Non-enzymatic electrochemical detection of glycerol on boron-doped diamond electrode

A non-enzymatic direct electrochemical glycerol detection method at a commercial boron-doped diamond (BDD) electrode in 0.1 M NaOH supporting electrolyte was developed. All the used electrochemical techniques proved useful features for the oxidation and direct amperometric determination of glycerol at a BDD electrode in 0.1 M NaOH aqueous solution. It was found that the direct electrooxidation of glycerol on the BDD electrode requires both adsorbed glycerol and hydroxyls at the electrode surface. Also, the sp(2) carbon did not allow enhancement of the glycerol oxidation process. The electronalytical sensitivity for the determination of glycerol at the BDD electrode ranged from 0.040 to 0.226 μA mM(-1) as a function of the technique used. The highest electroanalytical sensitivity for the determination of glycerol at the BDD electrode was reached in batch system amperometric quantification under stirring conditions. Performed recovery studies indicated that it is possible to determine glycerol in real samples, and the proposed batch system analysis-based methodology can be a valuable tool for practical glycerol analysis.     

Ab initio calculation and electrochemical verification of a passivated surface on copper with defects in 0.1 M NaOH

The thermodynamic character and dynamic behavior of vacancies in a passivated copper surface were investigated by calculations and experiments, and the data were interpreted in terms of the Point Defect Model (PDM). Both the experimental and computational results show that the principal vacancy in the passive film on copper formed anodically in 0.1 M NaOH solution is the copper vacancy and the diffusion coefficient of the copper vacancy is of the order of 10^− 17 cm²/s.     

Rapid determination of paeoniflorin and three sugars in Radix Paeoniae Alba by capillary electrophoresis.

A method based on capillary electrophoresis with electrochemical detection has been developed for the separation and determination of paeoniflorin, sucrose, glucose, and fructose in traditional Chinese medicine, Radix Paeoniae Alba. The effects of several important factors, such as the concentration of NaOH, the separation voltage, the injection time, and the detection potential, were investigated to determine the optimum conditions. The detection electrode was a 300-microm diameter copper disc electrode at a working potential of +0.60 V (versus SCE). The four analytes can be well separated within 8 min in a 40 cm length fused-silica capillary at a separation voltage of 12 kV in a 75 mM NaOH aqueous solution. The relation between the peak current and the analyte concentration was linear over about 3 orders of magnitude with detection limits (S/N = 3) ranging from 1 to 2 microM for all analytes. The proposed method has been successfully applied for the determination of the paeoniflorin and sugars in real plant samples with satisfactory assay results.     

Cyclic voltammetry of copper in sodium hydroxide solutions

The cyclic voltammograms of the Cu electrode were, obtained in NaOH solution as a function of the voltage scanning rate, electrolyte concentration and voltage range. A correlation was made between three well-defined anodic peaks and their corresponding cathodic ones. The anodic peaks were found to correspond successively to the formation of a monolayer of Cu₂O, formation of a thick multilayer film of CuO and finally Cu₂O₃ upon which O₂ is evolved. It is suggested that CuO is formed from the oxidation of Cu₂O and/or direct oxidation of metallic copper.Below 0.1 M NaOH the ratio of anodic to cathodic charges was found to be about unity, indicating the quantitative reduction of solid oxidation products, while at higher alkali concentrations higher charge ratios were obtained due to increasing proportions of soluble reaction products.The behaviour of the copper electrode in NaOH was found to be quite complicated. Thus, no simple relations were found between the voltage scanning rate and both the peak current and peak potential or between the peak current and the alkali, concentration. Further work is needed to obtain a definitive explanation of this behaviour.     

聚苯并咪唑-漆酶复合物修饰电极无电子传递媒介体催化氧还原性能

采用循环伏安法将聚苯并咪唑和漆酶的复合物共沉积在玻碳电极表面。 制备的漆酶基电极在O2气饱和的磷酸盐缓冲液中可以观察到明显的催化还原电流,实现了无媒介体的酶-电极间直接电子迁移,电极静止时氧还原起始电位为645 mV,近于漆酶活性位T1的式电位580 mV,而极限扩散催化电流密度可达318.5×10-6 A/cm2。 但由于O2气在致密的固酶导电聚合物修饰层中扩散不够快(扩散系数只有在溶液中的1.25％),导致电极以较高速度旋转时极限扩散催化电流密度仅仅增加到1×10-3 A/cm2。 根据静态时极限催化电流密度求算得到的固定漆酶催化氧还原平均转化率为21.7/s。 这种漆酶基电极具有良好的重现性和长期使用性(储存10 d后催化活力仍然保持了初始值的80％以上),在人体生理温度和弱酸性条件下具有最佳催化活力。 这种漆酶基电极作为氧传感器具有良好的传感性能：检测限低(0.5 μmol/L),灵敏度高(71.1 μA·L/mmol),且对O2具有良好的亲和力(KM=89.9 μmol/L)。     

