Polymer–filler interactions in sol–gel derived polymer/silica hybrid nanocomposites

The effect of polymer–filler interaction on solvent swelling and dynamic mechanical properties of the sol–gel derived acrylic rubber (ACM)/silica, epoxidized natural rubber (ENR)/silica, and poly (vinyl alcohol) (PVA)/silica hybrid nanocomposites has been described for the first time. Tetraethoxysilane (TEOS) at three different concentrations (10, 30, and 50 wt %) was used as the precursor for in situ silica generation. Equilibrium swelling of the hybrid nanocomposites in respective solvents at ambient condition showed highest volume fraction of the polymer in the swollen gel in PVA/silica system and least in ACM/silica, with ENR/silica recording an intermediate value. The Kraus constant (C) also followed a similar trend. In dynamic mechanical analysis, the storage modulus dropped at higher strain (>1%), which indicated disengagement of polymer segments from the filler surfaces. This drop was maximum in ACM/silica, intermediate in ENR/silica, and minimum in PVA/silica, both at 50 and 70 °C. The drop in modulus with theoretical volume fraction of silica (ϕ) was interpreted with the help of a Power law model ΔE′ = a₁ϕ, where a₁ was a constant and b₁ was primarily a filler attachment parameter. Strain dependence of loss modulus was observed in ACM/silica hybrid nanocomposites, while ENR/silica and PVA/silica nanocomposites showed almost strain‐independent behavior. The storage modulus showed sharp increase with increasing frequency in ACM/silica system, while that was lower in both ENR/silica (at higher frequency) and PVA/silica systems (in the entire frequency spectrum). The increase in modulus with ϕ also followed similar model ΔE′ = a₂ϕ proposed in the strain sweep mode. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2399–2412, 2005     

Unusual inorganic phase formation in ultraviolet‐curable organic–inorganic hybrid films

Inorganic–organic hybrid materials were prepared with a cycloaliphatic epoxide adduct of linseed oil with tetraethylorthosilicate (TEOS) oligomers via a cationic UV‐curing process. The TEOS oligomers were prepared in the presence of water and ethanol with hydrochloric acid as a catalyst. The TEOS oligomers were characterized with ¹H and ²⁹Si NMR and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. Hybrid films were cured, and the dynamic mechanical and thermal properties of the hybrid films were evaluated as a function of the TEOS oligomer content. The morphology of the hybrid films was examined with atomic force microscopy, transmission electron microscopy, and small‐angle light scattering. The microscopy and dynamic mechanical data indicated that the hybrid films were heterogeneous materials with various inorganic particle sizes dispersed within the organic matrix. In addition, ²⁹Si solid‐state NMR spectroscopy was used to investigate the coupling between the silicate region and organic regions. A schematic model is proposed to address structural features of hybrid materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1607–1623, 2005     

Acrylic polymer/silica organic–inorganic hybrid emulsions for coating materials: Role of the silane coupling agent

Acrylic polymer/silica organic–inorganic hybrid emulsions were synthesized by a simple method, that is, a conventional emulsion polymerization and subsequent sol–gel process, to provide water‐based coating materials. The acrylic polymer emulsions contained a silane coupling agent monomer, such as methacryloxypropyltriethoxysilane, to form highly solvent‐resistant hybrid films. On the other hand, the hybrid films from the surface‐modified polymer emulsions, in which the silane coupling agent was located only on the surface of the polymer particles and the particle core was not crosslinked, did not exhibit high solvent resistance. A honeycomblike array structure, which was derived from the polymer particles (diameter ≈ 50 nm) and the silica domain, on the hybrid film surfaces was observed by atomic force microscopy. The crosslinked core part and silane coupling agent containing the shell part of the polymer particles played important roles in attaining high solvent resistance. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4736–4742, 2006     

Solid‐state lasers based on inorganic–organic hybrid materials obtained by combined sol–gel polymer technology

Sol–gel glass matrices in which organic laser dyes are embedded can be used as the gain medium in solid‐state, continuously tunable lasers. Such lasers are very simple to construct, and potentially very compact and efficient. Unlike the commonly used liquid dye laser systems, solid‐state dye lasers can be made mechanically robust and portable. In this article, the development of sol–gel/dye lasers, including the sol–gel technology, dye properties, and laser operation, is reviewed. In addition, new solid‐state hosts (such as polyurethane/silica ORMOSILs), additional organic dyes (cyanines), and new studies on the stability of the dyes are presented. Copyright © 2004 John Wiley & Sons, Ltd.     

