nm)照射下,以光催化降解染料罗丹明B(Rhodamine B,RhB)为目标反应,探讨了Eu-TiO₂不同制备条件对RhB降解光催化活性的影响,优化得到制备高活性Eu-TiO₂最佳pH为3、掺杂比例(n_Eu/n_Ti)为0.05%、煅烧温度为500 ℃.研究了可见光照射下Eu-TiO₂降解RhB和无色有机小分子水杨酸(SA)光催化反应条件及降解特性,RhB的12 h深度氧化矿化率为60.2%,SA的8 h降解率达到100%.通过跟踪测定可见光下Eu-TiO₂光催化反应过程中氧化物种的变化,研究了可见光激发Eu-TiO₂光催化反应机理,表明其光催化反应主要涉及羟基自由基(·OH)历程.     

水热pH值对溴氧化铋组成、形貌及光催化性能的影响

通过调节pH值一步水热法制备溴氧化铋光催化剂,并利用X射线衍射（XRD）、扫描电镜（SEM）、紫外-可见漫反射光谱（UV-vis DRS）和固体荧光光谱（PL）等方法对其进行表征。在可见光（γ>420 nm）照射下,通过对水溶液中罗丹明B,甲基橙和苯酚的降解效果来评价溴氧化铋的光催化活性。结果表明,由于B9提高了对可见光的吸收以及电子-空穴对的分离效率,B9具有最好的光催化活性,同时探索水热pH值对制备溴氧化铋的形貌和组成的影响,并说明了不同水热pH值下溴氧化铋的合成过程。     

Fe2O3/ZnO/ZnFe2O4 composites for the efficient photocatalytic degradation of organic dyes under visible light

In this study, novel ternary Fe₂O₃/ZnO/ZnFe₂O₄ (ZFO) composites were successfully prepared through a simple hydrothermal reaction with subsequent thermal treatment. The as-prepared products were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET) analysis, Barrett-Joyner-Halenda (BJH) measurement, and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). The photocatalytic degradation of rhodamine B (Rh B) under visible light irradiation indicated that the ZFO composites calcined at 500 °C has the best photocatalytic activity (the photocatalytic degradation efficiency can reach up to 95.7% within 60 min) and can maintain a stable photocatalytic degradation efficiency for at least three cycles. In addition, the photocatalytic activity of ZFO composites toward dye decomposition follows the order cationic Rh B > anionic methyl orange. Finally, using different scavengers, superoxide and hydroxyl radicals were identified as the primary active species during the degradation reaction of Rh B.     

Synthesis and characterization of ternary nanocomposites of TiO2/rGO/CdS as an efficient catalyst for photo-degradation of methyl orange

Novel ternary composite photocatalysts have been successfully prepared by TiO₂ nanofibers, reduced graphene oxide, and CdS nanoparticles (TiO₂/rGO/CdS) by using electrospinning technique with easy chemical methods. The structures and their properties are examined by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and field-emission scanning electron microscope (FESEM). The structural characterization of the composite reveals that pure TiO₂ NFs and CdS NPs crystalline very well and the reduced graphene oxide is tightly composed with TiO₂ NFs and CdS Nps. The photodegradation of methyl orange (MO) under UV light illumination is significantly enhanced compared with that of bare materials. This ternary composite degrades methyl orange within 75 min. The enhanced photocatalytic degradation performance resulted from effective separation of e–h pairs with rGO sheets and also contributed for high rate degradation efficiency. This novel ternary composite has a potential application of wastewater purification and utilization for energy conversions.     

Enhanced photocatalytic activity of bimodal mesoporous titania powders by C60 modification

In this work, fullerene modified TiO(2) nanocomposites (denoted as C(60)/TiO(2)) with low C(60) loadings (0-1.5 wt.%) have been prepared by a simple hydrothermal method using tetrabutylorthotitanate (TBOT, Ti(OC(4)H(9))(4)) as the titanium precursor. The as-prepared C(60)/TiO(2) nanocomposites were characterized by X-ray diffraction, transmission electron microscopy, UV-visible spectrophotometry, nitrogen adsorption, and X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy. The formation of hydroxyl radicals (˙OH) on the surface of UV-illuminated TiO(2) is probed by photoluminescence using terephthalic acid as a probe molecule. Our results have demonstrated that C(60) molecules can be dispersed as a monolayer onto bimodal mesoporous TiO(2)via covalent bonding. The photocatalytic oxidation rate of gas-phase acetone over C(60)/TiO(2) nanocomposites is greater than that over pure TiO(2), commercial Degussa P25 (P25) and C(60)-TiO(2) counterparts prepared by simple impregnating mixing. In particular, 0.5 wt.% C(60)/TiO(2) nanocomposites show the greatest photocatalytic activity with the rate constant k exceeding that of P25 by a factor of 3.3. Based on the results of the current study, we propose that C(60) molecules doped onto TiO(2) act as "electron acceptors" responsible for the efficient separation of photogenerated charge carriers and the enhancement of photocatalytic activity. The proposed mechanism for the observed photocatalytic performance of C(60)/TiO(2) nanocomposites is further corroborated by experiments on hydroxyl radical and transient photocurrent response.