Synthesis of ammonia from natural gas at atmospheric pressure with doped ceria–Ca<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>–K<Subscript>3</Subscript>PO<Subscript>4</Subscript> composite electrolyte and its proton conductivity at intermediate temperature

A new type of oxide–salt composite electrolyte, yttrium doped ceria YDC–Ca₃(PO₄)₂–K₃PO₄, was developed and demonstrated for its promising use for ammonia synthesis. Using this composite electrolyte, ammonia was synthesized from nitrogen and natural gas at atmospheric pressure in the solid-state proton conducting cell reactor, and the optimal condition for ammonia production was determined . The evolved rate of ammonia is up to 6.95×10⁻⁹ mol s⁻¹ cm⁻².     

Synthesis and characterization of macroporous Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C composites as cathode materials for Li-ion batteries

The macroporous Li₃V₂(PO₄)₃/C composite was synthesized by oxalic acid-assisted carbon thermal reaction, and the common Li₃V₂(PO₄)₃/C composite was also prepared for comparison. These samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and electrochemical performance tests. Based on XRD and SEM results, the sample has monoclinic structure and macroporous morphology when oxalic acid is introduced. Electrochemical tests show that the macroporous Li₃V₂(PO₄)₃/C sample has a high initial discharge capacity (130 mAh g⁻¹ at 0.1 C) and a reversible discharge capacity of 124.9 mAh g⁻¹ over 20 cycles. Moreover, the discharge capacity of the sample is still 91.5 mAh g⁻¹, even at a high rate of 2 C, which is better than that of the sample with common morphology. The improvement in electrochemical performance should be attributed to its improved lithium ion diffusion coefficient for the macroporous morphology, which was verfied by cyclic voltammetry and electrochemical impedance spectroscopy.     

Synthesis of electrospun BaSrTiO<Subscript>3</Subscript>/PVP nanofibers

Ba_1−x Sr _x TiO₃(x = 0–0.5, BST) nanofibers with diameters of 150–210 nm were prepared by using electrospun BST/polyvinylpyrrolidone (PVP) composite fibers by calcination for 2 h at temperatures in the range of 650–800 °C in air. The morphology and crystal structure of calcined BST/PVP nanofibers were characterized as functions of calcination temperature and Sr content with an aid of XRD, FT-IR, and TEM. Although several unknown XRD peaks were detected when the fibers were calcined at temperatures less than 750 °C, they disappeared with increasing the temperature (above 750 °C) due to its thermal decomposition and complete reaction in the formation of BST. In addition, the FT-IR studies of BST/PVP fibers revealed that the intensities of the O–H stretching vibration bands (at 3430 and 1425 cm⁻¹) became weaker with increasing the calcination temperature and a broad band at 540 cm⁻¹, Ti–O vibration, appeared sharper and narrower after calcination above 750 °C due to the formation of metal oxide bonds. However, no effect of Sr content on the crystal structure of the composites was detected.     

Preparation and characterization of ZrWMoO<Subscript>8</Subscript> powders with different morphologies

ZrWMoO₈ powders with different morphologies were obtained using ammonium tungstate, molybdate tungstate and zirconium tungstate as the starting materials by dehydrating the precursor ZrWMoO₇(OH)₂(H₂O)₂. The precursor was studied by thermo-gravimetric and differential scanning calorimetry (TG-DSC). The influence of the gelling agents (HCl, HClO₄, HNO₃, H₂SO₄ and H₃PO₄) on the crystallization process and crystal morphology of the products prepared was investigated by X-ray powder diffraction (XRD), scanning electron micrograph (SEM) and X-ray fluorescence spectrometer (XRF). Results showed that the morphology of the ZrWMoO₈ particles can be simply adjusted by changing the gelling agents, and the thermal expansion coefficients of cubic ZrWMoO₈ prepared in HCl solution are −3.84 × 10⁻⁶ K⁻¹ from 100°C to 700°C. __________ Translated from Chemical Journal of Chinese University, 2007, 28(3): 397–401 [译自: 高等学校化学学报]     

Nano-composites SnO(VO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>) as anodes for lithium ion batteries