Parameters of electrolysis in 3D flow electrode in limiting diffusion current mode

The analytical expressions were derived to calculate thickness of a three-dimensional flow electrode (TFE) working in limiting diffusion current mode in the cases of unidirectional and multidirectional electric field and solution flow for the given degree of metal extraction. The algorithm was suggested on the basis on the derived formulas and earlier published mathematical models of nonstationary electrolysis at TFE to calculate the whole electrode working conditions at the limiting diffusion current with parallel electrochemical reactions. The calculations and experimental studies were carried out on copper electrodeposition from sulfate electrolyte on TFE working in the limiting diffusion current mode. The effect of major electrochemical reactions to the distribution of potential and partial current densities by the electrode thickness was demonstrated. The process potential distribution was given for various electrode conductivities. A good compliance was shown between the results of calculations and experimental studies.     

Large amplitude Fourier transformed AC voltammetric investigation of the active state electrochemistry of a copper/aqueous base interface and implications for electrocatalysis

The higher harmonic components available from large-amplitude Fourier-transformed alternating current (FT-ac) voltammetry enable the surface active state of a copper electrode in basic media to be probed in much more detail than possible with previously used dc methods. In particular, the absence of capacitance background current allows low-level Faradaic current contributions of fast electron-transfer processes to be detected; these are usually completely undetectable under conditions of dc cyclic voltammetry. Under high harmonic FT-ac voltammetric conditions, copper electrodes exhibit well-defined and reversible premonolayer oxidation responses at potentials within the double layer region in basic 1.0 M NaOH media. This process is attributed to oxidation of copper adatoms (Cu*) of low bulk metal lattice coordination numbers to surface-bonded, reactive hydrated oxide species. Of further interest is the observation that cathodic polarization in 1.0 M NaOH significantly enhances the current detected in each of the fundamental to sixth FT-ac harmonic components in the Cu*/Cu hydrous oxide electron-transfer process which enables the underlying electron transfer processes in the higher harmonics to be studied under conditions where the dc capacitance response is suppressed; the results support the incipient hydrous oxide adatom mediator (IHOAM) model of electrocatalysis. The underlying quasi-reversible interfacial Cu*/Cu hydrous oxide process present under these conditions is shown to mediate the reduction of nitrate at a copper electrode, while the mediator for the hydrazine oxidation reaction appears to involve a different mediator or active state redox couple. Use of FT-ac voltammetry offers prospects for new insights into the nature of active sites and electrocatalysis at the electrode/solution interface of Group 11 metals in aqueous media.     

Dynamics of copper electrodeposition onto fibrous carbon electrodes

Distribution of copper electrodeposited from a sulfuric acid solution onto fibrous carbon electrodes, copper deposition rate, and current efficiency by the metal were studied in relation to the electrolysis duration, electrical conductivity of the electrode, geometric current density, and solution flow rate. The variation of the electrode thickness on which copper ions discharge at the limiting diffusion current at various solution flow rates and the electrode thickness on which the whole amount of oxygen dissolved in the electrolyte is reduced were calculated in relation to the solution flow rate and geometric current density. The main factors governing the distribution of copper across the electrode thickness and the electrolysis parameters from the beginning of the process till ??clogging?? of a part of the electrode by the metal were determined.     

Growth kinetics of single copper crystals: the concentration dependence

The growth of single copper crystals electrodeposited on a tungsten electrode is studied at different concentrations of copper ions in the electrolyte solution. Information is obtained on the diffusion coefficient of copper ions, the exchange current density at the crystal-solution phase boundary and the charge transfer coefficient at a constant temperature.     

