Potentiometric measurement of ascorbate by using a solvent polymeric membrane electrode

A novel potentiometric method for the determination of ascorbate is described in this communication. It is based on ascorbate oxidation with permanganate which is continuously released from the inner reference solution of a ligand-free tridodecylmethylammonium chloride (TDMAC)-based polymeric membrane ion selective electrode (ISE). The ISE potential determined by the activity of permanganate ions released at the sample-membrane phase boundary is increased with the consumption of permanganate. The proposed membrane electrode is useful for continuous and reversible detection of ascorbate at concentrations in 0.1M NaCl ranging from 1.0 x 10(-6) to 1.0 x 10(-3)M with a detection limit of 2.2 x 10(-7)M.     

Electrochemical sensor for neurotransmitters at physiological pH using a heterocyclic conducting polymer modified electrode

We report the simultaneous determination of two neurotransmitters, norepinephrine (NEP) and serotonin (5-HT), at physiological pH using the electropolymerized film of 3-amino-5-mercapto-1,2,4-triazole modified glassy carbon (p-AMTa) electrode. A bare glassy carbon (GC) electrode fails to resolve the voltammetric signals of NEP and 5-HT due to the surface fouling caused by the oxidized products of them. However, the p-AMTa electrode not only separates the voltammetric signals of NEP and 5-HT with a potential difference of 150 mV between NEP and 5-HT but also shows higher oxidation currents for them. The simultaneous determination of NEP and 5-HT was successfully achieved at p-AMTa electrode using differential pulse voltammetry method. The amperometric current response increased linearly with increasing NEP and 5-HT concentration in the range of 1.0 × 10(-8) to 1.0 × 10(-4) M and 1.0 × 10(-8) to 5.0 × 10(-5) M, respectively, and the detection limit was found to be 1.65 × 10(-11) for NEP and 1.32 × 10(-11) M for 5-HT (S/N = 3). The p-AMTa electrode shows better recovery results for spiked NEP and 5-HT in human blood plasma samples.     

银掺杂聚L-天冬氨酸修饰电极的制备及对多巴胺的测定

利用循环伏安法将银与L-天冬氨酸聚合修饰在玻碳电极表面,制成银掺杂聚L-天冬氨酸修饰电极,研究了多巴胺在此电极上的电化学行为,建立了循环伏安法测定多巴胺的新方法.在磷酸盐缓冲溶液(PBS, pH 7.0)中,扫描速率为50 mV/s时,多巴胺在修饰电极上产生一对氧化还原峰,Epa=0.191 V,Epc=0.161 V.用循环伏安法进行测定时,峰电流与多巴胺浓度分别在3.0×10-7 ～1.0×10-5 mol/L和1.0×10-5 ～5.0×10-4 mol/L内呈良好的线性关系; 检出限为5.0×10-8 mol/L.用于药物和尿样中多巴胺的测定,结果满意.     

1,3,4-Trisubstituted-2-azetidinone Derivatives as Novel Receptors for Bismuth(III) Ion-Selective Electrodes: Application in Pharmaceutical and Glass Samples

Abstract

Polymeric membrane electrodes (PMEs) and coated graphite electrodes (CGEs) containing 1,3,4-trisubstituted-2-azetidinone derivatives as ion carriers are reported here for bismuth(III) ion selectivity. These electrodes exhibited Nernstian response for Bi³⁺ ions over a wide concentration range (5.0 × 10^?7 M to 1.0 × 10^?1 M for CGE) with a lower detection limit of 3.98 × 10^?7 M (for CGE) and wide pH range (1.3–5.0). Compared to polymeric membrane electrode, the coated graphite electrode has shown better selectivity for Bi³⁺ ions with respect to common metal ions. Proposed electrodes have been used for the estimation of Bi³⁺ ions in pharmaceutical and glass samples.     

