In-line application of electric field in capillary separation systems: Joule heating, pH and conductivity

This study concerns the technique electric field-assisted capillary liquid chromatography. In this technique, an electric field is applied over the separation capillary in order to provide an additional selectivity. In this technique, the electric field is applied in-line in the separation capillary and here the electric current is the factor limiting the magnitude of applied electric field. The influence of Joule heating and other factors on the current in such systems has been investigated. The temperature in the capillary was first measured within a standard CE set-up, as function of effect per unit of length. Then the same cooling system was applied to an in-line set-up, to replicate the conditions between the two systems, and thus the temperature. Thus Joule heating effects could then be calculated within the in-line system. It was found that for systems applying an electric field in line, the direct influence from Joule heating was only relatively small. The pH in the capillary was measured in the in-line set-up using cresol red/TRIS solutions as pH probe. Significant changes in pH were observed and the results suggested that electrolysis of water is the dominant electrode reaction in the in-line system. In summary, the observed conductivity change in in-line systems was found to be mainly due to the pH change by hydrolysis of water, but primarily not due the temperature change in the capillary column.     

Effect of Joule heating on efficiency and performance for microchip-based and capillary-based electrophoretic separation systems: a closer look

An attempt is made to revisit the main theoretical considerations concerning temperature effects ("Joule heating") in electro-driven separation systems, in particular lab-on-a-chip systems. Measurements of efficiencies in microfabricated devices under different Joule heating conditions are evaluated and compared to both theoretical models and measurements performed on conventional capillary systems. The widely accepted notion that planar microdevices are less susceptible to Joule heating effects is largely confirmed. The heat dissipation from a nonthermostatically controlled glass microdevice was found to be comparable to that from a liquid-cooled-fused silica capillary. Using typically dimensioned glass and glass/silicon microdevices, the experimental results indicate that 5-10 times higher electric field strengths can be applied than on conventional capillaries, before detrimental effects on the separation efficiency occur. The main influence of Joule heating on efficiency is via the establishment of a radial temperature profile across the lumen of the capillary or channel. An overall temperature increase of the buffer solution has only little influence on the quality of the separation. Still, active temperature control (cooling, thermostatting) can help prevent boiling of the buffer and increase the reproducibility of the results.     

Joule heating induced transient temperature field and its effects on electroosmosis in a microcapillary packed with microspheres

The Joule heating induced transient temperature field and its effect on the electroosmotic flow in a capillary packed with microspheres is analyzed numerically using the control-volume-based finite difference method. The model incorporates the coupled momentum equation for the electroosmotic velocity, the energy equations for the Joule heating induced temperature distributions in both the packed column and the capillary wall, and the mass and electric current continuity equations. The temperature-dependent physical properties of the electrolyte solution are taken into consideration. The characteristics of the Joule heating induced transient development of temperature and electroosmotic flow fields are studied. Specifically, the simulation shows that the presence of Joule heating causes a noticeable axial temperature gradient in the thermal entrance region and elevates a significant temperature increment inside the microcapillary. The temperature changes in turn greatly affect the electroosmotic velocity by means of the temperature-dependent fluid viscosity, dielectric constant, and local electric field strength. Furthermore, the model predicts an induced pressure gradient to counterbalance the axial variation of the electroosmotic velocity so as to maintain the fluid mass continuity. In addition, under specific conditions, the present model is validated by comparing with the existing analytical model and experimental data from the literature.     

Joule heating in packed capillaries used in capillary electrochromatography

Effective heat dissipation is critical for reproducible and efficient separations in electrically driven separation systems. Flow rate, retention kinetics, and analyte diffusion rates are some of the characteristics that are affected by variation in the temperature of the mobile phase inside the column. In this study, we examine the issue of Joule heating in packed capillary columns used in capillary electrochromatography (CEC). As almost all commonly used CEC packings are poor thermal conductors, it is assumed that the packing particles do not conduct heat and heat transfer is solely through the mobile phase flowing through the system. The electrical conductivity of various mobile phases was measured at different temperatures by a conductivity meter and the temperature coefficient for each mobile phase was calculated. This was followed by measurement of the electrical current at several applied voltages to calculate the conductivity of the solution within the column as a function of the applied voltage. An overall increase in the conductivity is attributed to Joule heating within the column, while a constant conductivity means good heat dissipation. A plot of conductivity versus applied voltage was used as the indicator of poor heat dissipation. Using theories that have been proposed earlier for modeling of Joule heating effects in capillary electrophoresis (CE), we estimated the temperature within CEC columns. Under mobile and stationary phase conditions typically used in CEC, heat dissipation was found to be not always efficient. Elevated temperatures within the columns in excess of 23 degrees C above ambient temperature were calculated for packed columns, and about 35 degrees C for an open column, under a given set of conditions. The results agree with recently published experimental findings with nuclear magnetic resonance (NMR) thermometry, and Raman spectroscopic measurements.     

