表面修饰引发的ZnO纳米棒阵列膜的超疏水性

润湿性是固体表面的重要性质之一 ,它受控于固体表面自由能和表面粗糙度的大小 ,一般可用液体在固体表面接触角的大小来衡量 .由于水与超疏水表面 (水与固体表面的接触角大于 1 5 0°的表面 )的接触面积很小 ,通过水所发生的化学发应和化学键的形成受到限制 ,使这种表面具有防水、防污染和防氧化等多种功能 ,因而备受人们的关注 [1～ 6 ] .作为宽禁带半导体材料 ,Zn O以其独特的光电和催化等性质在短波激光器、气体传感器、高效催化剂、太阳能电池等方面具有广阔的应用前景 .表面润湿性的研究对于将 Zn O用于各种器件非常重要 .Pesika等 […     

阵列聚合物纳米柱膜的超疏水性研究

浸润性(又称润湿性,Wettability)是固体表面的一个重要特征,它主要由表面化学组成和表面的几何结构两方面控制^[1～5].近年来,超疏水性固体表面由于在防雪、防污染、抗氧化以及防止电流等方面都有非常广阔的应用前景,引起了人们的极大关注[6～11].     

纳米钛薄膜的XPS研究

用 XPS分析了三种纳米钛薄膜表面和经 Ar 溅射后内部碳、氧、氮、钛等的含量和化学态。发现三种薄膜表面碳、氧含量完全一致 ,碳为石墨态 ,氧为吸附态的水。薄膜内部碳、氧、氮的化学态主要为 Ti C、Ti O2 、Ti N。随着分析深度的增加 ,薄膜内金属钛的原子百分比浓度不断增加并逐渐趋于恒定。镀膜时真空度的提高有利于减少碳、氧、氮的污染。Ar 溅射所镀的膜与电子枪所镀的膜相比 ,晶粒尺寸小 ,在表面至浅表层内氧的含量有明显差异。     

表面修饰二氧化锡纳米微晶的制备与表征

制备了硅烷偶联剂KH-570表面修饰的SnO2纳米微晶，通过FT-IR、XPS、TEM和TG-DTA对其结构和表面特性进行表征和研究. FT-IR和XPS分析结果确证了KH-570与SnO2表面是以化学键合或物理吸附方式相结合,粒子表面存在酯基等有机官能团的红外吸收特征；观测到KH-570中Si原子的Si2s和Si2p谱线. TEM分析表明，表面修饰反应增强了SnO2纳米微晶的疏水性和分散性.由XPS和TG的实测数据探讨了纳米粒子具有较低包覆量的可能原因.     

Gd-Ba-Cu-O超导膜的XPS研究

用XPS对不同凡的Gd-Ba-Cu-O超导膜做了定量、角分布、成象和离子剥蚀纵深分析．结果表明：样品表面都存在Ba富集和Gd短缺,表面原子微观分布不均匀;表面和纵深都存在含C物质污染;与Tc≥87K的样品比较,Tc≤77K的膜表面对应于非超导相的Ba和O原子浓度最高,膜的纵深处的原子组成仍偏离化学计量,而且膜表面和纵深处的含C物污染最严重．     

紫外光辐照制备超亲水再生丝素蛋白膜

众多的研究已表明生物材料的表面润湿性(wettability)对于细胞的粘附有重要的影响. 在通过浇铸成膜并辅以乙醇后处理方法制备非水溶性再生丝素蛋白膜的基础上,我们采用紫外光辐照的方法以改变此类丝素蛋白膜的表面特性. 接触角测试的结果显示,随着紫外光照时间的增加,丝素蛋白膜表面与水的接触角逐渐降低,最终可以达到超亲水的状态;表面X射线光电子能谱(XPS)分析表明,这是由于丝素蛋白膜表面亲水性基团(包括羧基和羰基等)的含量随着紫外光照时间的延长而增加所致. 同时我们发现,经紫外光辐照一定时间后,再生丝素蛋白膜的力学性能并没有发生显著的降低. 显然,此类具有较高力学性能且表面亲水性能较好的再生丝素蛋白膜有可能被进一步应用于生物医学领域.     

超疏水性聚二甲基硅氧烷膜的制备及其表面吸附性研究

采用简单的激光刻蚀方法制备了具有类“菜花”状多级结构的粗糙聚二甲基硅氧烷(PDMS)膜, 并用CCD与高敏感性微电力学天平观察和测量PDMS表面对水的吸附情况. 结果表明, 该膜表面具有超疏水性, 同时对水滴具有超低的吸附力. 还对其表面特殊多级结构产生的机理进行了分析, 并探讨了在化学组成和表面结构对超疏水性以及吸附性产生的影响.     

