Droplet production from disintegrating bubbles at water surfaces. Single vs. multiple bubbles

We experimentally determine the droplet production rate at a water surface where either single or multiple bubbles (bubbly flow) with similar mean diameters disintegrate and produce film and jet droplets. A detailed assessment of film drop production from bubbly flow is important, since most presently used correlations are based on single-bubble measurements. Moreover, jet drops––even though they contain a much larger fluid volume––are de-entrained into the water surface in most technical and geophysical applications. Detailed phase Doppler anemometry (PDA) measurements are performed in the vicinity of the water surface with long sampling times. For a considered mean diameter of approximately 3 mm, the size distribution of the non spherical bubbles is determined from photographic images. From single-bubble measurements we find, consistent with literature data, a narrow size distribution of the jet drops with a mean diameter of 477 μm. For bubbly flow, the maximum is shifted to somewhat smaller jet drop diameters (425 μm) and the production of film droplets increases significantly. We relate this increase to the coalescence of bubbles prior to their disintegration at the surface. Our results therefore show that for a fixed bubble size and gas flow rate the number of film drops entrained from a bubbly flow is underestimated, if the estimate is based on single-bubble data.     

水下爆炸气泡射流载荷阵列测量技术探索

水下爆炸气泡射流载荷测量目前存在两个难点:（1）气泡射流载荷是非均匀的面载荷,但其作用半径仅为气泡最大半径的1/10,限于传感器尺寸及安装空间,敏感元密度较低,难以准确获取气泡射流载荷空间分布规律;（2）气泡射流载荷测量时传感器所处的力学环境非常复杂,传感器容易损坏,导致无法测得完整时程。因此现有测量手段难以获取气泡射流载荷的时空分布特性。鉴于此,设计了一种阵列传感器,在一张PVDF（聚偏氟乙烯）压电薄膜上采用特殊工艺加工多个小型敏感元,敏感元尺寸为5 mm×5 mm,呈8×8矩阵排列,敏感元密度≥1 cm?2,同时在揭示传感器损坏机理的基础上设计了传感器防护装置。在小型观测水槽内开展了小当量炸药水下爆炸试验,采用阵列传感器测量获取了气泡射流载荷的时空分布特性。研究结果表明:（1）设计的防护装置可保证传感器在气泡射流载荷测量过程中不损坏;（2）气泡射流载荷中心最大,向四周逐渐减小,中心处气泡射流载荷峰压约35.6 MPa,约为冲击波峰压的1.16倍。建立的阵列测量技术可为水下爆炸气泡射流的深入研究提供技术支撑。     

Crown behavior and bubble entrainment during a drop impact on a liquid film

Physical and mathematical models are established to simulate a single liquid drop impinging onto a liquid film using the coupled level set and volume of fluid method. The crown liquid sheet after impact is obtained, which coincides well with the experimental results in literatures. Influence of Weber number, Reynolds number and the dimensionless film thickness on the crown diameter and height is discussed quantitatively. Results indicate that the crown diameter is independent of the two non-dimensional numbers, while it can be increased by reducing the dimensionless film thickness. The crown height increases with the increasing of Weber number, but Reynolds number has small effect on it. Mechanism of the jet formation process is revealed by analyzing pressure distribution and velocity field in the liquid. It is found that both pressure difference in the neck region and velocity discontinuity can greatly affect the jet formation. Besides, the bubble entrainment phenomenon during a liquid drop impact on a liquid film is successfully captured with this numerical method. It is found that the increase in both impact Weber number and the drop diameter contributes to the emerging of bubble rings.     