Nano-composites of SnO(V₂O₃) _x (x = 0, 0.25, and 0.5) and SnO(VO)_0.5 are prepared from SnO and V₂O₃/VO by high-energy ball milling (HEB) and are characterized by X-ray diffraction (XRD), scanning electron microscopy, and high-resolution transmission electron microscopy techniques. Interestingly, SnO and SnO(VO)_0.5 are unstable to HEB and disproportionate to Sn and SnO₂, whereas HEB of SnO(V₂O₃) _x gives rise to SnO₂.VO _x . Galvanostatic cycling of the phases is carried out at 60 mA g⁻¹ (0.12 C) in the voltage range 0.005–0.8 V vs. Li. The nano-SnO(V₂O₃)_0.5 showed a first-charge capacity of 435 (±5) mAh g⁻¹ which stabilized to 380 (±5) mAh g⁻¹ with no noticeable fading in the range of 10–60 cycles. Under similar cycling conditions, nano-SnO (x = 0), nano-SnO(V₂O₃)_0.25, and nano-SnO(VO)_0.5 showed initial reversible capacities between 630 and 390 (±5) mAh g⁻¹. Between 10 and 50 cycles, nano-SnO showed a capacity fade as high as 59%, whereas the above two VO _x -containing composites showed capacity fade ranging from 10% to 28%. In all the nano-composites, the average discharge potential is 0.2–0.3 V and average charge potential is 0.5–0.6 V vs. Li, and the coulombic efficiency is 96–98% after 10 cycles. The observed galvanostatic cycling, cyclic voltammetry, and ex situ XRD data are interpreted in terms of the alloying–de-alloying reaction of Sn in the nano-composite “Sn-VO _x -Li₂O” with VO _x acting as an electronically conducting matrix.     

Nitrogen-doped TiO<Subscript>2</Subscript> nanopowders prepared by chemical vapor synthesis: band structure and photocatalytic activity under visible light

During chemical vapor synthesis of TiO₂ nanopowders, nitrogen atoms were doped into the crystal lattice of TiO₂. The nitrogen atoms were predominantly incorporated substitutionally in the crystal lattice of TiO₂ nanopowders up to the doping level of 1.25 mol% nitrogen, whereas they were in both interstitial and substitutional sites over about 1.43 mol% nitrogen. From the photocatalytic activity of nitrogen-doped TiO₂ estimated by decomposition of methylene blue under visible light, it was found that the substitutional nitrogen anions appearing at the low level doping was beneficial to its photocatalytic activity, whereas the interstitial ones appearing at the high level doping over 1.25 mol% nitrogen were not. The improved photocatalytic activity due to the substitutionally doped nitrogen was attributed to band gap narrowing which was confirmed by the studies of XPS, near edge X-ray absorption fine structure, and UV–Vis absorption.     

Synthesis and supercapacitance of flower-like Co(OH)<Subscript>2</Subscript> hierarchical superstructures self-assembled by mesoporous nanobelts

A facile hydrothermal strategy was first proposed to synthesize flower-like Co(OH)₂ hierarchical microspheres. Further physical characterizations revealed that the flower-like Co(OH)₂ microspherical superstructures were self-assembled by one-dimension nanobelts with rich mesopores. Electrochemical performance of the flower-like Co(OH)₂ hierarchical superstructures were investigated by cyclic voltammgoram, galvanostatic charge–discharge and electrochemical impedance spectroscopy in 3 M KOH aqueous electrolyte. Electrochemical data indicated that the flower-like Co(OH)₂ superstructures delivered a specific capacitance of 434 F g⁻¹ at 10 mA cm⁻² (about 1.33 A g⁻¹), and even kept it as high as 365 F g⁻¹ at about 5.33 A g⁻¹. Furthermore, the SC degradation of about 8% after 1,500 continuous charge–discharge cycles at 5.33 A g⁻¹ demonstrates their good electrochemical stability at large current densities.     

Preparation and electrochemical performance of Li3V2(PO4)3/C cathode material by spray-drying and carbothermal method

Composite Li₃V₂(PO₄)₃/C cathode material can be synthesized by spray-drying and carbothermal method. The monoclinic-phase Li₃V₂(PO₄)₃/C was prepared with the process of double spray drying at 260 °C and subsequent heat treatment at 750 °C for 12 h. The results indicate that the Li₃V₂(PO₄)₃/C presents large reversible discharge capacity of 121.9 mA h g⁻¹ and charge capacity of 131.8 mA h g⁻¹ at the current density of C/5, good rate capability with 61.1 mA h g⁻¹ at 20C, and excellent capacity retention rate close to 100% at various current densities in the region of 3.0–4.3 V.     