Peak dispersion and contributions to plate height in nonaqueous capillary electrophoresis at high electric field strengths: ethanol as background electrolyte solvent

Nonaqueous capillary electrophoretic separations were performed under high electric field strengths (up to 2000 Vcm(-1)) in ethanolic background electrolyte solution and the contributions of different band broadening effects to plate height were evaluated. Under optimum conditions, increasing the field strength will provide faster separations and increased separation efficiency. Decrease in the separation efficiency at high field strengths was, however, observed in a previous study and now in the present paper an attempt is made to quantify various band broadening effects by applying a plate height model, which included the contributions of the injection plug length, diffusion, electromigration dispersion, Joule heating, analyte adsorption to the capillary wall, and detector slit aperture length. Of special interest were the contributions of Joule heating and analyte adsorption to the capillary wall. Poly(glycidylmethacrylate-co-N-vinylpyrrolidone)-coated fused-silica capillaries were used with internal diameters (ID) ranging from 30 to 75 microm. The separation efficiencies obtained experimentally were compared with the theoretically calculated efficiencies and fairly good agreement was observed for the 30 microm ID capillary. Relatively large deviation from the predictions of the model was found for the other capillary diameters especially at higher field strengths. The possible reasons for the deviation were discussed.     

功能化苯并咪唑类离子液体的合成及性质

合成了一系列由磺酸基、 羧基修饰的新型功能化苯并咪唑类离子液体, 采用IR, ¹H NMR, ¹³C NMR和ESI-MS对其结构进行了表征, 研究了化合物的热稳定性、 电导率以及室温下在各种溶剂中的溶解性等性质. 结果表明, 该类离子液体在 280 ℃以下基本没有失重, 热稳定性较好; 在水溶液浓度为1×10^-3 mol/L时, 随着温度的升高, 电导率几乎与温度呈正比增大; 能与大多数有机溶剂互溶, 溶解性随着溶剂极性的增加而增大.     

Influence of flow and diffusion on protein separation in a continuous flow electrophoresis cell: computation procedure

Continuous flow zone electrophoresis is an efficient method for the non-destructive separation of biological materials in a flowing film of buffer solution in which the constituents of a sample are separated according to their electrophoretic mobilities, under the influence of an electric field. This paper deals with modeling of flow structure of the buffer solution taking into account the effect of electroosmosis, Joule heating and thermal free convection and the forced convection of axial flow. Modeling of diffusion is examined in a second part. The modeling equations and the corresponding boundary conditions are solved by finite difference methods. The various parameters affecting the quality of the fractionation are analyzed.     

Analytical study of Joule heating effects on electrokinetic transportation in capillary electrophoresis

Electric fields are often used to transport fluids (by electroosmosis) and separate charged samples (by electrophoresis) in microfluidic devices. However, there exists inevitable Joule heating when electric currents are passing through electrolyte solutions. Joule heating not only increases the fluid temperature, but also produces temperature gradients in cross-stream and axial directions. These temperature effects make fluid properties non-uniform, and hence alter the applied electric potential field and the flow field. The mass species transport is also influenced. In this paper we develop an analytical model to study Joule heating effects on the transport of heat, electricity, momentum and mass species in capillary-based electrophoresis. Close-form formulae are derived for the temperature, applied electrical potential, velocity, and pressure fields at steady state, and the transient concentration field as well. Also available are the compact formulae for the electric current and the volume flow rate through the capillary. It is shown that, due to the thermal end effect, sharp temperature drops appear close to capillary ends, where sharp rises of electric field are required to meet the current continuity. In order to satisfy the mass continuity, pressure gradients have to be induced along the capillary. The resultant curved fluid velocity profile and the increase of molecular diffusion both contribute to the dispersion of samples. However, Joule heating effects enhance the sample transport velocity, reducing the analysis time in capillary electrophoretic separations.     

