离子交换色谱-氢化物发生原子荧光法测定水产品中硒的形态

建立了利用离子交换色谱-原子荧光联用技术同时测定水产品中3种硒形态的方法,研究了仪器的工作条件、载流、KBH4浓度对硒荧光信号值的影响。采用Hamilton PRP X-100色谱柱(250×4.1 mm,10μm),以30 mmol/L NH4H2PO4为流动相,可以在10 min内同时分离、检测了硒代胱氨酸SeCys、硒代蛋氨酸SeMet和Se(Ⅳ)。当3种形态的质量浓度范围为0~80μg/L时,各形态均得到良好的线性关系,线性相关系数均大于0.9990,各形态的检出限分别为SeCys 1.66μg/L,SeMet 0.91μg/L,Se(Ⅳ)1.10μg/L,相对标准偏差RSD均小于5%(n=11)。在最佳条件下,应用该方法测定了水产品中的硒形态,3种硒形态化合物加标回收率在87.3%~102.6%之间。方法可满足水产品中硒形态的定量分析。     

液相色谱-双通道原子荧光检测联用法同时测定砷和硒的形态

建立了一种利用高效液相色谱-双通道原子荧光检测联用同时进行砷和硒形态分析的方法。以10 mmol/L NH4H2PO4溶液(pH 5.6)(添加2.5%(体积分数)的甲醇)为流动相,在12 min内同时分离了三价砷(As(III))、一甲基砷(MMA)、二甲基砷(DMA)、五价砷(As(V))、硒代胱氨酸(SeCys)、硒代蛋氨酸(SeMet)和四价硒［Se(IV)］等化合物。As(III)、DMA、MMA、As(V)、SeCys、SeMet和Se(IV)的检出限分别为1,3,2,3,4,18和3 μg/L (进样量为200 μL),5次测定的相对标准偏差为1.9%～6.1%(As 100 μg/L, Se 300 μg/L)。应用该方法对人体尿样及硒酵母片中砷和硒的形态进行了分析,目标物在尿样中的加标回收率为83%～108%,在硒酵母片中的加标回收率为88%～105%。实验结果表明,该方法可用于尿样及药品中砷和硒形态的日常分析。该方法减少了样品的分析时间和试剂用量,降低了工作强度,提高了工作效率。     

高效液相色谱-电感耦合等离子体质谱法测定人尿中硒形态

采用高效液相色谱-电感耦合等离子体质谱法(HPLC-ICP/MS)测定人尿中硒代胱氨酸(SeCys_2)、甲基硒代半胱氨酸(MeSeCys)、亚硒酸盐[Se(Ⅳ)]、硒代蛋氨酸(SeMet)、硒酸盐[Se(Ⅵ)]5种硒形态。样品经超纯水稀释后,采用Hamilton PRP-X100色谱柱(250 mm×4 mm,10μm)分离,以40 mmol/L磷酸氢二铵(含1%甲醇,pH 5)为流动相进行等度洗脱,13 min内可将5种硒形态分离。5种硒形态的线性范围为0～300.0μg/L,相关系数(r)均大于0.999,检出限为0.2～0.5μg/L。除SeCys_2的加标回收率为37.7%～70.4%外,MeSeCys、Se(Ⅳ)、SeMet、Se(Ⅵ)的加标回收率为80.0%～123%;5种硒形态的相对标准偏差(RSD)均不大于7.8%。应用该方法测定实际样品,结果显示人尿中硒形态主要以SeCys_2为主,同时含有少量MeSeCys、SeMet、无机硒及未知含硒化合物。     

