Preparation and characterization of poly(acrylic acid)-based nanoparticles

The present investigation describes the synthesis and characterization of nanoparticles based on poly(acrylic acid) (PAA) intramolecularly cross-linked with diamine, 2,2′-(ethylenedioxy)bis(ethylamine), using water-soluble carbodiimide. The aqueous colloid dispersions of nanoparticles were clear or mildly opalescent depending on the ratio of cross-linking, pH of the solution, and the molecular weight of PAA, finding consistent with values of transmittance between 3% and 99%. The structure was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by dynamic light scattering (DLS) and transmission electron microscopy (TEM) measurements. It was found that particle size depends on the pH, and at a given pH, it was caused by the ratio of cross-linking and the molecular weight of PAA. Particle size measured by TEM varied in the range of 20 and 80 nm. In the swollen state, the average size of the particles measured by DLS was in the range of 35–160 nm.     

Thermally Conductive Study of Polyethylene/Al2O3 Composite Networks Cross-linked by Electron Beam Irradiation

The surface-modified Al₂O₃ particles were introduced into polyethylene(PE) to enhance the thermal conductivity, and PE/Al₂O₃ cross-linked networks with improved thermal and mechanical properties were prepared through electron beam(EB) irradiation technology. The incorporation of reactive irradiation sensitizer was useful in fabricating a high degree of cross-linking(DC) PE networks under a low irradiation dose. In the PE sample containing 2% sensitizer, DC ca.67.1% could be obtained under 60 kGy(1 kGy=1000 J/kg). EB-irradiation greatly improved the tensile stress of PE-based samples, and the tensile stresses of the samples with 0.2%-5% TMPTA(trimethylolpro-pane triacrylate) under 60 kGy were 24.61-27.77 MPa. All the EB-irradiated samples had higher Vicat softening temperatures than the samples without irradiation. After treatment at 120 kGy, the Vicat softening temperatures of PE-Al₂O₃-44/TMPTA-2 increased from 127℃ to 130.4℃. SEM images revealed that PE-Al₂O₃-50 samples with increased amount of Al₂O₃ particles showed a conduction "pathway," and thermal conductivity reached 0.67 W/(m·K). Thus, high-performance pipes were extruded, which could satisfy the static hydraulic blasting test and exhibit improved thermal conduction capability.     

Stabilization of superparamagnetic iron oxide nanoclusters in concentrated brine with cross-linked polymer shells

Iron oxide nanoparticles, in the form of sub-100-nm clusters, were synthesized in the presence of poly(acrylic acid) (PAA) or poly(styrene sulfonate-alt-maleic acid) (PSS-alt-MA) to provide electrosteric stabilization. The superparamagnetic nanoclusters were characterized using a superconducting quantum interference device (SQUID), transmission electron microscopy (TEM), dynamic light scattering (DLS), thermogravimetric analysis (TGA), and zeta potential measurements. To anchor the polymer shell on the nanoparticle surface, the polymer was cross-linked for a range of cross-linking densities. For nanoclusters with only 12% (w/w) PSS-alt-MA, electrosteric stabilization was sufficient even in 8 wt % NaCl. For PAA, the cross-linked polymer shell was essentially permanent and did not desorb even upon dilution of the nanoparticles for iron oxide concentrations down to 0.014 wt %. Without cross-linking, over half of the polymer desorbed from the particle surfaces. This general approach of the adsorption of polymer stabilizers onto nanoparticles followed by cross-linking may be utilized for a wide variety of cross-linkable polymers without the need to form covalent bonds between the nanoparticles and polymer stabilizer. Thus, this cross-linking approach is an efficient and inexpensive method of stabilizing nanoparticles for large-scale applications, including the electromagnetic imaging of subsurface reservoirs, even at high salinity.     