Band-broadening in capillary zone electrophoresis with axial temperature gradients

It is widely accepted that Joule heating effects yield radial temperature gradients in capillary zone electrophoresis (CZE). The resultant parabolic profile of electrophoretic velocity of analyte molecules is believed to increase the band-broadening via Taylor-Aris dispersion. This typically insignificant contribution, however, cannot explain the decrease in separation efficiency at high electric fields. We show that the additional band-broadening due to axial temperature gradients may provide the answer. These axial temperature variations result from the change of heat transfer condition along the capillary, which is often present in CZE with thermostating. In this case, the electric field becomes nonuniform due to the temperature dependence of fluid conductivity, and hence the induced pressure gradient is brought about to meet the mass continuity. This modification of the electroosmotic flow pattern can cause significant band-broadening. An analytical model is developed to predict the band-broadening in CZE with axial temperature gradients in terms of the theoretical plate height. We find that the resultant thermal plate height can be very high and even comparable to that due to molecular diffusion. This thermal plate height is much higher than that due to radial temperature gradients alone. The analytical model explains successfully the phenomena observed in previous experiments.     

Convection in continuous-flow electrophoresis

The various types of convection possible in an electrophoresis device are indicated and criteria are presented from which estimates can be made of the importance of convection in the separation. These criteria also indicate design options possible to suppress or reduce convection effects.Specific consideration is then given to the convection induced by Joule heating in a representative continuous-flow electrophoresis configuration. Detailed solutions for the associated velocity and temperature distributions are presented and it is shown how they are influenced by the buffer through-put, wall cooling, and electric field intensity.Significant distinction is pointed out between counter- and co-flow operation. With the latter mode it would appear that larger gap devices could be successfully run in a normal gravitational environment.     

Internal electrolyte temperatures for polymer and fused-silica capillaries used in capillary electrophoresis

Polymers are important as materials for manufacturing microfluidic devices for electrodriven separations, in which Joule heating is an unavoidable phenomenon. Heating effects were investigated in polymer capillaries using a CE setup. This study is the first step toward the longer-term objective of the study of heating effects occurring in polymeric microfluidic devices. The thermal conductivity of polymers is much smaller than that of fused silica (FS), resulting in less efficient dissipation of heat in polymeric capillaries. This study used conductance measurements as a temperature probe to determine the mean electrolyte temperatures in CE capillaries of different materials. Values for mean electrolyte temperatures in capillaries made of New Generation FluoroPolymer (NGFP), poly-(methylmethacrylate) (PMMA), and poly(ether ether ketone) (PEEK) capillaries were compared with those obtained for FS capillaries. Extrapolation of plots of conductance versus power per unit length (P/L) to zero power was used to obtain conductance values free of Joule heating effects. The ratio of the measured conductance values at different power levels to the conductance at zero power was used to determine the mean temperature of the electrolyte. For each type of capillary material, it was found that the average increase in the mean temperature of the electrolyte (DeltaT(Mean)) was directly proportional to P/L and inversely proportional to the thermal conductivity (lambda) of the capillary material. At 7.5 W/m, values for DeltaT(Mean) for NGFP, PMMA, and PEEK were determined to be 36.6, 33.8, and 30.7 degrees C, respectively. Under identical conditions, DeltaT(Mean) for FS capillaries was 20.4 degrees C.     

Numerical analysis of the thermal effect on electroosmotic flow and electrokinetic mass transport in microchannels

Joule heating is present in electrokinetically driven flow and mass transport in microfluidic systems. Nowadays, there is a trend of replacing costly glass-based microfluidic systems by the disposable, cheap polymer-based microfluidic systems. Due to poor thermal conductivity of polymer materials, the thermal management of the polymer-based microfluidic systems may become a problem. In this study, numerical analysis is presented for transient temperature development due to Joule heating and its effect on the electroosmotic flow (EOF) and mass species transport in microchannels. The proposed model includes the coupling Poisson-Boltzmann (P-B) equation, the modified Navier-Stokes (N-S) equations, the conjugate energy equation, and the mass species transport equation. The results show that the time development for both the electroosmotic flow field and the Joule heating induced temperature field are less than 1 s. The Joule heating induced temperature field is strongly dependent on channel size, electrolyte concentration, and applied electric field strength. The simulations reveal that the presence of the Joule heating can result in significantly different characteristics of the electroosmotic flow and electrokinetic mass transport in microchannels.     

