Preparation of a Yb(III)‐Incorporated porous polymer by post‐Coordination: Enhancement of gas adsorption and catalytic activity

We synthesized a Yb(III)‐incorporated microporous polymer (Yb‐ADA) and studied its gas adsorption property and catalytic activity. The adamantane‐based porous polymer (ADA) was obtained from an ethynyl‐functionalized adamantane derivative and 2,5‐dibromoterephthalic acid through Sonogashira–Hagihara cross‐coupling. ADA had two carboxyl groups which were used for Yb(III) coordination under basic conditions. The Brunauer‐Emmett‐Teller (BET) surface area of ADA was 970 m² g^?1. As Yb(III) ions were incorporated into ADA, the surface area of the polymer (Yb‐ADA) was reduced to 885 m² g^?1. However, Yb‐ADA exhibited a significantly enhanced CO₂ adsorption capacity despite the reduction of surface area. The CO₂ uptakes of ADA and Yb‐ADA were 1.56 and 2.36 mmol g^?1 at 298 K, respectively. The H₂ uptake of ADA also increased after coordination with Yb(III) from 1.15 to 1.40 wt % at 77 K. Yb‐ADA showed high catalytic activity in the acetalization of 4‐bromobenzaldehyde and furfural with trimethyl orthoformate and could be reused after recovery without severe loss of activity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5291–5297     

Effect of Functionalized Groups on Gas‐Adsorption Properties: Syntheses of Functionalized Microporous Metal–Organic Frameworks and Their High Gas‐Storage Capacity

The microporous metal–organic framework (MMOF) Zn₄O(L1)₂ ? 9 DMF ? 9 H₂O ( 1‐H ) and its functionalized derivatives Zn₄O(L1‐CH₃)₂ ? 9 DMF ? 9 H₂O ( 2‐CH₃ ) and Zn₄O(L1‐Cl)₂ ? 9 DMF ? 9 H₂O ( 3‐Cl ) have been synthesized and characterized (H₃L1=4‐[N,N‐bis(4‐methylbenzoic acid)amino]benzoic acid, H₃L1‐CH₃=4‐[N,N‐bis(4‐methylbenzoic acid)amino]‐2‐methylbenzoic acid, H₃L1‐Cl=4‐[N,N‐bis(4‐methylbenzoic acid)amino]‐2‐chlorobenzoic acid). Single‐crystal X‐ray diffraction analyses confirmed that the two functionalized MMOFs are isostructural to their parent MMOF, and are twofold interpenetrated three‐dimensional (3D) microporous frameworks. All of the samples possess enduring porosity with Langmuir surface areas over 1950 cm² g^?1. Their pore volumes and surface areas decrease in the order 1‐H > 2‐CH₃ > 3‐Cl . Gas‐adsorption studies show that the H₂ uptakes of these samples are among the highest of the MMOFs (2.37 wt % for 3‐Cl at 77 K and 1 bar), although their structures are interpenetrating. Furthermore, this work reveals that the adsorbate–adsorbent interaction plays a more important role in the gas‐adsorption properties of these samples at low pressure, whereas the effects of the pore volumes and surface areas dominate the gas‐adsorption properties at high pressure.     

Microporous La–Metal–Organic Framework (MOF) with Large Surface Area

A microporous La–metal‐organic framework (MOF) has been synthesized by the reaction of La(NO₃)₃ ? 6 H₂O with a ligand 4,4′,4′′‐s‐triazine‐1,3,5‐triyltri‐p‐aminobenzoate (TATAB) featuring three carboxylate groups. Crystal structure analysis confirms the formation of 3D MOF with hexagonal micropores, a Brunauer–Emmett—Teller (BET) surface area of 1074 m² g^?1 and high thermal and chemical stability. The CO₂ adsorption capacities are 76.8 cm³ g^?1 at 273 K and 34.6 cm³ g^?1 at 293 K, a highest measured CO₂ uptake for a Ln–MOFs.     