Robust and recoverable dual cross-linking networks in pressure-sensitive adhesives

Pressure-sensitive adhesives (PSAs) demand the ability to simultaneously improve toughness and adhesion. However, these requirements of PSAs have remained a great challenge because robust and recoverable characteristics are usually contradictory properties of PSAs. Dual cross-linking networks developed by incorporating dynamic noncovalent bonds into chemical cross-linking networks have the potential to mitigate these requirements in a wide variety of applications including adhesives, hydrogels, and elastomers. Herein, a facile approach to achieve dual cross-linking networks of acrylic PSAs with excellent mechanical properties and high-adhesive performance that integrate physically cross-linked networks into chemically cross-linked networks is proposed. Diurethane acrylic monomer-pentaerythritol ethoxylate (DAM-PEEL) groups were introduced into the acrylic PSA system through photopolymerization. The PSA/DAM-PEEL dual cross-linking networks led to the development of the chemically cross-linked networks for both PSA and DAM via covalent bonds and the physically cross-linked networks between the amide groups of DAM and the hydroxyl groups of PEEL via hydrogen bonds. Consequently, the PSA/DAM-PEEL dual cross-linking networks were able to simultaneously improve the modulus and stretchability. This design strategy for developing dual cross-linking networks of materials could offer potential applications for various adhesive-related applications.     

A comparative study of the characteristics of cross-linked, oxidized and dual-modified rice starches

Rice starch was cross-linked with epichlorohydrin (0.3%, w/w, on a dry starch basis) and oxidized with sodium hypochlorite (2.5% w/w), respectively. Two dual-modified rice starch samples (oxidized cross-linked rice starch and cross-linked oxidized rice starch) were obtained by the oxidation of cross-linked rice starch and the cross-linking of oxidized rice starch at the same level of reagents. The physicochemical properties of native rice starch, cross-linked rice starch and oxidized rice starch were also studied parallel with those of the two dual-modified rice starch samples using rapid visco analysis (RVA), differential scanning calorimetry (DSC), dynamic rheometry and scanning electron microscopy (SEM). It was found that the levels of cross-linking and oxidation used in this study did not cause any significant changes in the morphology of rice starch granules. Cross-linked oxidized starch showed lower swelling power (SP) and solubility, and higher paste clarity in comparison with native starch. Cross-linked oxidized rice starch also had the lowest tendency of retrogradation and highest ability to resistant to shear compared with native, cross-linked, oxidized and oxidized cross-linked rice starches. These results suggest that the undesirable properties in native, cross-linked and oxidized rice starch samples could be overcome through dual-modification.     

Evaluation of the degree of cross-linking of cellulose-based superabsorbent hydrogels: a comparison between different techniques

Three different techniques have been applied to the evaluation of the degree of cross-linking of superabsorbent cellulose-based hydrogels obtained from water solutions of carboxymethylcellulose sodium salt (CMCNa) and hydroxyethylcellulose (HEC), chemically cross-linked with divinyl sulfone. These polyelectrolyte hydrogels are biodegradable and have the same sorption capacity as acrylate-based superabsorbents on the market. A ¹³C solid state NMR analysis was carried out on dry samples of hydrogel to obtain the degree of cross-linking, an important parameter that affects the swelling and mechanical properties of a hydrogel. Dynamic mechanical analysis was performed during the hydrogel cross-linking using a parallel plate rheometer under oscillatory deformations in order to monitor the evolution of the hydrogel viscoelastic properties during the synthesis. The value of |G*| and the slope of the stress-deformation ratio plots from uniaxial compression tests were used to evaluate the elastically effective degree of cross-linking according to classical rubber elasticity theory. Moreover, a dynamic mechanical analysis was carried out on cross-linked hydrogels at different degrees of swelling in order to investigate the influence of the swelling on the mechanical properties and the application of rubber elasticity theory to swollen hydrogels.     

Analytical characterisation of glutardialdehyde cross-linking products in gelatine-gum arabic complex coacervates

Encapsulates having shells of cross-linked mixtures of proteins and polysaccharides are widely used in the food and pharmaceutical industry for controlled release of actives and flavour compounds. In order to be able to predict the behaviour and the release characteristics of the microcapsules, a better understanding of the nature and extent of the cross-linking reaction is needed. Several analytical techniques were applied for the characterisation of glutardialdehyde (GDA) cross-linked encapsulates made of gelatine and gum arabic. To allow the use of sensitive, high-resolution methods such as chromatography and mass spectrometry, the sample first had to be hydrolysed. In this way, a mixture of amino acids, small peptides and the cross-link moieties was obtained. High-resolution liquid chromatography coupled to high-resolution mass spectrometry (HPLC-MS) was applied to detect possible cross-link markers through a comparison of HPLC-MS mass-chromatograms obtained for cross-linked and non-cross-linked coacervates. HPLC-MS/MS was used to identify the species responsible for the differences. Cross-linking occurred between GDA molecules and lysine and hydroxylysine epsilon-amino groups, and up to eight cross-link products of different nature could be identified. They included pyridinium ions and Schiff bases, and also unreacted GDA condensation products. Next, based on the insight gained in the possible chemical structures present in the cross-link markers, methods for selective labelling of these functionalities were employed to allow easier detection of related reaction products. Both liquid chromatography (LC) and gas chromatography (GC) were used in these experiments. Unfortunately, these approaches failed to detect new cross-link markers, most likely as a result of the low levels at which these are present.     