A facile synthesis of highly water-soluble, core–shell organo-silica nanoparticles with controllable size via sol–gel process

A series of highly water-soluble organo-silica nanoparticles, ranging from 2 to 10 nm in diameter, were synthesized by the cohydrolysis and copolycondensation reactions. ω-methoxy(polyethyleneoxy)propyltrimethoxysilane (PEG6-9) and hydroxymethyltriethoxysilane (HMTEOS) mixtures were catalyzed by sodium hydroxide in the presence of surfactant benzethonium chloride (BTC) with various ratios of PEG6-9/HMTEOS at room temperature. The synthesized organo-silica nanoparticles possess a core–shell structure with a core of organo-silica resulting from HMTEOS and a monolayer shell of PEG6-9. The chemo-physical characteristics of the particles were studied by gel permeation chromatography (GPC), Fourier transform infrared (FTIR) spectroscopy, ²⁹Si nuclear magnetic resonance (NMR), dynamic light scattering (DLS), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). The molecular weight and particle size of the particles increased with increasing HMTEOS molar ratios. The richest HMTEOS composition for the water-soluble particles was found to be HMTEOS:PEG6-9 = 80:20, where the particles had a 6 nm diameter core and a 0.8 nm thick shell. We propose that these water-soluble organo-silica nanoparticles will be suitable for biomedical applications.     

Surlyn®/titanate hybrid materials via polymer in situ sol–gel chemistry

Acid form Surlyn®/titanate hybrid materials were achieved by polymer in situ sol–gel reactions for a titanium alkoxide monomer. Atomic force microscopic images revealed arrays of titania nanoparticles having diameters of 10–30 nm. Fourier transform infrared spectra verified the presence of an internally polymerized titanate phase although unhydrolyzed TiOR groups were present. Carboxylic acid dimerization was complete at room temperature, but carboxylate anions appeared at higher titanate levels. The methylene rocking doublet persisted upon incorporation of the inorganic component, which supported the idea of largely undisrupted crystallinity. Thermogravimetric analysis showed that the degradation onset temperature of each hybrid is largely unaffected by the presence of the inorganic filler, which is consistent with the concept of an isolated titanate phase. The first‐scan differential scanning calorimetric thermogram for unfilled Surlyn® revealed the usual twin‐melting endotherms. In contrast, the primary, high‐temperature melting endotherm was seen on the first scan for the Surlyn®/titanate hybrids, but the lower temperature endotherm was either not present or weak. Primary melting persisted after several cycles of heating above the melting temperature followed by cooling, demonstrating that primary crystallinity persisted despite titanate phase incorporation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 11–22, 2003     

Preparation and properties of silylated PTFE/SiO2 organic–inorganic hybrids via sol–gel process

