Composite electrolytes based on poly(ethylene oxide) and binary ionic liquids for dye-sensitized solar cells

The sunlight is the largest single available source of clean and renewable energy to ensure human society’s sustainable development. Owing to their low production cost and high energy conversion efficiency, dye-sensitized solar cells (DSSCs) have been regarded as good alternatives to conventional photovoltaic devices. Herein, a series of composite electrolytes based on poly(ethylene oxide) (PEO) and the binary ionic liquids 1-propyl-3-methy-imidazolium iodide ([PMIm]I) and 1-ethyl-3-methylimidazolium thiocyanate ([EMIm][SCN]) were prepared and then applied to fabricate six DSSCs. The composite electrolytes were characterized by fourier transform infrared spectroscopy (FTIS), X-ray diffraction (XRD), and electrochemical impedance spectra (EIS). It was shown that the addition of binary ionic liquids would reduce the degree of crystallinity of PEO, thus improving the ionic conductivities of the electrolytes by about 2 orders of magnitude. Investigation on the photovoltaic performances of these DSSCs showed that the fill factor (FF) could reach up to 0.67 and energy conversion efficiency (η) could reach up to 4.04% under AM 1.5 full sunlight (100 mW/cm2).     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

Quasi-solid-state dye-sensitized solar cell based on a polymer gel electrolyte with in situ synthesized ionic conductors

A polymer gel electrolyte with in situ synthesized Acac-Py-I₂ ionic conductors was prepared for fabricating a quasi-solid-state dye-sensitized solar cell (QS-DSSC). The in situ synthesized Acac-Py-I₂ ionic conductors show weaker influence on the liquid electrolyte absorbency of the polymer gel electrolyte than that of Acac-Py-I₂ ionic conductors dissolved in liquid electrolyte. Owing to the higher liquid electrolyte absorbency, the polymer gel electrolyte with in situ synthesized Acac-Py-I₂ ionic conductors shows higher ionic conductivity than that of polymer gel electrolyte with Acac-Py-I₂ ionic conductors absorbed from liquid electrolyte. QS-DSSC containing the polymer gel electrolyte with in situ synthesized Acac-Py-I₂ ionic conductors shows 3.815% energy conversion efficiency, which is 21.6% higher than that of QS-DSSC containing polymer gel electrolyte with Acac-Py-I₂ ionic conductors absorbed from liquid electrolyte.     

Synthesis of organic sulfobetaine‐based polymer gel electrolyte for dye‐sensitized solar cell application

We have synthesized eco‐friendly, economic, and equally efficient polysulfobetaine‐based gel electrolyte to the alternative of liquid electrolyte in the fabrication of dye‐sensitized solar cells (DSSCs) for the first time. This nitrogen‐rich and highly conductive polysulfobetaine was synthesized by an easy and facile method without the use of any catalyst and explored for its DSSC application. The synthesized polymer gel electrolyte exhibited good ionic conductivity about 6.8 × 10^?3 Scm^?1 at ambient temperatures. DSSCs were fabricated based on this polysulfobetaine gel electrolyte and studied for their performance based on photovoltaic parameters. The DSSC photovoltaic results were appreciable and are Voc = 0.82 V, Jsc = 11.49 mA/cm², FF = 66%, and PCE = 6.26% at 1 sun intensity. These values are slightly lower than conventional liquid electrolyte‐based DSSC shown as Voc = 0.78 V, Jsc = 12.90 mA/cm², FF = 69%, and PCE = 7.07%, both at 100 mWcm^?2. Conductivity and photovoltaic parameters of the device reveals that as prepared polysulfobetaine‐based polymer gel electrolyte may be useful in the fabrication of DSSC and other electrochemical devices. Copyright © 2017 John Wiley & Sons, Ltd.     

A novel gel polymer electrolyte based on poly ionic liquid 1-ethyl 3-(2-methacryloyloxy ethyl) imidazolium iodide

Poly ionic liquid 1-ethyl 3-(2-methacryloyloxy ethyl) imidazolium iodide (PEMEImI) as a single-ion conductor was designed and synthesized. When appropriate amount of suitable plasticizers, I₂ and polyacrylonitrile (PAN) were incorporated into it, the complex formed gel polymer electrolyte. Chemical structure, thermal behavior and ionic conductive properties of the gel polymer electrolyte were investigated by Raman spectra, UV-Vis spectra, differential scanning calorimetry (DSC), and complex impedance analysis, respectively. For the new gel polymer electrolyte, the ionic conductivity of about 1 × 10⁻³ S cm⁻¹ at room temperature was achieved.     

