Preparation and investigation of tribological properties of ultra‐high molecular weight polyethylene (UHMWPE)/graphene oxide

This article has been devoted to investigation of the tribological properties of ultra‐high molecular polyethylene/graphene oxide nanocomposite. The nanocomposite of ultra‐high molecular polyethylene/graphene oxide was prepared with 0.5, 1.5, and 2.5 wt% of graphene oxide and with a molecular weight of 3.7 × 10⁶ by in‐situ polymerization using Ziegler–Natta catalyst. In this method, graphene oxide was used along with magnesium ethoxide as a novel bi‐support of the Ziegler–Natta catalyst. Analyzing the pin‐on‐disk test, the tribological properties of the nanocomposite, such as wear rate and mean friction coefficient, were investigated under the mentioned contents of graphene oxide. The results showed that an increase in graphene oxide content causes a reduction in both wear rate and mean coefficient friction. For instance, by adding only 5 wt% graphene oxide to the polymeric matrix, the wear rate and mean coefficient friction decreased about 34% and 3.8%, respectively. Also, the morphological properties of the nanocomposite were investigated by using X‐ray diffraction and scanning electron microscopy. In addition, thermal properties of the nanocomposite were analyzed using differential scanning calorimetry, under various contents of graphene oxide. The results of the morphological test indicated that the graphene oxide was completely exfoliated into the polymeric matrix without any agglomeration. Copyright © 2016 John Wiley & Sons, Ltd.     

Effects of charge trapping in gamma irradiated and accelerated aged low-density polyethylene

The effects of gamma irradiation in air and accelerated aging of low-density polyethylene (LDPE) were studied through dielectric loss (tan δ) analysis in the temperature range from 25 to 325 K and using thermally stimulated discharge current (TSDC) measurements. The radiation-induced oxidation was observed using IR spectroscopy. The influence of radiation dose and accelerated aging on the intensities and the positions of the γ and β dielectric relaxation maxima were correlated with maxima of TSDC measurements, and found to be strongly dependent upon the changes in the microstructure of the amorphous phase and on the surface of the crystallites induced by oxidation and crosslinking.     

Influence of gamma irradiation on high density polyethylene/ethylene‐vinyl acetate/clay nanocomposites

The study of high density polyethylene (HDPE)/ethylene‐vinyl acetate (EVA)/and organically‐modified montmorillonite (OMT) nanocomposites prepared by melt intercalation followed by exposure to gamma‐rays have been carried out. The morphology and properties of the nanocomposites were studied using X‐ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and cone calorimetry. The purpose of the study focuses on the influence of gamma irradiation on the morphology, thermal stability and flammability properties of the nanocomposites. XRD studies and TEM images verified that the ordered intercalated nanomorphology of the nanocomposites was not disturbed by gamma irradiation. TGA data showed that the nano‐dispersion of clay throughout the polymer inhibited the irradiation degradation of HDPE/EVA blend, which led to the nanocomposites exhibiting superior irradiation‐resistant properties than that of the pure blend. Cone calorimetry results indicated that the improvement in heat release rate (HRR) for irradiated HDPE/EVA blend was suppressed efficiently when clay was present. Increasing clay loading from 2 to 10% was beneficial by improving the flammability properties of the nanocomposites, but promoted a rapid increase in the sub‐peak HRR at high irradiation dose level. Copyright © 2004 John Wiley & Sons, Ltd.     

Effects of nano graphene oxide as support on the product properties and performance of Ziegler–Natta catalyst in production of UHMWPE