Effect of protonation and deprotonation on surface charge density of Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>

The protonation and deprotonation of the Nb₂O₅ surface has been followed in order to understand the reactions of surface of this catalyst. The simultaneous potentiometric and conductometric titrations had been carried by using 50 mL of water suspension of Nb₂O₅ 40 g L⁻¹. The oxide was entirely deprotonated when adding 0.4 mL NaOH 1 mol L⁻¹, and later titrated with 0.1 mol L⁻¹. The titration had supplied K ₁ and K ₂ and the obtained values were 3.24 × 10⁻³ and 4.17 × 10⁻⁸, respectively. The zero point charge was pH_pcz = 4.94. The thermodynamic studies were carried out by using 50 mL of a 40 g/L Nb₂O₅ aqueous suspension with the pH adjusted to pH_PZC value. The suspension was titrated with 0.5 mol/L of HNO₃ or NaOH for protonation or deprotonation studies, respectively, in an isoperibol calorimeter CSC ISC-4300. Thus, the obtained thermodynamic values of the protonation and deprotonation of Nb₂O₅ were Δ_dp G = −37.60 kJ/mol, Δ_dp H = −23.72 kJ/mol and Δ_dpS = 47 J/(mol K).     

Synthesis of Nanocrystalline TiO<Subscript>2</Subscript> Particles and Their Structural Characteristics

Controlled nanosized TiO₂ particles of 4–10 nm were synthesized by a simple hydrolysis method followed by calcination at different temperatures. These particles were investigated using X-ray diffraction (XRD), Photoacoustic/Fourier transform infrared (PA/FTIR) spectroscopy, Raman spectroscopy and electron spin resonance (ESR) spectroscopy to understand their structural properties. X-ray diffraction studies confirmed the anatase phase of the particles where as the PA/FTIR revealed the bands around 1,500 and 3,300 cm⁻¹ due to –OH bands. ESR spectroscopic investigations carried out from 5 to 300 K indicated the presence of an ESR line at g = 2.00 emerging from radical species. It is significant to note that the intensity of the ESR line decreased as the particle size increased.     

Electrochemical performance of LiVPO<Subscript>4</Subscript>F/C composite cathode prepared through amorphous vanadium phosphorus oxide intermediate

LiVPO₄F/C composites with better electrochemical performance were prepared by calcination of LiF and amorphous vanadium phosphorus oxide (VPO) intermediate synthesized by a sol–gel method using H₃PO₄, V₂O₅ and citric acid as raw materials. The properties of LiVPO₄F/C composites were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical tests. The analysis of XRD patterns and Fourier transform infrared spectra (FTIR) reveal that VPO intermediate prepared by sol–gel method is amorphous and VPO₄ may exist in VPO intermediate. The compositions of LiVPO₄F/C composites are related to the calcination temperature for preparation of amorphous VPO/C intermediate and LiVPO₄F/C composite prepared by VPO/C synthesized at 700°C consists of a single crystal phase of LiVPO₄F. The electrochemical tests show that LiVPO₄F/C composite prepared by VPO/C synthesized at 700°C exhibits higher discharge capacity and excellent cycle performance. This LiVPO₄F/C composite displays discharge capacity of 133 mAh g⁻¹ at 0.5 C (78 mA g⁻¹) and remains capacity retention of 96.8% after 30 cycles, even at a high rate of 5 C, the composite exhibits high discharge capacity of 115 mAh g⁻¹ and capacity retention of 97% after 100 cycles.     

