Polymer nanoparticles: their effect on rheological,thermal, and mechanical properties of linear low‐density polyethylene (LLDPE)

Rheological, thermal, and mechanical properties of polymer particle/LLDPE blends were studied in this paper. The blends were prepared individually by incorporating nanoparticles of polystyrene (nPS) of ～60 nm and polymethyl methacrylate (nPMMA) of ～50 nm with different wt% loading (i.e., 0.10–0.5%). It was shown from the experimental results that rheological, thermal and mechanical properties were increased as polymer particles blended with LLDPE. Blends with 0.25 wt% loading of nPS and 0.5 wt% loading of nPMMA exhibited better rheological, thermal, and mechanical properties compared with that of other wt% loadings. The improvements in properties were due to the close packing of LLDPE chains as recorded by improvement in crystallinity of LLDPE with addition of nPS and nPMMA as shown by SEM. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation and characterization of glass fiber–reinforced polyethylene terephthalate/linear low density polyethylene (GF‐PET/LLDPE) composites

Polyethylene terephthalate (PET) was melt blended with linear low density polyethylene (LLDPE) and subsequently compounded with glass fibers (GF) as reinforcements at percentages ranging from 15 to 45 wt% of LLDPE and 5 to 30 wt% of GF. Thermal, morphological, and mechanical properties of the prepared composites were investigated. It was found that compounding PET/LLDPE blends with GF would be beneficial in producing composites that are thermally stable with good mechanical properties. For example, the impact strength of the composites containing 85/15 wt% (PET/LLDPE) at relatively high loading of GF, ie, from 15 to 30 wt%, was higher than that of the GF‐reinforced neat PET. When increasing the percentage of LLDPE in the composites, the impact strength increased with increasing GF content, and this was also better than that of GF‐reinforced PET whose impact strength drastically decreased upon increasing the GF%. The improvement in mechanical properties of the composite, we suggest, should be correlated with the morphologies of the composites where the visualized interface adhesion tended to be better at higher loadings of both LLDPE and GF.     

Investigating the mechanical,thermal and melt flow index properties of HNTs – LLDPE nano composites for the applications of rotational moulding

Linear low density polyethylene (LLDPE) is the one of the most popular polymer used for rotational moulding applications such as storage tanks. But, its inferior mechanical properties and thermal stability restrict the longer service. Hence, this study experimentally demonstrates the effect of Halloysite Nanotube (HNTs) concentration on LLDPE composites for enhancing the mechanical and thermal stability. HNTs were uniformly dispersed with LLDPE matrix through ultra-sonication, followed by compression moulding used to prepare the nano composites plates. The prepared composites are shown 19.2% improved tensile strength for 2 wt% HNTs, whereas 28.9% hike in flexural strength observed for 4 wt% HNTs composite, compare to neat LLDPE. Which shows that higher concentrations of HNTs is favourable in improving the flexural strength rather than tensile properties. In addition to that, higher concentrations of HNTs are also helping in improving the storage modulus of the LLDPE composites. The increase in mechanical properties mainly attributed due to effective load carriers (HNTs) in the composite. Besides, HNTs were also contributing for improving the melting point and residual char of the composites, which is indeed for storage tanks durability. The prepared composite was thermally stable at higher temperature up to 230 °C, because of HNTs chemical structure, the inner layer of HNTs constitute with Al₂O₃ and outermost layer constitute with SiO_2, both are thermally stable. Stated enhancement proves the potential effect of HNTs reinforcement in the LLDPE composite for rotational moulding applications.     