Effect of synthesis conditions of polyallylamine-beads-glucose (PAA-Glu) on boron adsorption

In this study, we assessed the boron adsorption characteristic of our synthesized adsorbent: polyallylamine-beads-glucose (PAA-Glu) by using the adsorption amount and adsorption site availability (ASA), and determined the optimum conditions for PAA-Glu synthesis. ASA is our proposed indicator and it expresses the percentage of the experimental equilibrium adsorption in relation to the theoretical equilibrium adsorption and indicates the availability of adsorption sites (hydroxyl groups) on adsorbents. We investigated the effects of the degree of cross-linking (20, 40 and 60 %), the introduction amount of α-D-glucose (40, 60 and 80 %), and the introduction temperature (30–150 °C) as regards PAA-Glu on the boron adsorption amount. The boron adsorption amount for PAA-Glu (20 % cross-linked, 30 °C) was superior to that for another degree of cross-linked PAA-Glu. However, the ASA for PAA-Glu (60 % cross-linked, 30 °C) exhibited the best value in this synthesized PAA-Glu. Furthermore, we examined the introduction temperature at which glucose was introduced to PAA-Glu (20 % cross-linked) in the 30–150 °C range, and we confirmed that the optimum temperature range for the synthesis of PAA-Glu was 60–80 °C. We found that controlling the space between the main chains of the polymer by using a spacer such as a cross-linker allowed boron molecules to come and go and led to an improvement in the boron adsorption amount and ASA.     

Structure and protein binding capacity of a planar PAA brush

We performed neutron reflectometry (NR) and total internal reflection fluorescence (TIRF) spectroscopy to characterize the structure and the protein binding capacity of a planar poly(acrylic acid) (PAA) brush at different temperatures. A PAA brush was prepared by spin-coating planar quartz or silicon wafers with a thin film of poly(styrene). Then, the diblock copolymer poly(styrene)-poly(acrylic acid) was deposited on these modified wafers using the Langmuir-Sch?fer or Langmuir-Blodgett technique. PAA grafting densities of about 0.1 chains per nm2 were obtained. The NR experiments indicate a remarkable swelling of the PAA brush in contact with a buffer solution, when it is heated to 40 degrees C for several hours. The swollen brush structure remains upon cooling back to 20 degrees C suggesting a disentanglement of the initially formed PAA brush by the temporary heating. At pD = 6.7, the protein bovine serum albumin (BSA) with a negative net charge is strongly adsorbed to the swollen PAA brush. From the scattering length density profiles obtained from the NR curves, an almost homogeneous filling of the whole PAA brush space with BSA molecules can be deduced corresponding to an average BSA volume fraction of about 7-10% and an adsorbed protein mass of about 1.4 mg m-2. By analyzing the TIRF experiments, it is found that BSA adsorption is enhanced when increasing the temperature which represents an evidence for an entropic driving force for protein adsorption. However, the mechanism of BSA adsorption at a PAA brush appears to be different at 20 and 40 degrees C.     

Structure–property relationships of anionic poly(urethane–urea) dispersion cross-linked with partially methylated melamine formaldehyde

An anionic poly(urethane–urea) dispersion (PUD) was cross-linked with different amount of partially methylated melamine formaldehyde (PMMF). The isothermal curing behavior was observed by a rigid-body pendulum rheometer. The test results showed that cure response of PUD cross-linked with PMMF was a function of the concentration of PMMF. Also, PMMF self-condensation could take place during the curing process. In this experiment, the anionic poly(urethane–urea) dispersion has a large number of >N–H cross-linking or branching sites in urethane and urea groups per molecule that allow a large number of PMMF to couple into elastic PUD backbone to form branched structure with partial cross-linking. The dynamic mechanical properties of PUD cross-linked with PMMF were affected by the concentration of PMMF. It was further shown that the tensile properties were strongly influenced by the concentration of PMMF and curing temperature.     