Cavitand‐Based Pd‐Pyridyl Coordination Capsules: Guest‐Induced Homo‐ or Heterocapsule Selection and Applications of Homocapsules to the Protection of a Photosensitive Guest and Chiral Capsule Formation

A 2 : 4 mixture of tetrakis[4‐(4‐pyridyl)phenyl]cavitand ( 1 ) or tetrakis[4‐(4‐pyridyl)phenylethynyl]cavitand ( 2 ) and Pd(dppp)(OTf)₂ self‐assembles into a homocapsule { 1 ₂ ? [Pd(dppp)]₄}⁸⁺ ? (TfO^?)₈ ( C1 ) or { 2 ₂ ? [Pd(dppp)]₄}⁸⁺ ? (TfO^?)₈ ( C2 ), respectively, through Pd?Npy coordination bonds. A 1 : 1 : 4 mixture of 1 , 2 , and Pd(dppp)(OTf)₂ produced a mixture of homocapsules C1 , C2 , and a heterocapsule { 1 ? 2 ? [Pd(dppp)]₄}⁸⁺ ? (TfO^?)₈ ( C3 ) in a 1 : 1 : 0.98 mole ratio. Selective formation (self‐sorting) of homocapsules C1 and C2 or heterocapsule C3 was controlled by guest‐induced encapsulation under thermodynamic control. Applications of Pd?Npy coordination capsules with the use of 1 were demonstrated. Capsule C1 serves as a guard nanocontainer for trans‐4,4′‐diacetoxyazobenzene to protect against the trans‐to‐cis photoisomerization by encapsulation. A chiral capsule { 1 ₂ ? [Pd((R)‐BINAP)]₄}⁸⁺ ? (TfO^?)₈ ( C5 ) was also constructed. Capsule C5 induces supramolecular chirality with respect to prochiral 2,2′‐bis(alkoxycarbonyl)‐4,4′‐bis(1‐propynyl)biphenyls by diastereomeric encapsulation through the asymmetric suppression of rotation around the axis of the prochiral biphenyl moiety.     

Colloidal Template Synthesis of Nanomaterials by Using Microporous Organic Nanoparticles: The Case of C@MoS2 Nanoadsorbents

The so‐called colloidal template synthesis has been applied to the preparation of surface‐engineered nanoadsorbents. Colloidal microporous organic network nanotemplates (C‐MONs), which showed a high surface area (611 m² g^?1) and enhanced microporosity, were prepared through the networking of organic building blocks in the presence of poly(vinylpyrrolidone) (PVP). Owing to entrapment of the PVP in networks, the C‐MONs showed good colloidal dispersion in EtOH. MoS₂ precursors were incorporated into the C‐MONs and heat treatment afforded core–shell‐type C@MoS₂ nanoparticles with a diameter of 80 nm, a negative zeta potential (?39.5 mV), a high surface area (508 m² g^?1), and excellent adsorption performance towards cationic dyes (q_max=343.6 and 421.9 mg g^?1 for methylene blue and rhodamine B, respectively).     

Pd‐Catalyzed Ring Assembly by Vinylation and Intramolecular Heck Coupling: A Versatile Strategy Towards Functionalized Azadibenzocyclooctynes

A new modular approach based on Pd‐catalyzed C? C bond formation is presented for the assembly of a benzannulated azocine scaffold, the key intermediate in the synthesis of functionalized azadibenzocyclooctynes (aza‐DIBOs). The intramolecular ring‐closing Heck coupling was investigated by variation of the C? X bond. The reaction rate is limited by the initial oxidative addition step and the regiochemistry strongly depends on the auxiliary phosphine. Under optimized conditions, the 8‐endo regioisomer was obtained in 71 % yield over two steps (with no protecting group chemistry) or in one pot, inclusive of C? N bond formation. The practical generation of the octyne triple bond of a prototypical N‐benzoyl aza‐DIBO, without the need for chromatographic purification, is also described. The structural features, including those of the ring‐strained cyclic octyne, were elucidated by NMR spectroscopy and X‐ray crystallographic analysis. The high reactivity of the N‐benzoyl aza‐DIBO synthesized is demonstrated in a strain‐promoted azide–alkyne cycloaddition reaction with an alkyl azide (k=0.38 M ^?1 s^?1).     