Cavity and flow measurements of reproducible bubble entrainment following drop impacts

High-speed motion pictures of air–water interface dynamics of drop impacts that reproducibly make bubbles are presented. The pictures show previously unobserved details of the phenomenon. Measurements are compared with available computational methods. Experimental and numerical results agree with each other on the overall shape of the interface and the occurrence of bubble detachment. Measurements, however, show that the cavity depth stagnates before bubble entrapment. This behavior is not predicted by simulation. Also discussed are the presence of a jet that strikes the new bubble after formation and the possible effect of droplet surface oscillations on bubble entrainment. Received: 25 April 2000 / Accepted: 26 April 2001     

Three-dimensional bubble field resolution using synthetic aperture imaging: application to a plunging jet

A methodology for resolving three-dimensional (3D) bubble fields using 3D synthetic aperture imaging (SA imaging) is developed and applied to the bubbly flows induced by a turbulent circular plunging jet. 3D SA imaging involves capturing entirely in-focus images in an array of cameras with multiple viewpoints, then reprojecting the images into the measurement volume and combining them post capture. The result is a stack of synthetically refocused images that span the measurement volume with each refocused image having a narrow focus on a particular plane. In this paper, bubble shadow images are captured by projecting diffuse backlight onto the measurement volume. 3D SA imaging is ideally suited to investigate optically dense multiphase flows due to the ability to reconstruct volumes that contain partial occlusions. Instantaneous bubble sizes and locations in the plunging jet bubble fields are extracted from the volumes using two feature extraction algorithms and presented for various jet heights. The data are compared with existing literature on bubble penetration depth and size distributions. A scaling law for the integrated air concentration as a function of depth below the free-surface is proposed. Coupled with scaling laws for a parameter describing the radius of the bubble cone and radial concentration profiles, this new scaling law can be used to determine the entire air concentration profile given a minimal number of single-point measurements.     

Bubble jet flow interaction during pool boiling of subcooled water on horizontal thin wires

Both visual experiments and numerical analyses were conducted to investigate the interaction between bubble jet flows during pool boiling of subcooled water on horizontal thin wires. The bubble jet flows nearby attracted each other, and they can combine into one jet flow under strong interaction. As the adjacent bubble departs, the bubble jet flow would experience an unsteady evolution process with the jet flow interaction weakening. Since the unsymmetrical thermocapillary force at the bubble interface was induced by the adjacent bubble as a cold source, the bubble jet flow would trend to the adjacent bubble, and the mechanism based on thermocapillary force and cold source can explain the bubble jet flow interaction very well. The steady bubble jet flow interaction phenomena were further simulated by laminar model, and the calculated jet flow interaction phenomena were in a good agreement with the experimental results.     

Spark-generated bubble collapse near or inside a circular aperture and the ensuing vortex ring and droplet formation

This paper aims to study the oscillation of a sparkgenerated submerged bubble located near or inside a circular aperture made in a flat plate using high-speed visualization technique. In the case of a bubble oscillating near an aperture the initial free surface of the water was set at the bottom surface of the plate. The effects of aperture size and bubblefree surface distance on the bubble behavior as well as on the ensuing droplet dynamics are investigated. It was found that the direction of the bubble reentrant jet was towards the aperture or away from it respectively when the normalized aperture size was smaller or greater than a certain critical value. In addition, a toroidal vortex ring was observed to form, which rotated inwards as it moved away from the aperture. It was also found that if the bubble was incepted at a distance sufficiently away from a supercritical size aperture a single droplet could be produced. In the case of a bub- ble initiated in the middle of a circular aperture submerged just beneath the water free surface, the bubble was found to take the shape of an ellipsoid during its expansion. Then a reentrant jet was initiated and pierced the bubble from its top side.     