Elasticity of model poly(oxypropylene) networks

The equilibrium stress-strain properties and the swelling behavior of moderately cross-linked model networks of poly(oxypropylene) were studied. Results were in general agreement with the theory of rubber elasticity due to Flory. However, data on the highly cross-linked networks (M?_c ≈ 725) could not be satisfactorily described by the recent theories of elasticity or swelling. This is believed to be primarily due to the marked non-Gaussian character of the very short network chains and the substantial chemical modification of the polymer by the cross-linking moiety which inevitably occurs at high cross-link densities.     

Direct capture of product from fermentation broth using a cell-repelling ion exchanger

A new technique for treating anion exchangers has been proposed allowing direct capture of the fermentation product, shikimic acid directly from the cell-containing fermentation broth. A layer of hydrophilic polymer, poly(acrylic acid) (PAA) has been physically adsorbed on the anion exchanger followed by a covalent cross-linking of PAA. The PAA layer is penetrable for small molecules despite being negatively charged as PAA is, but the polymer layer repels large negatively charged structures like cell debris and cells preventing them from adsorption to the chromatographic matrix. The binding capacity for pure shikimic was about 81 mg/ml adsorbent for both cross-linked PAA-Amberlite and native Amberlite in the fluidized mode of column operation. Binding capacity dropped to 17 and 15 mg per ml adsorbent, respectively, when using filtrated fermentation broth and to about 10 mg/ml adsorbent for cross-linked PAA-Amberlite when using directly the fermentation broth containing cells. Native Amberlite cannot be used for the direct capture of shikimic acid due to the immediate clogging of the column and the collapse of the expanded bed. The cross-linked PAA-Amberlite was used repeatedly for the direct adsorption of shikimic acid from the industrial fermentation broth.     

基于聚(2-甲基-2-噁唑啉)和聚丙烯酸的混合刷在毛细管电泳在线富集溶菌酶中的应用

制备了一种对溶菌酶具有可控吸附性能的混合刷涂层毛细管,用于毛细管电泳在线富集溶菌酶以提高其检测灵敏度。首先,分别通过阳离子开环聚合和可逆加成-断裂链转移（RAFT）聚合合成聚（2-甲基-2-噁唑啉）（PMOXA）和聚丙烯酸（PAA）,然后将甲基丙烯酸缩水甘油酯（GMA）分别与PMOXA和PAA通过自由基共聚和RAFT聚合合成出聚（2-甲基-2-噁唑啉）-r-甲基丙烯酸缩水甘油酯（PMOXA-r-GMA）和聚丙烯酸-b-聚甲基丙烯酸缩水甘油酯（PAA-b-PGMA）。将PMOXA-r-GMA和PAA-b-PGMA的混合溶液以一定比例加入到毛细管内,通过加热即可制备出基于PMOXA和PAA的混合刷涂层毛细管。X射线光电子能谱（XPS）对毛细管原材料的表面组成研究结果表明,当混合溶液质量浓度为20 g/L、PMOXA-r-GMA和PAA-b-PGMA质量比为1：1时,所得涂层中羧基的含量随着PAA链长的增加而增加;异硫氰酸荧光素标记溶菌酶（FITC-溶菌酶）吸附实验结果显示,通过改变环境的pH和离子强度（I）可以调控涂层毛细管对溶菌酶的吸附和释放,在pH 7（I=10^-5mol/L）条件下,毛细管可以吸附大量的溶菌酶,当条件变为pH 3（I=10^-1mol/L）时,吸附的溶菌酶可以被释放出来。将这种具有溶菌酶可控吸附性能的涂层毛细管用于毛细管电泳在线富集溶菌酶,当PAA链长是PMOXA链长的2.2倍时,溶菌酶的灵敏度增强因子为17.69,检出限为8.7×10^-5g/L;同一天内对溶菌酶连续测定5次以及连续测定5天,峰面积的日内、日间相对标准偏差（RSD）分别为2.9%和4.1%,迁移时间的日内、日间RSD分别为0.9%和2.1%。涂层的制备只需一步,简单易行,而且涂层具有很好的稳定性。本研究为毛细管电泳分析痕量蛋白质提供了一种简单有效的方法。     