Synthesis and growth mechanism of Bi2S3 nanoribbons

This article describes a facile solvothermal method by using mixed solvents for the large-scale synthesis of Bi(2)S(3) nanoribbons with lengths of up to several millimeters. These nanoribbons were formed by a solvothermal reaction between Bi(III)-glycerol complexes and various sulfur sources in a mixed solution of aqueous NaOH and glycerol. HRTEM (high-resolution transmission electron microscopy) and SAED (selective-area electron diffraction) studies show that the as-synthesized nanoribbons had predominately grown along the [001] direction. The Bi(2)S(3) nanoribbons prepared by the use of different sulfur sources have a common formation process: the initial formation of NaBiS(2) polycrystals, which serve as the precursors to Bi(2)S(3), the decomposition of NaBiS(2), and the formation of Bi(2)S(3) seeds in the solution through a homogeneous nucleation process; the growth of Bi(2)S(3) nanoribbons occurs at the expense of NaBiS(2) materials. The growth mechanism of millimeter-scale nanoribbons involves a special solid-solution-solid transformation as well as an Ostwald ripening process. Some crucial factors affect nanoribbon growth, such as, solvothermal temperature, volume ratio of glycerol to water, and the concentration of NaOH; these have also been discussed.     

氧气在碱溶液中结构与扩散系数的分子动力学模拟

采用分子动力学方法对不同温度(25-120 ℃)及碱浓度(1:100-1:5, 摩尔比)下NaOH和KOH溶液中的氧气进行了模拟. 本文考察了NaOH及KOH溶液中溶剂-溶剂、氧气-溶剂及氧气-溶质的径向分布函数, 并采用爱因斯坦方程从均方位移曲线中计算得到了氧气及溶质离子的扩散系数. 结果显示随着碱浓度的升高, 氧气扩散系数逐渐减少; 在相同条件下, 氧气在NaOH溶液中扩散系数小于在KOH溶液中的扩散系数; 溶质离子扩散系数的变化规律与氧气一致. 通过与现有实验结果对比, 发现了分子动力学方法的可靠性及用于研究实验受限领域的优越性.     

甘油脱水合成丙烯醛ZSM-5催化剂的孔结构和酸性调控

研究了ZSM-5 孔结构和表面酸性对甘油脱水合成丙烯醛反应性能的影响. 在碱浓度为0.2 mol·L^-1的NaOH溶液中, 分别在65和85 ℃条件下对ZSM-5进行化学刻蚀, 成功地制备了含微介孔的ZSM-5催化剂, 提高了催化剂的表面强酸密度. 碱处理后的ZSM-5催化剂在甘油脱水反应中的稳定性得到显著提高, 在ZSM-5-at85 (经85 ℃碱处理的ZSM-5)催化剂上甘油转化率在反应10 h 后仍可保持95%以上, 丙烯醛选择性达到78%. 采用N₂吸附-脱附等温线、X射线粉末衍射(XRD)、²⁷Al 固体核磁共振(²⁷Al MAS-NMR)和透射电子显微镜(TEM)等手段对ZSM-5 结构和表面性质进行了表征, 实验结果表明在碱处理过程中骨架中的硅发生了溶脱现象, 在分子筛表面上形成了大量介孔, 但是ZSM-5 的MFI 拓扑结构没有发生变化, 骨架中的大部分铝得到保持. X射线光电子能谱(XPS)、X射线荧光光谱(XRF)和氨气程序升温脱附(NH₃-TPD)证实了在碱处理后ZSM-5分子筛外表面的Si/Al 摩尔比低于其骨架中的比例, 由此表明脱硅现象主要发生在ZSM-5 的外表面, 在新产生的介孔区域由于Si/Al 摩尔比的降低使得强酸密度得到提高. 具有微介孔结构和较高酸密度的ZSM-5催化剂增强了反应物扩散性能和容碳能力, 这对于提高甘油脱水合成丙烯醛催化剂的活性和稳定性起到了关键作用.     

氯化钠溶液中铜丝尺寸效应对腐蚀行为的影响

为了研究半径变化对铜丝腐蚀行为的影响, 通过极化曲线和交流阻抗测试方法研究了半径为0.04-0.82 mm的铜丝在自然通气的0.5 mol·L-1 NaCl(pH=7.4)溶液中的腐蚀行为. 结果表明, 当铜丝半径小于氧的扩散层厚度(0.56 mm)时, 随着半径减少, 非线性扩散的存在加速了电化学反应的传质过程, 其影响由慢到快迅速增大, 使得受扩散过程控制的阴、阳极反应速率增大, 铜丝的腐蚀电流密度显著增加. 对铂丝、不锈钢丝的氧阴极还原反应过程研究也得到了类似的反应特征. 上述现象表明铜丝腐蚀行为的尺寸效应具有一定的普遍性.     