Gelation of a liquid electrolyte with aniline for use in a quasi-solid-state dye-sensitized solar cell

A new kind of gel electrolyte containing only organic solvents and an iodide salt-namely 3-methoxypropionitrile(MPN),aniline and AlI 3 -has been prepared.Gel formation results from the Lewis acid-base interaction between the Lewis acid ionic conductor AlI 3 and the Lewis base organic solvent aniline and no additional gelling agent is required.The AlI 3-aniline complex acts both as an ionic conductor and as a gelling agent.The differences between the peaks characteristic of the-NH 2 group and aromatic ring in the FTIR spectra of free aniline and the AlI 3-aniline hybrid confirm the formation of the AlI 3-aniline complex.The photovoltaic performance and long-term stability of dye-sensitized solar cells can be greatly enhanced by the addition of aniline to the AlI 3-MPN liquid electrolyte.     

一种不含胶凝剂的凝胶电解质在准固态染料敏化太阳能电池中的应用

报道了一种不含胶凝剂的凝胶电解质的制备及在准固态染料敏化太阳能电池中的应用.这种新型凝胶电解质仅含有机溶剂和碘盐,即3-甲氧基丙腈、苯胺、三碘化铝和碘.上述混合物通过路易斯酸性三碘化铝离子导体和路易斯碱性苯胺有机溶剂间的路易斯酸-碱相互作用形成凝胶,无需额外添加传统凝胶电解质的关键组分—胶凝剂.形成的三碘化铝-苯胺复合物在凝胶电解质中能同时发挥离子导体和胶凝剂的作用.红外光谱图中苯胺的氨基和苯环特征峰的变化证实了三碘化铝-苯胺复合物的形成.含这种新型凝胶电解质的准固态染料敏化太阳能电池光电性能和稳定性与含三碘化铝-3-甲氧基丙腈液体电解质的染料敏化太阳能电池相比有很大提高.     

Interaction mechanism of a novel polymer electrolyte composed of poly(acrylonitrile), lithium triflate,and mineral clay

The addition of optimum cetyl pyridium chloride (CPC)–modified montmorillonite (CM) increases the ionic conductivity of poly(acrylonitrile)‐based electrolytes by roughly two orders of magnitude. Specific interactions between the silicate layer, the nitrile group, and the lithium cation were investigated by FTIR, solid‐state NMR, dielectric analyzer, and alternating current impedance. IR and NMR spectra confirm that the negative charges in the silicate layers alter the ionic charge environment of the PAN‐based electrolyte composites, which have the same function as the polar group in PAN. The optimum CM content to achieve the maximum ionic conductivity is 6 phr. However, untreated montmorillonite leads to insignificant polymer intercalation, the negative charges in the silicate layers fail to appreciably disturb the attractive force of the lithium salt, and the resulting conductivity improvement is also less than that of the CM additives. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2407–2419, 2001     

Novel photosensitizer for dye-sensitized solar cell based on ionic liquid–doped blend polymer electrolyte

The existing energy situation demands not only the huge energy in a short time but also clean energy. In this regard, an integrated photo-supercapacitor device has been fabricated in which photoelectric conversion and energy storage are achieved simultaneously. A novel carbazole-based dye is synthesized and characterized for photosensitizer. The silver-doped titanium dioxide (Ag-TiO₂) is synthesized, and it is used as photoanode material. Different concentrations of tetrabutylammonium iodide (TBAI)-doped polyvinyl alcohol–polyvinylpyrrolidone (PVA-PVP) blend polymer electrolytes are prepared, and their conductivity and dielectric properties were studied. Reduced graphene oxide (r-GO) is synthesized by a one-pot synthesis method and confirmed using Raman spectroscopy for counter electrode material in dye-sensitized solar cell (DSSC) and supercapacitor electrodes. The DSSC having 4% Ag-TiO₂–based photoanode showed the highest efficiency of 1.06% (among r-GO counter electrodes) and 2.37% (among platinum counter electrodes). The supercapacitor before integration and after integration exhibits specific capacitance of 1.72 Fg⁻¹ and 1.327 Fg⁻¹, respectively.

