Structural analysis of sonochemically prepared PtRu versus Johnson Matthey PtRu in operating direct methanol fuel cells

Sonochemically prepared PtRu (3 : 1) and Johnson Matthey PtRu (1 : 1) were analyzed by X-ray absorption spectroscopy in operating liquid feed direct methanol fuel cells. The total metal loadings were 4 mg cm(-2) unsupported catalysts at the anode and cathode of the membrane electrode assembly. Ex situ XRD lattice parameter analysis indicates partial segregation of the Ru from the PtRu fcc alloy in both catalysts. A comparison of the in situ DMFC EXAFS to that of the as-received catalyst shows that catalyst restructuring during DMFC operation increases the total metal coordination numbers. A combined analysis of XRD determined grain sizes and lattice parameters, ex situ and in situ EXAFS analysis, and XRF of the as-received catalysts enables determination of the catalyst shell composition. The multi-spectrum analysis shows that the core size increases during DMFC operation by reduction of Pt oxides and incorporation of Pt into the core. This increases the mole fraction of Ru in the catalyst shell structure.     

直接甲醇燃料电池阳极催化剂PtRu/C的制备和表征

用三种方法制备了PtRu/C[Pt和Ru质量分数分别为20％和10％,记为PtRu/C(20％-10％)]甲醇阳极催化剂,通过X射线衍射(XRD)和透射电镜(TEM)考察了PtRu/C催化剂的粒子大小和晶格参数的变化,利用单电池实验考察了催化剂在直接甲醇燃料电池中的催化活性.结果表明,改变溶剂的组成提高了贵金属在活性炭表面的分散度,并改善了PtRu间的相互作用,用乙二醇/水/异丙醇混合溶剂制备的PtRu催化剂金属颗粒较小,PtRu间的相互作用较强,以该催化剂作甲醇阳极的直接甲醇燃料电池的性能较好.     

PtRu/Ti anodes with varying Pt ratio: Ru ratio prepared by electrodeposition for the direct methanol fuel cell

PtRu/Ti anodes with varying Pt ratio Ru ratio were prepared by electrodeposition of a thin PtRu catalyst layer onto Ti mesh for a direct methanol fuel cell (DMFC). The morphology and structure of the catalyst layers were analyzed by SEM, EDX and XRD. The catalyst coating layer shows an alloy character. The relative activities of the PtRu/Ti electrodes were assessed and compared in half cell and single DMFC experiments. The results show that these electrodes are very active for the methanol oxidation and that the optimum Ru surface coverage was ca. 9 at.% for DMFC operating at 20 degrees C and 11 at.% at 60 degrees C. The PtRu/Ti anode shows a performance comparable to that of the conventional carbon-based anode in a DMFC operating with 0.25 M or 0.5 M methanol solution and atmosphere oxygen gas at 90 degrees C.     

In-situ X-ray absorption spectroscopy study of Pt and Ru chemistry during methanol electrooxidation

Methanol electrooxidation in a 0.5 M sulfuric acid electrolyte containing 1.0 M CH3OH was studied on 30% Pt/carbon and 30% PtRu/carbon (Pt/Ru = 1:1) catalysts using X-ray absorption spectroscopy (XAS). Absorption by Pt and Ru was measured at constant photon energy in the near edge region during linear potential sweeps of 10-50 mV/s between 0.01 and 1.36 V vs rhe. The absorption results were used to follow Pt and Ru oxidation and reduction under transient conditions as well as to monitor Ru dissolution. Both catalysts exhibited higher activity for methanol oxidation at high potential following multiple potential cycles. Correlation of XAS data with the potential sweeps indicates that Pt catalysts lose activity at high potentials due to Pt oxidation. The addition of Ru to Pt accelerates the rate of methanol oxidation at all potentials. Ru is more readily oxidized than Pt, but unlike Pt, its oxidation does not result in a decrease in catalytic activity. PtRu/carbon catalysts underwent significant changes during potential cycling due to Ru loss. Similar current density vs potential results were obtained using the same PtRu/carbon catalyst at the same loading in a membrane electrode assembly half cell with only a Nafion (DuPont) solid electrolyte. The results are interpreted in terms of a bifunctional catalyst mechanism in which Pt surface sites serve to chemisorb and dissociate methanol to protons and carbon monoxide, while Ru surface sites activate water and accelerate the oxidation of the chemisorbed CO intermediate. PtRu/carbon catalysts maintain their activity at very high potentials, which is attributed to the ability of the added Ru to keep Pt present in a reduced state, a necessary requirement for methanol chemisorption and dissociation.     