Electrochemical performance of LiFePO<Subscript>4</Subscript>/C doped with F synthesized by carbothermal reduction method using NH<Subscript>4</Subscript>F as dopant

The effect of fluorine doping on the electrochemical performance of LiFePO₄/C cathode material is investigated. The stoichiometric proportion of LiFe(PO₄)_1−x F_3x /C (x = 0.01, 0.05, 0.1, 0.2) materials was synthesized by a solid-state carbothermal reduction route at 650 °C using NH₄F as dopant. X-ray diffraction, scanning electron microscope, energy-dispersive X-ray, and X-ray photoelectron spectroscopy analyses demonstrate that fluorine can be incorporated into LiFePO₄/C without altering the olivine structure, but slightly changing the lattice parameters and having little effect on the particle sizes. However, heavy fluorine doping can bring in impurities. Fluorine doping in LiFePO₄/C results in good reversible capacity and rate capability. LiFe(PO₄)_0.95 F_0.15/C exhibits highest initial capacity and best rate performance. Its discharge capacities at 0.1 and 5 C rates are 156.1 and 119.1 mAh g⁻¹, respectively. LiFe(PO₄)_0.95 F_0.15/C also presents an obviously better cycle life than the other samples. We attribute the improvement of the electrochemical performance to the smaller charge transfer resistance (R _ct) and influence of fluorine on the PO₄³⁻ polyanion in LiFePO₄/C.     

An EPR investigation of acetonitrile reactivity with superoxide radicals on polycrystalline TiO<Subscript>2</Subscript>

The interaction of acetonitrile with superoxide radicals over a polycrystalline TiO₂ (Degussa P25) surface was investigated using continuous-wave electron paramagnetic resonance (cw-EPR) spectroscopy. For the first time, a thermally unstable radical intermediate has been observed following the low-temperature exposure of acetonitrile to surface-adsorbed O₂⁻ radicals. The radical intermediate has been identified as an [O₂⁻···CH₃CN] type surface complex characterised by the g values of g ₁ = 2.031, g ₂ = 2.010 and g ₃ = 2.003. This surface complex is thermally unstable and decomposes at temperatures of T > 240 K. A second oxygen-centred species was also observed following acetonitrile adsorption, characterised by the spin Hamiltonian parameters of g ₁ = 2.028, g ₂ = 2.010, g ₃ = 2.004, A ₁ = 1.2 mT, A ₂ = 1.0 mT and A ₃ = 1.0 mT, and was assigned to a hydroperoxy radical (HO₂^•).     

Thermal expansion and heat capacity measurements on Ba10?xCsx(PO4)6Cl2?δ, (x?=?0, 0.5) chloroapatites synthesized by sonochemical process

Ba_10−x Cs _x (PO₄)₆Cl₂, (x = 0, 0.5) chloroapatite ceramics were prepared by sonochemical method of synthesis. The measured room temperature lattice parameters of Ba₁₀ (PO₄)₆Cl₂ and Ba_9.5Cs_0.5 (PO₄)₆Cl_2−δ are practically the same; that is, a = 10.26 (8), c = 7.65 (7) and a = 10.27 (7), c = 7.65 (5), respectively. Heat capacity measurements were carried out on these materials by differential scanning calorimetry (DSC) in the temperature range 298–800 K. The heat capacity values of Ba_9.5Cs_0.5(PO₄)₆Cl_2−δ are found to be slightly higher at all temperatures than those of Ba₁₀(PO₄)₆Cl₂. From the heat capacity data, other thermodynamic functions such as enthalpy and entropy increments were computed. The heat capacity values of Ba₁₀(PO₄)₆Cl₂ and Ba_9.5Cs_0.5(PO₄)₆Cl_2−δ at 298 K are 0.3912 and 0.4310 J K⁻¹ g⁻¹, respectively. Thermal expansion property of the doped and undoped barium chloroapatites was measured by using a home built dilatometer which uses LVDT as displacement sensor. The bulk thermal expansion of Ba₁₀(PO₄)Cl₂ and Ba_9.5Cs_0.5(PO₄)Cl_2−δ is observed to be about 0.9% in the temperature range of 298–973 K.     

