Micro determination of ascorbic acid using methyl viologen

A new simple and sensitive analytical spectrophotometric method is developed for the determination of ascorbic acid reduces methyl viologen to form a stable blue coloured free radical ion. This method has a sensitivity and lower limit detection of 0.1 μg ml⁻¹ of ascorbic acid (0.1 ppm) which is comparable to the flow injection analysis reported earlier. Beer's law is obeyed over the concentration range of 1.0-10 μg ml⁻¹ of ascorbic acid per 10 ml of the final solution (0.1-1.0 μg ml⁻¹) at 600 nm. The molar absorptivity and Sandell's sensitivity were found to be 1.5 × 10⁵ ± 100 l mol⁻¹ cm⁻¹ and 0.001 μg cm⁻², respectively. The method has been applied to the determination of ascorbic acid in food, pharmaceuticals and biological samples.     

Direct spectrophotometric determination of calcium in clinical samples with carboxyazo-p-CH3

A highly sensitive and relatively interference-free spectrophotometric method for determination of calcium is described. The method is based on the reaction between calcium ions and carboxyazo-p-CH₃ in aqueous citrate medium of pH 7, to form a blue complex with maximum absorption at 716 nm. The calibration is linear up to 0.12 μg ml⁻¹ calcium with a repeatability (R.S.D.) of 1.0% at a concentration of 0.04 μg ml⁻¹ (n=5). The molar absorptivity of the complex and Sandell’s sensitivity are 3.5×10⁵ l mol⁻¹ cm⁻¹ and 0.11 ng cm⁻², its 10σ limit of quantification and the 3σ limit of detection were found to be 0.3 ng ml⁻¹ and 0.09 ng ml⁻¹ respectively. The influence of reaction variables and the effect of interfering ions are studied; no interference was observed in clinical samples. The proposed method has been applied directly to the determination of calcium in clinical samples without the need for pre-concentration, masking metal ions and digesting samples.     

Rapid and sensitive determination of protein by light-scattering technique with Eriochrome Blue Black R

Based on the interaction between Eriochrome Blue Black R (EBBR) and proteins, which causes a strong light-scattering signal with the maximum scattering peak located at 398 nm, a simple, rapid, sensitive and selective method is developed for the determination of proteins by the light-scattering technique using a common spectrofluoremeter. Under proper experimental conditions, the protein determination can be performed in the range of 0.1-25, 0.1-20 and 0.25-25 μg ml⁻¹ for bovine serum albumin (BSA), human serum albumin (HSA) and human immunoglobulin G (IgG), respectively. The detection limit, calculated as 3 times the S.D. of nine blank measurements, are 33 μg l⁻¹ for BSA, 25 μg l⁻¹ for HSA and 38 μg l⁻¹ for IgG. Moreover, there is no significant difference among the scattering signals yielded by HSA, IgG and BSA, and almost no interference of many amino acids and metal ions. The method has been satisfactorily applied to the direct determination of the total protein in human serum, saliva and urine samples. The results obtained from the studies on the binding characteristics of EBBR to BSA indicated that an electrostatic force existed in the binding system, and the binding constant (K) and the number of the binding sites (n) at 25 °C are 1.69×10⁵ l mol⁻¹ and 0.946, respectively.     

A novel fiber optic spectrophotometric determination of nitrite using Safranin O and cloud point extraction

A novel fiber optic spectrophotometric method for nitrite determination in different samples is suggested, based on the reaction of nitrite with Safranin O in acidic medium to form a diazo-safranin, which is subsequently coupled with pyrogallol in alkaline medium to form a highly stable, red azo dye, followed by cloud point extraction (CPE) using a mixed micelle of a nonionic surfactant, Triton X-114, with an anionic surfactant, sodium dodecyl sulphate (SDS). The reaction and extraction conditions (e.g., acidity for diazotization and alkalinity for pyrogallol coupling, and other reagent concentrations, time, and tolerance to other ions) were optimized. Linearity was obeyed in a concentration range up to 230 μg L⁻¹, and the detection limit of the method is 0.5 μg L⁻¹ of nitrite ion. The molar absorptivity for nitrite of the Safranin-diazonium salt (?_610 nm = 4 × 10³ L mol⁻¹ cm⁻¹) existing in literature was greatly enhanced by pyrogallol coupling and CPE enrichment (?_592 nm = 1.39 × 10⁵ L mol⁻¹ cm⁻¹). The method was applied to the determination of nitrite in tap water, lake water and milk samples with an optimal preconcentration factor of 20.     

