微波消解-ICP-AES法测定铁矿中P和S

采用微波加热 ,在高温高压下酸消解样品 ,应用电感耦合等离子体原子发射光谱法 (ICP- AES)同时测定铁矿中杂质元素 P和 S。选用紫外区谱线 P178.2 2 1nm、S180 .6 6 9nm,避免了基体中大量存在的 Fe、Si、Al、Cu、Mn、Ca等元素的光谱干扰。通过用纯氮吹扫光谱仪光路的方法消减空气中氧对紫外线的吸收 ,获得了足够的灵敏度。该方法简便、快速、稳定可靠 ,P、S检出限分别为 0 .0 6 7、0 .0 78μg· m L-1,回收率为89.6 %— 10 0 .7% ,RSD为 1.35 %— 5 .0 5 % ,线性范围为 0 .1— 2 0 0 μg·m L-1。     

ICP-MS测定污水中银的含量

研究了ICP-MS测定污水中银的含量,其方法检出限为0.05μg/L,方法精密度RSD为1.91%—2.32%,加标回收率为98.0%—102.4%,方法简单、快速。     

ORS-ICP-MS测定工业废水中La系稀土元素

用 ORS- ICP- MS法测定工业废水中的 L a系稀土元素 ,优化了 ICP- MS测定条件 ,利用动态反应池技术 ,可降低基体干扰 ,提高灵敏度。分析方法的检出限为 0 .8— 8.2 5 ng/ L,加标回收率为 92 %— 99%。     

ICP-AES同时测定满山香子中的铜、铁、锌、钙、镁、锰和钴

电感耦合等离子体发射光谱法 (ICP- AES)测定中药满山香子中的铜、铁、锌、钙、镁、锰、钴等 7种元素的含量。研究了样品溶解酸、元素分析线的选择。各元素测定的相对标准偏差为 1.6 0 %— 6 .38% ,加标回收率为 97.0 0 %— 10 5 .0 0 % ,方法方便、可靠 ,具有良好的准确度和精密度。     

MPT-AES同时测定航空润滑油中的铝、镁和铜

微波等离子体炬原子发射光谱法 (MPT- AES)测定未使用过的航空润滑油中铝、镁和铜含量。研究了微波功率、载气流量、工作气流量、氧屏蔽气流量、酸效应、共存离子等对元素发射强度的影响 ,优化了系统参数。铝、镁和铜的检出限分别为 15 .1ng/ m L、0 .2 8ng/ m L、2 .1ng/ m L,线性范围分别为 0 .0 5—80μg/ m L、0 .0 0 1— 5 0μg/ m L、0 .0 1— 12μg/ m L ,相对标准偏差均小于 3.7% ,回收率在 95 .6 %— 10 5 .3%之间。方法准确、快速、操作简便、维持费用低。     

ICP-AES同时测定涂料中镉、铬、钴和铅

系统研究了样品灰化条件对涂料中重金属元素测定结果的影响 ,建立了 ICP- AES法同时测定涂料中镉、铬、钴、铅元素含量的方法 ,方法的线性范围为 5— 10 0 0μg/ g,检出限为 0 .1— 0 .99μg/ g,相对标准偏差为 1.5 %— 9.9% (n=7) ,加入回收率为 97.0 %— 10 1.0 %。     

ICP-AES同时测定食用菌中钙、镁、铁、锰、铜和锌

微波消化、ICP- AES法同时测定食用菌中的钙、镁、铁、锰、铜和锌。 6种元素的加标回收率为90 .5 %— 10 3% ,RSD为 0 .6 4%— 3.6 % (n=10 )。操作方便 ,分析速度快 ,结果准确     

微波消解ICP-MS测定鲜竹笋中7种微量元素

建立同时检测鲜竹笋中铬、铜、锌、砷、镉、汞、铅等7种元素的分析方法。竹笋样品在硝酸介质中经微波消解,用电感耦合等离子体质谱(ICP-MS)检测,全定量法采集数据。校准曲线线性良好,相关系数在0.9937—1.0000之间;检出限为0.005—0.202μg/L;加标回收率在88.96%—110.5%;精密度RSD小于6.09%;国家标准样品西红柿叶(GSBZ51001-94)中几种元素的测定值都在标准范围内。该方法具有灵敏、可靠、快速、准确等优点,适用于竹笋中微量元素的分析测定。     

共沉淀分离富集-ICP-AES测定饲料级硫酸铜中微量As和Pb

在氨性介质中 ,以硫酸铁铵作共沉淀剂 ,预富集硫酸铜中的微量砷、铅 ,ICP- AES测定砷、铅的含量。方法检出限可满足日常分析的需要。加标回收率 As95 .0 %— 98.8% ;Pb96 .9%— 97.5 % ;相对标准偏差As4 .4 % ;Pb5 .8%。     

开放式微波消化-ICP-MS法快速测定食品中多种微量元素

开放式微波消解系统消化食品样品 ,以 45Sc、89Y、1 1 5In、2 0 9Bi作内标元素抑制分析信号的动态漂移 ,加入 1 %异丙醇消除 C元素对 As、Se等元素的干扰 ,建立食品中多种元素同时测定的ICP- MS方法。对 4类食品 (奶粉、鹅肝酱、水果片、燕麦片 )中的 1 2种元素 (Al、Cr、Ni、Ge、As、Se、Ag、Cd、Sn、Sb、Pb、Hg)进行了直接测定 ,绝大部分回收率在 85 %— 1 1 0 %之间 ;线性相关系数均大于 0 .999;精密度 (RSD)值 <1 0 %。对国家标准物质 (SRM)进行了分析 ,测得值与标准参考值相吻合。该法灵敏度、精密度和准确度都能满足有关标准的要求 ,具有多元素同时分析、样品前处理简单、干扰少、测定快速准确 ,省事省力等优点。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.