Graphical Abstract

     

TiO2/SnO2复合空心球在染料敏化太阳能电池中的应用

采用模板辅助法制备了SnO2/TiO2复合空心球,样品直径为1.5~4.0μm,比表面积达到了92.9 m^2·g^-1,复合空心球表现出优越的光散射性能.以这种复合空心球作为染料敏化太阳能电池的光阳极,电池的光电转换效率可达到7.72%,高于SnO2微米球(2.70%)和TiO2微米球(6.26%).此外,以锐钛矿型TiO2纳米晶作为底层,SnO2/TiO2复合空心球作为光散射层制备的双层结构光阳极,电池光电转换效率进一步提升至8.43%.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and modified montmorillonite

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer, which is superior to poly(ethylene oxide) in mechanical stability due to its cross-linked structure, modified montmorillonite (MMMT) and LiClO₄, and CGPE with good mechanical strength comprises of the CSPE and LiClO₄–PC (propylene carbonate) solution. The ionic conductivity can be enhanced after the addition of MMMT, and CGPE exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature. The temperature dependence of the ionic conductivity of the CSPE follows the Vogel–Tamman–Fulcher (VTF) equation. The effects of MMMT on the interactions in these systems and the possible conduction mechanisms are also discussed.     

Theoretical study of quinolines-I(2) intermolecular interaction and implications on dye-sensitized solar cell performance

The monomer and intermolecular charge-transfer complexes of 13 different quinoline derivatives with diiodine were studied using ab initio molecular orbital (MO) and density functional theory (DFT) methods. Calculations revealed that the sigma* orbital of iodine interacts with the nitrogen lone pair in the quinoline ring. The open-circuit photovoltage (V(oc)) values of an Ru(II) complex dye-sensitized nanocrystalline TiO(2) solar cell with an I(-)/I(3) (-) redox electrolyte in acetonitrile using quinoline additives were compared to the computational calculations on the intermolecular interaction between quinolines and I(2). The optimized geometries, frequency analyses, Mulliken population analyses, natural bond orbital (NBO) analyses, and interaction energies indicate that the V(oc) value of the solar cell is higher when quinoline complexes more favorably interact with I(2). Therefore, the interaction between the quinoline additives and iodine redox electrolyte is an important factor for controlling dye-sensitized solar cell performance.     

Influence of light scattering particles in the TiO2 photoelectrode for solid-state dye-sensitized solar cell

A TiO₂ film was modified by adding light scattering particles and applied to an anode electrode in solid-state dye-sensitized solar cells (DSSCs). The TiO₂ films with 10 wt% (vs. TiO₂ weight) light scattering particles showed enhanced performance (28%), compared with nanocrystalline TiO₂ films, which were used as the controls. In particular, the photocurrent density (J_sc) reached approximately 12.6 mA/cm² under a one-sun condition. This was attributed to the light scattering effect and decrease in internal resistance through the macroporous structure with a minor loss of electron transport. However, in the case of a larger concentration of light scattering particles (>10 wt%), there was a decrease in the efficiency of DSSCs, which resulted from the decreased surface area and degraded electron transport and charge recombination properties, as confirmed by the measurement of stepped light-induced photocurrent and photovoltage transients. Furthermore, the diffusion properties and kinetics of the composite polymer electrolyte with the nanoporous and macroporous TiO₂ films were compared and evaluated from the electrochemical impedance spectra.     

Dielectric relaxation and conductivity studies on (PEO:LiClO4) polymer electrolyte with added ionic liquid [BMIM][PF6]: Evidence of ion–ion interaction

Polymer electrolytes, (PEO:LiClO₄)+x IL (1‐Buty‐3‐methylimidazolium hexafluorophosphate) with varying concentration of IL; x = 0,5,10,15,20 wt % have been prepared by solution cast technique and characterized by X‐Ray diffraction, differential scanning calorimetery, FTIR, conductivity and dielectric relaxation measurements in the frequency range of 100 Hz–5 MHz. Temperature dependence of relaxation frequency and conductivity were found to be typical of thermally activated process both at T > T_m and T < T_m. Composition dependence of conductivity, dielectric relaxation, and degree of crystallinity has also been studied. On addition of IL, the degree of crystallinity after a decrease at 5 wt % IL increases slightly at 10 wt % and then finally decreasing. Variation of conductivity and relaxation frequency with composition could only be partly explained on the basis of variation of degree of crystallinity. An additional feature of ion–ion interaction (contact ion pair formation between IL or salt cations and their associated anions) has been invoked which was supported by FTIR studies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Solid polymer electrolytes I,preparation, characterization,and ionic conductivity of gelled polymer electrolytes based on novel crosslinked siloxane/poly(ethylene glycol) polymers