The synthesis of mono‐ and bi‐supported Ziegler–Natta catalysts using magnesium etoxide Mg(OEt)₂ and graphene oxide (GO) as catalyst support for production of Ultra High Molecular Weight Polyethylene (UHMWPE) is reported in this investigation. Nano‐graphene oxide was prepared by the modified Hummer's method and its structure was analyzed by XRD and FTIR indicating the presence of hydroxyl groups on graphene oxide and the formation of an exfoliated structure. The activity of TiCl₄/Mg(OEt)₂, TiCl₄/Mg(OEt)₂‐GO, and TiCl₄/GO catalysts in terms of grams of PE produced per mmol of Ti per hour was experimentally obtained for catalysts with different ratios of co‐catalyst (triisobutylaluminium) to TiCl₄. For all three series of catalysts, the activity curve showed an optimum point at a specific Al/Ti molar ratio. Catalyst activity was highest for TiCl₄/Mg(OEt)₂ and lowest for TiCl₄/GO. The characterization of UHMWPE products indicated that the viscosity average molecular weight (Mv) was highest for the polymer produced by TiCl₄/Mg(OEt)₂ and lowest for the polymer produced by TiCl₄/GO. Furthermore, thermogravimetric analysis (TGA), dynamic mechanical thermal analysis (DMTA), and mechanical tensile testing were conducted on the prepared polymers indicating that the polymer produced by TiCl₄/GO had the highest thermal and mechanical properties, while these properties were at their minimum for polymers produced by TiCl₄/Mg(OEt)₂. Copyright © 2015 John Wiley & Sons, Ltd.     

Post electron-beam irradiation oxidation of orthopaedic UHMWPE

The mechanisms and products of the oxidation process induced by electron-beam irradiation of UHMWPE were thoroughly investigated in the present study. The e-beam technique has the peculiarity of dispensing the whole radiation dose in a very short time and it allows following the post-irradiation oxidation process at room temperature, which represents a major advantage for the present purpose.Thin sections of orthopaedic grade UHMWPE GUR 1050 were irradiated at doses ranging from 5 to 100 kGy in vacuum, air or pure oxygen, depending on the aim of the following analyses. After irradiation, the samples were stored in liquid nitrogen until the measurements began. Chemical and physical changes caused to the polymer by irradiation were investigated by FTIR, derivatisation techniques and spectral subtractions.As reported in the literature, secondary hydroperoxides and ketones were found to be the main oxidation products, along with carboxylic acids and alcohols. Nevertheless, in our case, the kinetics of formation of oxidation products were inconsistent with previously reported mechanisms. An alternative oxidation mechanism, including the simultaneous formation of hydroperoxides and ketones, is proposed. The thermal stability of hydroperoxides is also discussed in detail and the similarities between the post-irradiation oxidation process and the thermal oxidation process are highlighted.     

Effects of low-level gamma irradiation on the characteristics of fermented pork sausage during storage

The effect of gamma irradiation (0.5, 1, 2, and 4 kGy) on the quality of vacuum-packaged dry fermented sausages during refrigerated storage was evaluated. At Day 0 of irradiation, the pH, redness (CIE a^?), yellowness (CIE b^?), 2-thiobarbituric acid-reactive substances (TBARS) and volatile basic nitrogen (VBN) values of samples irradiated at 2 and 4 kGy were higher (p<0.05), but the CIE L^? values (lightness) were lower than those of the non-irradiated control (p<0.05). At<1 kGy irradiation, however, the pH, CIE L^?, CIE a^? and CIE b^?-value of samples were not significantly influenced by irradiation. The CIE a^?, and CIE b^?-values of samples irradiated at 2 and 4 kGy decreased with the increase of storage time. The VBN, TBARS, and CIE L^?-values of samples irradiated at 4 kGy were not changed significantly during refrigerated storage for 90 days (p>0.05). The total plate counts (TPC) and lactic acid bacteria (LAB) in the samples irradiated at 4 kGy were significantly lower (p<0.01) than those with lower irradiation doses. At the end of storage, the TPC, coliform, and LAB in the samples were not increased after irradiation at 1, 0.5 and 1 kGy, respectively. TPC and LAB were not detected in samples irradiated at 4 kGy at Day 90. In addition, no coliform bacteria were found in samples irradiated at 1 kGy during refrigerated storage. Sensory evaluation indicated that the rancid flavor of samples irradiated at 4 kGy was significantly higher, but aroma and taste scores were lower than those of the control at Day 3 of storage. Irradiation of dry fermented sausages at 2 kGy was the best conditions to prolong the shelf-life and decrease the rancid flavor without significant quality deterioration.     