A study on poly(tetrafluoroethylene) (PTFE) reinforced with tetraethoxysilanes (TEOS) derived SiO₂ is described. It included the manufacturing process of SiO₂‐reinforced PTFE and the effects of silylation agent on the properties of the hybrid material, such as porosity, hydrophobic, thermal resistance, dielectric and mechanical properties, and microstructure. PTFE/SiO₂ hybrids of 50 wt % SiO₂ loading were prepared via a sol–gel process and were shaped by a two‐roll milling machine. Trimethylchlorosilane and hexamethydisilazane were used as the silylation agents. Our results showed that the water absorption and dielectric loss of PTFE/SiO₂ hybrid had significantly improved with silylation agent. The silylation process replaced Si? OH with Si? CH₃ on the surface of the TEOS‐derived silica colloidal particle. The existence of trimethylsilyl [? Si(CH₃)₃] on the surface of the modified PTFE/SiO₂ hybrid was confirmed via infrared and solid‐state ²⁹Si magic‐angle spinning nuclear magnetic resonance spectra. Nitrogen‐sorption techniques were used to characterize the modified and unmodified PTFE/SiO₂ hybrids. The microstructure of SiO₂ in the matrix was also evaluated with scanning electron microscopy and transmission electron microscopy. Our results showed that the silylated sol–gel‐derived PTFE/SiO₂ hybrids had exhibited high porosity (53.7%) with nanosize pores (10–40 nm) and nanosize colloidal particles (20–50 nm). This manifests itself as have the ultralow dielectric properties (D_k = 1.9 and D_f = 0.0021), low coefficient of thermal expansion (66.5 ppm/°C), high tensile modulus (141 MPa), excellent thermal resistance (T_d = 612 °C), and an increased hydrophobia (θ = 114°); moreover, the hydrophobic property of the PTFE/SiO₂ hybrid was thermally stable up to 400 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1789–1807, 2004     

Synthesis and optical properties of organic–inorganic hybrid semi‐interpenetrating polymer network gels containing polyfluorenes

Organic–inorganic hybrid semi‐interpenetrating polymer network (semi‐IPN) gels containing polyfluorenes (PFs) are synthesized by hydrosilylation reaction of joint and rod molecules in toluene, where PFs are poly(9,9‐dihexylfluorene‐2,7‐diyl) (PF6) or, poly(9,9‐dioctylfluorene‐2,7‐diyl) (PF8), joint molecules are 1,3,5,7‐tetramethylcyclotetrasiloxane (TMCTS), or 1,3,5,7,9,11,13,15‐octakis(dimethylsilyloxy)pentacyclo‐[9,5,1,1,1,1]octasilsesquioxane (POSS), and rod molecules are 1,5‐hexadiene (HD) or 1,9‐decadiene (DD). The semi‐IPN gels containing low molecular weight PF6 show higher photoluminescence efficiency (?_g) than the toluene solution of PF6L (?_s). The semi‐IPN gels composed of long rod molecule of DD and cubic joint molecule of POSS show the most effective increase in the emission intensity. The emission intensity of PF6L increases as formation of the network in the POSS‐DD semi‐IPN gel. The POSS‐DD semi‐IPN gels containing high molecular weight PF6 and PF8 also show the increase of emission intensity than those of the toluene solutions. The semi‐IPN synthesized in cyclohexane show syneresis and phase separation between network structure and PF chains. The semi‐IPN gels containing PF8 show emission peaks at 450 and 470 nm derived from β‐sheet structure of PF8. A systematic study clears correlation between emission property and network structure and/or composition of semi‐IPN gels. The semi‐IPN gels provide emissive self‐standing soft materials with high efficiency and in a narrow wavelength range emission. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 973–984     

Combination of radical and cationic photoprocesses for the single‐step synthesis of organic‐inorganic hybrid films

Nanocomposite materials prepared from radically photocurable hybrid sol–gel precursors have been widely developed within the last decade, especially to devise novel optical devices and coatings. For their synthesis, a preferential route has involved in the successive sol–gel process of acrylate trialkoxysilane precursors followed by radical photopolymerization. In contrast, this work presents an original one‐step synthesis based on the association of two different photoinitiators (PIs) in the same formulation: the photolysis of a hydroxyphenylketone (radical PI) affords polyacrylate chains while that of a diaryl iodonium salt (cationic PI) generates powerful superacids catalyzing the sol–gel reactions of the alkoxy functions. The behavior of methacrylate and acrylate trimethoxysilane precursors was compared to highlight the effect of the organic moiety functionality on the reaction kinetics (Fourier transform infrared spectroscopy) and the film microstructure (¹³C and ²⁹Si solid‐state nuclear magnetic resonance). Interestingly, evidence of local organization in these hybrid films was also given by X‐ray analysis. In a last part, their thermomechanical properties were discussed thoroughly using a range of techniques: DSC, scratch‐resistance test, nanoindentation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4150–4158, 2010     

Ionic transport phenomenon across sol–gel derived organic–inorganic composite mono-valent cation selective membranes