Mechanical and thermal properties and flame retardancy of phosphorus-containing polyhedral oligomeric silsesquioxane (DOPO-POSS)/polycarbonate composites

A novel polyhedral oligomeric silsesquioxane containing 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO-POSS) has been incorporated into polycarbonate (PC) composites in order to study its effect on mechanical and thermal properties and flame retardancy. The mechanical and thermal properties of the DOPO-POSS/PC composites have been investigated by tensile and flexural testing, DSC, and DMA. Slight enhancements of yield stress, and flexural strength and modulus, and obvious decreases of fracture strength and strain of the DOPO-POSS/PC composites were observed with an increase in DOPO-POSS loading. The glass transition temperatures (T_g) of the composites were reduced with increasing DOPO-POSS loading. The morphology of the PC composites was evaluated by SEM, which indicated that the DOPO-POSS was dispersed with a particle size of 100-250 nm in the PC matrix. The thermal degradation behaviour and flame retardancies of PC composites with different DOPO-POSS loadings were investigated by TGA, LOI, UL-94 standard, and cone calorimetry. The composite had an LOI value of 30.5 and a UL-94 rating V-0 when the content of DOPO-POSS was 4%.     

Synergetic effect of thermal conductivity and flame retardancy of cyanate ester composites containing DOPO and BN with great dielectric properties

DOPO and boron nitride (BN) fillers with different particle sizes and several loadings were employed to improve the properties of cyanate ester (CE) resin. The effects of BN content and particle size on the thermal conductivity of the BN‐DOPO/CE ternary composites were discussed. The influence of enhancing the thermal conductivity of the ternary composites on their flame retardancy was studied. The consequences showed that increasing the thermal conductivity of BN‐DOPO/CE composites had an active impact on their flame retardancy. Approving flame retardancy of the ternary composites was certified by the high limiting oxygen index (LOI), UL‐94 rating of V‐0, and low heat release rate (HRR) and total heat release (THR). For instance, in contrast with pure CE matrix, peak of HRR (pk‐HRR), average of HRR (av‐HRR), THR, and average of effective heat of combustion (av‐EHC) of CEP/BN_{0.5 μm}/10 composite were decreased by 51.7%, 33.8%, 18.7%, and 18.9%, respectively. Thermal gravimetry analysis (TGA) showed that the addition of BN fillers improves the thermal stability of the composites. Moreover, the ternary composites possess good dielectric properties. Their dielectric constants (ε) are less than 3, and dielectric loss tangent (tgδ) values are lower than neat CE resin.     

The mechanical and electrical properties of carbon nanotube‐grafted polyimide nanocomposites

Polyimide (PI)‐based nanocomposites containing aminophenyl functionalized multiwalled carbon nanotubes (AP‐MWCNTs) obtained through a diazonium salt reaction was successfully prepared by in situ polymerization. PI composites with different loadings of AP‐MWCNTs were fabricated by the thermal conversion of poly(amic acid) (PAA)/AP‐MWCNTs. The mechanical and electrical properties of the AP‐MWCNTs/PI composites were improved compared with those of pure PI due to the homogeneous dispersion of AP‐MWCNTs and the strong interfacial covalent bonds between AP‐MWNTs and the PI matrix. The conductivity of AP‐MWNTs/PI composites (5:95 w/w) was 9.32 × 10^?1 S/cm which was about 10¹⁵ times higher than that of Pure PI. The tensile strength and tensile modules of the AP‐MWCNTs/PI composites with 0.5 wt % of AP‐MWCNTs were increased by about 77% (316.9 ± 10.5 MPa) and 25% (8.30 ± 1.10 GPa) compared to those of pure PI, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 960–966     

Controlled migration of antifog additives from LLDPE compatibilized with LLDPE grafted maleic anhydride