Rheological properties of UHMWPE/iPP blends

The effects of isotactic polypropylene (PP) on the rheological properties of ultra high molecular weight polyethylene (UHMWPE) have been measured in a broad range of composition (0, 5, 15, 30 wt% PP) at various temperatures (110, 130, and 150°C) and a specific gel concentration of 6 wt%. The result showed that the viscosity of the UHMWPE significantly decreased with the addition and increasing amount of PP. Regardless of temperature, the viscosity function followed the power‐law behavior. Copyright © 2009 John Wiley & Sons, Ltd.     

Effects of gamma irradiation on solid and lyophilised phospholipids

The effects of gamma irradiation (25 kGy) as a sterilisation method for phospholipids (distearoylphosphatidylcholine and distearoylphosphatidylglycerol) were investigated. ³¹P-NMR revealed minor chemical degradation of the phospholipids but lower dynamic viscosity and pseudoplasticity, lower turbidity, higher diffusion constant, smaller size, more negative zeta potential and changes in the phase transition behaviour of the subsequently produced liposomes were observed. The observed changes could to some extent be explained by the irradiation-induced degradation products (distearoylphosphatidic acid, fatty acids, lysophospholipids).     

Microstructure and anti‐ wear and corrosion performances of novel UHMWPE/graphene‐nanosheet composite coatings deposited by flame spraying

Ultra‐high molecular weight polyethylene (UHMWPE)/graphene‐nanosheet (GN, multiple layers of graphene sheets with the thickness of ~5–10 nm) coatings have been deposited by flame spraying. The structure of UHMWPE remained almost intact after the spray processing and addition of GNs resulted in a slightly decreased crystallinity and improved thermal stability of UHMWPE. In addition, the coating containing 1.0 wt.% GNs exhibited a reduction of ~20% in wear rate and 25% in friction coefficient (0.18 versus 0.24). Significantly enhanced anti‐corrosion performances of the UHMWPE–GN coatings were suggested by increased corrosion potential, corrosion current density, and impedance modulus value of the UHMWPE–GN coatings. The very well retained GNs are located mainly at the interfaces between UHMWPE splats and act as bridges connecting the splats, which mainly accounts for the enhanced properties of the composite coatings. The novel UHMWPE–graphene composite coatings show great potential for protecting engineering components for applications against corrosion. Copyright © 2013 John Wiley & Sons, Ltd.     

Effects of gamma irradiation on the shoot length of Cicer seeds

The effects of radiation on the shoot and root lengths of germinated seedling of irradiated seeds of Cicer species, i.e. three kabuli types and four desi types of cultivated chickpea (Cicer arietinum Ladiz.) and 2 annual wild types (C. reticulatum Ladiz. and C. bijugum K.H. Rech.) were investigated. The seeds were irradiated with a ⁶⁰Co gamma source using 0, 200, 300 and 400 Gy doses at 1.66 kGy h⁻¹. At 200 Gy minor effects could be observed, but at 400 Gy an obvious depression of shoot length was observed. The kabuli types were more affected than the desi ones. The critical dose that prevented the shoot and root elongation varied among species and also ranged from genotypes to genotype within species.     

LDPE/EVA/graphene nanocomposites with enhanced mechanical and gas permeability properties

In the present work, graphene oxide (GO) and reduced graphene oxide (RGO) were incorporated at low‐density polyethylene (LDPE)/ethylene vinyl acetate (EVA) copolymer blend using solution casting method. Monolayer GO with 1‐nm thickness and good transparency was synthesized using the well‐known Hummers's method. Fourier transform infrared and X‐ray photoelectron spectroscopy data exhibited efficient reduction of GO with almost high C/O ratio of RGO. Scanning electron microscopy showed the well distribution of GO and RGO within LDPE/EVA polymer matrix. The integrating effects of GO and RGO on mechanical and gas permeability of prepared films were examined. Young's modulus of nanocomposites are improved 65% and 92% by adding 7 wt% of GO and RGO, respectively. The tensile measurements showed that maximum tensile strength emerged in 3 wt% of loading for RGO and 5 wt% for GO. The measured oxygen and carbon dioxide permeability represented noticeably the attenuation of gas permeability in composite films compared with pristine LDPE/EVA blend. Copyright © 2015 John Wiley & Sons, Ltd.     