Organic–inorganic composite mono-valent cation selective membranes (MCSMs) were prepared by sol–gel under acidic conditions, in which sulfonic acid groups were introduced at the inorganic segment. Studies on physicochemical and electrochemical properties revealed their excellent mechanical, thermal, and oxidative stabilities, high conductivity, ion-exchange capacity, permselectivity for mono-valent cations, ionic diffusion and water transport number. These properties suggested the suitability of MCSMs, especially Si-65%, for electro-separation of Na⁺ from Ca²⁺, Mg²⁺, and Fe³⁺. The effect of electrolyte solution on the characteristics of the current–voltage (i–v) curve in MCSM was studied based on the concentration polarization. Electro-transport of different ions in terms of plateau length and concentration profiles for different ions in the solution phase, diffusion boundary layer and membrane phase were presented. Information obtained from i–v curve analysis were validated by electrodialysis (ED) experiments for individual or mixed electrolyte solutions. Electro-transport efficiency and separation factor of different ions for MCSM and Nafion117 (N117) membranes were compared, which suggested suitability of MCSMs for separating cations.     

Healable dual organic–inorganic crosslinked sol–gel based polymers: Crosslinking density and tetrasulfide content effect

In this article, the first generation of healable sol–gel based polymers is reported. A dual organic–inorganic crosslinked network is developed containing non‐reversible crosslinks and reversible (tetrasulfide) groups. The designed polymer architecture allows thermally induced mesoscale flow leading to damage closure followed by interfacial strength restoration due to reformation of the reversible groups. While the reversible bonds are responsible for the flow and the interface restoration, the irreversible crosslinks control the required mechanical integrity during the healing process. The temperature dependent gap closure kinetics is strongly affected by the crosslinking density and tetrasulfide content. Raman spectroscopy is used to explain the gap closure kinetics in air and dry nitrogen. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1953–1961     

Tryptophan photooxidation promoted by new hybrid materials prepared by condensation of naphthalene imides with silicate by the sol–gel process

Three novel hybrid organic/inorganic materials were synthesized from 4-substituted (NO₂, Br, H) 1,8-naphthalene imide-N-propyltriethoxysilane by the sol–gel process. These materials were obtained as a xerogel and partially characterized. The ability to photosensitize the oxidation and degradation of tryptophan indole ring by these materials was studied through photophysical and photochemical techniques. Although the derivatives containing Br and NO₂ as substituent do not cause efficient tryptophan photodamage, the hybrid material obtained from 1,8-naphthalic anhydride is very efficient to promote tryptophan photooxidation. By using laser flash photolysis it was possible to verify the presence of naphthalene imide transient radical species. The presence of oxygen causes an increase of the yield of radical formation. These results suggest that the mechanism of photodegradation of tryptophan occurs by type I, i.e. the transient radical (TrpH⁺) formed by the direct reaction of the triplet state of the naphthalene imide moiety with tryptophan. Thus a inorganic–organic hybrid material that can be used to promote the oxidation of biomolecules was obtained.     

Synthesis of organic‐inorganic hybrid gels by means of thiol‐ene and azide‐alkene reactions

Organic–inorganic hybrid gels have been synthesized from a multi‐vinyl functional cyclic siloxane, 1,3,5,7‐tetravinyltetramethylcyclotetrasiloxane (TVMCTS), or a cubic silsesquioxane, octavinyloctasilasesquioxane (PVOSS), and α,ω‐dithiol compounds, 1,6‐hexanedithiol (HDT), 1,10‐decanedithiol (DDT), using thiol‐ene reaction in toluene. The network structure of the resulting gels, mesh size and mesh size distribution, was quantitatively characterized by means of a scanning microscopic light scattering (SMILS). The gels obtained from TVMCTS‐HDT formed homogeneous network structure with 1.5–1.6 nm mesh. Relaxation peaks derived from large clusters and/or micro gels were detected in the SMILS analysis of the TVMCTS‐DDT, PVOSS‐HDT, and PVOSS‐DDT gels besides those from the small meshes. The organic–inorganic hybrid gels were also synthesized from TVMCTS, PVOSS with α,ω‐diazide compounds, 1,6‐hexanediazide (HDA), 1,10‐decanediazide (DDA), using azide‐alkene reaction in toluene. All the gels obtained with the azide‐alkene reaction formed the homogeneous network structure. Enthalpy relaxation at the glass transition of the dried samples was detected by differential scanning calorimetry to study the network uniformity of the original gels. The gels synthesized by the azide‐alkene reaction showed larger enthalpy than the gels synthesized by the thiol‐ene reaction, indicating homogeneous network structure in the former gels. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2229–2238     