Nanostructured PtRu/C as anode catalysts prepared in a pseudomicroemulsion with ionic surfactant for direct methanol fuel cell

Nanostructured PtRu/C catalysts have been prepared from a water-in-oil pseudomicroemulsion with the aqueous phase of a mixed concentrated solution of H(2)PtCl(6), RuCl(3), and carbon powder, oil phase of cyclohexane, ionic surfactant of sodium dodecylbenzene sulfonate (C(18)H(29)NaO(3)S), and cosurfactant n-butanol (C(4)H(10)O). Two different composing PtRu/C nanocatalysts (catalyst 1, Pt 20 wt %, Ru 15 wt %; catalyst 2, Pt 20 wt %, Ru 10 wt %) were synthesized. The catalysts were characterized by transmission electron microscopy, X-ray diffractometry, X-ray photoelectron spectroscopy, and thermogravimetric analysis, and the particles were found to be nanosized (2-4 nm) and inherit the Pt face-centered cubic structure with Pt and Ru mainly in the zero valance oxidation state. The ruthenium oxide and hydrous ruthenium oxide (RuO(x)()H(y)()) were also found in these catalysts. The cyclic voltammograms (CVs) and chronoamperometries for methanol oxidation on these catalysts showed that catalyst 1 with a higher Ru content (15 wt %) has a higher and more durable electrocatalytic activity to methanol oxidation than catalyst 2 with low Ru content (10 wt %). The CV results for catalysts 1 and 2 strongly support the bifunctional mechanism of PtRu/C catalysts for methanol oxidation. The data from direct methanol single cells using these two PtRu/C as anode catalysts show the cell with catalyst 1 has higher open circuit voltage (OCV = 0.75 V) and maximal power density (78 mW/cm(2)) than that with catalyst 2 (OCV = 0.70 V, P(max) = 56 mW/cm(2)) at 80 degrees C.     

Physical and electrochemical characterizations of microwave-assisted polyol preparation of carbon-supported PtRu nanoparticles

PtRu nanoparticles supported on Vulcan XC-72 carbon and carbon nanotubes were prepared by a microwave-assisted polyol process. The catalysts were characterized by transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy (XPS). The PtRu nanoparticles, which were uniformly dispersed on carbon, were 2-6 nm in diameter. All PtRu/C catalysts prepared as such displayed the characteristic diffraction peaks of a Pt face-centered cubic structure, excepting that the 2theta values were shifted to slightly higher values. XPS analysis revealed that the catalysts contained mostly Pt(0) and Ru(0), with traces of Pt(II), Pt(IV), and Ru(IV). The electro-oxidation of methanol was studied by cyclic voltammetry, linear sweep voltammetry, and chronoamperometry. It was found that both PtRu/C catalysts had high and more durable electrocatalytic activities for methanol oxidation than a comparative Pt/C catalyst. Preliminary data from a direct methanol fuel cell single stack test cell using the Vulcan-carbon-supported PtRu alloy as the anode catalyst showed high power density.     

Size-selected synthesis of PtRu nano-catalysts: reaction and size control mechanism

A rapid synthesis method for the preparation of PtRu colloids and their subsequent deposition on high surface area carbons is presented. The reaction mechanism is shown to involve the oxidation of the solvent, ethylene glycol, to mainly glycolic acid or, depending on the pH, its anion, glycolate, while the Pt(+IV) and Ru(+III) precursor salts are reduced. Glycolate acts as a stabilizer for the PtRu colloids and the glycolate concentration, and hence the size of the resulting noble metal colloids is controlled via the pH of the synthesis solution. Carbon-supported PtRu catalysts of controlled size can be prepared within the range of 0.7-4 nm. Slow scan X-ray diffraction and high-resolution transmission electron microscopy show the PtRu catalysts to be crystalline. The Ru is partly dissolved in the face-centered cubic Pt lattice, but the catalysts also consist of a separate, hexagonal Ru phase. The PtRu catalysts appear to be of the same composition independent of the catalyst size in the range of 1.2-4 nm. Particular PtRu catalysts prepared in this work display enhanced activities for the CH(3)OH electro-oxidation reaction when compared to two commercial catalysts.     