TpPa-1/Nafion修饰电极的差分脉冲阳极溶出伏安法同时测定铜离子和汞离子

通过机械化学合成法合成了一种共价有机框架材料TpPa-1,以此作为电极材料制备化学修饰电极,研究了修饰电极的差分脉冲阳极溶出伏安法(DPASV)同时测定铜离子和汞离子。结果表明,TpPa-1/Nafion修饰电极在磷酸盐缓冲溶液中可实现对Cu^2+和Hg^2+的同时检测。Cu^2+的检出限为5.0×10^-8 mol/L线性范围为1.0×10^-7~5.0×10^-5 mol/L,R^2=0.9975。Hg^2+的检出限为1.0×10^-8 mol/L,线性范围为2.0×10^-8~1.0×10^-4 mol/L,R^2=0.9988。采用上述方法对实际样品进行检测,回收率为97.6%~105.5%,RSD均小于4.0%。     

分子印迹电位型传感器快速检测猪尿液中的克伦特罗

以盐酸克伦特罗为模板分子,采用沉淀聚合法合成了克伦特罗的分子印迹聚合物,并以其为离子载体,制得分子印迹聚合物膜克伦特罗离子选择性电极。在最优实验条件下,电极对克伦特罗阳离子的检出限可达7.0×10-8mol/L,线性范围为1.0×10-7～1.0×10-4mol/L,能斯特斜率为55.7 mV/decade。此电极具有优越的选择性、快速的响应时间以及良好的稳定性;已成功应用于实际猪尿样品中克伦特罗的测定,加标回收率为98%～107%,检测时间小于3 min。     

Highly selective dopamine quantification using a glassy carbon electrode modified with a melanin-type polymer

A highly selective dopamine quantification at a new polymer-modified electrode in the presence of large excess of ascorbic acid and 3,4-dihydroxyphenyl acetic acid (dopac) is described. The electrochemical detection was performed at a glassy carbon electrode modified with a melanin-type polymer obtained by polymerization of 3.0×10⁻³ M -dopa in 0.050 M phosphate buffer solution pH 7.40 by applying 1.00 V for 60 min. The polymeric film exhibits attractive permselectivity excluding anionic species such as potassium ferricyanide, ascorbic acid, dopac and uric acid. Cationic species such as epinephrine, norepinephrine and dopamine and neutral ones such as catechol and hydrogen peroxide can be oxidized at the polymer-modified electrode. The use of ascorbic acid in the measurement solution allows the amplification of dopamine oxidation signal due to the reduction of the electrochemically generated dopaminequinone. By using 1.0×10⁻³ M ascorbic acid, the detection limit for dopamine is 5.0 nM. The interference for the maximum physiological concentrations of ascorbic acid and dopac in nervous centers, i.e. 500 μM ascorbic acid and 50 μM dopac is 8.1 and 1.4%, respectively.     

Development of ultra-high sensitive and selective electrochemiluminescent sensor for copper(II) ions: a novel strategy for modification of gold electrode using click chemistry

A promising and highly sensitive electrochemiluminescence (ECL) sensor for the detection of Cu(2+) based on Cu(+)-catalyzed click reaction is described in this paper. Firstly, 1-azidoundecan-11-thiol was assembled on the Au electrode surface via a simple thiol-Au reaction, then the propargyl-functionalized Ru(bpy)(3)(2+)-doped SiO(2) nanoparticles (Ru-SNPs) ECL probe was covalently coupled on the electrode surfaces via click chemistry. Cu(+), the catalyst for click chemistry, is derived from the electrolytic reduction of Cu(2+)via the Bulk Electrolysis with coulometry (BE) technique and without any reductants. It is found that the ECL intensity detected from the electrode surface has a linear relationship with the logarithm of Cu(2+) concentration in the range of 1.0 × 10(-15) to 1.0 × 10(-11) M with a detection limit of 1.0 × 10(-16) M. Also, the method is highly specific even in the presence of high concentrations of other metal cations. It has been applied to detect trace Cu(2+) in complex samples (hepatoma cell) without sample treatment.     