An organic–inorganic hybrid compound containing imidazolium cations and a one‐dimensional lithium hexacyanidocobaltate‐based anionic framework

An organic–inorganic hybrid compound, catena‐poly[bis(3H‐imidazol‐1‐ium) [[tetracyanido‐κ⁴C‐cobalt(III)]‐μ‐cyanido‐κ²C:N‐[diaqualithium(I)]‐μ‐cyanido‐κ²N:C]], {(C₃H₅N₂)₂[CoLi(CN)₆(H₂O)₂]}_n, was synthesized by the reaction of Li₃[Co(CN)₆] with imidazolium chloride in aqueous solution. The compound crystallizes in the monoclinic space group C2/c (data collected at 273 K). In the crystal structure, neighbouring [Co(CN)₆]³⁻ anionic units are linked by Li⁺ cations through the cyanide groups in a trans mode, forming a one‐dimensional zigzag chain structure extending along the c axis. A three‐dimensional supramolecular network is formed through hydrogen‐bonding interactions and is further stabilized by weak CN...π interactions between the cyanide groups and the imidazolium cations.     

Acrylic polymer/silica hybrids prepared by emulsifier‐free emulsion polymerization and the sol–gel process

Acrylic polymer/silica hybrids were prepared by emulsifier‐free emulsion polymerization and the sol–gel process. Acrylic polymer emulsions containing triethoxysilyl groups were synthesized by emulsifier‐free batch emulsion polymerization. The acrylic polymer/silica hybrid films prepared from the acrylic polymer emulsions and tetraethoxysilane (TEOS) were transparent and solvent‐resistant. Atomic force microscopy studies of the hybrid film surface suggested that the hybrid films did not contain large (e.g., micrometer‐size) silica particles, which could be formed because of the organic–inorganic phase separation. The Si? O? Si bond formed by the cocondensation of TEOS and the triethoxysilyl groups on the acrylic polymer increased the miscibility between the acrylic polymer component and the silica component in the hybrid films, in which the nanometer‐size silica domains (particles) were dispersed homogeneously in the acrylic polymer component. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 273–280, 2006     

Flame‐retardant epoxy resins: An approach from organic–inorganic hybrid nanocomposites

Phosphorus‐containing epoxy‐based epoxy–silica hybrid materials with a nanostructure were obtained from bis(3‐glycidyloxy)phenylphosphine oxide, diaminodiphenylmethane, and tetraethoxysilane in the presence of the catalyst p‐toluenesulfonic acid via an in situ sol–gel process. The silica formed on a nanometer scale in the epoxy resin was characterized with Fourier transform infrared, NMR, and scanning electron microscopy. The glass‐transition temperatures of the hybrid epoxy resins increased with the silica content. The nanometer‐scale silica showed an enhancement effect of improving the flame‐retardant properties of the epoxy resins. The phosphorus–silica synergistic effect on the limited oxygen index (LOI) enhancement was also observed with a high LOI value of 44.5. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 986–996, 2001     

Liquid‐crystalline organic–inorganic hybrid polymers with functionalized silsesquioxanes