STM针尖诱导铜表面纳米刻蚀与沉积

扫描隧道显微技术 ( STM)不但可在小至原子分辩的尺度上现场研究电极表面及其结构变化 ,还能对电极表面进行纳米尺度上的加工、修饰 [1～ 3] .由于 STM探针与被研究样品的表面仅相距～ 1 nm,探针附近区域电极 /溶液界面的结构和性质将不可避免地受到影响 .尽管人们已认识到针尖与样品表面不可忽视的相互作用 ,但利用该相互作用诱导纳米区域电化学反应的研究还很少 ,仅有半导体 Si[4～ 7] 和 Ga As[8] 表面基于强电场诱导或空穴注入的 STM针尖诱导纳米刻蚀等的报道 .本文在控制铜的电位负于其热力学平衡电位 ( Nernst电位 )的情况下 ,…     

Use of a copper electrode in alkaline medium as an amperometric sensor for sulphite in a flow-through configuration

A flow injection analysis (FIA) method has been developed for the determination of sulphite in beverages. The method is based on the amperometric detection (0.60 V vs Ag/AgCl (sat. NaCl)) of the analyte at a copper surface in an alkaline medium (1 M NaOH solution) with a manifold that incorporates flow extraction of sulphite as SO2 through a PTFE membrane. Under optimal experimental conditions the peak current response increases linearly with sulphite concentration over the range from 1.0 to 5.0 mM. The repeatability of the electrode response in the FIA configuration was evaluated as 4% ( n =20), the limit of detection of the method was 0.04 mM (S/N =3) and the analytical frequency was 50 h(-1). Since ethanol is also electroactive and permeates through the PTFE membrane, a strategy involving in a first step measurements of only ethanol by manipulating the pH of the donor stream was employed for wine samples. Then, both ethanol and sulphite were measured at the copper electrode at 0.40 V vs Ag/AgCl (sat. NaCl) and the sulphite concentration was determined by difference. Results for 3 different beverage samples (alcoholic and non-alcoholic) showed excellent agreement with the ones obtained by using a recommended procedure for sulphite analysis.     

Electrocrystallizations of copper on glassy carbon in CuCl2 silica sol and aqueous solutions

Electrocrystallizations of copper from both CuCl₂ silica sol and aqueous solutions were studied by the chronoamperometry technique.It was found that current density contributions of the double-layer charging（iDL） in current-time transients（CTTs） from both of the solutions were large.An adsorption-nucleation based model was proposed to analyze quantitatively the CTTs,by which copper electrocrystallization mechanism was characterized as progressive nucleation with 3D growth（3DP） under diffusion control.The diffusion coefficient of copper ions and the AN_∞products in aqueous solutions were larger than that in silica sols, which indicated that copper nucleation was inhibited in sol solution.The large iDL may be resulted from the adsorption of chloride ions on the electrode surface.     

A dual-electrode approach for highly selective detection of glucose based on diffusion layer theory: experiments and simulation

A dual-electrode configuration for the highly selective detection of glucose in the diffusion layer of the substrate electrode is presented. In this approach, a glassy carbon electrode (GCE, substrate) modified with a conductive layer of glucose oxidase/Nafion/graphite (GNG) was used to create an interference-free region in its diffusion layer by electrochemical depletion of interfering electroactive species. A Pt microelectrode (tip, 5 microm in radius) was located in the diffusion layer of the GNG-modified GCE (GNG-G) with the help of scanning electrochemical microscopy. Consequently, the tip of the electrode could sense glucose selectively by detecting the amount of hydrogen peroxide (H2O2) formed from the oxidization of glucose on the glucose oxidase layer. The influences of parameters, including tip-substrate distance, substrate potential, and electrolyzing time, on the interference-removing efficiency of this dual-electrode approach have been investigated systematically. When the electrolyzing time was 30 s, the tip-substrate distance was 1.8 a (9.0 microm) (where a is the radius of the tip electrode), the potentials of the tip and substrate electrodes were 0.7 V and 0.4 V, respectively, and a mixture of ascorbic acid (0.3 mM), uric acid (0.3 mM), and 4-acetaminophen (0.3 mM) had no influence on the glucose detection. In addition, the current-time responses of the tip electrode at different tip-substrate distances in a solution containing interfering species were numerically simulated. The results from the simulation are in good agreement with the experimental data. This research provides a concept of detection in the diffusion layer of a substrate electrode, as an interference-free region, for developing novel microelectrochemical devices.     