Dopamine and Glucose Sensors Based on Glassy Carbon Electrodes Modified with Melanic Polymers

This work deals with the study of polymers electrogenerated from different catechols at glassy carbon electrodes and the analytical applications of the resulting modified electrodes for dopamine quantification and glucose biosensing. The electropolymerization was performed from a 3.0×10^?3 M catechol solution (catechol, dopamine, norepinephrine, epinephrine or L ‐dopa in a 0.050 M phosphate buffer pH 7.40) by applying 1.00 V for 60 min. The properties of the polymers are very dependent on the nature of the catechol, L ‐dopa being the best. Glassy carbon electrodes modified with melanic polymers electrogenerated from L ‐dopa and norepinephrine were found to be suitable for dopamine determinations in flow systems, although the behavior was highly dependent on the nature of the monomer. Detection limits of 5.0 nM dopamine and interferences of 9.0 and 2.6% for 5.0×10^?4 M ascorbic acid and 5.0×10^?5 M dopac, respectively, were obtained at the glassy carbon electrode modified with a melanin‐type polymer generated from L ‐dopa (using 1.0×10^?3 M AA in the measurement solution). The advantages of using a melanin‐type polymer generated from dopamine to improve the selectivity of glucose biosensors based on carbon paste electrodes containing Pt and glucose oxidase (GOx) are also discussed. The resulting bioelectrodes combines the high sensitivity of metallized electrodes with the selectivity given by the polymeric layer. They exhibit excellent performance for glucose with a rapid response (around 10 seconds per sample), a wide linear range (up to 2.5×10^?2 M glucose), low detection limits (143 μM) and a highly reproducible response (R.S.D of 4.9%). The bioelectrodes are highly stable and almost free from the interference of large excess of easily oxidizable compounds found in biological fluids, such as ascorbic acid (AA), uric acid (UA) and acetaminophen.     

2,6-bis-methylsulfanyl-[1,3,5]thiadiazine-4-thione as a Ag+-selective ionophore.

A silver ion-selective electrode was prepared with a polymeric membrane incorporating 2,6-bis-methylsulfanyl-[1,3,5]thiadiazine-4-thione as an ionophore, tri-n-butylphosphate (TBP) as a plasticizer and sodium tetraphenylborate (NaTPB) as an additive. The electrode exhibited a near-Nernstian response of 52 mV/decade over a wide linear concentration range of 1.0 x 10(-5) - 1.0 x 10(-1) M with a lower detection limit of 9.77 x 10(-6) M. The electrode exhibited excellent selectivity for silver ion over many of the alkali, alkaline-earth and transition metal ions. The electrode worked well over a wide pH range of 1.77 - 7.13. The response time of the electrode was less than 20 s. The sensor can be applied as indicator electrode for the potentiometric titration of Ag+ ions with Cl- ions.     

Mercury(II) ion-selective electrodes based on heterocyclic systems

Mercury ion-selective electrodes (ISEs) were prepared with a polymeric membrane based on heterocyclic systems: 2-methylsulfanyl-4-(4-nitro-phenyl)-l-p-tolyl-1H-imidazole (I) and 2,4-diphenyl-l-p-tolyl-1H-imidazole (II) as the ionophores. Several ISEs were conditioned and tested for the selection of common ions. The electrodes based on these ionophores showed a good potentiometric response for Hg2+ ions over a wide concentration range of 5.0 x 10(5-) - 1.0 x 10(-1)M with near-Nernstian slopes. Stable potentiometric signals were obtained within a short time period of 20 s. The detection limits, the working pH range of the electrodes were 1.0 x 10(-5) M and 1.6-4.4 respectively. The electrodes showed better selectivity for Hg2+ ions over many of the alkali, alkaline-earth and heavy metal ions. Also sharp end points were obtained when these sensors were used as indicator electrodes for the potentiometric titration of Hg2+ ions with iodide ions.     

Aluminium(III)-selective electrode based on a newly synthesized tetradentate Schiff base

A PVC membrane electrode for aluminium ion based on bis(5-phenyl azo salicylaldehyde) 2,3-naphthalene diimine (5PHAZOSALNPHN) as an ion carrier was developed. The electrode exhibits a Nernstian slope of 19.3+/-0.8 mV per decade and a linear range of 5.0x10(-6)-1.0x10(-2) M for Al(NO(3))(3). The limit of detection is 2.5x10(-6) M. It has a fast response time of about 10 s and can be used for at least 10 weeks without observing any deviation. The proposed membrane sensor revealed good selectivity for Al(3+) over a wide variety of other metal ions and could be used in pH range of 2.9-5.0. It was used as an indicator electrode in potentiometric titration of aluminium ion.     