Effect of heat treatment on electrochromic properties of TiO<Subscript>2</Subscript> thin films

Electrochromic titanium oxide (TiO₂) films were deposited on ITO/glass substrates by chemical solution deposition (CSD). The stock solutions were spin-coated onto substrates and then heated at various temperatures (200–500 °C) in various oxygen concentrations (0–80%) for 10 min. The effects of the processing parameters on the electrochromic properties of TiO₂ films were investigated. X-ray diffraction measurements demonstrated that the amorphous TiO₂ films were crystallized to form anatase films above 400 °C. The electrochromic properties and transmittance of TiO₂ films were measured in 1 M LiClO₄–propylene carbonate (PC) non-aqueous electrolyte. An amorphous 350 nm-thick TiO₂ film that was heated at 300°C in 60% ambient oxygen exhibited the maximum transmittance variation (ΔT%), 14.2%, between the bleached state and the colored state, with a ΔOD of 0.087, Q of 10.9 mC/cm², η of 7.98 cm²/C and x in Li _x ClO₄ of 0.076 at a wavelength (λ) of 550 nm.     

Comparison of different soft chemical routes synthesis of submicro-LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> and their influence on its electrochemical properties

A comparative study of submicro-crystalline spinel LiMn₂O₄ powders prepared by two different soft chemical routes such as hydrothermal and sol–gel methods is made. The dependence of the physicochemical properties of the spinel LiMn₂O₄ powder has been extensively investigated by using X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscope, cyclic voltammogram, charge–discharge test, and electrochemical impedance spectroscopy (EIS). The results show that the electrochemical performances of spinel LiMn₂O₄ depend strongly upon the synthesis method. The LiMn₂O₄ powder prepared by hydrothermal route has higher specific capacity and better cycling performance than the one synthesized from sol–gel method. The former has the max discharge capacity of 114.36 and 99.78 mAh g⁻¹ at the 100th cycle, while the latter has the max discharge capacity of 98.67 and 60.25 mAh g⁻¹ at the 100th cycle. The selected equivalent circuit can fit well the EIS results of synthesized LiMn₂O₄. For spinel LiMn₂O₄ from sol–gel method and hydrothermal route in the first charge process R _SEI remain almost invariable, R _e and R _ct first decreasing and then increasing with the increase of polarization potential.     

Multiconfigurational study on the synchronous mechanisms of the ClO self-reaction leading to Cl or Cl<Subscript>2</Subscript>

For studying the adiabatic and nonadiabatic mechanisms of the ClO (X ²Π) + ClO (X ²Π) → ClOOCl → 2Cl (² P _u) + O₂ (X ³Σ _g ⁻) reaction (1) and the ClO (X ²Π) + ClO (X ²Π) → ClOOCl → Cl₂ (X ¹Σ _g ⁺) + O₂ (X ³Σ _g ⁻) reaction (2), we calculated, by partial geometry optimizations under the C₂ constraint, the O–O and O–Cl dissociation potential energy curves (PECs) from the five low-lying states of ClOOCl at the CASPT2 level. The CASSCF minimum-energy crossing point (MECP) between the potential energy surfaces of the 1 ¹A ground state [correlating with the product of reaction (1)] and the 1 ³B state [correlating with the product of reaction (2)] states was also determined. Based on the CAS calculation results (PECs, energies, and spin–orbit coupling at the MECP), we predict that reaction (1) occurs along pathway 1: ClO (X ²Π) + ClO (X ²Π) → ClOOCl (1 ¹A) → 2Cl (² P _u) + O₂ (X ³Σ _g ⁻) and that reaction (2) occurs along pathway 2: ClO (X ²Π) + ClO (X ²Π) → ClOOCl (1 ¹A) → 1 ¹A/1 ³B MECP (142.4 cm⁻¹) → ClOOCl (1 ³B) → Cl₂ (X ¹Σ _g ⁺) + O₂ (X ³Σ _g ⁻). The needed energies (relative to the reactant) for pathways 1 and 2 are predicted to be 5.3 and 11.1 kcal/mol, respectively, which indicates that reaction (1) is more favorable than reaction (2). The present work supports the traditional photochemical model for ozone degradation: ClOOCl (1 ¹A), formed by two ClO (X ²Π), can directly produce O₂ plus two Cl atoms.     