Triazole‐based ligands functionalized silica: Effects of ligand denticity and donors on catalytic oxidation activity of Pd nanoparticles

Triazole‐based ligands, tris (triazolyl)methanol (Htbtm), bis (triazolyl)‐phenylmethanol (Hbtm), and phenyl (pyridin‐2‐yl)(triazolyl)methanol (Hpytm), with differences in ligand denticity (i.e., bidentate and tridentate) and type of N donors (i.e., triazole and pyridine) were functionalized onto a silica support to produce the corresponding SiO₂‐ L ( L  = tbtm, btm, pytm). Subsequent reactions with Pd (CH₃COO)₂ in CH₂Cl₂ yielded Pd/SiO₂‐ L . ICP‐MS reveals that Pd loadings are higher with increased N loadings, resulting in the following trend: Pd/SiO₂‐tbtm (0.83 mmol Pd g^?1) > Pd/SiO₂‐btm (0.65 mmol Pd g^?1) ~ Pd/SiO₂‐pytm (0.63 mmol Pd g^?1). Meanwhile, TEM images of the used Pd/SiO₂‐ L catalysts after the first catalytic cycle show that the mean size of Pd NPs is highest with Pd/SiO₂‐pytm (8.5 ± 1.5 nm), followed by Pd/SiO₂‐tbtm (6.4 ± 1.6 nm) and Pd/SiO₂‐btm (4.8 ± 1.3 nm). Based on TONs, catalytic studies toward aerobic oxidation of benzyl alcohol to benzaldehyde at 60 °C in EtOH showed that Pd/SiO₂‐pytm possessed the most active surface Pd(0) atoms, most likely as a result of more labile properties of the pyridine–triazole ligand compared to tris‐ and bis (triazolyl) analogs. ICP‐MS and TEM analysis of Pd/SiO₂‐btm indicate minimal Pd leaching and similar average Pd NPs sizes after 1^st and 5^th catalytic runs, respectively, confirming that SiO₂‐btm is an efficient Pd NPs stabilizer. The Pd/SiO₂‐btm catalyst was also active toward aerobic oxidation of various benzyl alcohol derivatives in EtOH and could be reused for at least 7 reaction cycles without a significant activity loss.     

Boronate Covalent and Hybrid Organic Frameworks Featuring PIII and P=O Lewis Base Sites

Two covalent organic frameworks comprising Lewis basic P^III centers and Lewis acidic boron atoms were prepared by poly-condensation reactions of newly obtained tris(4-diisopropoxyborylphenyl)phosphine with 2,3,6,7,10,11-hexahydroxytriphenylene and 2,3,6,7-tetrahydroxy-9,10-dimethylanthracene. Obtained materials exhibit significant sorption of dihydrogen (100 cm³ g⁻¹ at 1 bar at 77 K), methane (20 cm³ g⁻¹ at 1 bar at 273 K) and carbon dioxide (50 cm³ g⁻¹ at 1 bar at 273 K). They were exploited as solid-state ligands for coordination of Pd⁰ centers. Alternatively, in a bottom-up approach, boronated phosphine was treated with Pd₂dba₃ and poly-condensated, yielding hybrid materials where the polymer networks are formed by means of covalent boronate linkages and coordination P−Pd bonds. In addition, the analogous materials based on phosphine oxide were synthesized. The DFT calculations on framework–guest interactions revealed that the behavior of adjacent boron and phosphorus/phosphine oxide centers is reminiscent of that found in Frustrated Lewis Pairs and may improve sorption of selected molecules.     