Structural study on highly oxidized states of a water oxidation complex [RuIII(bpy)2(H2O)]2(mu-O)4+ by ruthenium K-edge X-ray absorption fine structure spectroscopy

The oxidation-induced structural change of a water-oxidizing diruthenium complex, [(bpy)(2)(H(2)O)Ru(III)(micro-O)Ru(III)(OH(2))(bpy)(2)](4+) (bpy = 2,2'-bipyridine), was investigated by means of X-ray absorption spectroscopy. Ru K-edge XANES (X-ray absorption near-edge structure) spectra from the acidic solution and solid precipitates obtained by oxidation showed that the absorption edge shifts toward higher energy with a preedge feature slightly more enhanced than those of the lower oxidation states. This indicates that the higher oxidation state has a lower symmetry due to shortening of the Ru-O bonds that originated from the water ligands. The EXAFS (extended X-ray absorption fine structure) spectra were similar to those of the lower oxidation states, whose analysis revealed the existence of short Ru-O double bonds and an almost linear Ru-O-Ru angle (169 +/- 2 degrees ). Ab initio EXAFS simulations for several possible structural models suggest that the dimeric structure is maintained during the water oxidation reaction.     

高负载率纳米Pt-Ru/C催化剂的制备和表征

以Vulcan XC-72R碳黑为载体, 通过在含十二烷基硫酸钠(SDS)的乙二醇溶液中直接还原氯铂酸和三氯化钌, 制备了负载率为60%的纳米PtRu/C催化剂. 透射电镜(TEM)和X射线衍射(XRD)分析结果表明, SDS的加入可显著改善PtRu纳米颗粒在载体表面分散性, 平均粒径达到2.7 nm. 电化学循环伏安法(CV)测试的结果显示, 利用这种方法制备的纳米PtRu/C催化剂对于甲醇氧化具有较强的抗中毒能力和较高的电催化活性.     

Preparation and characterization of nano-sized Pt-Ru/C catalysts and their superior catalytic activities for methanol and ethanol oxidation

Carbon-supported PtRu nanoparticles (Ru/Pt: 0.25) were prepared by three different methods; simultaneous reduction of PtCl(4) and RuCl(3) (catalyst I) and changing the reduction order of PtCl(4) and RuCl(3) (catalysts II and III) to enhance the performance of the anodic catalysts for methanol and ethanol oxidation. Structure, microstructure and surface characterizations of all the catalysts were carried out by X-ray diffraction (XRD), transmission electron microscopy (TEM) coupled with energy dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The results of the XRD analysis showed that all catalysts had a face-centered cubic (fcc) structure with different and smaller lattice parameters than that of pure platinum, showing that the Ru incorporates into the Pt fcc structure by different ratios in all the catalysts. The typical particle sizes of all catalysts were in the range of 2-3 nm. The most active and stable catalyst for methanol and ethanol oxidation is catalyst III, in which a large amount (more than 90%) of PtRu alloy formation was observed. It has been found that this catalyst is about 8.0 and 33.4 times more active at ～0.60 V towards the methanol and ethanol oxidation reactions, respectively, compared to the commercial Pt catalyst.     

直接甲醇燃料电池PtRuMo/C电催化剂的制备和性质

直接甲醇燃料电池PtRuMo/C电催化剂的制备和性质;直接甲醇燃料电池;电催化剂;甲醇电氧化     

The problem of Ru dissolution from Pt–Ru catalysts during fuel cell operation: analysis and solutions

Platinum–ruthenium catalysts are widely used as anode materials in polymer electrolyte fuel cells (PEMFCs) operating with reformate gas and in direct methanol fuel cells (DMFCs). Ruthenium dissolution from the Pt–Ru anode catalyst at potentials higher than 0.5?V vs. DHE, followed by migration and deposition to the Pt cathode can give rise to a decrease of the activity of both anode and cathode catalysts and to a worsening of cell performance. A major challenge for a suitable application of Pt–Ru catalysts in PEMFC and DMFC is to improve their stability against Ru dissolution. The purpose of this paper is to provide a better knowledge of the problem of Ru dissolution from Pt–Ru catalysts and its effect on fuel cell performance. The different ways to resolve this problem are discussed.     