N,B, Si-tridoped mesoporous TiO<Subscript>2</Subscript> with high surface area and excellent visible-light photocatalytic activity

N, B, Si-tridoped mesoporous TiO₂, together with N-doped, N, B-codoped and N, Si-codoped TiO₂, was prepared by a modified sol–gel method. The samples were characterized by wide-angle X-ray diffraction (WAXRD), N₂ adsorption–desorption, transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, UV–visible adsorbance spectra (UV–vis) and X-ray photoelectron spectra (XPS). The N, B, Si-tridoped mesoporous TiO₂ showed small crystallite size, large specific surface area (350 m²/g), uniform pore distribution (3.2 nm) and strong absorption in the visible light region. The photocatalytic activities of the samples were evaluated by the photodegradation of 2,4-dichlorophenol (2,4-DCP) aqueous solution. The N, B, Si-tridoping sample exhibited much higher photocatalytic activity compared with other synthesized photocatalysts. The high activity could be attributed to the strong absorption in the visible light region, large specific surface area, small crystallite size, large amount of surface hydroxyl groups, and mesoporosity.     

Hydrothermal synthesis of (Fe,N) co-doped TiO<Subscript>2</Subscript> powders and their photocatalytic properties under visible light irradiation

(Fe, N) co-doped titanium dioxide powders have been prepared by a quick, low-temperature hydrothermal method using TiOSO₄, CO(NH₂)₂, Fe(NO₃)₃, and CN₃H₅ · HCl as starting materials. The synthesized powders were characterized by XRD, TEM, BET, XPS, and UV–Vis spectroscopy. Experimental results show that the as-synthesized TiO₂ powders are present as the anatase phase and that the N and Fe ions have been doped into the TiO₂ lattice. The specific surface area of the powders is 167.8 m²/g by the BET method and the mean grain size is about 11 nm, calculated by Scherrer’s formula. UV–Vis absorption spectra show that the edge of the photon absorption has been red-shifted up to 605 nm. The doped titanium dioxide powders had excellent photocatalytic activity during the process of photo-degradation of formaldehyde and some TVOC gases under visible light irradiation.     

Crystallization and Phase Stability of CaSO<Subscript>4</Subscript> and CaSO<Subscript>4</Subscript> – Based Salts

Summary.  Calcium sulfate occurs in nature in form of three different minerals distinguished by the degree of hydration: gypsum (CaSO₄·2H₂O), hemihydrate (CaSO₄·0.5H₂O) and anhydrite (CaSO₄). On the one hand the conversion of these phases into each other takes place in nature and on the other hand it represents the basis of gypsum-based building materials. The present paper reviews available phase diagram and crystallization kinetics information on the formation of calcium sulfate phases, including CaSO₄-based double salts and solid solutions. Uncertainties in the solubility diagram CaSO₄–H₂O due to slow crystallization kinetics particularly of anhydrite cause uncertainties in the stable branch of crystallization. Despite several attempts to fix the transition temperatures of gypsum–anhydrite and gypsum–hemihydrate by especially designed experiments or thermodynamic data analysis, they still vary within a range from 42–60°C and 80–110°C. Electrolyte solutions decrease the transition temperatures in dependence on water activity. Dry or wet dehydration of gypsum yields hemihydrates (α-, β-) with different thermal and re-hydration behaviour, the reason of which is still unclear. However, crystal morphology has a strong influence. Gypsum forms solid solutions by incorporating the ions HPO₄ ²⁻, HAsO₄ ²⁻, SeO₄ ²⁻, CrO₄ ²⁻, as well as ion combinations Na⁺(H₂PO₄)⁻ and Ln³⁺(PO₄)³⁻. The channel structure of calcium sulfate hemihydrate allows for more flexible ion substitutions. Its ion substituted phases and certain double salts of calcium sulfate seem to play an important role as intermediates in the conversion kinetics of gypsum into anhydrite or other anhydrous double salts in aqueous solutions. The same is true for the opposite process of anhydrite hydration to gypsum. Knowledge about stability ranges (temperature, composition) of double salts with alkaline and alkaline earth sulfates (esp. Na₂SO₄, K₂SO₄, MgSO₄, SrSO₄) under anhydrous and aqueous conditions is still very incomplete, despite some progress made for the systems Na₂SO₄–CaSO₄ and K₂SO₄–CaSO₄–H₂O. Corresponding author. E-mail: daniela.freyer@chemie.tu-freiberg.de Received December 17, 2002; accepted January 10, 2003 Published online April 3, 2003