Extraction of organic compounds with room temperature ionic liquids

Room temperature ionic liquids are novel solvents with a rather specific blend of physical and solution properties that makes them of interest for applications in separation science. They are good solvents for a wide range of compounds in which they behave as polar solvents. Their physical properties of note that distinguish them from conventional organic solvents are a negligible vapor pressure, high thermal stability, and relatively high viscosity. They can form biphasic systems with water or low polarity organic solvents and gases suitable for use in liquid–liquid and gas–liquid partition systems. An analysis of partition coefficients for varied compounds in these systems allows characterization of solvent selectivity using the solvation parameter model, which together with spectroscopic studies of solvent effects on probe substances, results in a detailed picture of solvent behavior. These studies indicate that the solution properties of ionic liquids are similar to those of polar organic solvents. Practical applications of ionic liquids in sample preparation include extractive distillation, aqueous biphasic systems, liquid–liquid extraction, liquid-phase microextraction, supported liquid membrane extraction, matrix solvents for headspace analysis, and micellar extraction. The specific advantages and limitations of ionic liquids in these studies is discussed with a view to defining future uses and the need not to neglect the identification of new room temperature ionic liquids with physical and solution properties tailored to the needs of specific sample preparation techniques. The defining feature of the special nature of ionic liquids is not their solution or physical properties viewed separately but their unique combinations when taken together compared with traditional organic solvents.     

Rapid analysis of trace organics in aqueous solutions by enrichment in uncoated capillary columns

Summary A novel technique has been developed for the analysis of trace organics in aqueous solutions. Concentration of organics is effected by passage of the solution being analysed through uncoated plastic or metal capillaries as reported. The concentrated organics are then desorbed from the capillary using an organic solvent, and the desorbed solution is subsequently analysed by gas chromatography. Organics trapped inside a variety of columns have been recovered by solvent desorption in this manner using a number of different solvents, mixed solvents, different solvent volumes, different solvent flow rates through the capillary column and at different desorption temperatures, and the effects of these variables on the efficiency of desorption are discussed.     

Dual effect of high electric field in capillary electrophoresis study of the conformational stability of Bungarus fasciatus acetylcholinesterase

The effect of high electric field in capillary zone electrophoresis (CZE) was evaluated for the study of the thermally induced unfolding of Bungarus fasciatus acetylcholinesterase. This monomer enzyme is characterised by two interdependent uncommon structural features, the asymmetrical distribution of charged residues and a relatively low thermal denaturation temperature. Both traits were presumed to interfere in the thermal unfolding of this enzyme as investigated by CZE. This paper analyses the effect of high electric field on the behaviour of the enzyme native state. It is shown that increasing the applied field causes denaturation-like transition of the enzyme at a current power which does not induce excessive Joule heating in the capillary. The susceptibility to electric field of proteins like cholinesterases, with charge distribution anisotropy, large permanent dipole moment and notable molecular flexibility associated with moderate thermal stability, was subsequently discussed.     

Dual effect of high electric field in capillary electrophoresis study of the conformational stability of Bungarus fasciatus acetylcholinesterase

The effect of high electric field in capillary zone electrophoresis (CZE) was evaluated for the study of the thermally induced unfolding of Bungarus fasciatus acetylcholinesterase. This monomer enzyme is characterised by two interdependent uncommon structural features, the asymmetrical distribution of charged residues and a relatively low thermal denaturation temperature. Both traits were presumed to interfere in the thermal unfolding of this enzyme as investigated by CZE. This paper analyses the effect of high electric field on the behaviour of the enzyme native state. It is shown that increasing the applied field causes denaturation-like transition of the enzyme at a current power which does not induce excessive Joule heating in the capillary. The susceptibility to electric field of proteins like cholinesterases, with charge distribution anisotropy, large permanent dipole moment and notable molecular flexibility associated with moderate thermal stability, was subsequently discussed.     

Investigation of nanocomposite PNIPAm-g-graphene with pre-lower critical solution temperature rapid thermal response function for chip adaptive cooling: A molecular dynamics and computational fluid dynamics simulations