AE-HG-AFS测定长期汞暴露人群补硒后尿中硒的形态

建立了一种利用阴离子交换高效液相色谱与氢化物发生原子荧光光谱联用同时测定四、六价硒及硒代半胱氨酸(SeCys)形态的方法。优化了六价硒的还原条件及仪器检测参数,以不同浓度的柠檬酸铵作为流动相,在10 min内同时分离了四、六价硒及硒代半胱氨酸(SeCys)。采用加标法定量,加标回收率在90%～119%之间,相对标准偏差为1.6%～3.1%(100μg/L),四、六价硒及硒代半胱氨酸(SeCys)的检出限分别为0.32μg/L、0.47μg/L和0.44μg/L(进样量为100μL)。应用该法对长期汞暴露人群补硒后尿中的小分子硒的形态进行了分析,仅检测到硒代半胱氨酸(SeCys)。     

HPLC-DRC-ICP-MS测定富硒蔬菜中的硒形态

建立了高效液相色谱-动态反应池-电感耦合等离子体质谱(HPLC-DRC-ICP-MS)联用测定硒代胱氨酸(SeCys2)、甲基硒代半光氨酸(MeSeCys)、亚硒酸盐(SeIV)、硒代蛋氨酸(SeMet)和硒酸盐(SeVI)的方法。样品通过胃蛋白酶提取,采用Hamilton PRP X-100色谱柱(250 mm×4.6 mm,10μm),使用5 mmol/L的柠檬酸溶液(pH 4.7)作为流动相,在10 min内可以完全分离5种硒形态。在80Se质量数下,采用甲烷作为DRC反应气,可有效消除40Ar40Ar+对80Se的干扰,提高检测灵敏度。电感耦合等离子体质谱(ICP-MS)检测,各硒形态的线性相关系数均大于0.9990,Se(IV)、Se(VI)、SeMet、SeCys2、MeSeCys的定量限分别为5,10,10,5,5μg/kg,5种硒形态的加标回收率在80.1%～99.2%之间,可满足蔬菜中硒形态定量分析。     

高效液相色谱-电感耦合等离子体质谱法同时测定食品中7种硒形态

采用高效液相色谱-电感耦合等离子体质谱(HPLC-ICP-MS)联用技术同时测定食品中7种硒形态。样品均质后先用水超声萃取2 h,离心分离后,采用ZORBAX SB-Aq C_(18)色谱柱(250 mm×4.6 mm,5μm),以20 mmol/L柠檬酸+5 mmol/L已烷磺酸钠(pH=4.4)为流动相等度洗脱,Se(Ⅳ)、Se(Ⅵ)、硒代胱氨酸(SeCys2)、甲基硒代半胱氨酸(SeMeCys)、硒脲(SeUr)、硒代蛋氨酸(SeMet)、硒代乙硫氨酸(SeEt)7种硒形态在10 min内达到完全分离。7种硒形态化合物的质量浓度在2.5～100.0μg/L范围内与峰面积呈线性关系,检测限(S/N=3)为0.005 mg/kg。加标回收率在71.9%～116.7%之间,相对标准偏差(n=6)在1.62%～18.48%之间。该方法精密度及准确度高,重现性好,适用于食品中上述7种硒形态化合物的同时快速测定。     

微波辅助萃取-液质联用技术测底泥砷、硒的化学形态

建立了用反相离子对色谱和电感耦合等离子体质谱的联用技术同时测定As（Ⅲ）、 As（Ⅴ）、 MMA、 DMA、 Se（Ⅳ）、 Se（Ⅵ）、 SeMet和SeCys的砷、硒化学形态分析方法. 分别从流动相pH值、离子对试剂的浓度、甲醇量和流速4个方面进行了分离测定条件的优化. 利用碰撞池技术（CCT）较好地解决了^40Ar^35Cl^＋复合离子对^75As的干扰, 并使^80Se的测定成为可能, 有效地提高了灵敏度. 将该方法应用于上海市苏州河底泥样品的微波辅助萃取液的形态分析中, 砷和硒的检出限分别达到0.4～1.3 和0.5～1.9 μg/L.     