2,2′,3,4-Tetrahydroxy-3′-sulpho-5′-nitroazobenzene for spectrophotometric determination of aluminium in pharmaceutical suspensions and granite

A selective and sensitive new spectrophotometric method has been developed for the determination of aluminium. 2,2′,3,4-Tetrahydroxy-3′-sulpho-5′-nitroazobenzene (tetrahydroxyazon SN) formed an orange chelate with aluminium at pH 4. Molar absorptivity of the complex in 1:2 is 5.46 × 10⁴ l mol⁻¹ cm⁻¹ at 479 nm. The method obeys Beer's law in the range of 0.005-1.079 μg ml⁻¹. The determination of aluminium is not interfered with by earth alkaline, alkaline elements, rare earth elements, halides, phosphates, sulphates, urea, ascorbic acid, Sn²⁺, Sr²⁺, Cr³⁺, Cd²⁺, Hg²⁺, or Mn²⁺. The proposed method is rapid and simple, and it has been successfully applied to the determination of aluminium in certified pharmaceutical suspension and granite.     

Spectrofluorimetric determination of human serum albumin using a doxycycline-europium probe

A new spectrofluorimetric method is proposed for determination of human serum albumin (HSA) with the limit of detection at ng levels. Using doxycycline (DC)-europium (Eu³⁺) as a fluorescent probe, in a buffer solution of pH 10.2, HSA can remarkably enhance the fluorescence intensity of the DC-Eu³⁺ complex at 612 nm and the enhanced fluorescence intensity of Eu³⁺ is proportional to the concentration of HSA. Optimum conditions for the determination of HSA are also investigated. The linear ranges for HSA are 0-9.2 and 9.2-34.5 μg ml⁻¹ with limits of detection of 64 and 115 ng ml⁻¹, respectively. This method is simple, practical and relatively free of interference from coexisting substances, as well as much more sensitive than most of the existing assays. The determination results for human serum and urine samples are identical to those by the AOAO method, with relative standard deviations of five determinations of 1.1-3.6%. By the Rosenthal graphic method, the binding number and association constant of human serum albumin with the probe are 1.8 and 3.71×10⁵ l mol⁻¹, respectively.     

Flow injection kinetic spectrophotometric determination of trace amounts of Se(IV) in seawater

A simple, accurate, sensitive and selective flow injection catalytic kinetic spectrophotometric method for rapid determination of trace amounts of selenium is proposed in this paper. The proposed method is based on the accelerating effect of Se(IV) on the reaction of ethexlenediamine tetrecetic acid disodium salt (EDTA) and sodium nitrate with ammonium iron(II) sulfate hexahydrate in acidic media. The absorbance intensity was registered in this reaction solution at 440 nm. The calibration graph is linear in the range of 5 × 10⁻⁹-2 × 10⁻⁷ and 2 × 10⁻⁷-2 × 10⁻⁶ g ml⁻¹. The detection limit is 2 × 10⁻⁹ g ml⁻¹. The relative standard deviation was 3.4% for 5 × 10⁻⁸ g ml⁻¹ Se(IV) (n = 11), 2.7% for 5 × 10⁻⁷ g ml⁻¹ Se(IV) (n = 11). This method is very simple, rapid and suitable for automatic and continuous analysis. The presented system has been applied successfully to determination of Se(IV) of seawater samples.     

Chemiluminescence determination of ultramicro DNA with a flow-injection method

A high sensitive flow-injection chemiluminescence method for determination of calf thymus DNA and herring sperm DNA has been developed. The method is based on the chemiluminescence reaction of Rhodamine B-cerium(IV)-thermally denatured DNAs in sulfuric acid media. The proposed procedure allows quantitation of DNAs in the range 2.6×10⁻⁵ to 0.26 μg ml⁻¹ for calf thymus DNA and 5.0×10⁻⁸ to 5.0×10⁻⁵ μg ml⁻¹ for herring sperm DNA with correlation coefficients 0.9998 and 0.9996 (both n=11), respectively. The detection limits (3σ) are 6.5×10⁻⁶ μg ml⁻¹ for calf thymus DNA and 4.3×10⁻⁸ μg ml⁻¹ for herring sperm DNA. The possible mechanism of chemiluminescence in the system is discussed.     

