Extraction and determination of pyridinium ionic liquid cations in environmental water samples by using strong cation exchange solid phase extraction and ion chromatography

This paper presents a novel analytical method for the determination of pyridinium ionic liquid cations in environmental water samples by ion chromatography coupled with solid phase extraction. The water samples were purified and enriched by a sulphonic acid extraction column, and then the impurities were washed with 10 mL water – 20% (v/v) acetonitrile solution and the analytes eluted with 0.5 mol L^?1 phosphoric acid – sodium dihydrogen phosphate buffer solution – 55% methanol. The eluted analytes were determined by ion chromatography with 3.0 mmol L^?1 methane sulphonic acid – 8% acetonitrile as the mobile phase and direct conductivity detection. Three pyridinium cations were completely separated in 20 min and the retention mechanism basically conforms to the ion exchange mode. The newly developed method has been successfully applied to the analysis of pyridinium cations in spiked environmental water samples, which provided satisfactory recoveries in the range of 98.8% to 100.0% with the relative standard deviations less than 2.8%. The concentration of 0.004 to 0.01 mg L^?1 in water samples can be preconcentrated by this method. The method is accurate, reliable, simple and practical. This research provides a new reference for detecting ionic liquid cations in environmental water samples and studying the environmental risk assessment of ionic liquids.     

Microwave-assisted micellar extraction coupled with solid-phase extraction for preconcentration of pharmaceuticals in molluscs prior to determination by HPLC

A simple and specific analytical method was developed and tested for the determination of pharmaceuticals in mollusc samples. A combination of microwave-assisted micellar extraction (MAME) and solid-phase extraction (SPE) using a non-ionic surfactant, polyoxyethylene 10 lauryl ether, was examined to extract and determine simultaneously a group of pharmaceuticals such as carbamazepine, clorfibric acid, ketoprofen, naproxen, bezafibrate and ibuprofen by liquid chromatography using UV-diode array detector. The MAME extraction performance was evaluated by studying various parameters such as the volume and concentration of surfactant and microwave conditions. Finally, an OASIS HLB cartridge was used as an optimum SPE sorbent to clean up the extracts and preconcentrate the selected analytes. The proposed method showed satisfactory linearity and reproducibility (between 3 and 15%), as well as detection limits ranging from 30 to 220 ng/g. Finally, the method was successfully applied to the determination of the target pharmaceuticals in various kinds of mollusc samples. This study has demonstrated that microwave-assisted micellar extraction with solid-phase extraction may be used as a viable alternative to conventional methods for the extraction of pharmaceuticals in this type of matrices.     

Simultaneous extraction and determination of fluoroquinolones,tetracyclines and sulfonamides antibiotics in soils using optimised solid phase extraction chromatography-tandem mass spectrometry

An analytical method was developed for the simultaneous extraction and determination of 18 fluoroquinolones (FQs), tetracyclines (TCs) and sulfonamides (SAs) antibiotics from soils using solid phase extraction and liquid chromatography-tandem mass spectrometry. The soils were extracted by different solvents with the help of mechanical shaking and ultrasonic treatment at 59?kHz, followed by a strong anion exchange (SAX) cartridge to clean up soil samples and a hydrophilic lipophilic balance (HLB) cartridge as enrichment. The method was evaluated by testing the following variables: extraction solvents, the type of SPE cartridges, solvent volumes, initial spiking levels and soil types (silty clay loam and clay loam soils). The soil extraction method was validated using these two types of soils, representing two typical agricultural soils in northern China. For 2?g soil, the extraction steps with the mixture of potassium phosphate buffer and acetonitrile (ACN) (1/1, v/v, pH 3.2) provided satisfactory recoveries. In the clay loam soil, the recoveries of all the compounds were from 56% to 89% at the spiking level of 50?µg?kg^?1 soil, and from 69% to 97% at the spiking level of 200?µg?kg^?1 soil, respectively. Recoveries in silty clay loam soil were similar to that in clay loam. The method was successfully employed using soil samples collected from a farmland and afforestion area irrigated with sewage in northern China. The result indicates that trace antibiotics in sewage may accumulate in soil irrigated by river water containing sewage.     