Soluble polynorbornenes with pendant carbazole derivatives as host materials for highly efficient blue phosphorescent organic light‐emitting diodes

We report novel host polymers for a high‐efficiency polymer‐based solution‐processed phosphorescent organic light‐emitting diode with typical blue‐emitting dopant bis(4,6‐difluorophenylpyridinato‐N,C²)iridium(III) picolinate (FIrpic). The host polymers, soluble polynorbornenes with pendant carbazole derivatives, N‐phenyl‐9H‐carbazole ( P1 ), N‐biphenyl‐9H‐carbazole ( P2 ), and 9,9′‐(1,3‐phenylene)bis‐9H‐carbazole (mCP) ( P3 ) are efficiently synthesized by vinyl addition polymerization of norbornene monomers using Pd(II) catalyst in combination with 1‐octene chain transfer agent. The polymers exhibit high thermal stability with high decomposition (T_d5 > 410 °C) and glass transition temperatures (T_g ≈ 268 °C). The HOMO (ca. ?5.5 to ?5.7 eV) and LUMO (ca. ?2.0 to ?2.1 eV) levels with the high triplet energy of about 2.7–3.0 eV suggest that the polymers are suitable for a host material for blue emitters. Among the solution‐processed devices that were fabricated based on the emissive layers containing the P1 ? P3 host doped with various concentrations of FIrpic (7–13 wt %), the best device with P3 host exhibits power efficiency of 3.0 lm W^?1 and external quantum efficiency of 4.0% at a luminance of 1000 cd m^?2 that is outstanding among the polymeric rivals. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

η1‐Allypalladium Complexes with Tridentate PNP’ Ligand for the Assembly of Modified Screen Printed Electrodes: an Electrochemical Study

Specific Pd‐based organometallic complex, in particular the [Pd(η¹‐CH₂? CH=CH₂)(P? N? P’)]BF₄ was used for the assembly of chemically modified Screen Printed Electrodes (SPEs) and their electrochemical reactivity was also investigated. For this purpose potassium ferricyanide, hexaammineruthenium(III) chloride, sodium hexachloroiridate‐(III) hydrate, ascorbic acid (AA), uric acid (UA), acetaminophen (Ac), guanine (G) and adenine (A) were used to study the electron‐transfer processes, which occurred at modified SPEs, fabricated by using the [Pd(η¹‐CH₂? CH=CH₂)(P? N? P’)]BF₄, applying the drop casting procedure. Interesting results were obtained in the case of the guanine (G) quantitative detection, especially in terms of a wide range of concentration (2.5–40 nM), an high sensitivity (of 49.0 A M^?1 cm^?2), a low detection limit (LOD=1.0 nM) and a fast response time (of t=2 s). The intra‐electrode reproducibility (RSD%) was <1 % for the same SPE used for each point of the calibration plot. The inter‐electrode reproducibility (RSD%), estimated by using different SPEs for each single point of the quantitative calibration graph, ranging from 5 to 10 %, better than that exhibited by other different chemical sensors, described in literature, and reported in this work for comparison. In addition, the high selectivity of the chemically modified sensors toward the oxidation of guanine, exhibited in presence of a mixture of G+A, in the same electrochemical bath solution, could be related to the different electro‐catalytic mechanisms, as demonstrated by the XPS study. This chemical sensor prototype could be very promising for bio‐medicine applications.     

Metal Microporous Aromatic Polymers with Improved Performance for Small Gas Storage

A novel metal‐doping strategy was developed for the construction of iron‐decorated microporous aromatic polymers with high small‐gas‐uptake capacities. Cost‐effective ferrocene‐functionalized microporous aromatic polymers (FMAPs) were constructed by a one‐step Friedel–Crafts reaction of ferrocene and s‐triazine monomers. The introduction of ferrocene endows the microporous polymers with a regular and homogenous dispersion of iron, which avoids the slow reunion that is usually encountered in previously reported metal‐doping procedures, permitting a strong interaction between the porous solid and guest gases. Compared to ferrocene‐free analogues, FMAP‐1, which has a moderate BET surface area, shows good gas‐adsorption capabilities for H₂ (1.75 wt % at 77 K/1.0 bar), CH₄ (5.5 wt % at 298 K/25.0 bar), and CO₂ (16.9 wt % at 273 K/1.0 bar), as well as a remarkably high ideal adsorbed solution theory CO₂/N₂ selectivity (107 v/v at 273 K/(0–1.0) bar), and high isosteric heats of adsorption of H₂ (16.9 kJ mol^?1) and CO₂ (41.6 kJ mol^?1).     