Flow-injection chemiluminescence assay for ultra-trace determination of DNA using rhodamine B-Ce(IV)-DNA ternary system in sulfuric acid media

A novel flow-injection chemiluminescence method for the determination of DNA at ultra-trace level has been established. In 0.8 M sulfuric acid media, the chemiluminescence of the rhodamine B-cerium (IV) or Ce(IV) system is enhanced by DNA, activated previously by imidazole-HCl buffer solution (pH 7.0). The enhanced intensity of chemiluminescence is in proportion to log DNA concentration 1.0×10⁻⁸ to 0.1 μg ml⁻¹ for herring sperm DNA and 2.0×10⁻⁶ to 0.2 μg ml⁻¹ for calf thymus DNA with 3σ detection limits of 8.3×10⁻⁹ μg ml⁻¹ for herring sperm DNA and 3.5×10⁻⁷ μg ml⁻¹ for calf thymus DNA, respectively. The relative standard deviation for 1.0×10⁻⁴ μg ml⁻¹ herring sperm DNA was 0.99% and 2.0×10⁻³ μg ml⁻¹ for calf thymus DNA was 1.1% (n=11). Using the optimized system, DNA contents in six synthetic samples has been determined with recoveries of 99.5-109.0%. The possible mechanism has also been studied in this paper.     

A rapid spectrophotometric method for the determination of transparent exopolymer particles (TEP) in freshwater

A simple and rapid spectrophotometric method is proposed for the determination of transparent exopolymer particles (TEP) in freshwater samples. In this method, TEP reacts with excess of alcian blue solution yielding a low solubility dye-TEP complex. After centrifugation, the concentration of the remaining dye in the supernatant was determined at 602 nm and its concentration was related to the concentration of TEP in freshwater. The effect of alcian blue concentration from 1.5×10⁻³ to 9.0×10⁻³% (m/v), solution pH from 2.5 to 6.9 and stirring time from 20 to 120 s on the analytical curve was investigated. Under the optimum conditions established, such as alcian blue concentration of 3.0×10⁻³% (m/v); pH of 4.0 (0.2 mol l⁻¹ acetate buffer solution) and stirring time of 1 min, the analytical curve was linear from 0.50 to 10 μg ml⁻¹ (A=0.34−0.037[GX]; r²=0.9999; where A is the absorbance and [GX] the gum xanthan concentration in μg ml⁻¹) with a detection limit of 0.10 μg ml⁻¹. The recovery of TEP (as gum xanthan) for two samples ranged from 95.3 to 108 and the relative standard deviations (R.S.D.s) were lower than 0.8% for gum xanthan solutions at concentrations of 1.0 and 1.5 μg ml⁻¹ (n=8). The results obtained for TEP in freshwater samples using the proposed spectrophotometric method and those obtained using a literature method are in agreement at the 95% confidence level and within an acceptable range of error.     

Spectrophotometric flow-injection analysis of mercury(II) in pharmaceuticals with p-nitrobenzoxosulfamate

A new, simple and rapid spectrophotometric FI method for the accurate and precise determination of Hg(II) in pharmaceutical preparations has been developed. The method is based on the measuring the decrease of absorbance intensity of p-nitrobenzoxosulfamate (NBS) due to the complexation with Hg(II). The absorption peak of the NBS, which is decreased linearly by addition of Hg(II), occurs at 430 nm in 2×10⁻⁴ mol l⁻¹ HNO₃ as a carrier solution. Optimization of chemical and FI variables has been made. A micro column consisting of several packing materials applied instead of reaction coil was also investigated. A background level of Fe(III) maintained in reagent carrier solution with NBS was found useful for sensitivity and selectivity. Under the optimized conditions, the sampling rate was over 100 h⁻¹, the calibration curve obtained were linear over the range 1-10 μg ml⁻¹, the detection limit was lower than 0.2 μg ml⁻¹ for a 20 μl injection volume, and the precision [S_r=1% at 2 μg ml⁻¹ Hg(II) (n=10)] was found quite satisfactory. Application of the method to the analysis of Hg(II) in pharmaceutical preparations resulted a good agreement between the expected and found values.     