Liquid‐crystalline (LC) hybrid polymers with functionalized silsesquioxanes with various proportions of LC monomer were synthesized by the reaction of polyhedral oligomeric silsesquioxane (POSS) macromonomer with methacrylate monomer having an LC moiety under common free‐radical conditions. The obtained LC hybrid polymers were soluble in common solvents such as tetrahydrofuran, toluene, and chloroform, and their structures were characterized with Fourier transform infrared, ¹H NMR, and ²⁹Si NMR. The thermal stability of the hybrid polymers was increased with an increasing ratio of POSS moieties as the inorganic part. Because of the steric hindrance caused by the bulkiness of the POSS macromonomer, the number‐average molecular weight of the hybrid polymers gradually decreased as the molar percentage of POSS in the feed increased. Their liquid crystallinities were very dependent on the POSS segments of the hybrid polymers behaving as hard, compact components. The hybrid polymer with 90 mol % LC moiety (Cube‐LC90) showed liquid crystallinity, larger glass‐transition temperatures, and better stability with respect to the LC homopolymer. The results of differential scanning calorimetry and optical polarizing microscopy showed that Cube‐LC90 had a smectic‐mesophase‐like fine‐grained texture. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4035–4043, 2001     

Nanostructured organic–inorganic hybrid films prepared by the sol–gel method from self‐assemblies of PS‐b‐paptes‐b‐PS triblock copolymers

ABA‐based triblock copolymers of styrene as block ends and gelable 3‐acryloxypropyltriethoxysilane (APTES) as the middle block were successfully prepared through nitroxide‐mediated polymerization (NMP). The copolymers were bulk self‐assembled into films and the degree of phase separation between the two blocks was evaluated by differential scanning calorimetry (DSC). Their morphology was examined through small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM), whereas the mechanical properties of the corresponding cross‐linked self‐assembled nanostructures were characterized by dynamic mechanical analysis (DMA). Acidic treatment of the triblock copolymers favored the hydrolysis and condensation reactions of the APTES‐rich nanophase, and induced a mechanical reinforcement evidenced by the increase of storage modulus values and the shift of the glass transition temperature to higher temperatures due to confinement effects. In addition, the lamellar structure of the hybrid films was retained after the removal of the organic part by calcination. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Organic–inorganic hybrid membranes prepared from the sol–gel process of poly(butyleneadipate‐co‐terephthalate) and TiO2

Organic–inorganic hybrids based on poly(butyleneadipate‐co‐terephthalate)/titanium dioxide (PBAT/TiO₂) hybrid membranes were prepared via a sol–gel process. The PBAT/TiO₂ hybrid membranes were prepared for various PBAT/TiO₂ ratios. The resulting hybrids were characterized with a morphological structure, hydrophilicity, biodegradability, and thermal properties. The results showed that macrovoids underwent a transition into a sponge‐like membrane structure with the addition of TiO₂. After sol–gel transition, a strong interaction between the inorganic network and polymeric chains led to an increase in glass transition temperature (T_g), thermal degrading temperature, and hydrophilicity, and hence a higher biodegradability. According to X‐ray diffraction measurements of the crystal structure of the hybrid, the presence of TiO₂ did not change the crystal structure of PBAT. TiO₂ networks are uniformly dispersed into the PBAT matrix and no aggregation of TiO₂ networks in the hybrid membranes was observed through the small angle X‐ray scattering measurements. Thus, the sol–gel process of PBAT and TiO₂ can be used to prepare a hybrid with higher application temperature and faster biodegradation rate. Copyright © 2008 John Wiley & Sons, Ltd.     

Nafion®/(organically modified silicate) nanocomposites via polymer in situ sol–gel reactions: Mechanical tensile properties

A series of Nafion®/[organically modified silicate (ORMOSIL)] hybrid materials have been created by in situ sol–gel copolymerizations of tetraethylorthosilicate and semiorganic silicon alkoxide monomers. The trends in the mechanical tensile properties of these hybrid materials were largely rationalized in terms of the entrapment of the long sulfonic acid side chains in silicate or ORMOSIL structures. There is a significant increase in the mechanical strength relative to that of unfilled Nafion®, except in one case. Young's modulus is enhanced relative to that of unfilled acid form Nafion® in a number of cases, although the degree of ductility is reduced relative to that of unfilled Nafion®. The filler fractions are beneath a critical value that would reflect percolation of a glassy, direct load‐bearing silicate phase. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2237–2247, 2002