Cooperative Effects in Catalytic Hydrogenation Regulated by both the Cation and Anion of an Ionic Liquid

The use of transition‐metal nanoparticles/ionic liquid (IL) as a thermoregulated and recyclable catalytic system for hydrogenation has been investigated under mild conditions. The functionalized ionic liquid was composed of poly(ethylene glycol)‐functionalized alkylimidazolium as the cation and tris(meta‐sulfonatophenyl)phosphine ([P(C₆H₄‐m‐SO₃)₃]^3?) as the anion. Ethyl acetate was chosen as the thermomorphic solvent to avoid the use of toxic organic solvents. Due to a cooperative effect regulated by both the cation and anion of the ionic liquid, the nanocatalysts displayed distinguished temperature‐dependent phase behavior and excellent catalytic activity and selectivity, coupled with high stability. In the hydrogenation of α,β‐unsaturated aldehydes, the ionic‐liquid‐stabilized palladium and rhodium nanoparticles exhibited higher selectivity for the hydrogenation of the C?C bonds than commercially available catalysts (Pd/C and Rh/C). We believe that the anion of the ionic liquid, [P(C₆H₄‐m‐SO₃)₃]^3?, plays a role in changing the surrounding electronic characteristics of the nanoparticles through its coordination capacity, whereas the poly(ethylene glycol)‐functionalized alkylimidazolium cation is responsible for the thermomorphic properties of the nanocatalyst in ethyl acetate. The present catalytic systems can be employed for the hydrogenation of a wide range of substrates bearing different functional groups. The catalysts could be easily separated from the products by thermoregulated phase separation and efficiently recycled ten times without significant changes in their catalytic activity.     

Single Crystal to Single Crystal (SC‐to‐SC) Transformation from a Nonporous to Porous Metal–Organic Framework and Its Application Potential in Gas Adsorption and Suzuki Coupling Reaction through Postmodification

A new amino‐functionalized strontium–carboxylate‐based metal–organic framework (MOF) has been synthesized that undergoes single crystal to single crystal (SC‐to‐SC) transformation upon desolvation. Both structures have been characterized by single‐crystal X‐ray analysis. The desolvated structure shows an interesting 3D porous structure with pendent ?NH₂ groups inside the pore wall, whereas the solvated compound possesses a nonporous structure with DMF molecules on the metal centers. The amino group was postmodified through Schiff base condensation by pyridine‐2‐carboxaldehyde and palladium was anchored on that site. The modified framework has been utilized for the Suzuki cross‐coupling reaction. The compound shows high activity towards the C?C cross‐coupling reaction with good yields and turnover frequencies. Gas adsorption studies showed that the desolvated compound had permanent porosity and was microporous in nature with a BET surface area of 2052 m² g^?1. The material also possesses good CO₂ (8 wt %) and H₂ (1.87 wt %) adsorption capabilities.     

Oligomeric Alkoxysilanes with Cagelike Hybrids as Cores: Designed Precursors of Nanohybrid Materials