Single cavitation bubble generation and observation of the bubble collapse flow induced by a pressure wave

This study utilizes a U-shape platform device to generate a single cavitation bubble for a detailed analysis of the flow field characteristics and the cause of the counter jet during the process of bubble collapse caused by sending a pressure wave. A high speed camera is used to record the flow field of the bubble collapse at different distances from a solid boundary. It is found that a Kelvin–Helmholtz vortex is formed when a liquid jet penetrates the bubble surface after the bubble is compressed and deformed. If the bubble center to the solid boundary is within one to three times the bubble’s radius, a stagnation ring will form on the boundary when impinged by the liquid jet. The fluid inside the stagnation ring will be squeezed toward the center of the ring to form a counter jet after the bubble collapses. At the critical position, where the bubble center from the solid boundary is about three times the bubble’s radius, the bubble collapse flow will vary. Depending on the strengths of the pressure waves applied, the collapse can produce a Kelvin–Helmholtz vortex, the Richtmyer–Meshkov instability, or the generation of a counter jet flow. If the bubble surface is in contact with the solid boundary, the liquid jet can only move inside-out without producing the stagnation ring and the counter jet; thus, the bubble collapses along the radial direction. The complex phenomenon of cavitation bubble collapse flows is clearly manifested in this study.     

水中高压脉动气泡水射流形成机理及载荷特性研究

具有脉动特性的气泡(如水下爆炸气泡、螺旋桨空泡和气枪气泡)动力学行为很大程度上取决于其边界条件. 实验已证实,近自由液面气泡在坍塌过程中常常产生背离自由液面的水射流现象,而近刚性边界气泡在坍塌阶段产生朝向壁面的高速水射流,严重威胁水中结构的局部强度. 前人基于 Rayleigh-Plesset 气泡理论和 “Bjerknes” 力来预测气泡射流方向,然而理论方法难以透彻的揭示气泡射流的初生、发展和砰击过程中丰富的力学机理. 本文首先采用水下高压放电技术产生气泡,并通过高速摄影对不同边界条件下气泡的运动特性进行实验研究. 然后,采用边界积分法模拟气泡非球状坍塌过程. 研究表明,边界条件改变了气泡周围的流场压力梯度方向,进而影响气泡射流初生位置;射流在发展阶段,气泡附近流场的局部高压区和射流之间存在“正反馈效应”,从而揭示了气泡射流速度在短时间内即可增加到百米每秒的力学机理. 射流砰击会在流场中造成局部高压区,随着气泡回弹,射流速度和砰击压力逐渐减小. 本文还探讨了无量纲距离参数对气泡运动及射流砰击载荷的影响,旨为近场水下爆炸等相关领域提供参考.      

Jet formation in shock-heavy gas bubble interaction

The influences of the acoustic impedance and shock strength on the jet formation in shock-heavy gas bubble interaction are numerically studied in this work. The process of a shock interacting with a krypton or a SF 6 bubble is studied by the numerical method VAS2D. As a validation, the experiments of a SF 6 bubble accelerated by a planar shock were performed. The results indicate that, due to the mismatch of acoustic impedance, the way of jet formation in heavy gas bubble with different species is diversified under the same initial condition. With respect to the same bubble, the manner of jet formation is also distinctly different under different shock strengths. The disparities of the acoustic impedance result in different effects of shock focusing in the bubble, and different behaviors of shock wave inside and outside the bubble. The analyses of the wave pattern and the pressure variation indicate that the jet formation is closely associated with the pressure perturbation. Moreover, the analysis of the vorticity deposition, and comparisons of circulation and baroclinic torque show that the baroclinic vorticity also contributes to the jet formation. It is concluded that the pressure perturbation and baroclinic vorticity deposition are the two dominant factors for the jet formation in shock-heavy gas bubble interaction.     

Formation of the finely dispersed gas phase in upward and downward fluid flows

The influence of the fluid and gas flow rate parameters on the diameter of bubbles separating from a single capillary immersed in a fluid flow in a channel of 1×1 cm cross-section is investigated. The dependences of the mean bubble diameter on the fluid velocity and the gas flow rate through the capillary are obtained. The frequency of the bubble detachment from the capillary is estimated. It is shown that the histogram of the bubble size distribution changes qualitatively with the excess of a certain critical bubble detachment frequency, which is associated with the transition from the discrete to jet mode of detachment.     