This paper summarizes a study of controlled migration of an antifog (AF) additive; sorbitan monooleate (SMO), from linear low density polyethylene (LLDPE) films containing a compatibilizer, LLDPE grafted maleic anhydride (LLDPE‐g‐MA). LLDPE/LLDPE‐g‐MA/SMO blends were prepared by melt compounding. Bulk and surface properties of compression molded LLDPE films containing SMO and LLDPE‐g‐MA were characterized using Fourier transform infrared spectroscopy and contact angle measurements. Thermal properties were investigated using a thermal gravimetric analyzer. Diffusion coefficient (D) was calculated, and AF properties were characterized using a “hot fog” test. Compression molded films were characterized for their morphology using high‐resolution scanning electron microscopy, and rheological properties were measured using a parallel‐plate rotational rheometer. It was found that the LLDPE/LLDPE‐g‐MA/SMO systems are characterized by a slower SMO migration rate, a lower diffusion coefficient, and lower contact angle values compared with LLDPE/SMO blends. These results are well correlated with results of a hot fog test. Morphological studies revealed a very fine dispersion of SMO in the LLDPE films, when 3 phr LLDPE‐g‐MA was combined with 1 phr SMO. Thermal analysis results show that the incorporation of 3 phr LLDPE‐g‐MA and 1 phr SMO significantly increases the decomposition temperature of the blend at T > 400°C. At high shear rates, the LLDPE blends show that the AF and the compatibilizer have a lubrication effect on LLDPE. Copyright © 2014 John Wiley & Sons, Ltd.     

Graphene and MnO2 decorated graphene filled composites for electromagnetic shielding applications having excellent dielectric properties

Graphene nanoplatelets (GnP) and α-MnO₂ decorated GnP were integrated into an ethylene vinyl acetate (EVA) matrix using the dual mixing method (solution followed by melt mixing). GnP was added in 1, 3, 5, 8, 10 and 15 phr loadings into an EVA matrix to obtain composites and evaluate their various properties suitable for mechanical and electrical applications. The graphene nanoplatelets were further decorated with α-MnO₂ which was subsequently integrated into EVA at an 8 phr loading to form composites. It was observed in the GnP-EVA composites, that with an increasing GnP content, a substantial increase in the tensile strength (188%) over the neat polymer was observed at a 10 phr loading but reduced thereafter at a 15 phr loading. Dielectric permittivity of the composites were observed to increase with an increasing filler loading, the addition of α-MnO₂ also having a beneficial effect. Conductivity as well as the electromagnetic interference shielding performance were improved with increasing GnP concentrations. A maximum 28 dB of shielding was observed in the 15 phr loaded GnP-EVA composite whereas the α-MnO₂ decorated GnP-EVA composite showed a shielding efficiency of 22 dB at a concentration of 8 phr for a thickness of 2 mm with excellent thermal and mechanical properties. Overall, the composite material will find its application as a flexible EMI shielding material.     

IFSS, TG, FT-IR spectra of impregnated sugar palm (Arenga pinnata) fibres and mechanical properties of their composites

This study aimed to investigate the effect of resin impregnation on the interfacial shear strength (IFSS), thermogravimetric (TG) and fourier transform infrared (FT-IR) of sugar palm (Arenga pinnata) fibres. In addition, the effect of resin impregnation on the mechanical properties of sugar palm fibre reinforced unsaturated polyester (UP) composites was also studied. The fibres were impregnated with UP via vacuum resin impregnation process at a pressure of 600 mmHg for 5 min. Composites of 10, 20, 30, 40 and 50 % fibre loadings were fabricated and tested for tensile and flexural properties. It was observed that the impregnation process caused the fibres to be enclosed by UP resin and this gave a strong influence to the increase of its interfacial bonding by the increase of its IFSS from single fibre pull-out test. It was also observed with TG and FT-IR spectra that the impregnated fibre had lower moisture uptake than the control and there was no significant increase in thermal stability of the impregnated fibre. The sequence of fibre decomposition started from the evaporation of moisture, hemicelluloses, cellulose, lignin and finally ash content and the presence of these components were proven by FT-IR spectra. For the composite specimens, due to the high interfacial bonding of the impregnated fibre and the matrix, the impregnated composites showed consistently higher tensile strength, tensile modulus, elongation at break, flexural strength, flexural modulus and toughness than the control samples. It was also observed that 30 % fibre loading gave optimum properties.     

