Surface plasmon resonance biosensor for genetically modified organisms detection

The development of a surface plasmon resonance (SPR) affinity biosensor based on DNA hybridisation is described. This biosensor has been applied to genetically modified organisms (GMOs) detection. Single stranded DNA (ssDNA) probes were immobilised on the sensor chip of an SPR device and the hybridisation between the immobilised probe and the complementary sequence (target) was monitored. The probe sequences were internal to the sequence of 35S promoter and NOS terminator which are inserted sequences in the genome of GMO regulating the transgene expression. The system has been optimised using synthetic oligonucleotides, then applied to real samples analysis. Samples, containing the transgenic target sequences, were amplified by polymerase chain reaction (PCR) and then detected with the SPR biosensor.     

Introducing curcumin as an electrochemical DNA hybridization indicator and its application for detection of human interleukin-2 gene

In this paper, the application of curcumin (CU) as a non-toxic electrochemical DNA hybridization indicator was described. Hybridization investigations on a pencil graphite electrode surface as a transducer using oligonucleotides containing only one base type, including poly A, poly T, poly C, and poly G as probe and as related complementary/non-complementary sequences, showed that CU has no specific interaction with each of the oligonucleotides of DNA. Furthermore, results showed good interaction between CU and the hybridized form of oligonucleotides; thus, the extent of hybridization was evaluated based on the difference between differential pulse voltammetry (DPV) signals of CU accumulated on the probe-pencil graphite electrode (PGE) and CU accumulated on the probe-target-PGE. Then, the developed biosensor was successfully applied for the detection of short sequences of human interleukin-2 (hIL-2) gene as a model. A hybridization experiment with non-complementary oligonucleotide showed that the suggested DNA sensor responds selectively to the target. At optimized conditions, two linear ranges were obtained for hIL-2 gene, first from 50 to 1000 pM and second from 0.01 to 1 μM with a detection limit of 12 pM. 7.0) containing 20 mM NaCl.     

Nanostructured zirconium oxide based genosensor for Escherichia coli detection

A deoxyribonucleic acid (DNA) biosensor has been fabricated via immobilization of 17 base terminal single stranded DNA (ssDNA) identified from the 16s rRNA coding region of Escherichia coli onto sol–gel derived nanostructured zirconium oxide (NanoZrO₂) film. An oligonucleotide probe with a terminal 5′-phosphate group has been attached to the surface of the electrode via affinity of NanoZrO₂ for phosphate. The results of hybridization studies carried out with the complementary, non-complementary and genomic DNA reveal that ssDNA/NanoZrO₂/ITO bioelectrode has a high selectivity and sensitivity towards hybridization detection with limits of 10^?6–10⁶ pM of complementary DNA.     

Modeling of DNA hybridization detection using methylene blue as an electroactive label

Mathematical modeling of methylene blue (MB) signal in ssDNA and dsDNA on pencil graphite electrode is described. A DNA biosensor was developed based on MB signal. The probe and target DNAs were 20 mer oligonucleotides corresponding to consensus sequence of HPV major capsid protein L1 gene. Hybrids of various complementary and non-complementary oligonucleotides with the probe were considered as dsDNA with different hybridization degrees. Modeling was developed by incorporation of only the stable forms of dsDNA hybrids. Effect of hybridization degree on current signal in various forms was studied. A factor named AHP (Average Hybridization Percentage) for verifying the hybridization events was defined. Results showed that there is a significant mathematical relation between the calculated AHP and MB signals.     

Influences of non-selective interactions of nucleic acids on response rates of nucleic acid fiber optic biosensors

The immobilization of oligonucleotides to solid surfaces can provide a platform of chemistry that is suitable for the development of biosensor and microarray technologies. Experiments were performed using a fiber optic nucleic acid biosensor based on total internal reflection fluorescence to examine the effects of the presence of non-complementary DNA on the detection of hybridization of complementary target DNA. The work has focused on the rates and extent of hybridization in the presence and absence of non-selective adsorption using fluorescein-labeled DNA. A stop-flow system of 137 microL volume permitted rapid introduction and mixing of each sample. Response times measured were on the order of seconds to minutes. Non-selective adsorption of non-complementary oligonucleotides (ncDNA) was found to occur at a significantly faster rate than hybridization of complementary oligomers (cDNA) in all cases. The presence of ncDNA oligonucleotides did not inhibit selective interactions between immobilized DNA and cDNA in solution. The presence of high concentrations of non-complementary genomic DNA had little effect on the extent of hybridization of complementary oligonucleotides, but actually reduced the response times of sensors to cDNA oligonucleotides.     