Use of binary metal deposits on a cylindrical carbon-fiber microelectrode in the voltammetric determination of metal ions

The effect of binary metal deposits on a cylindrical carbon-fiber microelectrode on the determination of metals by direct and stripping voltammetry was studied. The electrolytic deposition of a binary system of copper and thallium, cadmium, lead, or mercury on the electrode in an alkaline solution resulted in the disappearance of the electroreduction peak of dissolved oxygen in the potential range from -0.8 to -1.4 V and in a decrease in the background current. Under the conditions of limited diffusion, the peak currents of Ni(II), Co(II), and Zn(II) in differential pulse voltammograms were 3–7 times higher than those calculated for a reversible electrode process under the conditions of semi-infinite diffusion. Because of this, the determination limit for metal ions in direct voltammetry was lowered to 1 X 10^-6 M. With a binary copper-thallium system, the peak current of zinc(II) reduction can be be detected in the presence of 5000-fold molar amounts of copper(II). The deposition of binary copper-lead and copper-thallium systems under the conditions of limited diffusion reduced the effect of negative interaction between the components of these systems and made possible the determination of lead(II) and thallium(I) by stripping voltammetry using additional peaks.     

液滴在超疏水植物叶面的沉积：实验和分子动力学模拟

农药液滴在靶标植物叶面的动态沉积对于提高农药利用率具有重要的意义,特别是在超疏水植物叶面的动态沉积。在本文中,我们利用生物基表面活性剂和甘油之间的氢键作用来增强液滴在超疏水植物叶面的有效沉积。在较低浓度的山梨醇-烷基胺表面活性剂溶液中,添加0.001%的甘油,可有效抑制液滴在不同超疏水/疏水植物叶片表面的弹跳和飞溅行为。结果表明,甘油的加入并没有显著改变山梨醇-烷基胺表面活性剂溶液的表面张力、粘度和聚集体的形态。核磁共振波谱(DOSY)显示,甘油加速了山梨醇-烷基胺表面活性剂分子的扩散速度。利用分子动力学模拟,对山梨醇-烷基胺表面活性剂/甘油体系的能量演化及表面活性剂相对于固体表面距离的分布进行了研究。这项目工作不仅为抑制液滴在植物叶面的弹跳飞溅提供了一种建设性的方法,而且为选择农用表面活性剂提供了理论基础。     

Scanning Electrochemical Microscopy as an In Vitro Technique for Measuring Convective Flow Rates Across Dentine and the Efficacy of Surface Blocking Treatments

Scanning electrochemical microscopy (SECM) is shown to be a powerful technique for both the measurement of local solution velocities through human dentine slices, in vitro, and for assessing quantitatively the effect of surface treatments on the flow process. SECM employs a small ultramicroelectrode (micron dimensions) as an imaging probe to provide information on the topography and transport characteristics of dentine, with high spatial resolution. In these studies the dentine sample is a membrane in a two compartment cell, which contains solutions of identical composition, including a redox active mediator (Fe(CN) . In the absence of an applied pressure, the transport‐limited current response at the probe electrode is due to diffusion of Fe(CN) to the UME, which depends on the probe to sample separation. Under an applied hydrostatic pressure, hydrodynamic flow across the sample enhances mass transport to the UME. With this methodology it was possible to accurately measure effective fluid velocities, by recording tip currents with and without pressure, and assess the efficacy of potential flow retarding agents for the treatment of dentinal hypersensitivity. For native dentine, the solution velocity was found to vary dramatically with location on the sample. The application of a glycerol monooleate ‐ base paste treatment to the surface of dentine was found to lower local flow velocities significantly. This electroanalytical methodology is simple to implement and is generally applicable to assessing the efficacy and mode of action of a wide variety of potential fluid flow retarding agents.