共价氢化物发生-光度分析法高选择性的研究与应用——Ⅰ.锗、砷、硒共价氢化物性质初探及其分别测定时其它氢化物干扰的消除

本文采用氢化物发生-银溶胶光度分析法探讨了GeH_4、AsH_3和H_2Se的性质,并利用共价氢化物气体分离柱分别建立了测定锗、砷时消除其它可生成氢化物元素干扰的简便、高效方法。测定1.0μg Ge(Ⅳ),5000μg As(Ⅴ)、Bi(Ⅱ)、Pb(Ⅰ)、1000μg Sb(Ⅱ)、Sn(Ⅰ)、500μg As(Ⅱ)和100μg Se(Ⅳ)、Sn(Ⅳ),Te(Ⅳ)不产生干扰。对砷的测定,其它共价氢化物元素的允许倍数分别为:Sb(Ⅱ)(5000)、Pb(Ⅰ)(5000)、Bi(Ⅱ)(5000)、Sn(Ⅰ)(1000)、Se(Ⅳ)(100)、Te(Ⅳ)(100)和Ge(Ⅳ)(15)。     

高效液相色谱-电感耦合等离子体质谱联用检测食品中的五种硒形态

建立了高效液相色谱-电感耦合等离子体质谱(HPLC-ICP-MS)联用检测硒酸盐(SeVI)、亚硒酸盐(SeIV)、硒代蛋氨酸(SeMet)、硒代胱氨酸(SeCys2)和硒代乙硫氨酸(SeEt)的方法。采用Hamilton PRP X-100色谱柱（250 mm×4.6 mm, 5 μm）,使用5 mmol/L的柠檬酸溶液(pH 4.5)作为流动相,电感耦合等离子体质谱(ICP-MS)检测,在21 min内可以完全分离5种硒形态。各形态硒的线性相关系数均大于0.9995, SeVI、SeIV、SeMet、SeCys2、SeEt的检出限分别为0.4、0.4、5.6、0.9、1.2 μg/L。探讨了不同提取方法的提取效果,鲜蘑菇和猪肉样品加标回收实验表明,对水溶性良好的无机硒和硒代蛋氨酸而言,采用柠檬酸溶液提取的效果非常好,SeIV和SeVI的回收率均在100%左右,SeMet的回收率为85.0%～95.3%;用蛋白酶水解提取,SeCys2和SeEt的回收率为79.9%～91.5%。该方法可完全满足食品中这5种硒形态的准确定量分析。     

HPLC–AFS联用测定海产品中砷的形态

建立了高效液相色谱–原子荧光分光光度法测定海产品中无机砷(As V,AsⅢ)、有机砷(DMA,MMA,AsB)含量的方法。样品经含10%(体积分数)HCl的提取液振荡提取、离心分离、二路形态分析预处理、高效液相色谱分离,用原子荧光光度计检测As(Ⅲ),DMA,MMA,As(V);四路条件(过氧化氢氧化和开启紫外灯)形态分析预处理装置处理,高效液相色谱分离,原子荧光光度计测定AsB。As(Ⅲ)线性范围为0～100.00μg/L,r2=0.999 7;DMA线性范围为0～100.00μg/L,r2=0.999 3;MMA线性范围为0～100.00μg/L,r2=0.999 0;As(V)线性范围为0～100.00μg/L,r2=0.999 1;AsB线性范围为0～200.00μg/L,r2=0.999 4。3个样品加标回收率为As(Ⅲ)86.7%～89.4%,DMA 111.2%～117.0%,MMA 109.7%～111.6%,As(V)83.8%～90.7%,AsB 88.3%～90.4%。用该方法测定虾仁(干)5个价态测定结果的相对标准偏差为3.07%～9.93%(n=6)。5个价态的检出限(S/N=2)为As(Ⅲ)0.29μg/L,DMA 0.36μg/L,MMA 0.27μg/L,As(V)0.56μg/L,AsB 1.46μg/L。该方法适用于海产品中As(Ⅲ),DMA,MMA,As(V),AsB含量的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.