Tethered thiazole orange intercalating dye for development of fibre-optic nucleic acid biosensors

Single-stranded DNA (ssDNA) oligonucleotide in solution, or that is immobilized onto a surface to create a biosensor, can be used as a selective probe to bind to a complementary single-stranded sequence. Fluorescence enhancement of thiazole orange (TO) occurs when the dye intercalates into double-stranded DNA (dsDNA). TO dye has been covalently attached to probe oligonucleotides (homopolymer and mixed base 10mer and 20mer) through the 5′ terminal phosphate group using polyethylene glycol linker. The tethered TO dye was able to intercalate when dsDNA formed in solution, and also at fused silica surfaces using immobilized ssDNA. The results indicated the potential for development of a self-contained biosensor where the fluorescent label was available as part of the immobilized oligonucleotide probe chemistry. The approach was shown to be able to operate in a reversible manner for multiple cycles of detection of targeted DNA sequences.     

Voltammetric determination of DNA hybridization using methylene blue and self-assembled alkanethiol monolayer on gold electrodes

An electrochemical DNA biosensor based on the recognition of single stranded DNA (ssDNA) by hybridization detection with immobilized complementary DNA oligonucleotides is presented. DNA and oligonucleotides were covalently attached through free amines on the DNA bases using N-hydroxysulfosuccinimide (NHS) and N-(3-dimethylamino)propyl-N′-ethylcarbodiimide hydrochloride (EDC) onto a carboxylate terminated alkanethiol self-assembled monolayers (SAM) preformed on a gold electrode (AuE). Differential pulse voltammetry (DPV) was used to investigate the surface coverage and molecular orientation of the immobilized DNA molecules. The covalently immobilized probe could selectively hybridize with the target DNA to form a hybrid on the surface despite the bases being attached to the SAM. The changes in the peak currents of methylene blue (MB), an electroactive label, were observed upon hybridization of probe with the target. Peak currents were found to increase in the following order: hybrid-modified AuE, mismatched hybrid-modified AuE, and the probe-modified AuE which indicates the MB signal is determined by the extent of exposed bases. Control experiments were performed using a non-complementary DNA sequence. The effect of the DNA target concentration on the hybridization signal was also studied. The interaction of MB with inosine substituted probes was investigated. Performance characteristics of the sensor are described.     

Influences of non-selective interactions of nucleic acids on response rates of nucleic acid fiber optic biosensors

The immobilization of oligonucleotides to solid surfaces can provide a platform of chemistry that is suitable for the development of biosensor and microarray technologies. Experiments were performed using a fiber optic nucleic acid biosensor based on total internal reflection fluorescence to examine the effects of the presence of non-complementary DNA on the detection of hybridization of complementary target DNA. The work has focused on the rates and extent of hybridization in the presence and absence of non-selective adsorption using fluorescein-labeled DNA. A stop-flow system of 137 μL volume permitted rapid introduction and mixing of each sample. Response times measured were on the order of seconds to minutes. Non-selective adsorption of non-complementary oligonucleotides (ncDNA) was found to occur at a significantly faster rate than hybridization of complementary oligomers (cDNA) in all cases. The presence of ncDNA oligonucleotides did not inhibit selective interactions between immobilized DNA and cDNA in solution. The presence of high concentrations of non-complementary genomic DNA had little effect on the extent of hybridization of complementary oligonucleotides, but actually reduced the response times of sensors to cDNA oligonucleotides. Received: 26 September 2000 / Revised: 24 November 2000 / Accepted: 30 November 2000     

DNA-binding small-ligand-immobilized surface plasmon resonance biosensor for detecting thymine-related single-nucleotide polymorphisms

