Dielectric,thermal, and mechanical properties of CeO2‐filled HDPE composites for microwave substrate applications

Cerium oxide‐filled high density polyethylene (HDPE) composites for microwave substrate applications were prepared by sigma‐blend technique. The HDPE was used as the matrix and the dispersion of CeO₂ in the composite was varied up to 0.5 by volume fraction, and the dielectric properties were studied at 1 MHz and microwave frequencies. The variations of thermal conductivity (k_eff), coefficient of thermal expansion (α_c) and Vicker's microhardness with the volume fraction of the filler were also measured. The relative permittivity (ε_eff) and dielectric loss (tan δ) were found to increase with increase in CeO₂ content. For 0.4 volume fraction loading of the ceramic, the composite had ε_eff = 5.7, tan δ = 0.0068 (at 7 GHz), k_eff = 2.6 W/m °C, α_c = 98.5 ppm/°C, Vicker's microhardness of 18 kg/mm² and tensile strength of 14.6 MPa. Different theoretical approaches have been used to predict the effective permittivity, thermal conductivity, and coefficient of thermal expansion of composite systems and the results were compared with the experimental data. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 998–1008, 2010     

Electrical properties of carbon black‐filled polymer composites

This work deals with the dielectric properties of conductive composite materials, which consist of thermoplastic polypropylene (PP) matrix filled with carbon black (CB). The CB concentration was systematically varied in a wide range. Our main interest is focused on the investigation of electrical conductivity mechanism and related percolation phenomena in these materials. To study the electrical and dielectric properties of composites we used broadband ac dielectric relaxation spectroscopy (DRS) techniques in a wide temperature range. By measurements of complex dielectric permittivity, ϵ*, the dependence of ac conductivity, σ_ac, and dc conductivity, σ_dc, on the frequency, the temperature and the concentration of the conductive filler was investigated. The behavior of this system is described by means of percolation theory. The percolation threshold, P_C, value was calculated to be 6.2 wt.% CB. Both, dielectric constant and dc conductivity follow power‐law behavior, yielding values for the critical exponents, which are in good agreement with the theoretical ones. Indications for tunneling effect in the charge carriers transport through the composites are presented. The temperature dependence of dc conductivity gives evidence for the presence of positive temperature coefficient (PTC) effect.     

Thermomechanical behaviors and dielectric properties of polyaniline‐doped para‐toluene sulfonic acid/epoxy resin composites

Composites based on conductive organic/inorganic fillers dispersed in insulating matrix have been widely investigated because of their widespread applications such as electromagnetic shielding, electrostatic discharge, and sensors. In this context, novel composite materials based on epoxy resin matrix charged with polyaniline (PANI)‐doped para‐toluene sulfonic acid were elaborated. Fourier transform infrared spectroscopy, X‐ray diffraction and scanning electron microscopy were used to check the structure and the morphology of the samples. Viscoelastic behavior and thermal stability of the composites were explored by dynamic mechanical thermal analysis and thermogravimetric analysis. It was shown that the PANI particles exhibited a partial crystalline structure and were homogeneously dispersed in epoxy matrix. Consequently, this structure affected the thermal stability and viscoelastic properties of the composites. Furthermore, the dielectric and electrical properties were investigated up to 1 MHz. Measurements of dielectric properties revealed that with loading fillers in matrix, the dielectric parameters increased to high values at low frequency then decreased at values around 40 and 32 of real and imaginary parts, respectively, at 1 MHz with 15% of PANI content. Copyright © 2011 John Wiley & Sons, Ltd.     