A novel spectrofluorimetric method for the ultra trace analysis of nitrite and nitrate in aqueous medium and its application to air, water, soil and forensic samples

A highly sensitive and virtually specific method has been developed for the trace and ultra trace 5 ng ml⁻¹-1 μg ml⁻¹ fluorimetric analysis of nitrite. The method is based on the quenching action of nitrite on the native fluorescence of murexide (ammonium purpurate) [λ_ex=349.0 nm, λ_em=444.5 nm] in the acid range of 0.045-0.315 (M) H₂SO₄. The method is very precise and accurate (S.D.=±0.4877 and R.S.D.=0.4878% for the determination of 0.1 μg ml⁻¹ of nitrite in 11 replicates). Relatively large excesses of over 35 cations and anions do not interfere. The proposed technique has been successfully applied for the determination of nitrite and nitrate in ground water, surface water and sea water, nitrite in soil and nitrate in forensic samples. The method has also been extended for the analysis of NO_x in air.     

Development of integrated chemiluminescence flow sensor for the determination of adrenaline and isoprenaline

A novel integrated chemiluminescence (CL) flow sensor for the determination of adrenaline and isoprenaline is developed based on the enhancing effect of analytes on CL emission of luminol oxidized by periodate in alkaline solution. The analytical reagents luminol and periodate are immobilized on anion exchange resins, respectively, and packed in a glass tube to construct a reagentless sensor. The proposed sensor allows the determination of adrenaline and isoprenaline over the range from 2.0×10⁻⁸ to 1.0×10⁻⁵ g ml⁻¹ and 2.0×10⁻⁷ to 5.0×10⁻⁵ g ml⁻¹, respectively. The detection limits are 7.0×10⁻⁹ g ml⁻¹ for adrenaline and 5.0×10⁻⁸ g ml⁻¹ for isoprenaline with a relative standard deviation of 1.7% for the 1.0×10⁻⁷ g ml⁻¹ adrenaline (n=11) and 2.1% for 1.0×10⁻⁶ g ml⁻¹ isoprenaline (n=11). The sample throughput was 60 samples h⁻¹. The sensor has been successfully applied to the determination of adrenaline and isoprenaline in pharmaceutical preparations.     

Flow-injection chemiluminescence determination of aminomethylbenzoic acid and aminophylline based on N-bromosuccinimide-luminol reaction

A novel and sensitive chemiluminescence (CL) method for the determination of aminomethylbenzoic acid and aminophylline coupled with flow-injection analysis (FIA) technique is developed in this paper. It is based on the inhibition effect of the studied drugs on the chemiluminescence emission of N-bromosuccinimide-luminol (NBS-luminol) system. Under the optimum conditions, the decreased CL intensity is linear with the concentration of aminomethylbenzoic acid in the range of 2×10⁻⁸ to 1.0×10⁻⁶ g ml⁻¹ and with the concentration of aminophylline in the range of 1×10⁻⁷ to 7.0×10⁻⁶ g ml⁻¹, respectively. The detection limit is 7.0×10⁻⁹ g ml⁻¹ for aminomethylbenzoic acid (3σ) and 3.4×10⁻⁸ g ml⁻¹ for aminophylline (3σ). The relative standard deviations (R.S.D.) for 11 parallel measurements of 2.0×10⁻⁷ g ml⁻¹ aminomethylbenzoic acid and 1.0×10⁻⁶ g ml⁻¹ aminophylline are 2.6 and 3.0%, respectively. The proposed methods have been applied for the determination of the studied drugs in their pharmaceutical formulations with satisfactory results. The possible use of the proposed system for the determination of aminomethylbenzoic acid in plasma sample was also tested. The possible inhibition mechanism of aminomethylbenzoic acid and aminophylline on luminol-NBS system was discussed briefly.     