Temperature-sensitive hydrogels have been widely used for rapid adaptive cooling in electronic device thermal management with promising applications. However, existing temperature-sensitive hydrogels can only regulate the flow in the chip cooling system after the ambient temperature reaches their lower critical solution temperature (LCST). Before reaching LCST, effective rapid heat dissipation for electronic chips is not achievable. This study aims to develop a temperature-sensitive hydrogel that can provide assisted adaptive cooling for electronic chips before reaching its LCST. This requires the hydrogel to have a thermal conductivity far surpassing existing hydrogel materials. Using the temperature-sensitive hydrogel PNIPAm and graphene molecules as base materials, this research utilized molecular dynamics simulations to graft graphene molecules onto PNIPAm molecules in different ways, resulting in the temperature-sensitive hydrogel material PNIPAm-g-graphene. Non-equilibrium molecular dynamics (NEMD) was employed to calculate the thermal conductivity of this material under different temperature conditions. The results indicate that the thermal conductivity of PNIPAm-g-graphene can reach up to 1.95474 W/m K (graphene grafted at  CH₃ functional group, temperature at 280 K). Compared to the thermal conductivity of PNIPAm under the same conditions (0.45 W/m K), the increase in thermal conductivity is significant, demonstrating excellent thermal conductivity compared to PNIPAm. Subsequently, this study analyzed the underlying mechanisms of different thermal conductivities in materials obtained by grafting graphene molecules at different points using the method of overlap in Phonon Density of States Curves (PDOS) from the perspective of interfacial thermal conduction. Finally, through computational fluid dynamics (CFD) simulations, this study investigates the chip's adaptive cooling performance with PNIPAm-g-graphene material. The results show that, compared to traditional temperature-sensitive hydrogels, PNIPAm-g-graphene can achieve efficient adaptive cooling of chip hotspots before the cooling fluid temperature reaches its LCST value. This finding is significant for the field of chip cooling. The study proposes a new method for rapid, adaptive cooling of chip hotspots and explores its feasibility from the perspectives of molecular dynamics and CFD simulation. It holds importance in the thermal management of electronic devices and the rapid adaptive cooling of electronic chips.     

A simple method for assessment and minimization of errors in determination of electrophoretic or electroosmotic mobilities and velocities associated with the axial electric field distortion

It is commonly accepted that the modern CE instruments equipped with efficient cooling system enable accurate determination of electrophoretic or electroosmotic mobilities. It is also often assumed that velocity of migration in a given buffer is constant throughout the capillary length. It is simultaneously neglected that the noncooled parts of capillary produce extensive Joule heating leading to an axial electric field distortion, which contributes to a difference between the effective and nominal electric field potentials and between velocities in the cooled and noncooled parts of capillary. This simplification introduces systematic errors, which so far were however not investigated experimentally. There was also no method proposed for their elimination. We show a simple and fast method allowing for estimation and elimination of these errors that is based on combination of a long‐end and short‐end injections. We use it to study the effects caused by variation of temperature, electric field, capillary length, and pH.     

Effects of Tube Materials on Capillary Chromatography Based on Tube Radial Distribution of Ternary Mixture Carrier Solvents under Laminar Flow Conditions

A capillary chromatography system was developed using an open capillary tube and a ternary solvents carrier solution of water-hydrophilic/hydrophobic organic solvent mixture. The chromatography is called a tube radial distribution chromatography (TRDC) system. The TRDC system works without applying high voltages or using specific columns, such as monolithic and packed columns. In this study, the effects of tube materials on separation performance were examined in the TRDC system, by using poly(tetrafluoroethylene) (PTFE; 100–400?μm inner diameter), polyethylene (PE; 200?μm inner diameter), and copolymer of (tetrafluoroethylene–perfluoroalcoxyethylene) (PTFE–PFAE; 100?μm inner diameter) capillary tubes. An analyte solution of 2,6-naphthalenedisulfonic acid and 1-naphthol as a model was subjected to the system with a water–acetonitrile–ethyl acetate carrier solution; 15:3:2 volume ratio (water-rich carrier) and 3:8:4 volume ratio (organic solvent-rich carrier). The flow rates were adjusted to be 0.5?μL?min^?1 for PTFE and PTFE–PFAE tubes as well as 2.0?μL?min^?1 for PE tube under laminar flow conditions. These analytes in the solution were separated in this order with the water-rich carrier solution with baseline separation in the three capillary tubes, while they were eluted in the reverse order or not separated with the organic solvent-rich carrier solution. The effects of tube temperature on separation were also examined with the water-rich carrier solution; the best resolutions were observed at 0?°C of the tube temperature. The obtained results were compared with those of fused-silica capillary tube and discussed.     

Specific features of the formation of zinc and cadmium complexes with tetraphenylporphine in amphiprotic media

The kinetics of the complex formation reactions of tetraphenylporphine with zinc and cadmium acetates in mixed solvents containing alcohols and inert diluents was studied by electronic absorption spectroscopy. The dependences of the rate constant on the binary solvent composition have an extreme character, which is universal in the temperature range 298–313 K for different salts, alcohols, and weakly solvating diluents. The electric conductivity of zinc acetate solutions was measured in a wide range of compositions of alcohol-chloroform binary solvents. The electric conductivity increased with an increase in the content of alcohols.