Volume‐exclusion effects in polyethylene blends filled with carbon black,graphite, or carbon fiber

Conductive polymer composites possessing a low percolation‐threshold concentration as a result of double percolation of a conductive filler and its host phase in an immiscible polymer blend afford a desirable alternative to conventional composites. In this work, blends of high‐density polyethylene (HDPE) and ultrahigh molecular weight polyethylene (UHMWPE) were used to produce ternary composites containing either carbon black (CB), graphite (G), or carbon fiber (CF). Blend composition had a synergistic effect on electrical conductivity, with pronounced conductivity maxima observed at about 70–80 wt % UHMWPE in the CB and G composites. A much broader maximum occurred at about 25 wt % UHMWPE in composites prepared with CF. Optical and electron microscopies were used to ascertain the extent to which the polymers, and hence filler particles, are segregated. Differential scanning calorimetry of the composites confirmed that the constituent polymers are indistinguishable in terms of their thermal signatures and virtually unaffected by the presence of any of the fillers examined here. Dynamic mechanical analysis revealed that CF imparts the greatest stiffness and thermal stability to the composites. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1013–1023, 2002     

Electric,dielectric, and dynamic mechanical behavior of carbon black/styrene‐butadiene‐styrene composites

The conductivity of styrene‐butadiene‐styrene block copolymers containing different amounts of extraconductive carbon black (CB) was investigated as a function of the mold temperature. The composites exhibited reduced percolation thresholds (between 1.0 and 2.0 vol % CB). The dynamic mechanical analysis characterization revealed that the glass‐rubber‐transition temperatures of both segments were not affected by the CB addition, although the damping of the polybutadiene phase displayed a progressive drop with an increase in the CB concentration. The normalized curves of tan δ/tan δ_max (where tan δ represents the value of the loss tangent at any measurement temperature and tan δ_max represents the loss tangent peak value at the corresponding temperature T_max) versus T/T_max (where T is the temperature and T_max is the maximum temperature), corresponding to both polystyrene and polybutadiene phases as well as the activation energy related to the glass‐rubber‐transition process, did not present any significant change with the addition of CB. The dielectric analysis revealed the presence of two relaxation peaks in the composite containing 1.5 vol % CB, the magnitude of which was strongly influenced by the frequency, being attributed to interfacial Maxwell‐Wagner‐Sillars relaxations caused by the presence of different interfaces in the composite. The mechanical properties were not affected by the presence of CB at concentrations of up to 2.5 vol %. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2983–2997, 2003     

Preparation and characterization of glass fiber–reinforced polyethylene terephthalate/linear low density polyethylene (GF‐PET/LLDPE) composites

Polyethylene terephthalate (PET) was melt blended with linear low density polyethylene (LLDPE) and subsequently compounded with glass fibers (GF) as reinforcements at percentages ranging from 15 to 45 wt% of LLDPE and 5 to 30 wt% of GF. Thermal, morphological, and mechanical properties of the prepared composites were investigated. It was found that compounding PET/LLDPE blends with GF would be beneficial in producing composites that are thermally stable with good mechanical properties. For example, the impact strength of the composites containing 85/15 wt% (PET/LLDPE) at relatively high loading of GF, ie, from 15 to 30 wt%, was higher than that of the GF‐reinforced neat PET. When increasing the percentage of LLDPE in the composites, the impact strength increased with increasing GF content, and this was also better than that of GF‐reinforced PET whose impact strength drastically decreased upon increasing the GF%. The improvement in mechanical properties of the composite, we suggest, should be correlated with the morphologies of the composites where the visualized interface adhesion tended to be better at higher loadings of both LLDPE and GF.     

Synthesis of multiwalled carbon nanotube/fluorine‐containing poly(p‐phenylene benzoxazole) composites exhibiting greatly enhanced dielectric constants

A series of high‐performance polymer/carbon nanotube (CNT) composites with different nanotube contents have been prepared via condensation of N‐silylated diamino terminated precursor of the polymer with acid chloride‐functionalized CNTs and subsequent thermal cyclodehydration. The composites have been fully characterized by infrared and Raman spectroscopy, electron microscopy, and thermal analysis. Various interesting morphologic features including helical structures have been observed in the composites as a result of covalent attachment of the polymer. The composites exhibit excellent thermal stability and a significant improvement in the dielectric constant and mechanical strength with the inclusion of CNTs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Structure and dielectric properties of a thermoplastic blend containing dispersed metal