Two-dimensional nanocomposites based on chemically modified graphene

The multiple functional groups and unique two-dimensional (2D) morphology make chemically modified graphene (CMG) an ideal template for the construction of 2D nanocomposites with various organic/inorganic components. Additionally, the recovered electrical conductivity of CMG may provide a fast-electron-transport channel and can thus promote the application of the resultant nanocomposites in optoelectronic and electrochemical devices. This Concept article summarizes the different strategies for the bottom-up fabrication of CMG-based 2D nanocomposites with small organic molecules, polymers, and inorganic nanoparticles, which represent the new directions in the development of graphene-based materials.     

Mechanical properties of fiber reinforced styrene-butadiene rubbers using surface-modified UHMWPE fibers under EB irradiation

Aiming to develop a high performance fiber reinforced rubber of SBR, a special technique using electron beam (EB) irradiation-induced graft-polymerization was applied to ultra-high molecular-weight polyethylene (UHMWPE) fibers. Although UHMWPE is chemically inert, N-vinyl formamide (NVF) could be graft-polymerized onto the UHMWPE fiber surface with this special technique. A maximum grafting percentage of 23.6% was achieved. The composite of SBR and grafted UHMWPE fibers with maximum grafting indicated a linear increase in the initial modulus and strength with the fiber content. At the fiber content of 10%, the initial modulus was improved about five times with respect to that of the pure SBR, while the strength was done about twice. At this moment, only a small reduction could be observed in the strain compared with that of pure SBR. The fiber reinforced rubber with a good performance was obtained in the system of SBR and grafted UHMWPE fibers.     

FTIR Investigation of UHMWPE Oxidation Submitted to Accelerated Aging Procedure

In the present study, an accelerated ageing by oxidative degradation of UHMWPE in hydrogen peroxide solution was performed and the inhibition with ascorbic acid (vitamin C) was analyzed. Both systems were extensively characterized by Fourier Transformed Infrared Spectroscopy (FTIR). Different chemical groups of UHMWPE associated with the degradation reaction were monitored for over 120 days in order to evaluate the possible oxidation mechanisms involved and the inhibitory behavior of vitamin C. The results have provided strong evidence that the oxidation mechanism is rather complex, and 2 stages with their own particular first-order kinetics reaction patterns have been clearly identified. Furthermore, the vitamin C has proven to be an efficient antioxidant for UHMWPE under the evaluated conditions.     

Influence of accelerated aging on clay-reinforced polyamide 6

Organically modified clay-reinforced polyamide 6 was subjected to accelerated heat aging to estimate its long-term thermo-oxidative stability and useful lifetime compared to the virgin material. Changes in molecular weight, and thermal and mechanical properties were monitored and connected to the polymer modification encountered during aging. The incorporation of the clay filler was found to result in moderate polymer degradation during processing, which became more pronounced with aging time at elevated temperature, imparting discoloration. Post-crystallization was favoured by short periods of heat exposure, leading to an increase of crystalline content. Conversely, extended chain scission occurring after prolonged residence time negatively affected crystallites' size, lowering the degree of crystallinity. The aging-induced transformations of crystal structures correlated well with materials' mechanical performance, yielding initially hard and brittle specimens which gradually adopted a softening behavior. Relative to the unfilled polymer, the loss of ductility during aging was milder in the case of nanocomposite, indicating that the clay filler restricted degradation, prolonging durability.     

Physical and mechanical properties of graphene oxide/polyethersulfone nanocomposites

The aim of this study was to investigate physical and mechanical properties of graphene oxide (GO)/polyethersulfone (PES) nanocomposite films. The films were produced by solution casting method. The mechanical properties of composite films were evaluated by tensile test. A significant enhancement in the mechanical properties of neat PES films was obtained incorporating a small amount of GO loading (0.05–1 wt.%). The highest tensile strength was observed at 1 wt.% of GO. Comparisons were made between experimental data and the Halpin–Tsai model predictions for the tensile strength and modulus of GO/PES composites. The effect of an orientation factor on model predictions was also acquired. The hydrophilicity of the nanocomposite was evaluated by assessing contact angle and enhanced wet ability of the films was obtained with increasing the amount of GO up to 1%. The morphology of the nanocomposites was investigated using scanning electron microscopy and transmission electron microscopy and the results revealed a good dispersion of GO in the PES matrix. The thermal behavior of the composite was also studied. Thermal stability of composites was increased by adding the GO. Copyright © 2013 John Wiley & Sons, Ltd.     