具有微纳米结构超疏水表面润湿性的研究

本文综述了近年来具有微纳米结构超疏水表面的研究进展。介绍了具有微纳米结构超疏水表面的制备方法,表面结构对超疏水性能的影响,周期性结构表面超疏水的条件,超疏水表面接触角滞后以及功能化超疏水表面等方面的研究,探讨了这一领域存在的问题及可能的发展方向。     

柱状结构阵列碳纳米管膜的超疏水性研究

浸润性是固体表面的重要性质之一 .决定固体表面的浸润性的两个主要因素中 ,化学性质是内因 ,而几何结构形貌也是不可缺少的重要因素 .通过改变固体表面的粗糙度可以改变其浸润性 [1～ 5] .通常 ,人们用水接触角的大小来衡量固体表面水的浸润性 ,水与固体表面的接触角大于 1 5     

超疏水性聚苯胺微/纳米结构的合成及防腐蚀性能

以苯胺为单体, 过硫酸铵为氧化剂, 通过改变不同的掺杂剂, 采用"无模板"法合成了具有不同浸润性的聚苯胺微/纳米结构, 并得到超疏水聚苯胺微/纳米结构. 采用红外吸收光谱、 紫外-可见吸收光谱、 X射线衍射及扫描电镜对聚苯胺微/纳米结构及形貌进行了表征, 测定了聚苯胺微/纳米结构的接触角, 并通过Tafel极化曲线和电化学交流阻抗研究了不同疏水性的聚苯胺微/纳米结构在0.1 mol/L H₂SO₄溶液中对碳钢的腐蚀防护作用, 探讨了聚苯胺微/纳米结构的表面浸润性对腐蚀防护性能的影响. 研究结果表明, 随着聚苯胺微/纳米结构疏水性的增强, 对碳钢的腐蚀防护作用增强, 当掺杂剂为全氟辛酸时所制备的超水聚苯胺微/纳米结构表现出最佳的防腐蚀性能(η= 94.70%).     

Preparation and Characterization of Nano-Structured SiO2 Thin Films on Carbon Steel

Nano-structured SiO2 thin films were prepared on the surface of carbon steel for the first time by LPD. The compositions of the films were analyzed by XPS, and the surface morphology of the thin films were observed by AFM. The thin films were constituted by compact particles of SiO2, and there was no Fe in the films. In the process of film forming, the SiO2 colloid particles were deposited or absorbed directly onto the surface of carbon steel substrates that were activated by acid solution containing inhibitor, and corrosion of the substrates was avoided. The nano-structured SiO2 thin films that were prepared had excellent protective efficiency to the carbon.     

Sol-Gel Preparation and Characterization of Ag-TiO2 Nanocomposite Thin Films

Ag-TiO₂ thin films were prepared with a sol-gel route, using titanium isopropoxide and silver nitrate as precursors, at 0.03 and 0.06 Ag/Ti nominal atomic ratios. After drying at 80°C, the films were fired at 300°C and 500°C for 30 min. The films were analysed by X-ray diffraction (XRD) with glancing angle, and X-ray photoelectron spectroscopy (XPS), with depth profiling of the concentration. XPS analysis showed the presence of C and N as impurities in the nanocomposite films. Their concentration decreased with increasing the firing temperature. Chemical state analysis showed that Ag was present in metallic state, except for the very outer layer where it was present as Ag⁺. For the films prepared with a Ag/Ti concentration of 0.06, depth profiling measurements of the film fired at 300°C showed a strong Ag enrichment at the outer surface, while composition remained almost constant within the rest of the film, at 0.019. For the films heated to 500°C, two layers were found, where the Ag/Ti ratios were 0.015 near the surface and 0.026 near the substrate.     

Preparation and Characterization of Nanostructured Ni-TiN Composite Films

Ni-TiN nanocomposite films were produced from a Ni plating bath containing TiN nanopar-ticles by using dc electroplating method. The structure and surface morphology of Ni-TiN composite coatings were analyzed by atom force microscope, X-ray diffraction, and trans-mission electron microscopy. Meanwhile, the anti-corrosion properties, hardness and ther-mostability of Ni-TiN nanocomposite films were also investigated and compared with the traditional polycrystalline Ni coatings. The results show that, compared with the tradi-tional polycrystalline Ni film, Ni-TiN nanocomposite coatings display much better corrosion resistance, higher film hardness, and thermal stability. In addition, the hardness of Ni-TiN nanocomposite coatings decreases slightly with the increase of electroplating current density,which may be due to the synergism of hydrogen evolution and faster nucleation/growth rate of nickel crystallites.     