固相萃取-高效液相色谱法同时测定鸡粪中四环素类、喹诺酮类和磺胺类抗生素

建立了一种高效、低成本的固相萃取-高效液相色谱（SPE-HPLC）同时测定鸡粪中6种常见抗生素（2种四环素类、2种喹诺酮类和2种磺胺类）的分析方法。样品经EDTA-McIlvaine缓冲液和有机混合提取液（甲醇-乙腈-丙酮，2：2：1，v/v/v）提取，过HLB固相萃取柱净化，甲醇-二氯甲烷（7：3，v/v）洗脱，高效液相色谱-二极管阵列检测器测定，检测波长λ=270 nm，柱温32℃，流动相为乙腈-0.7%（v/v）磷酸水溶液。该方法在0.5~100 mg/L质量浓度范围内的标准曲线相关系数r²在0.9999~1之间，样品加标回收率在70.0%~116.3%之间，相对标准偏差为1.2%~16.6%。方法检出限为1.3~6.7 μg/kg，定量限为3.5~9.2 μg/kg。应用该方法对辽宁省抚顺市某养鸡场当天的鸡粪进行检测，诺氟沙星和恩诺沙星（喹诺酮类）含量为未检出~9.23 mg/kg和1.57~7.69 mg/kg，磺胺二甲嘧啶（磺胺类）含量为2.02~13.05 mg/kg，磺胺甲恶唑、土霉素和四环素未测出。     

A selective modified nanoporous silica as sorbent for separation and preconcentration of dysprosium in water samples prior to ICP-OES determination

In this research a new physically functionalized nanoporous silica (SBA-15) using N′-[(2-hydroxy phenyl) methylene] benzohydrazide (BBH) was utilized as a selective sorbent for the separation, preconcentration and determination of dysprosium (Dy) in natural water by inductively coupled plasma optical emission spectrometry (ICP-OES). The selectivity of BBH to Dy (III) ion was previously tested by conductometric and spectroscopic methods. Conditions for effective adsorption of Dy were optimized with respect to experimental parameters in batch process. The extraction recovery was 96.5, analytical curve was linear in the range 0.2–1000?µgL^?1, and the detection limit was 0.05?ng?mL^?1. The relative standard deviation (RSD) under optimal conditions was 3.2% (n?=?10). The sorbent exhibited high adsorption capacity and fast rate of equilibrium for sorption of Dy ions. The method was applied for recovery and determination of dysprosium in different environmental water samples.     

A novel silica supported chitosan/glutaraldehyde as an efficient sorbent in solid phase extraction coupling with HPLC for the determination of Penicillin G from water and wastewater samples

In this study, silica@chitosan-glutaraldehyde (Si@Cs-G) was synthesized as a novel adsorbent for extraction of Penicillin G (PG) from the synthetic and real samples followed by HPLC determination. The synthesized adsorbents were characterized by the scanning electron microscopy (SEM), X-ray diffraction (XRD), fourier transform infrared (FTIR), dynamic light scattering (DLS), transmission electron microscopy (TEM) and nitrogen adsorption–desorption techniques. The factors influencing the extraction efficiency including pH, sorbent dose, extraction time, extraction solvent type and its volume were investigated and optimized.Under the optimal conditions (sorbent dosage: 25 mg, desorption solvent (acetonitrile) with volume of 0.75 mL; pH: 6 and extraction time: 50 min), the Si@Cs-G demonstrated high efficiency and linearity (R² > 0.999) with the concentration of penicillin G ranging from 1 to 300 μg L⁻¹. Extraction recovery in synthetic samples was 98.977%, with LOD = 0.493 μg L⁻¹, LOQ = 1.638 μg L⁻¹ and RSD < 1.953%. The method was successfully applied for determination of PG in real water samples (tap, river, lake and well water) and wastewater samples (SH and SHB hospital effluent). The obtained relative recoveries were in the range of 91.31% -123.27% with RSD less than 6.34% for all the real samples. The dominant mechanism in the PG adsorption process was involved in the π-π interaction, hydrogen bonding, and electrostatic interaction.     

Application of multiwalled carbon nanotubes as solid phase extraction sorbent for preconcentration of trace copper in water samples

The adsorption behavior of multiwalled carbon nanotubes (MWNTs) toward copper has been investigated systemically, and a new method has been developed for the determination of trace copper in water samples based on preconcentration with a microcolumn packed with MWNTs prior to its determination by flame atomic absorption spectrometry. The optimum experimental parameters for preconcentration of copper, such as pH of the sample, sample flow rate and volume, elution solution and interfering ions, have been investigated. Copper can be quantitatively retained by MWNTs in the pH range 5-8, and then eluted completely with 0.5 M HNO3. The detection limit of this method for Cu was 0.42 ng/mL, and the RSD was 3.5% at the 10 ng/mL Cu level. The method was validated using a certified reference material, and has been successfully applied for the determination of trace copper in water samples.     