近场水下爆炸气泡脉动及水射流的实验与数值模拟研究

海上作战时,近场水下爆炸形成的水射流能造成水面舰船结构的严重局部毁伤。为了研究近场爆炸时舰船底部水射流的形成机理及规律,开展了TNT当量2.5 g的炸药在固支方板底部不同爆距下起爆的水下爆炸实验。结果表明,气泡坍塌形成水射流的过程随着爆距的增加由吸附式向非吸附式转化。接着,基于ABAQUS软件采用CEL方法开展了系列数值模拟,结果表明:爆距在0.821～0.867倍最大气泡半径时,存在吸附式射流向非吸附式射流转化的临界点;固支方板加快了气泡坍塌的进程,炸药与钢板间的距离越小则射流形成的时间越早;射流形成过程中最大速度和射流击中钢板时速度均随着爆距的增大先增大后减小,并在临界点附近达到最大值,射流速度最大可达621 m/s,射流击中钢板时速度最大可达269 m/s。最后,给出了射流开始形成时间、射流最大速度、射流最大速度出现时间、射流击中钢板速度和射流击中钢板时间与距离参数的函数关系式。     

水下爆炸中气泡射流壁压特性实验研究

水下爆炸气泡射流载荷是中近场水下爆炸壁压载荷的重要组成部分, 将水下爆炸气泡射流简化为一段高速水柱来研究水下爆炸气泡射流载荷特性是研究水下爆炸气泡射流载荷的主要手段。本文基于腔内爆炸提出了一种新的高速水射流实验方法,并给出了实验装置设计、实验方法以及实验系统。基于实验系统,开展了不同工况下高速水射流的实验研究,研究了腔口位置、腔深对水射流形态的影响,并对水射流的形态形成因素进行了分析。使用压电型壁压传感器测得了水射流冲击壁压,给出了水射流冲击壁压的特性及其特点。实验结果表明:腔口位置与腔深是影响水射流端面形态的重要因素;生成的高速水射流冲击壁压峰值满足水锤理论。基于腔内爆炸的高速水射流实验方法能够应用于包括水下爆炸气泡射流在内的高速水射流形态、壁压特性的研究。     

Vortex ring modelling of toroidal bubbles

During the collapse of a bubble near a surface, a high-speed liquid jet often forms and subsequently impacts upon the opposite bubble surface. The jet impact transforms the originally singly-connected bubble to a toroidal bubble, and generates circulation in the flow around it. A toroidal bubble simulation is presented by introducing a vortex ring seeded inside the bubble torus to account for the circulation. The velocity potential is then decomposed into the potential of the vortex ring and a remnant potential. Because the remnant potential is continuous and satisfies the Laplace equation, it can be modelled by the boundary-integral method, and this circumvents an explicit domain cut and associated numerical treatment. The method is applied to study the collapse of gas bubbles in the vicinity of a rigid wall. Good agreement is found with the results of Best (J. Fluid Mech. 251 79–107, 1993), obtained by a domain cut method. Examination of the pressure impulse on the wall during jet impact indicates that the high-speed liquid jet has a significant potential for causing damage to a surface. There appears to be an optimal initial distance where the liquid jet is most damaging.     

环形喷管喷口气泡演化的实验研究

水下气泡的发展演化及气泡动力学行为是气液两相动力学的基础理论与水下射流应用的重要基础. 环形喷管/喷口形成的气泡及气体射流具有其不同于圆孔实心射流的特殊表现与规律机制,随着同心筒破水发射等特殊应用的出现,环形喷口气体射流/泡流的基础现象观测和机制分析成为迫切的需求. 基于环形喷管的设计和水下射流条件的分析,设计建立了一套环形喷管水箱实验系统,对水下环形喷管喷口气泡发展演化过程进行了初步的实验研究. 为观测研究气体通过环形喷管气泡生长发展过程,在较低压力、较低流速下,采用高速摄影仪记录气泡生长及发展演化过程. 结合对气泡发展演化过程的图像处理与分析,研究分析了环形喷口气泡形成区制、气泡生长过程形态发展特点、以及气泡形成时间及气泡体积变化特点. 研究表明:在本实验气体流量范围内(50.8~237.3 dm3/min),环形喷口气泡发展演化过程呈现较为明显的三周期区制,前泡尾流影响是环形气泡呈三周期区制的主要原因;不同周期内的气泡形成时间具有较稳定规律,并受到流量影响;气泡生长过程中有较为明显的下沉、回升特征;气泡表面张力、液体惯性与流动的共同作用,造成了典型的气泡顶部坍塌现象.      