阵列纳米管中铂:钌原子比对甲醇电催化氧化活性的影响（英文）

采用电化学沉积技术在3-氨丙基三甲基硅氧烷修饰的多孔氧化铝膜板中制备了具有不同Pt/Ru原子比的双元Pt/Ru阵列纳米管电极（NTAEs）。分别用X-射线衍射和扫描电镜表征了催化剂结构和形态。电化学结果表明：通过控制前驱沉积液的浓度可得到不同PtRu原子比的NTAEs。所制备的Pt 或 Pt/Ru合金阵列纳米电极的真实表面积大,催化活性强,有利于物质传输,对甲醇电氧化显示出显著的催化性能。实验中还系统研究了催化剂组成与CO和CH3OH电催化氧化性能的关系,发现Pt/Ru=50:50的阵列纳米管电极对CO电氧化显示出最好的催化活性;对甲醇电氧化,则Ru原子比为40%的催化剂显示最佳催化性能。     

Combinatorial discovery of new methanol-tolerant non-noble metal cathode electrocatalysts for direct methanol fuel cells

Combinatorial synthesis and screening were used to identify methanol-tolerant non-platinum cathode electrocatalysts for use in direct methanol fuel cells (DMFCs). Oxygen reduction consumes protons at the surface of DMFC cathode catalysts. In combinatorial screening, this pH change allows one to differentiate active catalysts using fluorescent acid-base indicators. Combinatorial libraries of carbon-supported catalyst compositions containing Ru, Mo, W, Sn, and Se were screened. Ternary and quaternary compositions containing Ru, Sn, Mo, Se were more active than the "standard" Alonso-Vante catalyst, Ru(3)Mo(0.08)Se(2), when tested in liquid-feed DMFCs. Physical characterization of the most active catalysts by powder X-ray diffraction, gas adsorption, and X-ray photoelectron spectroscopy revealed that the predominant crystalline phase was hexagonal close-packed (hcp) ruthenium, and showed a surface mostly covered with oxide. The best new catalyst, Ru(7.0)Sn(1.0)Se(1.0), was significantly more active than Ru(3)Se(2)Mo(0.08), even though the latter contained smaller particles.     

Pt3Ru6 clusters supported on gamma-Al2O3: synthesis from Pt3Ru6(CO)21(mu3-H)(mu-H)3, structural characterization, and catalysis of ethylene hydrogenation and n-butane hydrogenolysis

The supported clusters Pt-Ru/gamma-Al2O3 were prepared by adsorption of the bimetallic precursor Pt3Ru6(CO)21(mu3-H)(mu-H)3 from CH2Cl2 solution onto gamma-Al2O3 followed by decarbonylation in He at 300 degrees C. The resultant supported clusters were characterized by infrared (IR) and extended X-ray absorption fine structure (EXAFS) spectroscopies and as catalysts for ethylene hydrogenation and n-butane hydrogenolysis. After adsorption, the nu(CO) peaks characterizing the precursor shifted to lower wavenumbers, and some of the hydroxyl bands of the support disappeared or changed, indicating that the CO ligands of the precursor interacted with support hydroxyl groups. The EXAFS results show that the metal core of the precursor remained essentially unchanged upon adsorption, but there were distortions of the metal core indicated by changes in the metal-metal distances. After decarbonylation of the supported clusters, the EXAFS data indicated that Pt and Ru atoms interacted with support oxygen atoms and that about half of the Pt-Ru bonds were maintained, with the composition of the metal frame remaining almost unchanged. The decarbonylated supported bimetallic clusters reported here are the first having essentially the same metal core composition as that of a precursor metal carbonyl, and they appear to be the best-defined supported bimetallic clusters. The material was found to be an active catalyst for ethylene hydrogenation and n-butane hydrogenolysis under conditions mild enough to prevent substantial cluster disruption.     

Synthesis of PtRu nanoparticles from the hydrosilylation reaction and application as catalyst for direct methanol fuel cell

Nanosized Pt, PtRu, and Ru particles were prepared by a novel process, the hydrosilylation reaction. The hydrosilylation reaction is an effective method of preparation not only for Pt particles but also for other metal colloids, such as Ru. Vulcan XC-72 was selected as catalyst support for Pt, PtRu, and Ru colloids, and TEM investigations showed nanoscale particles and narrow size distribution for both supported and unsupported metals. All Pt and Pt-rich catalysts showed the X-ray diffraction pattern of a face-centered cubic (fcc) crystal structure, whereas the Ru and Ru-rich alloys were more typical of a hexagonal close-packed (hcp) structure. As evidenced by XPS, most Pt and Ru atoms in the nanoparticles were zerovalent, except a trace of oxidation-state metals. The electrooxidation of liquid methanol on these catalysts was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results concluded that some alloy catalysts showed higher catalytic activities and better CO tolerance than the Pt-only catalyst; Pt56Ru44/C have displayed the best electrocatalytic performance among all carbon-supported catalysts.     