Morphology,structure, and properties of in situ compatibilized linear low‐density polyethylene/polystyrene and linear low‐density polyethylene/high‐impact polystyrene blends

Blends of linear low‐density polyethylene (LLDPE) with polystyrene (PS) and blends of LLDPE with high‐impact polystyrene (HIPS) were prepared through a reactive extrusion method. For increased compatibility of the two blending components, a Lewis acid catalyst, aluminum chloride (AlCl₃), was adopted to initiate the Friedel–Crafts alkylation reaction between the blending components. Spectra data from Raman spectra of the LLDPE/PS/AlCl₃ blends extracted with tetrahydrofuran verified that LLDPE segments were grafted to the para position of the benzene rings of PS, and this confirmed the graft structure of the Friedel–Crafts reaction between the polyolefin and PS. Because the in situ generated LLDPE‐g‐PS and LLDPE‐g‐HIPS copolymers acted as compatibilizers in the relative blending systems, the mechanical properties of the LLDPE/PS and LLDPE/HIPS blending systems were greatly improved. For example, after compatibilization, the Izod impact strength of an LLDPE/PS blend (80/20 w/w) was increased from 88.5 to 401.6 J/m, and its elongation at break increased from 370 to 790%. For an LLDPE/HIPS (60/40 w/w) blend, its Charpy impact strength was increased from 284.2 to 495.8 kJ/m². Scanning electron microscopy micrographs showed that the size of the domains decreased from 4–5 to less than 1 μm, depending on the content of added AlCl₃. The crystallization behavior of the LLDPE/PS blend was investigated with differential scanning calorimetry. Fractionated crystallization phenomena were noticed because of the reduction in the size of the LLDPE droplets. The melt‐flow rate of the blending system depended on the competition of the grafting reaction of LLDPE with PS and the degradation of the blending components. The degradation of PS only happened during the alkylation reaction between LLDPE and PS. Gel permeation chromatography showed that the alkylation reaction increased the molecular weight of the blend polymer. The low molecular weight part disappeared with reactive blending. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1837–1849, 2003     

Rheological properties of ferrite nanocomposites based on nylon‐66

Effects of ferrite nanoparticles (0.1–20 wt %) on the rheological and other physical properties of nylon‐66 were investigated. The presence of ferrite nanoparticles less than 1 wt % increased the crystallization temperature (T_c) by 4.2 °C with ferrite content, but further addition decreased T_c. The onset temperature of degradation was increased by 7.3 °C at only 0.1 wt % loading of ferrite, after which the thermal stability of nylon‐66 was decreased with ferrite content. The incorporation of ferrite nanoparticles more than 5 wt % increased the dynamic viscosity (η′) with the loading level. Further, it produced notably shear thickening behavior in the low frequency, after which high degree of shear thinning was followed with ferrite content. In the Cole–Cole plot, the nanocomposites with ferrite lower than 5 wt % presented a single master curve, while further addition gave rise to a deviation from the curve. The relaxation time (λ) was increased with ferrite content and the difference of λ between nylon‐66 and its nanocomposite was greater at lower frequency. The tensile strength was a little increased up to 1 wt % loading, after which it was decreased with increasing the loading level. In addition, the introduction of the nanoparticles increased tensile modulus and decreased the ductility with ferrite content. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 371–377, 2006     

Ocimum basilicum seed mucilage reinforced with montmorillonite for preparation of bionanocomposite film for food packaging applications

Use of nanocomposites is a well-established approach in enhancing the mechanical and barrier properties of bionanocomposite film for food packaging applications. The seed mucilage of Ocimum basilicum was employed for the preparation of bionanocomposite films with montmorillonite (MMT) as nanofiller. The films were prepared by solvent-casting method at varied solution pH (1, 3, 5 and 9) and MMT loading (1%, 3%, 5%, 10%, 15% and 20%). The films were characterized for physical, mechanical and barrier properties in addition to microstructure and X-ray diffraction pattern. XRD analysis revealed the exfoliated dispersion of MMT at pH 9, confirming its effective interaction with the bionanocomposite film. Maximum film tensile strength was achieved at a lower MMT load of 5%. Water vapour permeability reduced with increase in MMT loading up to 5%, followed by an increase at higher MMT loadings. Film formed at pH 9 showed tensile strength of 17.3 ± 0.33 MPa and reduced water vapour permeability (WVP) of 0.21 g mm.m⁻².hr⁻¹.kPa⁻¹.     