Influence of gas injection on phase inversion in an oil–water flow through a vertical tube

An experimental study has been made of the influence of gas injection on the phase inversion between oil and water flowing through a vertical tube. Particular attention was paid to the influence on the critical concentration of oil and water where phase inversion occurs and on the pressure drop increase over the tube during phase inversion. By using different types of gas injectors also the influence of the bubble size of the injected gas on the phase inversion was studied. It was found that gas injection does not significantly change the critical concentration, but the influence on the pressure drop is considerable. For mixture velocities larger than 1 m/s, the pressure drop over the tube increases with decreasing bubble size and at inversion can become even larger than the pressure drop during the flow of oil and water without gas injection.     

Experimental investigation of the interaction between a pulsating bubble and a rigid cylinder

In this paper, the behavior of a bubble near a rigid cylinder is studied experimentally as the positions of bubble induction change, and several cylinders with different diameters are used in the experiment. The main results are as follows. The behavior of a bubble near a rigid cylinder is distinct from that near a rigid plate. When the cylinders are laid in deep water, there will occur three kinds of typical bubble shapes as the distance between bubble and cylinder increases. And the bubble shapes are different as the diameter of cylinder varies. When the cylinders are laid near a free surface, the behaviors of bubble near cylinders with different diameters are similar. For a certain distance between bubble and free surface, as the distance between bubble and cylinder increases, "double jet", "inclined jet" and "downward jet" will take place successively.     

舱段结构在气泡射流作用下的毁伤效果

为研究水下爆炸气泡载荷对船舶局部结构的毁伤效果,设计建造了实尺度舱段模型,并进行水下 爆炸实验,测量了水中压力、气泡脉动周期、舱段外板结构的动应变与塑性变形。分析了不同冲击因子作用下 舱段结构的动态响应,并结合水中压力测量结果,探讨了气泡射流的成因。在此基础之上,分析了气泡射流载 荷的影响范围以及外板在不同载荷作用下的毁伤模式。实验结果表明,相比冲击波载荷,在某些情况下射流 冲击载荷引起的结构响应更剧烈,毁伤效果更严重,因此在中近场水下爆炸作用下,气泡射流冲击载荷对船体 结构的影响不能忽视。     

两空泡运动特性研究

本文应用边界方法研究了两个相邻空泡的运动特性,得到了空泡的演化规律,以及空泡溃灭时的射流速度与溃灭时间的变化趋势,对于两个空泡之间的距离和半径比的影响进行了讨论。计算结果表明：不同大小的空泡在一起时则小泡会先溃灭,且人泡的存在时间与两泡的半径比成正比;大泡对小泡来说其作用相当于－固壁面,小泡会形成－指向大泡的溃灭射流。相同大小的空泡在一起溃灭时,会同时形成指向中间的射 流,与单空泡在固壁面附近的溃     

The Art, Craft and Science of Modelling Jet Impact in a Collapsing Cavitation Bubble

One of the key characteristics of the asymmetric collapse of a cavitation bubble near a rigid boundary is the development of a high speed liquid jet that penetrates the interior of the bubble, impacting on the other side to yield a toroidal bubble. After the formation of the toroidal bubble, a vigorous splash may occur that can lead to pressures on the boundary an order of magnitude greater than the impact pressures associated with the jet. Qualitative agreement with available experimental data is found although, as the bubble approaches minimum volume, shock waves are also observed which further complicate our full understanding of the mechanisms for damage.