In the present work broadband dielectric relaxation spectroscopy measurements were employed to investigate the dielectric properties of polymer composites. A polyethylene/polyoxymethylene (PE/POM) thermoplastic blend was used as a matrix, while the inclusions were iron (Fe) particles. For comparison, the two pure polymers- PE and POM- were used as a matrix, too. In the PE/POM-Fe composites, the polymer matrix is two-phase and the filler particles are localized only in the POM phase, resulting in an ordered distribution of the dispersed filler particles within the blend. In PE-Fe and POM-Fe composites, the filler spatial distribution is random. The behaviour of all the composites studied is described in terms of the percolation theory. The PE/POM-Fe composites, based on the PE/POM blend, demonstrate different electrical behaviour compared to that of POM-Fe and PE-Fe systems. The percolation threshold value of the PE/POM-Fe composites was found much lower than that of the other two systems. The results were related to the microstructure of the composites. A schematic model for the morphology of the composites studied has been proposed. This model explains the peculiar behaviour of the PE/POM-Fe composites by taking into account the ordered distribution of the filler particles in a binary polymer matrix. Optical microscopy photographs confirm this model.     

Rheological properties of UHMWPE/iPP blends

The effects of isotactic polypropylene (PP) on the rheological properties of ultra high molecular weight polyethylene (UHMWPE) have been measured in a broad range of composition (0, 5, 15, 30 wt% PP) at various temperatures (110, 130, and 150°C) and a specific gel concentration of 6 wt%. The result showed that the viscosity of the UHMWPE significantly decreased with the addition and increasing amount of PP. Regardless of temperature, the viscosity function followed the power‐law behavior. Copyright © 2009 John Wiley & Sons, Ltd.     

The direct architecture of carbon fiber‐carbon nanofiber hierarchical reinforcements for superior interfacial properties of CF/epoxy composites

A simple and efficient chemical method was developed to graft directly carbon nanofibers (CNFs) onto carbon fiber (CF) surface to construct a CF‐CNF hierarchical reinforcing structure. The grafted CF reinforcements via covalent ester linkage at low temperature without any usage of dendrimer or catalyst was investigated by FTIR, X‐ray photoelectron spectroscopy, Raman, scanning electron microscopy, atomic force microscopy, dynamic contact angle analysis, and single fiber tensile testing. The results indicated that the CNFs with high density could effectively increase the polarity, wettability, and roughness of the CF surface. Simultaneous enhancements of the interfacial shear strength, flexural strength, and dynamic mechanical properties as well as the tensile strength of CFs were achieved, for an increase of 75.8%, 21.9%, 21.7%, and 0.5%, respectively. We believe the facile and effective method may provide a novel and promising interface design strategy for next‐generation advanced composite structures.     

The acquirement of desirable dielectric properties of carbon nanofiber composites based on the controlled crystallization

This study focused on uncovering the relationship among nanofiller, crystallization behavior, and dielectric property of polymer composites. The effects of carbon nanofibers (CNFs) and heat treatment on the crystalline structures and dielectric properties of the semi‐crystalline polymers were analyzed by using high density polyethylene (HDPE) as a matrix, which is a representative of non‐polar polymer and contains only one crystal structure. The experimental results showed that the degree of crystallinity, size distribution of crystallity, and relative amount of different crystal planes in the HDPE matrix were changing due to the addition of CNFs. With the increase of CNF loading, the dielectric constant, dielectric loss and AC conductivity of the HDPE composites were increased, presenting a typical percolation characteristic, and the dependence of the dielectric constant on frequency became more obvious. All kinds of electronic transmission, polarization effect, and relaxation behaviors in CNF/HDPE composite system were deeply analyzed. After heat treatment, the degree of crystallinity of HDPE composites was decreased with the enhanced cooling rate. For the CNF/HDPE composites with nanofiller content slightly higher than the percolation threshold, the significant increase of the dielectric constant and the dramatical reduction of the dielectric loss over a wide frequency range were realized simultaneously through rapid cooling treatment. The research indicated that a general commercial polymer material with excellent dielectric properties, which exhibited a high dielectric constant and a low dielectric loss, can be obtained by a simple technical approach different from traditional fabrication method of threshold composites.     