Magnetic solid phase extraction based on phenyl silica adsorbent for the determination of tetracyclines in milk samples by capillary electrophoresis

A magnetic solid phase extraction method coupled to capillary electrophoresis is proposed for the determination of tetracycline, oxytetracycline, chlortetracycline and doxycycline in milk samples. Five different magnetic phenyl silica adsorbents covered with magnetite were synthesized by varying the molar ratio of phenyltrimethylsilane and tetramethylorthosilicate; these adsorbents were evaluated in terms of their pH and degree of hydrophobicity for tetracycline retention. The optimal, selected combination of conditions was a pH of 10.0 and a magnetic sorbent ratio of 4:1; under these conditions, the retention capacity ranged from 99.7% to 101.2% for the four tetracyclines analyzed. The elution conditions and initial sample volume of the proposed extraction method were also optimized, and the best results were obtained with 1×10(-3) M acetic acid in methanol as eluent and a 200 ml of sample volume. Under optimal conditions, average recoveries ranged from 94.2% to 99.8% and the limits of detection ranged from 2 to 9 μg l(-1) for the four tetracyclines. After the proposed method was optimized and validated, 25 milk samples of different brands were analyzed, oxytetracycline residues were detected in five samples, in concentrations ranging from 98 to 213 μg l(-1). Subsequent analysis of positive samples by SPE-CE and magnetic solid phase extraction-HPLC revealed than no significant differences were found from results obtained by the proposed methodology. Thus, the developed magnetic extraction is a robust pre-concentration technique that can be coupled to other analytical methods for the quantitative determination of tetracyclines.     

分散固相萃取净化-超高效液相色谱-串联质谱法测定鸡蛋和鸡肉中金刚烷胺和金刚乙胺残留

建立了鸡蛋和鸡肉中金刚烷胺和金刚乙胺残留量的分散固相萃取-超高效液相色谱-串联质谱测定方法。鸡蛋和鸡肉样品经氨水-乙腈(2 : 98, v/v)提取后,提取液经氮气吹干至1 mL后,利用C18和NH₂填料进行分散固相萃取净化,过滤膜后分析。采用ZORBAX C18色谱柱分离,用1 mmol/L乙酸铵水溶液(含0.1%(v/v)甲酸)-甲醇作为流动相进行梯度洗脱,正离子多反应监测模式。结果表明,金刚烷胺和金刚乙胺在0.15~10.0 μ g/L范围内具有较好的线性关系,鸡蛋和鸡肉中的检出限均为0.05 μ g/kg,定量限均为0.20 μ g/kg。当2种药物在鸡蛋和鸡肉中的加标水平为0.2、1.0和2.0 μ g/kg时,平均回收率范围为89%~108%,相对标准偏差范围为5.0%~8.6%。该方法能够满足鸡蛋和鸡肉中金刚烷胺和金刚乙胺残留量分析的要求。     

固相萃取-高效液相色谱法同时测定食品中4种合成色素

以可代替使用的水溶性合成色素-亮黑BN、固绿FCF、酸性红、酸性黄36为研究对象,建立了高效液相色谱同时测定食品中4种合成色素的方法。样品通过WAX固相萃取柱富集净化,10%氨化甲醇洗脱,采用C18色谱柱分离,以甲醇和10 mmol/L乙酸铵水溶液作为流动相梯度洗脱,外标法定量。通过固相萃取柱净化后,杂质对待测物的干扰明显降低,优化色谱条件下,4种色素在0.10~10.0 mg/L质量浓度范围内,线性良好,相关系数(r)≥0.9995。方法回收率为92.6%~101.8%,相对标准偏差(RSD)≤5.4%,方法检出限为0.01~0.04 mg/kg。该方法灵敏度高,准确可靠,适合食品中亮黑BN、固绿FCF、酸性红、酸性黄36的同时测定。     

固相萃取-高效液相色谱法同时测定牛奶中22种磺胺类兽药残留

建立了一种基于固相萃取技术同时测定牛奶中22种磺胺类兽药残留的高效液相色谱分析方法.样品经乙腈-甲酸混合溶液提取,乙腈饱和的正己烷除酯后,HLB固相萃取柱净化,以甲醇-2 mmol/L乙酸铵(含0.2％乙酸)为流动相进行梯度洗脱,XBridge C18色谱柱进行分离,采用光电二极管阵列检测器检测,外标法定量.磺胺类化合...     