Determination of catecholamine in human serum by a fluorescent quenching method based on a water-soluble fluorescent conjugated polymer-enzyme hybrid system

In this paper, a sensitive water-soluble fluorescent conjugated polymer biosensor for catecholamine (dopamine DA, adrenaline AD and norepinephrine NE) was developed. In the presence of horse radish peroxidase (HRP) and H(2)O(2), catecholamine could be oxidized and the oxidation product of catecholamine could quench the photoluminescence (PL) intensity of poly(2,5-bis(3-sulfonatopropoxy)-1,4-phenylethynylenealt-1,4-poly(phenylene ethynylene)) (PPESO(3)). The quenching PL intensity of PPESO(3) (I(0)/I) was proportional to the concentration of DA, AD and NE in the concentration ranges of 5.0 × 10(-7) to 1.4 × 10(-4), 5.0 × 10(-6) to 5.0 × 10(-4), and 5.0 × 10(-6) to 5.0 × 10(-4) mol L(-1), respectively. The detection limit for DA, AD and NE was 1.4 × 10(-7) mol L(-1), 1.0 × 10(-6) and 1.0 × 10(-6) mol L(-1), respectively. The PPESO(3)-enzyme hybrid system based on the fluorescence quenching method was successfully applied for the determination of catecholamine in human serum samples with good accuracy and satisfactory recovery. The results were in good agreement with those provided by the HPLC-MS method.     

Highly selective PVC-membrane electrodes based on Co(II)-Salen for determination of nitrite ion.

A cobalt(II) derivative was used as a suitable ionophore for the preparation of a polymeric membrane nitrite-selective electrode. The electrode reveals a Nemstian behavior over a very wide NO2- ion concentration range (1.0 x 10(-6)-1.0 x 10(-1) M) and a very low detection limit (5.0 x 10(-7) M). The potentiometric response is independent of the pH of solution in the pH range 4.0-9.5. The electrode shows advantages such as low resistance, fast response and, most importantly, good selectivity relative to a wide variety of inorganic and organic anions. In fact, the selectivity behavior of the proposed NO2- ion-selective electrode shows great improvements compared to the previously reported electrodes for nitrite ion. The proposed electrodes could be used for at least 2 months without any significant changes in potentials. The electrode was successfully applied to the determination of nitrate ion concentrations in sausage and milk samples.     

Studies on the Electrochemistry of Dopamine at a Pyrocatechol Sulfonephthalein Modified Glassy Carbon electrode

IntroductionThere has been a considerable interest in developing the methods to measure the secretionneurotransmitters. Electrochemical teChniques have proven to be significantly advantageous tothe biosciencesLlj. The application of ultramicroelectrodes to neuroscien.ce, which has been pioneered by Adams[2], to monitor the concentration of neurotransmitters in the central nervesystem has had a special impact. Several neurotransmitters, e. g., dopamine(DA) are electroactlve and therefore can …     

二茂铁-离子液体修饰碳糊电极的研制

以室温离子液体N-辛基吡啶六氟磷酸盐为粘合剂与二茂铁和石墨粉相混合制备了一种新型二茂铁-离子液体修饰碳糊电极。以该电极为工作电极,采用循环伏安法、计时安培法研究了多巴胺(DA)在该糊电极上的电化学行为。实验结果表明:该电极在pH 5.0的乙酸-乙酸钠缓冲溶液中,外加电压0.8 V条件下,灵敏度最高。电流增量与DA浓度在1.0×10-5～1.0×10-3 mol/L范围内呈良好的线性关系,检出限为5.0×10-6 mol/L(S/N=3)。     