A surface plasmon resonance (SPR) biosensor that carries DNA-binding small ligands has been developed for the detection of single-nucleotide polymorphisms (SNPs). 3,5-Diaminopyrazine derivatives, with a hydrogen-bonding profile fully complementary to the thymine base, were utilized as recognition elements on the sensor surface, and a target single-stranded DNA sequence was hybridized with a DNA probe containing an abasic site to place this site opposite a nucleobase to be detected. In a continuous flow of sample solutions buffered to pH 6.4 (0.25 M NaCl), the 3,5-diaminopyrazine-based SPR sensor can detect an orphan nucleobase in the duplex with a clear selectivity for thymine over cytosine, guanine, and adenine (5'-GTT GGA GCT GXG GGC GTA GGC-3'/3'-CAA CCT CGA CNC CCG CAT CCG-5'; X=abasic site, N=target nucleobase G, C, A, or T). The SPR response was linear in the concentration range 10-100 nM. Allele discrimination is possible based on the combination of different binding surfaces in a flow cell of the SPR system, which is demonstrated for the analysis of the thymine/cytosine mutation present in 63-meric polymerase chain reaction (PCR) amplification products (Ha-ras gene, codon 12, antisense strand). Comparison with a bulk assay based on 3,5-diaminopyrazine/DNA binding shows that the immobilization of 3,5-diaminopyrazine derivatives on the SPR sensor allows more sensitive detection of the target DNA sequence, and binding selectivity can be tuned by controlling the salt concentration of sample solutions. These features of the DNA-binding small-molecule-immobilized SPR sensor are discussed as a basis for the design of SPR biosensors for SNP genotyping.     

Nucleic acid sensor for M. tuberculosis detection based on surface plasmon resonance

Cysteine modified NH(2)-end peptide nucleic acid (PNA) (24-mer) probe and 5'-thiol end labeled deoxyribonucleic acid (DNA) probes specific to Mycobacterium tuberculosis have been immobilized onto BK-7 gold coated glass plates for the detection of complementary, one-base mismatch, non-complementary targets and complementary target sequence in genomic DNA of Mycobacterium tuberculosis using a surface plasmon resonance (SPR) technique. The DNA/Au and PNA/Au bio-electrodes have been characterized using contact angle, atomic force microscopy (AFM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetric (CV) techniques, respectively. It is revealed that there is a 252 millidegrees SPR angle change in the case of PNA immobilization and 205 millidegrees for DNA immobilization, indicating increased amount of immobilized PNA molecules. Hybridization studies reveal that there is no binding of the non-complementary target to DNA/Au and PNA/Au electrode. Compared to the DNA/Au bioelectrode, PNA/Au electrode has been found to be more efficient for detection of one-base mismatch sequence. The PNA/Au bioelectrode shows better detection limit (1.0 ng ml(-1)) over the DNA-Au bioelectrode (3.0 ng ml(-1)). The values of the association (k(a)) and dissociation rate constant (k(d)) for the complementary sequence in case of the PNA/Au bioelectrode have been estimated as 8.5 x 10(4) m(-1) s(-1) and 3.6 x 10(-3) s(-1), respectively.     

Label-free detection of DNA mutations by SPR: application to the early detection of inherited breast cancer

A screening analysis of DNA hybridization and the presence of DNA mutations using an surface plasmon resonance (SPR) biosensor is shown. The influence of lateral and vertical spacers, as well as several hybridization conditions, was studied to optimize the differentiation between fully complementary and mismatched DNA strands. Our results demonstrated that SPR biosensors were able to detect mismatch sequences related to inherited breast cancer, with high specificity and sensitivity. Using PCR synthetic sequences as targets, mutant sequences were clearly discriminated from fully complementary ones, and detection limits below 50 nM were achieved.     

Electrochemical Detection of Avian Influenza Virus Genotype Using Amino‐ssDNA Probe Modified Gold Electrodes

A DNA biosensor for the detection of specific oligonucleotide sequences of Avian Influenza Virus type H5N1 has been proposed. The NH₂‐ssDNA probe was deposited onto a gold electrode surface to form an amide bond between the carboxyl group of thioacid and the amino group from ssDNA probe. The signals generated as a result of hybridization were registered in square wave voltammetry and electrochemical impedance spectroscopy in the presence of [Fe(CN)₆]^3?/4? as a redox marker. The genosensor is capable to determine 20‐mer and 180‐bp (PCR products) oligonucleotides complementary sequences with detection limit in the fM range. The genosensor displays good selectivity and sensitivity. The 20‐mer as well as 180‐bp oligonucleotides without a complementary sequence generate very low signal.     