Effects of gamma irradiation on different stages of mealybug Dysmicoccus neobrevipes (Hemiptera: Pseudococcidae)

Utilization of phytosanitary irradiation as a potential treatment to disinfest agricultural commodities in trade has expanded rapidly in the recent years. Cobalt-60 gamma ray target doses of 100, 150, 200 and 250 Gy were used to irradiate immatures and adults of Dysmicoccus neobrevipes (Beardsley) (Hemiptera: Pseudococcidae) infesting dragon fruits to find the most tolerant stage and the most optimal dose range for quarantine treatment. In general, irradiation affected significantly all life stages of D. neobrevipes mortality and adult reproduction. The pattern of tolerance to irradiation in D. neobrevipes was 1st instars<2nd instars<3rd instars<adults, in which the adult is the most tolerant stage. Based on obtained results after 21 days of irradiation, predicted doses for 100% mortality of each different development stage in the above mentioned pattern were 224.6, 241.3, 330.9 and 581.5 Gy, respectively. No survived female adult produced offspring at 200 and 250 Gy. Dose range between 200 and 250 Gy could be efficient to prevent the reproduction of this mealybug.     

Effects of gamma irradiation on chemical composition and ruminal protein degradation of canola meal

Gamma irradiation of canola meal (at doses of 25, 50 and 75 kGy) could alter its ruminal protein degradation characteristics by cross-linking of the polypeptide chains. This processing resulted in decrease (linear effect, P<0.001) of ruminal protein degradation and increase (linear effect, P<0.001) of intestinal protein digestibility. The results showed that gamma irradiation at doses higher than 25 kGy can be used as a cross-linking agent to improve protein properties of supplements in ruminant nutrition.     

Effects of dopant concentration and aging on the electrical properties of Y-doped ceria electrolytes

High purity cerium oxide and yttrium oxide were used to form ceria-based solid solution (Ce_1−xY_xO_2−δ, 0.05x0.4) via a conventional mixed-oxide method. All the samples used were aged at 1000 °C in air for 8 days. Crystal structure and microstructure were characterized by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The ionic conductivity (i.e., grain interior (GI) grain boundary (GB) and total conductivities) in this system were systematically studied as a function of dopant content over the temperature range of 250–850 °C in air using an impedance spectroscopy. The lattice parameter decreased with increasing the Y content, but it did not obey Vegard's law. The Y doping had no significant effect on densification behavior and final sintered density, but leading to a significant decrease in grain size as compared to the undoped ceria. The composition x0.1 had a maximum GI conductivity, while a maximum total conductivity was observed at x0.15. A significant high-temperature aging effect was also found for the samples with higher Y doping levels. 10% and 15% decreases in the GI and GB conductivities, respectively, were detected in the aged Ce_0.7Y_0.3O_2−δ ceramic.     

High thermal conductivity EP adhesive based on the GO/EP interface optimized by TDI

Graphene oxide (GO) was used as the filler to modify the epoxy resin (EP) adhesive, and the GO/EP interface was optimized by toluene diisocyanate (TDI) in order to improve the thermal conductivity and T peel strength performance of the adhesive. Through the characterization of the GO product, which was modified by TDI, TDI was grafted onto the surface of GO, and there were NCO groups remaining; thus the chemical bonds were built onto the interface which was non‐wetting between GO and EP. The results of the properties characterization of the adhesive indicated that the bonding properties were significantly enhanced, especially the T peel strength, which was up to 9.62 N/mm, which was contributed by the optimized GO/EP interface. The thermal conductivity of the adhesive increased to 0.624 W m^?1 K^?1, as the interface thermal resistance was reduced after the interface between GO/EP was optimized by TDI. The insulation performance of the adhesive was also improved, since the well‐dispersed GO formed a micro‐capacitance model in EP, and the surface of GO was covered by the EP so that the electronic paths were blocked by the formed chemical bonds.