乙酰化甲壳素膜的制备及表征

本文报道了加入二氯甲烷可使甲壳素的乙酰化反应更顺利进行,并提高了产物的乙酰化度,通过红外、X射线衍射分析、拉伸等方法对乙酰化甲壳素膜的结晶结构和力学性能作了表征和测定。     

Fabrication of Superhydrophobic Surface with Different Metal Films on Aluminum Alloy

A simple technique was developed for the fabrication of a superhydrophobic surface on the aluminum alloy sheets. Different hierarchical structures(Ag, Co, Ni and Zn) were formed on the aluminum surface by the galvanic replacement reactions. After the chemical modification of them with fluorination, the wettability of the surfaces was changed from superhydrophilicity to superhydrophobicity. Scanning electron microscopy(SEM), energy dispersive spectrometry(EDS) and water contact angle measurement were performed to characterize the morphological characteristic, chemical composition and superhydrophobicity of the surfaces. The as-prepared superhydrophobic surfaces showed a water contact angle as high as ca.160° and sliding angle as low as ca.3°. We hope the method to produce superhydrophobic surface can be used in many fields.     

一步法合成聚苯胺/十二烷基苯磺酸钠超疏水复合材料

在阴离子表面活性剂十二烷基苯磺酸钠(SDBS)体系中,采用一步法制得聚苯胺/SDBS超疏水复合材料.利用场发射扫描电子显微镜(FESEM)观察产物形貌并测定其元素组成.通过傅里叶变换红外光谱仪、紫外-可见光谱仪、X射线衍射等对其结构进行表征,用视频接触角测量仪测定材料的亲疏水性.考察SDBS浓度和溶液酸度对产物形貌及疏水性能的影响,探讨疏水机理.结果表明:在pH=1-9,SDBS浓度大于0.016 mol?L-1条件下,所制备复合材料的水接触角大于150°,SDBS掺杂使得苯胺单体的转化率高达98%.两亲分子SDBS亲水磺酸基与聚苯胺主链上的亚胺基不仅存在静电引力,而且能形成磺酰胺键,聚苯胺主链间又以氢键相互连接,SDBS分子的疏水烃基有序排列朝向聚苯胺主链外侧,从而组装形成具有微纳结构的聚苯胺/SDBS超疏水复合材料.本文结果有利于更好地理解聚苯胺/SDBS超疏水性复合材料的形成机理,对超疏水材料的设计提供新思路.     

Preparation of Nanostructured Magnetic Films by the Plasma Jet Technique

Summary.  Magnetic films were prepared by the plasma jet technique from Fe, mumetal, and Fe/Hf or Fe/Ta nozzles. Two different plasma jet systems with different vacuum pumps were used to compare the quality of the produced films. The films prepared from a Fe nozzle in the two different equipments shows that oxygen in the residual atmosphere of the low vacuum reactor leads mainly to the formation of iron oxides. The Fe and mumetal films prepared in the high vacuum system contain only a very small amount of oxygen, as proved by chemical analysis and ferromagnetic resonance. The mumetal film, moreover, shows good soft magnetic properties and low magnetic damping. For the reactive plasma jet deposition of nanogranular Fe–Hf–O and Fe–Ta–O films, the low vacuum system was used. The films with higher oxygen content exhibit tunneling-type conductivity. In some films, superparamagnetic behaviour and spin-dependent tunneling magnetoresistance were observed. Received October 5, 2001. Accepted November 22, 2001     

喷雾热蒸发碳膜用于锂离子电池负极的研究

以有机热解碳（石墨）为原料,用喷雾热蒸发法制备了用于锂离子电池负极的碳膜,用循环伏安法和恒电流充放电法测试了所获碳膜的电化学性能,测试结果表明,在第一循环周期中存在一个还原峰,该还原峰对应在电极表面形成固体电解质中间相膜;当充放电电流大小适合时,容量和Ｘ值都较大。基于这些实验结果,可以认为所获得的碳膜作用负极以相对测试其他正极材料电化学性能。     

溶剂散逸自组装制备超疏水针垫阵列膜

利用溶剂散逸自组装方法,以聚苯乙烯、聚十二烷基丙烯酰胺-6-丙烯酰胺基己酸（CAP）和三氯甲烷为原料,在平滑的固体基质上制备了有序多孔膜,该膜上下表面可在外力作用下发生分离,得到具有微米级超疏水针垫阵列膜。 结果表明,制得的聚苯乙烯膜具备超疏水性质,与水接触角达158°。     

石墨烯/碳纳米管复合薄膜的制备进展

石墨烯/碳纳米管复合材料具有石墨烯和碳纳米管的共同特性,它弥补了石墨烯不连续和碳纳米管网存在间隙这两方面缺点。 本文探讨了石墨烯/碳纳米管复合薄膜的制备新进展,阐述了利用自组装合成、非原位合成以及非化学合成等方法制备厚度薄、强度高和比电容高等特点的石墨烯/碳纳米管复合薄膜的方法,对石墨烯/碳纳米管复合薄膜在传感器、锂电池和超级电容器等方面的应用前景进行了展望。