Determination of palladium in various samples by atomic absorption spectrometry after preconcentration with dimethylglyoxime on silica gel

A preconcentration method based on the adsorption of palladium-dimethylglyoxime (DMG) complex on silica gel for the determination of palladium at trace levels by atomic absorption spectrometry (AAS) has been developed. The retained palladium as Pd(DMG)₂ complex was eluted with 1 mol l⁻¹ HCl in acetone. The effect of some analytical parameters such as pH, amount of reagent and the sample volume on the recovery of palladium was examined in synthetic solutions containing street dust matrix. The influence of some matrix ions on the recovery of palladium was investigated by using the developed method when the elements were present both individually and together. The results showed that 2500 μg ml⁻¹ Na⁺, K⁺, Mg²⁺, Al³⁺ and Fe³⁺; 5000 μg ml⁻¹ Ca²⁺ ; 500 μg ml⁻¹ Pb²⁺; 125 μg ml⁻¹ Zn²⁺; 50 μg ml⁻¹ Cu²⁺ and 25 μg ml⁻¹ Ni²⁺ did not interfere with the palladium signal. At the optimum conditions determined experimentally, the recovery for palladium was found to be 95.3±1.2% at the 95% confidence level. The relative standard deviation and limit of detection (3s/b) of the method were found to be 1.7% and 1.2 μg l⁻¹, respectively. In order to determine the adsorption behaviour of silica gel, the adsorption isotherm of palladium was studied and the binding equilibrium constant and adsorption capacity were calculated to be 0.38 l mg⁻¹ and 4.06 mg g⁻¹, respectively. The determination of palladium in various samples was performed by using both flame AAS and graphite furnace AAS. The proposed method was successfully applied for the determination of palladium in the street dust, anode slime, rock and catalytic converter samples.     

Sensitive and selective determination of molybdenum by flow injection chemiluminescence method combined with controlled potential electrolysis technique

A sensitive and selective flow injection chemiluminescence (CL) method combined with controlled potential electrolysis technique was described for the determination of molybdenum. The method is based on the chemiluminescence reaction of luminol with unstable molybdenum(III) in alkaline solution. The molybdenum(III) was on-line reduced from molybdenum(VI) via controlled potential electrolysis technique using a homemade flow-through carbon electrolytic cell at the potential of −0.6 V (versus Ag/AgCl). The method allows the determination of molybdenum in the 5.0×10⁻¹⁰ to 5.0×10⁻⁷ g ml⁻¹ range with a limit of detection (3σ) of 5×10⁻¹¹ g ml⁻¹ molybdenum. The relative standard deviation is 2.6% for the 1.0×10⁻⁹ g ml⁻¹ molybdenum solution in 11 repeated measurements. This method was successfully applied to the determination of molybdenum in water samples.     

Synchronous fluorescence determination of protein with functionalized CdS nanoparticles as a fluorescence probe

Nanometer-sized fluorescent particles have been successfully synthesized. A synchronous fluorescence method, with high sensitivity and selectivity, has been developed for rapid determination of protein with functionalized CdS as a fluorescence probe. When Δλ=260 nm, maximum synchronous fluorescence is produced at 274 nm at pH 7.0. Under optimal conditions, the calibration graphs are linear over the range 0.1-3.0 μg ml⁻¹ for bovine serum albumin (BSA), 0.1-11.0 μg ml⁻¹ for γ-globulin (γ-G) and 0.1-1.4 μg ml⁻¹ for human serum albumin (HSA), respectively. Limits of determination were 0.01 μg ml⁻¹ for BSA, 0.019 μg ml⁻¹ for γ-G and 0.021 μg ml⁻¹ for HSA, respectively. The relative standard deviations of seven replicate measurements were 1.8% for 1.0 μg ml⁻¹ BSA, 2.2% for 1.0 μg ml⁻¹ γ-G and 2.3% for 1.0 μg ml⁻¹ HSA.     

Simultaneous determination of 11 drugs belonging to four different groups in human urine samples by reversed-phase high-performance liquid chromatography method