Flexural properties of fiber‐reinforced polypropylene composites with and without a transcrystalline layer

The flexural properties of isotactic polypropylene (PP) matrix composites reinforced with 5–30 vol% of unidirectional pitch‐based carbon, polyacrylonitrile (PAN)‐based carbon, e‐glass or aramid fibers were measured using both static and dynamic test methods. Previous research has shown that these pitch‐based carbon and aramid fibers are capable of densely nucleating PP crystals at the fiber surface, leading to the growth of an oriented interphase termed a “transcrystalline layer” (TCL), while the e‐glass and PAN‐based carbon fibers show no nucleating ability. The PP matrices examined included unmodified homopolymers, nucleated homopolymers and PP grafted with maleic anhydride (MA). The composites based on the unmodified PP homopolymers all exhibited poor fiber/matrix adhesion, regardless of fiber type and presence or absence of a TCL. The addition of nucleating agent to the PP matrix had no measurable effect on either the amount of TCL material in pitch‐based carbon‐fiber‐reinforced composites, as measured by wide‐angle X‐ray scattering, WAXS, or the static flexural properties of the composites reinforced with either type of carbon fiber. However, MA grafting reduced the transcrystalline fraction of the matrix in pitch‐based carbon‐fiber‐reinforced composites; at the highest level of MA grafting, the TCL was completely suppressed. In addition, high levels of MA grafting improved the transverse flexural modulus of the composites containing both types of carbon fibers, and reduced the extent of fiber pull‐out, indicating an improvement in fiber/matrix adhesion. Copyright © 1999 John Wiley & Sons, Ltd.     

Date palm fibre filled recycled ternary polymer blend composites with enhanced flame retardancy

Flammability of recycled polypropylene (PP)/low density polyethylene (LDPE)/high density polyethylene (HDPE) ternary blends containing date palm fibres is investigated in this study. Melt blending is used for the composite preparation and the palm fibres induce good mechanical strength to the blend composites. The effect of flame retardant magnesium hydroxide, is studied through the limiting oxygen index analysis and cone calorimeter studies. Morphology of the palm fibres in presence of fire retardant reveals interesting facts of base hydrolysis. Since the polymers used are recycled ones and the fibres are obtained from the date palm leaves, the whole composite manufactured stands as low cost, less energy consuming and environmental friendly. Though the flame retardant reduced the mechanical properties, the palm fibres strengthened the whole composite thus helping to achieve the flame retardancy and mechanical properties simultaneously. Flame retardancy is correlated with the thermal degradation and thermal conductivity of the blend fibre composites as well.     

The interlaminar shear strength and tribological properties of PA 6 composites filled with graphene oxide‐treated carbon fiber

The objective of this work is to improve the interlaminar shear strength and tribological properties of the PA 6 composites by graphene oxide‐treated carbon fiber (CF) and ultraviolet irradiation of PA 6. The morphologies of untreated and treated CFs were characterized by X‐ray photoelectron spectroscopy. Surface analysis showed that after treatment, the surface of CFs chemisorbed oxygen‐containing groups; active carbon atom, the surface roughness, and wetting ability were increased. The results show that the treated CF composites can possess excellent interfacial properties and tribological properties accordingly after treatment. Copyright © 2017 John Wiley & Sons, Ltd.     

The flexural and tribological properties of UHMWPE composite filled with plasma surface‐treated wood fibers

In this paper, the wear performance of an ultra‐high molecular weight polyethylene composites filled with wood fiber were studied using a pin‐on‐disc method. The effects of surface treatment of wood fiber and sliding load and on the friction and wear of the wood fiber/UHMWPE composite are reported. The test results showed that the sliding load is an important controlling factor; its effect is diminished when the wood fiber is modified.     

Improved mechanical properties of epoxy composites reinforced with surface‐treated UHMWPE fibers

The surface treatment of ultra‐high molecular weight polyethylene fiber using potassium permanganate and the mechanical properties of its epoxy composites were studied. After treatment, many changes were happened in the fiber surface: more O‐containing groups (―OH, ―C═O, and ―C―O groups), drastically decreased contact angles with water and ethylene glycol, slightly increased melting point and crystallinity, and formed cracks. Different contents (0.1–0.5 wt%) ultra‐high molecular weight polyethylene fibers/epoxy composites were prepared. The results indicated that the surface treatment decreased the tensile strength of epoxy composites, but increased the bending strength. When the fiber content was 0.3 wt%, the above properties reached the maximum. At the same fiber content, the interlaminar shear strength of the composites was increased by 26.6% up to the as‐received fiber composites. Dynamic mechanical analysis of the composites suggested the storage modulus and tanδ were decreased due to the surface treatment. Fractured surface analysis confirmed that the potassium permanganate treatment was effective in improving the interface interaction.     