Well‐defined alkoxysilane oligomers containing a cagelike carbosiloxane core were synthesized and used as novel building blocks for the formation of siloxane‐based hybrid networks. These oligomers were synthesized from the cagelike trimer derived from bis(triethoxysilyl)methane by silylation with mono‐, di‐, and triethoxychlorosilanes ((EtO)_nMe_3?nSiCl, n=1, 2, and 3). Hybrid xerogels were prepared by hydrolysis and polycondensation of these oligomers under acidic conditions. The structures of the products varied depending on the number of alkoxy groups (n). When n=2 and 3, microporous xerogels (BET surface areas of 820 and 510 m² g^?1, respectively) were obtained, whereas a nonporous xerogel was obtained when n=1. ²⁹Si NMR spectroscopic analysis suggested that partial rearrangement of the siloxane networks, which accompanied the cleavage of the Si–O–Si linkages, occurred during the polycondensation processes. By using an amphiphilic triblock copolymer surfactant as a structure‐directing agent, hybrid thin films with a 2D hexagonal mesostructure were obtained when n=2 and 3. These results provide important insight into the rational synthesis of molecularly designed hybrid materials by sol–gel chemistry.     

Enhanced properties of photovoltaic devices tailored with novel supramolecular structures based on reduced graphene oxide nanosheets grafted/functionalized with thiophenic materials

For verifying the influence of donor–acceptor supramolecules on photovoltaic properties, different hybrids were designed and used in organic solar cells. In this respect, reduced graphene oxide (rGO) was functionalization with 2‐thiophene acetic acid (rGO‐f‐TAA) and grafted with poly(3‐dodecylthiophene) (rGO‐g‐PDDT) and poly(3‐thiophene ethanol) (rGO‐g‐PTEt) to manipulate orientation of poly(3‐hexylthiophene) (P3HT) assemblies. Face‐on, edge‐on, and flat‐on orientations were detected for assembled P3HTs on rGO and its functionalized and grafted derivatives, respectively. Alteration of P3HT orientation from face‐on to flat‐on enhanced current density (J _sc), fill factor (FF), and power conversion efficiency (PCE) and thus J _sc = 7.11 mA cm^?2, FF = 47%, and PCE = 2.14% were acquired. By adding phenyl‐C71‐butyric acid methyl ester (PC71BM) to active layers composed of pre‐designed P3HT/rGO, P3HT/rGO‐f‐TAA, P3HT/rGO‐g‐PDDT, and P3HT/rGO‐g‐PTEt hybrids, photovoltaic characteristics further improved, demonstrating that supramolecules appropriately mediated in P3HT:PC71BM solar cells. Phase separation was more intensified in best‐performing photovoltaic systems. Larger P3HT crystals assembled onto grafted rGOs (95–143 nm) may have acted as convenient templates for the larger and more intensified phase separation in P3HT:PCBM films. The best performances were reached for P3HT:P3HT/rGO‐g‐PDDT:PCBM (J _sc = 9.45 mA cm^?2, FF = 54%, and PCE = 3.16%) and P3HT:P3HT/rGO‐g‐PTEt:PCBM (J _sc = 9.32 mA cm^?2, FF = 53%, and PCE = 3.11%) photovoltaic systems. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1877–1889     

Tunable and Specific Formation of C@NiCoP Peapods with Enhanced HER Activity and Lithium Storage Performance

The superior properties of nanomaterials with a special structure can provide prospects for highly efficient water splitting and lithium storage. Herein, we fabricated a series of peapodlike C@Ni_2?xCo_xP (x≤1) nanocomposites by an anion‐exchange pathway. The experimental results indicated that the HER activity of C@Ni_2?xCo_xP catalyst is strongly related to the Co/Ni ratio, and the C@NiCoP got the highest HER activity with low onset potential of ～45 mV, small Tafel slope of ～43 mV dec^?1, large exchange current density of 0.21 mA cm^?2, and high long‐term durability (60 h) in 0.5 m H₂SO₄ solutions. Equally importantly, as an anode electrode for lithium batteries, this peapodlike C@NiCoP nanocomposite gives excellent charge–discharge properties (e.g., specific capacity of 670 mAh g^?1 at 0.2 A g^?1 after 350 cycles, and a reversible capacity of 405 mAh g^?1 at a high current rate of 10 A g^?1). The outstanding performance of C@NiCoP in HER and LIBs could be attributed to the synergistic effect of the rational design of peapodlike nanostructures and the introduction of Co element.     