A new, accurate, sensitive and fast reversed-phase high-performance liquid chromatography (RP-HPLC) as an analytical method for the quantitative determination of 11 drugs in human urine was worked out, optimized and validated. The objects of analysis were imipenem (IMP), paracetamol (PAR), dipyrone (DPR), vancomycin (VCM), amikacin (AMK), fluconazole (FZ), cefazolin (CFZ), prednisolone (PRE), dexamethasone (DEX), furosemide (FUR) and ketoprofen (KET) belonging to four different groups (antibiotics, analgesic, demulcent and diuretic). For HPLC analysis, diode array (DAD) and fluorescence (FL) detectors were used. The separation of analyzed compounds was conducted by means of a LiChroCART^® Purospher^® C₁₈e (125 mm × 3 mm, particle size 5 μm) analytical column with LiChroCART^® LiChrospher^® C₁₈ (4 mm × 4 mm, particle size 5 μm) pre-column with gradient elution. Analyzed drugs were determined within 20 min. The mobile phase was comprised of various proportions of methanol, acetonitrile and 0.05% trifluoroacetic acid in water. AMK was separated and determined from human urine using ortho-phthaldialdehyde-3-mercaptopropionic acid (OPA-3-MPA) as a fluorescent reagent by RP-HPLC-FL. The following retention times for drugs IMP, PAR, DPR, VCM, AMK, FZ, CFZ, PRE, DEX, FUR and KET in human urine were found: 4.01 min, 4.86 min, 6.71 min, 8.14 min, 9.46 min, 10.01 min, 10.90 min, 13.34 min, 14.06 min, 16.03 min and 18.98 min, respectively. Excellent linearity was obtained for compounds in the range of concentration: 0.35-42 μg ml⁻¹, 0.5-45 μg ml⁻¹, 4.5-38 μg ml⁻¹, 0.25-25 μg ml⁻¹, 0.5-35 μg ml⁻¹, 0.25-22 μg ml⁻¹, 0.03-52 μg ml⁻¹, 0.15-25 μg ml⁻¹, 0.25-28 μg ml⁻¹, 0.05-18 μg ml⁻¹ and 0.15-35 μg ml⁻¹ for IMP, PAR, DPR, VCM, AMK, FZ, CFZ, PRE, DEX, FUR and KET, respectively. The limits of detection (LOD) and limits of quantification (LOQ) for analyzed drugs were calculated in all cases and recovery studies were also performed. Ten human urine samples obtained from patients treated in hospital have been tested. In analyzed samples, one or more drugs from the 11 examined drugs were detected. The concentrations of examined drugs in urine samples ranged between: 1.5-12 μg ml⁻¹ of PAR, 5.2-11.5 μg ml⁻¹ of DPR, 0.13-9.5 μg ml⁻¹ of CFZ and 0.1-8 μg ml⁻¹ of FUR. This method can be successfully applied to routine determination of all these drugs in human urine samples.     

Ultra-trace level determination of hydroquinone in waste photographic solutions by UV-vis spectrophotometry

A simpler UV-vis spectrophotometric method was investigated for hydroquinone (HQ) determination using KMnO₄ as oxidizing agent for conversion of HQ to p-benzoquinone (BQ) as well as signal enhancer. Various parameters such as analytical wavelength, stability time, temperature, pH, solvent effect and interference of chemicals were checked and parameters optimized by using 1 μg ml⁻¹ standard solution of HQ. Beer's Law was applicable in the range of 0.07-2 μg ml⁻¹ and 0.005-0.05 μg ml⁻¹ at 245.5 nm and at 262 nm for aqueous standard solutions of HQ with linear regression coefficient value of 0.9978 and 0.9843 and detection limit of 0.021 μg ml⁻¹ and 0.0016 μg ml⁻¹ HQ, respectively. Standard deviation of 1.7% and 2.4% was true for 1 μg ml⁻¹ and 0.03 μg ml⁻¹ HQ solution (n = 11) run at respective wavelengths. The method was successfully applied to dilute waste photographic developer samples for free HQ determination.     

Functionalized semiconductor nanocrystals for ultrasensitive detection of peptides

Semiconductor CdS nanoparticle have been prepared and modified with thiovanic acid. The functionalized nanoparticles are water-soluble. They were used as the fluorescence probes in the ultrasensitive detection of peptides. This method is based on the fluorescence enhancement of functionalized nano-CdS in the presence of peptide with mercapto groups (GN-9) and the fluorescence quenching of functionalized nano-CdS in the presence of peptide (GA-8 and MT-25). Excitation and emission wavelengths were 360 and 530 nm, respectively. Under optimum conditions, the calibration graphs are linear over the range of 0.15-3.5, 0.2-4.0, and 0.2-3.8 μg ml⁻¹ for GN-9, GA-8 and MT-25, respectively. The corresponding detection limits were 0.010 μg ml⁻¹ for GN-9, 0.018 μg ml⁻¹ for GA-8 and 0.022 μg ml⁻¹ for MT-25, respectively. This method has been proved to be a simple, rapid and sensitive method.