A novel MEA architecture for improving the performance of a DMFC

Direct methanol fuel cell (DMFC) consisting of a double-catalytic layered membrane electrode assembly (MEA) provide higher performance than that with the traditional MEA. This novel structured MEA includes a hydrophilic inner catalyst layer and a traditional electrode with an outer catalyst layer, which was made using both catalyst coated membrane (CCM) and gas diffusion electrode (GDE) methods. The inner catalyst was PtRu black on anode and Pt black on cathode. The outer catalyst was carbon supported Pt–Ru/Pt on anode and cathode, respectively. Thus in the double-catalytic layered electrodes three gradients were formed: catalyst concentration gradient, hydrophilicity gradient and porosity gradient, resulting in good mass transfer, proton and electron conducting and low methanol crossover. The peak density of DMFC with such MEA was 19 mW cm⁻², operated at 2 M CH₃OH, 2 atm oxygen at room temperature, which was much higher than DMFC with traditional MEA.     

Determination of O[H] and CO coverage and adsorption sites on PtRu electrodes in an operating PEM fuel cell

A special in situ PEM fuel cell has been developed to allow X-ray absorption measurements during real fuel cell operation. Variations in both the coverage of O[H] (O[H] indicates O and/or OH) and CO (applying a novel Deltamu(L3) = mu(L3)(V) - mu(L3)(ref) difference technique), as well as in the geometric (EXAFS) and electronic (atomic XAFS) structure of the anode catalyst, are monitored as a function of the current. In hydrogen, the N(Pt)(-)(Ru) coordination number increases much slower than the N(Pt)(-)(Pt) with increasing current, indicating a more reluctant reduction of the surface Pt atoms near the hydrous Ru oxide islands. In methanol, both O[H] and CO adsorption are separately visible with the Deltamu technique and reveal a drop in CO and an increase in OH coverage in the range of 65-90 mA/cm(2). With increasing OH coverage, the Pt-O coordination number and the AXAFS intensity increase. The data allow the direct observation of the preignition and ignition regions for OH formation and CO oxidation, during the methanol fuel cell operation. It can be concluded that both a bifunctional mechanism and an electronic ligand effect are active in CO oxidation from a PtRu surface in a PEM fuel cell.     

具有高活性和突出的抗中毒性能的Pt修饰Ru/C催化剂的制备和表征(英文)

采用两步浸渍-还原法制备了一种具有高Pt利用效率,高性能的Pt修饰的Ru/C催化剂(Ru@Pt/C).对于甲醇的阳极氧化反应,该催化剂的单位质量铂的催化活性分别为Pt/C、自制PtRu/C和商业JMPtRu/C催化剂的1.9、1.5和1.4倍;其电化学活性比表面积分别为Pt/C和自制PtRu/C的1.6和1.3倍.尤为重要的是该催化剂对甲醇氧化中间体具有很好的去除能力,其正向扫描的氧化峰的峰电流密度(If)与反向扫描氧化峰的峰电流密度(Ib)之比可高达2.4,为Pt/C催化剂的If/Ib的2.7倍,表明催化剂具有很好的抗甲醇氧化中间体毒化的能力.另外,Ru@Pt/C催化剂的稳定性也高于Pt/C、自制PtRu/C和商业JMPtRu/C催化剂的稳定性.采用X射线衍射(XRD)、透射电镜(TEM)和X射线光电子能谱(XPS)对催化剂进行了表征,Pt在Ru表面的包覆结构得到了印证.Ru@Pt/C的高铂利用效率、高性能和高抗毒能力使其有望成为一种理想的直接甲醇燃料电池电催化剂.     

Observation of methanol behavior in fuel cells in situ by NMR spectroscopy

The chemical conversion of methanol in direct methanol fuel cells was followed in situ by NMR spectroscopy. Comparing data of the methanol oxidation on Pt and PtRu anode catalysts allowed the role of Ru in both Faradaic and non-Faradaic reactions to be investigated. The spatial distributions of chemicals could also be determined. (Picture: T1-T4=inlet and outlet tubes.).