Novel poly(amido-amine)-based hydrogels as scaffolds for tissue engineering

Biodegradable and biocompatible amphoteric poly(amido-amine) (PAA)-based hydrogels, containing carboxyl groups along with amino groups in their repeating unit, were considered as scaffolds for tissue engineering applications. These hydrogels were obtained by co-polymerising 2,2-bisacrylamidoacetic acid with 2-methylpiperazine with or without the addition of different mono-acrylamides as modifiers, and in the presence of primary bis-amines as crosslinking agents. Hybrid PAA/albumin hydrogels were also prepared. The polymerisation reaction was a Michael-type polyaddition carried out in aqueous media. The PAA hydrogels were soft and swellable materials. Cytotoxicity tests were carried out by the direct contact method with fibroblast cell lines on the hydrogels both in their native state (that is, as free bases) and as salts with acids of different strength, namely hydrochloric, sulfuric, acetic and lactic acid. This was done in order to ascertain whether counterion-specific differences in cytotoxicity existed. It was found that all the amphoteric PAA hydrogels considered were cytobiocompatible both as free bases and salts. Selected hydrogels samples underwent degradation tests under controlled conditions simulating biological environments, i.e. Dulbecco medium at pH 7.4 and 37 degrees C. All samples degraded completely and dissolved within 10 d, with the exception of hybrid PAA/albumin hydrogels that did not dissolve even after eight months. The degradation products of all samples turned to be non-cytotoxic. All these results led us to conclude that PAA-based hydrogels have a definite potential as degradable matrices for biomedical applications.     

Development of a series of cross-linking agents that effectively stabilize alpha-helical structures in various short peptides

A series of cross-linking agents of varying rigidity and length were designed to stabilize helical structures in short peptides and were then synthesized. The sequences of the short peptides employed in this study each include two X residues (X=Dap, Dab, Orn, and Lys) at the i/i+4, i/i+7, or i/i+11 positions to provide the sites for cross-linking. These peptides were subjected to reaction with the synthesized cross-linking agents, and the helical content of the resulting cross-linked peptides were analyzed in detail by circular dichroism. For each of the peptide classes we found combinations with the cross-linking agents suitable for the construction of stable helical structures up to >95 % helicity at 5 degrees C. Our method could also be applied to biologically related sequences seen in native proteins such as Rev.     

Interpenetrating polymer network (IPN) nanogels based on gelatin and poly(acrylic acid) by inverse miniemulsion technique: synthesis and characterization

Novel interpenetrating polymer network (IPN) nanogels composed of poly(acrylic acid) and gelatin were synthesised by one pot inverse miniemulsion (IME) technique. This is based on the concept of nanoreactor and cross-checked from template polymerization technique. Acrylic acid (AA) monomer stabilized around the gelatin macromolecules in each droplet was polymerized using ammonium persulfate (APS) and tetramethyl ethylene diamine (TEMED) in 1:5 molar ratio and cross-linked with N,N-methylene bisacrylamide (BIS) to form semi-IPN (sIPN) nanogels, which were sequentially cross-linked using glutaraldehyde (Glu) to form IPNs. Span 20, an FDA approved surfactant was employed for the formation of homopolymer, sIPN and IPN nanogels. Formation of stable gelatin-AA droplets were observed at 2% surfactant concentration. Dynamic light scattering (DLS) and scanning electron microscopy (SEM) studies of purified nanogels showed small, spherical IPN nanogels with an average diameter of 255 nm. In contrast, sIPN prepared using the same method gave nanogels of larger size. Fourier-transform infrared (FT-IR) spectroscopy, SEM, DLS, X-ray photoelectron spectroscopy (XPS) and zeta potential studies confirm the interpenetration of the two networks. Leaching of free PAA chains in sIPN upon dialysis against distilled water leads to porous nanogels. The non-uniform surface of IPN nanogels seen in transmission electron microscopy (TEM) images suggests the phase separation of two polymer networks. An increase of N/C ratio from 0.07 to 0.17 (from PAA gel to IPN) and O/C ratio from 0.22 to 0.37 (from gelatin gel to IPN) of the nanogels by XPS measurements showed that both polymer components at the nanogel surface are interpenetrated. These nanogels have tailoring properties in order to use them as high potential drug delivery vehicles for cancer targeting.     