分散固相萃取-高效液相色谱法快速测定果蔬中的6种保鲜剂残留量

建立了采用分散固相萃取-高效液相色谱同时测定果蔬中2,4-滴、噻苯咪唑、乙萘酚、邻苯基苯酚、二苯醚和联苯6种保鲜剂残留量的方法。样品经乙腈提取(同时加入氯化钠和无水硫酸镁),提取液经酸性氧化铝分散固相萃取净化,采用Agilent TC C18色谱柱(250 mm×4.6 mm, 5 μm),以甲醇-0.02 mol/L的磷酸二氢钾溶液(pH 6)作为流动相,流速1.0 mL/min,梯度洗脱,用紫外检测器检测,检测波长为235 nm,外标法峰面积定量。6种保鲜剂在0.5～20 mg/L范围内线性关系良好,相关系数均大于0.99; 6种保鲜剂在样品中添加1、2和10 mg/kg 3个浓度水平的回收率为84.2%～99.1% (n=6),相对标准偏差为1.67%～10.3%;方法的定量限为1 mg/kg。该法简便、准确,适用于果蔬中6种保鲜剂残留量的检测。     

Microwave-assisted solid phase extraction prior to ICP-MS determination of Pd and Pt in environmental and biological samples

A sensitive and selective microwave-assisted solid phase extraction procedure coupled to inductively coupled plasma-mass spectrometry (ICP-MS) is proposed for palladium (Pd) and platinum (Pt) quantification in environmental and biological samples. Pd and Pt were quantitatively retained on commercial thioureido propyl functionalised silica gel packed inside a home-made glass microcolumn, and later eluted with 0.5% thiourea solution under microwave irradiation, followed by ICP-MS determination. The main variables affecting the procedural stages (i.e., sorption and desorption) and ICP-MS determination were optimised. The best conditions found were: (a) sorption: sample acidity, 1?M HCl; sample flow rate, 3?mL?min^?1; (b) desorption: microwave radiation, power 800?W; eluent concentration, 0.5% thiourea; eluent flow rate, 0.5?mL?min^?1; (c) ICP-MS determination: nebuliser feeding, free aspiration (0.3?mL?min^?1); internal standard, Rh (5?µg?L^?1). Analyte recoveries were higher than 90% and concentration factors up to 90 and 92 were achieved for Pd and Pt, respectively. Depending on the conditions, the methodological limits of detection were down to 0.2?ng?L^?1 for both analytes and repeatability, expressed as RSD%, varied between 1.3 and 11.0%. A method selectivity evaluation showed that most of the ICP-MS interferents were either quantitatively separated or more than 86% eliminated, except for Cu (elimination efficiency around 30%). Finally, the method was successfully used to determine Pd in certified reference materials (i.e. human urine and serum) and Pd and Pt in PM₁₀ airborne particulate matter fractions.     

Determination of cephalosporin antibiotics in water samples by optimised solid phase extraction and high performance liquid chromatography with ultraviolet detector

A reliable and robust analytical method based on solid phase extraction (SPE) and high performance liquid chromatography (HPLC) with ultraviolet (UV) detector was developed for the simultaneous determination of five cephalosporin antibiotics (Ceftazidime, Cefradine, Cefaclor, Cefotaxime and Cefoperazone) in various water samples. Under optimised conditions, it was applicable to preconcentrate up to 500?ml of water samples in the OASIS HLB cartridges with reasonable recoveries for all the cephalosporin antibiotics tested. Recoveries were as follows: deionised water, tap water and groundwater, between 84.2 and 98.9%; surface water, between 71.2 and 81.0%; influent and effluent of wastewater treatment plant (WWTP), between 56.9 and 72.1%. The method detection limits (MDLs) for different water samples were in the range of 26 to 59?ng?l^?1. Real water samples were analysed using the proposed approach to demonstrate the applicability and validation. Negative results were obtained for the tap water and groundwater. However, all the selected cephalosporin antibiotics were identified in the influent and effluent of a local WWTP at ng?l^?1–µg?l^?1 level. In addition, Ceftazidime was found in surface water with a concentration of 0.75–2.60?µg?l^?1. The results indicate that the ‘pseudo-persistent’ contamination of cephalosporin antibiotics in the water environment could not be neglected.     

固相萃取-高效液相色谱法测定地表水中的苯并三唑和苯并噻唑

建立了固相萃取-高效液相色谱分析地表水中苯并噻唑、苯并三唑、5-甲基-苯并三唑、5-氯-苯并三唑及5,6-二甲基-苯并三唑的方法。地表水样品采用HLB固相萃取柱富集净化后,在甲醇-水(55:45, v/v)流动相中用ZORBAX SB-C18色谱柱(250 mm×4.6 mm, 5 μm)分离,紫外检测,外标法定量。结果表明,5种目标化合物在0.064～80 mg/L范围内均呈良好的线性关系,线性相关系数均大于0.9999,仪器检出限为1.9～3.2 μg/L。空白自来水样中的加标回收率为87.8%～125.6%,相对标准偏差(n=3)为0.4%～9.4%。应用该方法测定了大连自来水及辽河入海口水样,在辽河入海口地表水中检出苯并噻唑、苯并三唑、5-甲基-苯并三唑、5-氯-苯并三唑。     