Electrochemical detection of a Vibrio parahaemolyticus sequence-specific gene based on a gold electrode modified with a single stranded probe

An electrochemical DNA biosensor for specific-sequences detection of Vibrio parahaemolyticus (VP) was fabricated. A single-stranded 20-mer oligonucleotide (ssDNA) and 6-mercapto-1-hexanol (MCH) were immobilized via a thiol linker on gold disk electrodes by self-assembling. The ssDNA underwent hybridization in a hybridization solution containing complementary or non-complementary or single base pair mismatched DNA sequences of VP. Examination of changes in response to these three target DNAs showed that the developed biosensor had a high selectivity and sensitivity.     

Label‐Free and Label Based Electrochemical Detection of Hybridization by Using Methylene Blue and Peptide Nucleic Acid Probes at Chitosan Modified Carbon Paste Electrodes

A chitosan modified carbon paste electrode (ChiCPE) based DNA biosensor for the recognition of calf thymus double stranded DNA (dsDNA), single stranded DNA (ssDNA) and hybridization detection between complementary DNA oligonucleotides is presented. DNA and oligonucleotides were electrostatically attached by using chitosan onto CPE. The amino groups of chitosan formed a strong complex with the phosphate backbone of DNA. The immobilized probe could selectively hybridize with the target DNA to form hybrid on the CPE surface. The detection of hybridization was observed by using the label‐free and label based protocols. The oxidation signals of guanine and adenine greatly decreased when a hybrid was formed on the ChiCPE surface. The changes in the peak currents of methylene blue (MB), an electroactive label, were observed upon hybridization of probe with target. The signals of MB were investigated at dsDNA modified ChiCPE and ssDNA modified ChiCPE and the increased peak currents were observed, in respect to the order of electrodes. The hybridization of peptide nucleic acid (PNA) probes with the DNA target sequences at ChiCPE was also investigated. Performance characteristics of the sensor were described, along with future prospects.     

Electrochemical DNA sensor by the assembly of graphene and DNA-conjugated gold nanoparticles with silver enhancement strategy

Sensitive and selective detection of DNA is in urgent need due to its important role in human bodies. Many disorders, such as Alzheimer's disease and various cancers, are closely related with DNA damage. In this work, a novel electrochemical DNA biosensor was constructed on a DNA-assembling graphene platform which provided a robust, simple and biocompatible platform with large surface area for DNA immobilization. The as-designed DNA sensor was fabricated by directly assembling captured ssDNA on a graphene-modified electrode through the π-π stacking interaction between graphene and ssDNA bases. Then, the target DNA sequence and oligonucleotide probes-labeled AuNPs were able to hybridize in a sandwich assay format, following the AuNPs-catalyzed silver deposition. The deposited silver was further detected by differential pulse voltammetry. Owing to the high DNA loading ability of graphene and the distinct signal amplification by AuNPs-catalyzed silver staining, the resulting biosensor exhibited a good analytical performance with a wide detection linear range from 200 pM to 500 nM, and a low detection limit of 72 pM. Additionally, the biosensor was proved to be able to discriminate the complementary sequence from the single-base mismatch sequence. The simple biosensor is promising in developing electronic, on-chip assays in clinical diagnosis, environmental control, and drug discovery.     

Direct selective detection of genomic DNA from coliform using a fiber optic biosensor

Fiber optic biosensors operated in a total internal reflection format were prepared based on covalent immobilization of 25mer lacZ single-stranded nucleic acid probe. Genomic DNA from Escherichia coli was extracted and then sheared by sonication to prepare fragments of approximately 300mer length. Other targets included a 25mer fully complementary lacZ sequence, 100mer polymerase chain reaction (PCR) products containing the lacZ sequence at various locations, and non-complementary DNA including genomic samples from salmon sperm. Non-selective adsorption of non-complementary oligonucleotides (ncDNA) was found to occur at a significantly faster rate than hybridization of complementary oligomers (cDNA) in all cases. The presence of ncDNA oligonucleotides did not inhibit selective interactions between immobilized DNA and cDNA in solution. The presence of high concentrations of non-complementary genomic DNA had little effect on extent or speed of hybridization of complementary oligonucleotides. Detection of genomic fragments containing the lacZ sequence was possible in as little as 20 s by observation of the steady-state fluorescence intensity increase or by time-dependent rate of fluorescence intensity changes.     