Cross-linking-induced permanently perpendicular helix orientation in surface-grafted polyglutamate films

Using a chemical cross-linking procedure, surface-grafted polyglutamate films with a permanently perpendicular helix orientation were prepared. A surface-grafted alpha-helical polyglutamate film containing polymerizable side groups was synthesized by ring-opening terpolymerization of 50 molar% gamma-methyl-L-glutamate N-carboxyanhydride (NCA), 30% gamma-stearyl-L-glutamate NCA and 20% gamma-4-vinylbenzyl-L-glutamate NCA initiated from a silicon substrate functionalized with primary amino groups. The average tilt angle of the end-grafted helices in this film is approximately 66 degrees , indicating a nearly parallel helix orientation with respect to the substrate surface. After swelling of the grafted terpolyglutamate film in stearyl methacrylate and subsequent radical cross-linking, the average helix tilt angle decreases to about 11 degrees, indicating an almost perpendicular helix orientation. The film thickness increases accordingly from 151 A before to approximately 390 A after cross-linking. Extensive solvent treatment of the cross-linked film shows that the perpendicular helix orientation is permanent.     

Investigation of the swelling behavior of hydrogels derived from high-molecular-weight poly(2-ethyl-2-oxazoline)

Thermoresponsive hydrogels are of great importance as smart materials. They are usually composed of cross-linked polymers with a lower critical solution temperature (LCST). Although much is known about networks of poly(N-isopropylacrylamide), all other polymers are somewhat neglected. In this work, the temperature-dependent swelling behavior of differently cross-linked thermoresponsive poly(2-ethyl-2-oxazoline) (PEtOx) hydrogels were investigated with regard to varying parameters of the network composition. It was found that the degrees of swelling of the hydrogels converge for a certain polymer/solvent system at a distinct temperature independent of its degree of cross-linking. Furthermore, this temperature correlates with the LCST of the respective starting PEtOx. Its net chain molecular weight M_c only affects the maximum degree of swelling and thus, the swelling–deswelling rate of the hydrogel. The fundamental structure/property relations found in this study could be useful to predict the behavior of other thermoresponsive hydrogels.     

Influence of resin cross-linking on solid-phase chemistry

A range of PS-DVB resins were prepared by suspension polymerization with styrene, p-chloromethyl styrene, and DVB. Yields of polymerization increased (from 40% to almost 80%) with increasing cross-linking. The beads exhibited the expected swelling characteristics, with the 0.3% resin swelling to almost 9 times its dry volume in CHCl3. Kinetics of cleavage of the dye Methyl Red from the range of Rink linked resins showed rate enhancements of up to 500% between the 6.0 and the 0.3% cross-linked resins. Total synthesis of Kawaguchipeptin B was carried out on the resins, and their performance during the syntheses was investigated. Contrary to expectations, the purities of the cyclic peptide product increased with increasing resin cross-linking doubling from the 0.3-6.0% resin. A Suzuki reaction showed the half-lives of reaction increased with increasing resin cross-linking with an 11-fold increase in half-life between the 0.3-2.7% resin. Surprisingly, we observed very little reaction in the case of the 3.0 and 6.0% cross-linked resins.     

Needleless electrospinning of poly(acrylic acid) superabsorbent: Fabrication,characterization and swelling behavior

In this work, nanofibrous hydrogel has been fabricated from needleless electrospinning of Poly(acrylic acid) (PAA) in an aqueous solution with different concentrations. First, all solution samples were characterized for pH, surface tension, conductivity and viscosity. Next, electrospinnability of the PAA-water dope solution was investigated using the needleless electrospinning technique under constant conditions. Results indicated that the PAA-water solution was not electrospinnable. Therefore, the neutralization of carboxylic groups in the PAA chemical structure using the NaOH solution was investigated to enhance the PAA electrospinnability. Morphology observation revealed that the fiber diameters ranged from 40 to 250 nm and increased with increasing the solution concentrations. Increasing the neutralization degree (10%, 15% and 20% with 50 wt% NaOH solution) led to increase the dope viscosity and conductivity. The resultant nanofibers could be rendered water-insoluble by incorporating 1,4-butanediol diglycidyl-ether in the PAA-water dope solution, then heat-induced crosslinking was performed using a microwave at different curing times (1–5 min) and temperatures (45–105 °C). The nanofibrous hydrogel mat was then characterized by FTIR. The resulting nanofibrous hydrogel showed remarkable water absorption capacity up to 17,000% and 51,000% (within 15 min) in the standard saline solution and distilled water, respectively.