Dynamically cured natural rubber/EVA blends: influence of NR‐g‐poly(dimethyl (methacryloyloxymethyl)phosphonate) compatibilizer

Graft copolymer of natural rubber and poly(dimethyl(methacryloyloxymethyl)phosphonate) (NR‐g‐PDMMMP) was prepared in latex medium via photopolymerization. It was then used to promote the blend compatibility of dynamically cured 40/60 natural rubber (NR)/ethylene vinylacetate copolymer (EVA) blends using various loading levels at 1, 3, 5, 7, 9, 12, and 15 wt%. It was found that the increasing loading levels of NR‐g‐PDMMMP in the blends caused the increasing elastic modulus and complex viscosity until reaching the maximum values at a loading level of 9 wt%. The properties thereafter decreased with the increasing loading levels of NR‐g‐PDMMMP higher than 9 wt%. The smallest vulcanized rubber particles dispersed in the EVA matrix with the lowest tan δ value was also observed at a loading level of 9 wt%. Furthermore, the highest tensile strength and elongation at break (i.e., 17.06 MPa and 660%) as well as the lowest tension set value (i.e., 27%) were also observed in the blend using this loading level of the compatibilizer. Addition of NR‐g‐PDMMMP in the dynamically cured NR/EVA blends also improved the thermal stability of the blend. That is, the decomposition temperature increased with the addition of the graft copolymer. However, the addition of NR‐g‐PDMMMP in the blends caused the decreasing degree of crystallinity of the EVA phase in the blend. However, the strength properties of the blend are still high because of the compatibilizing effect. Copyright © 2009 John Wiley & Sons, Ltd.     

Comparative study on the effect of partial replacement of silica or calcium carbonate by bentonite on the properties of EPDM composites

The effects of the partial replacement of silica or calcium carbonate (CaCO₃) by bentonite (Bt) on the curing behaviour, tensile and dynamic mechanical properties and morphological characteristics of ethylene propylene diene monomer (EPDM) composites were studied. EPDM/silica/Bt and EPDM/CaCO₃/Bt composites containing five different EPDM/filler/Bt loadings (i.e., 100/30/0, 100/25/5, 100/15/15, 100/5/25 and 100/0/30 parts per hundred rubber (phr)) were prepared using a laboratory scale two-roll mill. Results show that the optimum cure (t₉₀) and scorch (t_S2) time decreased, while the cure rate index (CRI) increased for both composites with increasing Bt loading. The tensile properties of EPDM/CaCO₃/Bt composites increased with the replacement of CaCO₃ by Bt from 0 to 30 phr of Bt. For EPDM/silica/Bt composites, the maximum tensile strength and E_b were obtained at a Bt loading of 15 phr, with enhanced tensile modulus on further increase of Bt loading. The dynamic mechanical studies revealed a strong rubber-filler interaction with increasing Bt loading in both composites, which is manifested by the lowering of tan δ at the glass transition temperature (Tg) for EPDM/CaCO₃/Bt composites and tan δ at 40 °C for EPDM/silica/Bt composites. Scanning electron microscopy (SEM) micrographs proved that incorporation of 15 phr Bt improves the dispersion of silica and enhances the interaction between silica and the EPDM matrix.     