An optical surface plasmon resonance biosensor for determination of tetanus toxin

Surface plasmon resonance (SPR) has been successfully applied for the simple, rapid, and label-free assay of various biomolecules. This assay evaluates a novel wavelength modulation SPR biosensor for the detection of tetanus toxin. The wavelength modulation SPR biosensor is designed based on fixing the incident angle of light and measuring the reflected intensities in the resonance wavelength range spanning 400-800 nm simultaneously. Tetanus toxin (TeNT), one of the most potent toxins known, is synthesized as a 150 kDa single polypeptide chain. The SPR biosensor has been shown to be capable of directly detecting concentration of tetanus toxin as low as 0.028 Lf ml⁻¹. Under selected experimental conditions, the SPR biosensor has a good reproducibility, sensitivity and reversibility. The results illustrate how wavelength modulation SPR biosensor can be used to detect biomolecular interactions.     

Detection of short oligonucleotide sequences of hepatitis B virus using electrochemical DNA hybridisation biosensor

A novel, sensitive and selective electrochemical hybridisation biosensor was developed for the detection of the hepatitis B virus (HBV) using a manganese(II) complex as electrochemical indicator and a DNA probe-modified carbon paste electrode as the biosensor (DNA/CPE). The results showed that this complex could be accumulated electrochemically the immobilised dsDNA layer rather than in the single-stranded DNA (ssDNA) layer. On the basis of this, the manganese complex was used as an electrochemical hybridisation indicator for the detection of oligonucleotides related to HBV. The hybridisation event was evaluated on the basis of the difference between the reduction signals of the manganese(II) complex with the probe DNA prior to and post hybridisation with a target sequence using a differential pulse mode. Several factors affecting the immobilisation and hybridisation of oligonucleotides as well as the indicator’s accumulation were investigated. Experiments with a non-complementary and mismatch sequences demonstrated the good selectivity of the biosensor. Using this approach, the HBV target oligonucleotide’s sequence could be quantified over arange from 0.22 ng L^?1 to 5.40 ng L^?1, with a linear correlation coefficient of 0.9994 and the limit of detection of 0.07 ng L^?1.     

Detection of mismatched caspase-3 DNA oligonucleotides with an SPR biosensor following amplification by Taq polymerase

We demonstrate that base mismatches of caspase-3 DNA sequences can be detected by surface plasmon resonance (SPR) following signal amplification by polymerase from Thermus aquaticus (Taq). The concentration of magnesium ions and the respective dNTPs for polymerase binding to the oligonucleotides on the sensing surface were optimized. Taq polymerase binds to double-stranded DNA that is self-assembled on the gold surface of the biosensor to induce an SPR signal. Experiments are presented on the effect of Mg(II) and dNTP concentrations on the activity of the polymerase on the sensing surface. The detection limits are 50 pM, 0.1 nM, 0.7 nM, 7 nM, and 20 nM for correctly matched, single-base mismatched, two-base mismatched, three-base mismatched and four-base mismatched DNA of caspase-3, respectively. This is attributed to the optimized experimental conditions, with samples containing 2 μM of Mg(II) and 0.3 mM of dNTP.

Detection of bar gene encoding phosphinothricin herbicide resistance in plants by electrochemical biosensor

An electrochemical biosensor for the detection of bar gene coding phosphinothricin herbicide resistance is presented. The detection was based on hybridization reaction between the specific to bar gene 19-mer probe immobilized on the electrode surface and complementary DNA in a sample. Single-stranded DNA probe specific to bar gene was covalently attached by 5'-phosphate end to the surface of carbon paste electrode. Outer layer of a conventional CPE was provided with carboxyl groups of stearic acid. ssDNA was coupled to the electrode through ethylenediamine with the use of water-soluble 1-ethyl-3(3'-dimethylaminopropyl)-carbodiimide and N-hydroxy-sulfosuccinimide as activating reagents. Hybridization reaction at the electrode surface was detected via Co(bpy)(3)(3+), which possess a much higher affinity to the resulting DNA duplex compared to ssDNA probe. Detection limit of the sensor was 0.1 microM of target DNA fragments and its response was linear from 5 to 20 microM. Hybridization event was also detected by measuring guanine peak but this approach presented distinctly higher detection limit (1 muM) and lower reproducibility. Complete time of one measurement with the use of the biosensor including covalent attachment of ethylenediamine (linker) and ssDNA probe to the electrode, hybridization with target and interaction with electroactive indicator was about 70 min.