Synthesis,Interionic Structure,and Reactivity toward CO and p‐Methylstyrene of Palladacyclic Compounds Bearing α‐Diimine Ligands

Palladacyclic compounds [Pd(C₆H₄(C₆H₅C?O)C?N? R)(N? N)] [X] (R = Et, ⁱPr, 2,6‐ⁱPr₂C₆H₃; N? N = bpy = 2,2′‐bipyridine, or 1,4‐(o,o′‐dialkylaryl)‐1,4‐diazabuta‐1,3‐dienes; [X]^? = [BF₄]^? or [PF₆]^?) were synthesized from the dimers [{Pd(C₆H₄(C₆H₅C?O)C?N? R)(μ‐Cl)}₂] and N? N ligands. Their interionic structure in CD₂Cl₂ was determined by means of ¹⁹F,¹H‐HOESY experiments and compared with that in the solid state derived from X‐ray single‐crystal studies. [Pd(C₆H₄(C₆H₅C?O)C?N? R)(N? N)] [X] complexes were found to copolymerize CO and p‐methylstyrene affording syndiotactic or isotactic copolymers when bpy or 1,4‐(o,o′‐dimethylaryl)‐1,4‐diazabuta‐1,3‐dienes were used, respectively. The reactions with CO and p‐methylstyrene of the bpy derivatives were investigated. Two intermediates derived from a single and a double insertion of CO into the Pd? C bonds were isolated and completely characterized in solution.     

Pd/CNT Catalysts for Glycerol Electro‐oxidation: Effect of Pd Loading on Production of Valuable Chemical Products

Glycerol (C₃H₈O₃), a waste product of biodiesel, is considered as a suitable substrate for electro‐oxidation process to generate high value‐added products. A suitable active catalyst could improve the yield of desirable organic compounds from electro‐oxidation of glycerol. In this work, palladium nanoparticles supported over activated multi‐walled carbon nanotubes (MWCNTs) with varying loadings of 5 %–40 % were prepared using chemical reduction method and used to study their potential for electro‐oxidation of glycerol to produce various high value‐added products. The catalysts were characterized by different physicochemical methods, such as X‐ray diffraction (XRD), N₂ adsorption‐desorption, and Transmission electron microscopy (TEM), whereas the electro‐oxidation activity of the catalysts was analysed using cyclic voltammetry (CV) and chronoamperometry (CA), and the products were identified by high performance liquid chromatography (HPLC). The electrochemical surface area (S_ESA) and mass activity (MA) were increased from 176.98 m² g^?1 to 282.29 m² g^?1 and 12.22 mA mg^?1 to 49.53 mA mg^?1 by increasing the Pd‐loading from 5 % to 20 %, respectively. While the further increase to 40 % Pd loading, the S_ESA and MA values decreased to 231.45 m² g^?1 and 47.63 mA mg^?1respectively. The results found that the optimum 20 % Pd‐loading showed the excellent electrochemical properties due to uniform distribution of Pd‐metal particles over MWCNTs. High performance liquid chromatography (HPLC) showed the tartronic acid, glyceric acid and glyceraldehyde as dominant products. Mechanism of the reaction has also been proposed based on product distribution.     

Template‐free anion‐controlled synthesis of Pd (II) nano‐aggregates for the antifouling polymerization of CO and ethylene

The reaction of [(domppp) Pd (OAc)₂] [domppp = 1,3‐bis (di‐o‐methoxyphenylphosphino)propane] and imidazolium‐functionalized carboxylic acids containing various anions (Br^?, PF₆^?, SbF₆^? and BF₄^?) resulted in the formation of nano‐sized Pd (II) aggregates under template‐free conditions. The rate of formation of aggregates can be modulated by changing the anion, affecting the rate of polymerization of CO and olefins without fouling. Herein, we describe the analysis of Pd (II) catalysts by dynamic light scattering, atomic force microscopy, X‐ray photoelectron spectroscopy and X‐ray crystallography, and co‐ and terpolymerization results including the catalytic activity, and bulk density and molecular weight of polymers.