Effects of thermal ageing on mechanical and thermal behaviors of linear low density polyethylene pipe

The mechanical and thermal behaviors of linear low density polyethylene (LLDPE) pipe with variation in thermal exposure time were studied. The prolongation of thermal exposure time leads to a progressive increase, until 6000 h, in tensile strength and a slight increase in hardness, while a proportional decrease in elongation at break. These results can be explained by the increase of crystallinity, followed by the increase of crosslinking density and the decrease in chain mobility due to thermal oxidation as the exposure time increases. The additional ageing to the antioxidant-depleted LLDPE pipe induces the formation of T2 endotherm, which leads to a negative effect in mechanical properties. Long-term hydrostatic pressure test result implies the existence of transition point from ductile to brittle fracture in terms of the thermal exposure time. Chemiluminescence (CL) and oxidation induction time (OIT) tests are employed to monitor the thermo-oxidative degradation of LLDPE pipe. The CL emission intensity increases with increasing with thermal exposure time. Furthermore, the OIT result suggests that after 6000 h of the thermal ageing, the depletion of antioxidant originally added in LLDPE pipe occurs. Fourier transform-infrared spectroscopy results show the increase of carbonyl (-CO) and hydroxyl (O-H) function groups on the surface of thermally exposed LLDPE pipe. This result suggests that the hydrocarbon groups locally undergo the oxidation on the LLDPE surface due to thermal degradation.     

Synthesis and properties of poly(isobutyl methacrylate‐co‐butanediol dimethacrylate‐co‐methacryl polyhedral oligomeric silsesquioxane) nanocomposites

Poly[isobutyl methacrylate‐co‐butanediol dimethacrylate‐co‐3‐methacrylylpropylheptaisobutyl‐T8‐polyhedral oligomeric silsesquioxane] [P(iBMA‐co‐BDMA‐co‐MA‐POSS)] nanocomposites with different crosslink densities and different polyhedral oligomeric silsesquioxane (MA‐POSS) percentages (5, 10, 15, 20, and 30 wt %) were synthesized by radical‐initiated terpolymerization. Linear [P(iBMA‐co‐MA‐POSS)] copolymers were also prepared. The viscoelastic properties and morphologies were studied by dynamic mechanical thermal analysis, confocal microscopy, and transmission electron microscopy (TEM). The viscoelastic properties depended on the crosslink density. The dependence of viscoelastic properties on MA‐POSS content at a low BDMA loading (1 wt %) was similar to that of linear P(iBMA‐co‐MA‐POSS) copolymers. P(iBMA‐co‐1 wt % BDMA‐co‐10 wt % MA‐POSS) exhibited the highest dynamic storage modulus (E′) values in the rubbery region of this series. The 30 wt % MA‐POSS nanocomposites with 1 wt % BDMA exhibited the lowest E′. However, the E′ values in the rubbery region for P(iBMA‐co‐3 wt % BDMA‐co‐MA‐POSS) nanocomposites with 15 and 30 wt % MA‐POSS were higher than those of the parent P(iBMA‐co‐3 wt % BDMA) resin. MA‐POSS raised the E′ values of all P(iBMA‐co‐ 5 wt % BDMA‐co‐MA‐POSS) nanocomposites in the rubbery region above those of P(iBMA‐co‐5 wt % BDMA), but MA‐POSS loadings < 15 wt % had little influence on glass‐transition temperatures (T_g's) and slightly reduced T_g values with 20 or 30 wt % POSS. Heating history had little influence on viscoelastic properties. No POSS aggregates were observed for the P(iBMA‐co‐1 wt % BDMA‐co‐MA‐POSS) nanocomposites by TEM. POSS‐rich particles with diameters of several micrometers were present in the nanocomposites with 3 or 5 wt % BDMA. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 355–372, 2005     

Synthesis and characterization of phenyl polysiloxane modified polyurea/polyurethanes