固相萃取-高效液相色谱-可变波长检测法同时测定调味品中甜味剂和人工合成色素

建立了同时测定调味品中糖精钠和合成色素的固相萃取-高效液相色谱(SPE-HPLC)分析方法。样品经石油醚低温去除油脂,聚酰胺固相萃取柱净化和富集,然后进行HPLC分析。采用反相C₁₈色谱柱,以甲醇和0.02 mol/L醋酸铵为流动相进行梯度洗脱,使用可变波长分别在230、510、484和510 nm进行检测。实验结果表明:糖精钠与合成色素的分离效果良好,回收率为88.6%～97.1%,相对标准偏差小于5%;方法检出限均可达到0.05 mg/kg。该方法操作简单,结果准确可靠,重现性好,适用于大批量调味品中甜味剂和人工合成色素的同时检测。     

Determination of sulfadimethoxine in milk with aptamer‐functionalized Fe3O4/graphene oxide as magnetic solid‐phase extraction adsorbent prior to HPLC

An aptamer (Apt) functionalized magnetic material was prepared by covalently link Apt to Fe₃O₄/graphene oxide (Fe₃O₄/GO) composite by 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide hydrochloride and N‐hydroxysuccinimide, and then characterized by FTIR spectroscopy, X‐ray diffraction, and vibration sample magnetometry. The obtained composite of Fe₃O₄/GO/Apt was employed as magnetic solid‐phase extraction adsorbent for the selective preconcentration of sulfadimethoxine prior to analysis by high‐performance liquid chromatography. Under the optimal conditions (sample pH of 4.0, sorbent dosage of 20 mg, extraction time of 3 h, and methanol‐5% acetic acid solution as eluent), a good linear relationship was obtained between the peak area and concentration of sulfadimethoxine in the range of 5.0 to 1500.0 µg/L with correlation coefficient of 0.9997. The limit of detection (S/N = 3) was 3.3 µg/L. The developed method was successfully applied to the analysis of sulfadimethoxine in milk with recoveries in the range of 75.9‐92.3% and relative standard deviations less than 8.1%. The adsorption mechanism of Fe₃O₄/GO/Apt toward sulfadimethoxine was studied through the adsorption kinetics and adsorption isotherms, and the results show that the adsorption process fits well with the pseudo‐second‐order kinetic model and the adsorbate on Fe₃O₄/GO/Apt is multilayer and heterogeneous.     

Dissolvable layered double hydroxide as a sorbent in dispersive micro‐solid phase extraction for the determination of acidic quinolones in honey by HPLC

This study presents a simple and green dispersive micro‐solid phase extraction method for preconcentration of acidic quinolones from honey prior to high performance liquid chromatography determination. A two‐dimensional nanostructured zinc‐aluminum layered double hydroxide was synthesized and used as the sorbent for dispersive micro‐solid phase extraction. Its different characteristics from conventional sorbents is that it is dissolvable in acidic solution (pH < 4). After the extraction, the analyte elution step was omitted and thus the use of organic solvents was avoided. The key parameters influencing the extraction efficiency such as the amount of sorbent, pH of sample solution, vortex time, type and volume of acidic solution were investigated and optimized. The method exhibited low limits of detection (3.0?5.0 ng/g), good linearity (10?2000 ng/g) with coefficients of determinations higher than 0.9991, acceptable precision (RSD<9.1%) and accuracy (RE<5.8%). The proposed method is fast, efficient, eco‐friendly, and suitable for the determination of acidic quinolones in honey samples.     

基于溶胶凝胶技术的在线固相萃取与高效液相色谱联用测定饮用水中的雌激素残留

建立了固相萃取与高效液相色谱在线联用测定水样中3种雌激素(己烯雌酚、己烷雌酚、双烯雌酚)痕量残留的方法。以溶胶凝胶技术合成的聚合物为固相萃取材料,对水样中的雌激素进行萃取富集,考察了样品溶液不同pH、上样流速及洗脱溶剂等条件对合成材料富集效果的影响。结果表明,在优化的条件下,该方法对3种雌激素的检出限(S/N=3)为0.07~0.13 μg/L,样品中的加标回收率为82.31%~99.43%,相对标准偏差(RSD)为1.61%~7.15%。方法简便可靠,适用于饮用水中雌激素的痕量残留检测。