Polymeric membrane and coated graphite samarium(III)-selective electrodes based on isopropyl 2-[(isopropoxycarbothioyl)disulfanyl]ethanethioate

New polymeric membrane (PME) and coated graphite (CGE) samarium(III)-selective electrodes were prepared based on isopropyl 2-[(isopropoxycarbothioyl) disulfanyl]ethanethioate as a suitable neutral ionophore. The electrodes exhibit Nernstian slopes for Sm³⁺ ions over wide concentration ranges (1.0×10⁻⁵ to 1.0×10⁻¹ M for PME and 1.0×10⁻⁶ to 1.0×10⁻¹ M for CGE). The PME and CGE have limits of detection of 3.1×10⁻⁶ and 5.0×10⁻⁷ M, respectively, and response times of about 20 s. The potentiometric responses are independent of the pH of the test solution in the pH range 4.0-7.0. The proposed electrodes revealed good selectivities over a wide variety of other cations including alkali, alkaline earth, transition and heavy metal ions. The electrodes were successfully applied to the recovery of Sm³⁺ ion from tap water samples and also, as an indicator electrode, in potentiometric titration of samarium(III) ions.     

Coated wire silver-ion selective electrode based on a N,N'-bis(2-thienylmethylene)-1,2-diaminobenzene.

A novel membrane coated platinum-wire electrode (MCPWE) based on N,N'-bis(2-thienylmethylene)-1,2-diaminobenzene (BTMD) for highly selective determination of Ag+ ion has been developed. The influences of membrane composition and pH on the potentiometric responses of electrode were investigated. The potentiometric responses are independent of the pH of the test solution in the range of 5.0 - 9.0. The electrode shows a linear response for Ag+ ion over the concentration range of 1.0 x 10(-60 to 1.0 x 10(-1) M with a lower detection limit of 6.0 x 10(-7) M. The electrode possesses a Nernstian slope of 59.7 mV decade(-1) and a fast response time of < or = 17 s and can be used for at least 2 months without any observable deviation. The proposed electrode displayed very good selectivity for Ag+ ion with respect to NH4+ and alkali, alkaline earth and some common transition metal ions. The practical utility of the electrode has been demonstrated by its use as the indicator electrode in the potentiometric titration of an AgNO3 solution with a NaI solution and in determination of the silver content of a developed radiological film.     

An Eu(III) sensor based on N,N-diethyl-N-(4-hydroxy-6-methylpyridin-2-yl)guanidine.

A highly selective poly(vinyl chloride)-based membrane sensor produced by using N,N-diethyl-N-(4-hydroxy-6-methylpyridin-2-yl)guanidine (GD) as active material is described. The electrode displays Nernstian behavior over the concentration range 7.0 x 10(-5) - 1.0 x 10(-1) M. The detection limit of the electrode is 5.0 x 10(-5) M. The best performance was obtained with the membrane containing 30% PVC, 55% benzyl acetate, 5% GD and 10% oleic acid. The response of the sensor is pH-independent in the range of 3.0 - 7.0. The sensor possesses satisfactory reproducibility, fast response time (< 20 s), and specially excellent discriminating ability for Eu(III) ion with respect to the alkali, alkaline earth, transition and heavy metal ions. The membrane sensor was used as an indicator electrode in potentiometric titration of Eu(III) ion with EDTA. It was also applied in determination of fluoride ions in mouth wash preparations.     

Iodide-selective polymeric membrane electrode based on copper(Ⅱ) bis(N-2-bromophenylsalicyldenaminato) complex

A PVC membrane electrode based on copper（Ⅱ） bis（N-2-bromophenylsalicyldenaminato） as ionophor was prepared.The ion selective electrode was tested by inorganic anions and showed a good selectivity for iodide ion.This sensor exhibited Nernstian behavior with a slope of—57.8 mV per decade at 25℃.The proposed electrode showed a linear range from 1.0×10⁵ to 1.0×10^-1 mol/L with a detection limit of 5.0×10^-6 mol/L.The electrode response was independent of pH in the range of 3.0- 10.0.The proposed sensor was applied to determine the iodide in water and antiseptic samples.