Improved interfacial properties of carbon fiber/UHMWPE composites through surface coating on carbon fiber surface

Carbon fibers were coated in an attempt to improve the interfacial properties between carbon fibers and ultra‐high molecular weight polyethylene resin matrix. Atomic force microscopy, scanning electron microscopy, and X‐ray photoelectron spectroscopy were performed to characterize the changes of carbon fiber surface. Atomic force microscopy results show that the coating of carbon fiber significantly increased the carbon fiber surface roughness. X‐ray photoelectron spectroscopy indicates that silicon containing functional groups obviously increased after modification. Interlaminar shear strength was used to characterize the interfacial properties of the composites.     

The investigation of the friction and wear properties of surface‐treated carbon fiber/SiO2 reinforced PMMA composites

The mechanical properties of SiO₂ filler particles on carbon fibers have been under discussion for several decades; the diverse models, and the properties of the components relevant to retention, are critically reviewed in the first part of this study. In addition, to gain an insight into some possible combined effect of the carbon fiber/poly(methyl methacrylate) (CF/PMMA), interfacial adhesion strength and the tensile properties and dielectric strength of the hybrid composites were studied. Simple modified rules of mixtures are used to estimate the fiber efficiency factors for the strength and modulus of the hybrid composites. Except, with the increasing fraction of CFs in PMMA, the weld line area's elongation percent is decreased. Whereas for case of SiO₂, the 10 wt% is the threshold for micro injection molded weld line tensile strength and dielectric strength turning from decrease trend to increase. Same as CF, elongation of micro weld line samples is in general lower than neat PMMA as well, due to the addition of SiO₂ particles.     

Influence of talc with different particle sizes in melt‐mixed LLDPE/MWCNT composites

Linear low‐density polyethylene (LLDPE) was melt‐mixed with multiwalled carbon nanotubes (MWCNTs) and varying amounts of three different kinds of talc (phyllo silicate), each with a different particle size distribution, to examine the effect of these filler combinations with regards to the electrical percolation behavior. The state of the filler dispersion was assessed using transmission light microscopy and electron microscopy. The use of talc as a second filler during the melt mixing of LLDPE/MWCNT composites resulted in an improvement in the dispersion of the MWCNTs and a decrease of the electrical percolation threshold. Talc with lower particle sizes showed a more pronounced effect than talc with larger particle sizes. However, the improvement in dispersion was not reflected in the mechanical properties. Modulus and stress values increase with both, MWCNT and talc addition, but not in a synergistic manner. The crystallization behavior of the composites was studied by differential scanning calorimetry to determine its potential influence on the electrical percolation threshold. It was found that the crystallinity of the matrix increased slightly with the addition of talc but no further increments were observed with the incorporation of the MWCNTs. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1680–1691     

Preparation and properties of hollow silica tubes/bismaleimide/diallylbisphenol A composites with improved toughness,dielectric properties,and flame retardancy

New high performance insulating composites based on hollow silica tubes (mHST) and bismaleimide/diallylbisphenol A (BDM/DBA) resin, which exhibit improved toughness, dielectric properties, and flame retardancy, were successfully developed. The effect of the amount of mHST on the properties of composites was systematically studied. Results show that the impact strength of the composite with 0.5 wt% mHST is about 2.2 times that of BDM/DBA resin. In addition, compared with BDM/DBA resin, the composites show lower and stable dielectric constant, better frequency stability of dielectric loss, significantly improved flame retardancy, and similarly outstanding thermal resistance. The reasons behind these attractive integrated properties are discussed from the view of structure–property relationship. Copyright © 2011 John Wiley & Sons, Ltd.