A series of phenyl polysiloxane‐modified polyurea/polyurethanes ( SPUs ) with different silicone loadings (10, 20, 30, and 40 wt %) have been designed and synthesized. The structures of SPUs were confirmed by ¹H NMR, ¹³C NMR, and FT‐IR. The impact of phenyl polysiloxane content on the properties of SPUs was fully studied. The residual methoxy groups on silicon could help SPUs form interpenetrating networks accompanying with the residual isocyanate under moisture, which was different with the conventional moisture‐crosslinking polyurethane system. The properties of SPUs films have been fully researched by attenuated total reflection flourier transformed infrared spectroscopy, thermal analysis, tensile tests, water contact angle, X‐ray photoelectron spectroscopy, SEM, and AFM. Results indicated that the introduction of phenyl polysiloxane improved the thermal stability and remarkably increased the water contact angles accompanying with a comparable mechanical strength to the pure polyurethane. Meanwhile, it also brought out the decreased microphase separation and water absorption. The obvious surface migration has been observed in the SPUs , which changed their surface properties. Some voids were observed in all moisture curing SPUs system, but the phenyl silicone content impacted on the numbers and sizes of the voids. The phenyl groups introduced and carbon dioxide produced in the crosslinking procedure helped to form and stabilize the voids in the SPUs . © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1794–1805     

Plasticization and cocrystallization in LLDPE/wax blends

The structure and thermal properties of linear low‐density polyethylene (LLDPE)/medium soft paraffin wax blends, prepared by melt mixing, were investigated by differential scanning calorimetry (DSC) and small‐ and wide‐angle X‐ray scattering (SAXS and WAXS). The blends form a single phase in the melt as determined by SAXS. Upon cooling from the melt, two crystalline phases develop for blends with more than 10 wt % wax characterized by widely different melting points. The wax acts as an effective plasticizer for LLDPE, decreasing both its crystallization and melting temperature. The higher melting point crystalline phase is formed by less branched LLDPE fractions. On the other hand, the lower melting point crystalline phase is a wax‐rich phase constituted by cocrystals of extended chain wax and short linear sequences of highly branched LLDPE chains. The presence of cocrystals was evidenced by standard DSC results, successive self‐nucleation and annealing (SSA) thermal fractionation and by the detection of a new SAXS signal attributed to the lamellar long period of the cocrystals. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1469–1482     

高分散在氮掺杂碳纳米管表面铂纳米粒子的高效甲醇电氧化性能

以氮掺杂碳纳米管(NCNT)为载体,利用掺杂氮原子的锚定作用,通过微波辅助乙二醇还原法方便地将Pt纳米粒子高分散地固载于NCNT表面,制得了Pt/NCNT系列催化剂,对催化剂制备规律、电催化甲醇氧化反应(MOR)性能及构效关系开展了系统深入的研究。结果表明,随Pt负载量在18.2%~58.7%(w/w,下同)范围增加,Pt纳米粒子的粒径在2.2~3.7 nm范围相应地逐渐增大。单位质量催化剂的MOR催化活性先增加后急剧减小,在负载量为47.8%时达到最大。Pt的质量比活性在中等负载量(27.6%~47.8%)区间出现高值平台。该变化规律源于Pt纳米粒子的MOR催化活性在3 nm前后的明显差异,即3 nm时活性差,3 nm时活性优异。高负载量(58.7%)时活性的急剧下降源于Pt纳米粒子因团聚引起的Pt利用率的降低。     

Nanostructured CoMoO4 Supported on Mesoporous SBA-15 for Catalytic Oxidative Dehydrogenation of Propane to Propene

Nanostructured cobalt molybdate catalysts supported on mesoporous silica SBA-15 with different loadings were prepared by citric acid coordination-impregnation method and characterized by XRD, TEM, and BET techniques. The characterization results showed that high loading of well-dispersed crystalline CoMoO₄ may be achieved using citric acid coordination-impregnation method and the mesoporous structure of the support remained intact. The catalytic activity of these catalysts in the oxidative dehydrogenation of propane was investigated. The catalysts of nanostructured cobalt molybdate supported on mesoporous silica SBA-15 showed better catalytic performance than the corresponding bulk composite oxide and nanostructured CoMoO₄ supported on SBA-15 with loading of 13% (mass fraction, w) displayed propene yield of 16.8% at 823 K.