A series of crosslinked siloxane/poly(ethylene glycol) (Si–PEG) copolymers were synthesized from the reactive methoxy‐functional silicone resin (Si resin) and PEGs with different molecular weights via two kinds of crosslinking reactions during an in situ curing stage. One of the crosslinking reactions is the self‐condensation between two methoxy groups in the Si resin, and another one is an alkoxy‐exchange reaction between the methoxy group in the Si resin and the OH group in PEG. The synthesized crosslinked copolymers were characterized by Fourier transform infrared spectroscopy, DSC, and ¹³C NMR. The crosslinked copolymers were stable in a moisture‐free environment, but the Si? O? C linkages were hydrolyzed in humid conditions. The gel‐like solid polymer electrolytes (SPEs) were prepared by impregnating these crosslinked Si–PEG copolymers in a propylene carbonate (LiClO₄/PC) solution. The highest conductivity reached 2.4 × 10^?4 S cm^?1 at 25 °C and increased to 8.7 × 10^?4 S cm^?1 at 85 °C. The conductivities of these gel‐type SPEs were affected by the content of LiClO₄/PC, the molecular weights of PEGs, and the weight fraction of the Si resin. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2051–2059, 2004     

A new composite polymer electrolyte based on poly(ethyleneoxide)/ polysiloxane/BMImTFSI/organomontmorillonite

Composite polymer electrolytes based on poly(ethylene oxide)-polysiloxane/l-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide/organomontmorillonite(PEO-PDMS/1L/OMMT) were prepared and characterized.Addition of both an ionic liquid and OMMT to the polymer base of PEO-PDMS resulted in an increase in ionic conductivity.At room temperature,the ionic conductivity of sample PPB100-OMMT4 was 2.19×10~3 S/cm.The composite polymer electrolyte also exhibited high thermal and electrochemical stability and may potentially be applied in lithium batteries.     

Effects of ethylene glycol dimethacrylate as cross-linker in ionic liquid gel polymer electrolyte based on poly(glycidyl methacrylate)

In this study, modified poly(glycidyl methacrylate)-based films for gel electrolyte were prepared by an in situ UV photopolymerization technique. The effects of adding ethylene glycol dimethacrylate (EGDMA) to the polymer host were studied through X-ray diffraction analysis and differential scanning calorimetry. The results from Fourier transform-infrared spectra indicate complete polymerization among the monomers. The addition of EGDMA to the formulation of gel polymer electrolyte increased the loading of 1-butyl-3-methylimidazolium bis(fluoromethylsulfonyl)imide up to 200 wt.% with the highest value of 8.2 × 10^?4 S cm^?1. All the gel polymer electrolyte membranes obeyed the Arrhenius law.     

Synthesis and properties of all solid polymer electrolytes based on poly(vinyl acetate‐co‐acetyl ethylene oxide acrylate)

Poly(acetyl ethylene oxide acrylate‐co‐vinyl acetate) (P(AEOA‐VAc)) was synthesized and used as a host for lithium perchlorate to prepare an all solid polymer electrolyte. Introduction of carbonyl groups into the copolymer increased ionic conductivity. All solid polymer electrolytes based on P(AEOA‐VAc) at 14.3 wt% VAc with 12wt% LiClO₄ showed conductivity as high as 1.2 × 10^?4 S cm^?1 at room temperature. The temperature dependence of the ionic conductivity followed the VTF behavior, indicating that the ion transport was related to segmental movement of the polymer. FTIR was used to investigate the effect of the carbonyl group on ionic conductivity. The interaction between the lithium salt and carbonyl groups accelerated the dissociation of the lithium salt and thus resulted in a maximum ionic conductivity at a salt concentration higher than pure PAEO‐salts system. Copyright © 2010 John Wiley & Sons, Ltd.