Synthesis and characterization of an adipic acid–derived epoxy resin

Adipic acid, a highly abundant chemical that can be produced from biomass, was used to prepare an aromatic‐free epoxy resin. Synthesis of the diglycidyl adipate was performed by a one‐step process using epichlorohydrin and by a two‐step process comprising allylation and epoxidation. The viscosity of diglycidyl adipate is 25 mPa·s, which is 99% lower than the diglycidyl ether of bisphenol A (DGEBA). The storage modulus at 25 °C for cured diglycidyl adipate and DGEBA is 2000 and 3200 MPa, respectively. The alpha transition temperature through peak of the loss modulus and the peak of tan(δ), are 77 °C and 90 °C, respectively. Low‐viscosity epoxy applications are discussed herein. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2625–2631     

Amine‐cured epoxy/clay nanocomposites. II. The effect of the nanoclay aspect ratio

The thermophysical and mechanical properties of a nanocomposite material composed of amine‐cured diglycidyl ether of bisphenol A (DGEBA) reinforced with organomontmorillonite clay are reported. The storage modulus at 100 °C, which was above the glass‐transition temperature (T_g), increased approximately 350% with the addition of 10 wt % (6.0 vol %) of clay. Below the T_g, the storage modulus at 30 °C increased 50% relative to the value of unfilled epoxy. It was determined that the T_g linearly increased as a function of clay volume percent. The tensile modulus of epoxy at room temperature increased approximately 50% with the addition of 10 wt % of clay. The reinforcing effect of the organoclay nanoplatelets is discussed with respect to the Tandon–Weng and Halpin–Tsai models. A pseudoinclusion model is proposed to describe the behavior of randomly oriented, uniformly dispersed platelets in nanocomposite materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4391–4400, 2004     

Synthesis and characterization of P/Si flame retardant and its application in epoxy systems

In this report, a novel phosphorus/silicon‐containing reactive flame retardant, hexa(3‐triglycidyloxysilylpropyl)triphosphazene (HGPP), was synthesized and characterized by Fourier transform infrared spectrometry and nuclear magnetic resonance spectra (¹H, ³¹P, and ²⁹Si), respectively. To prepare cured epoxy, HGPP had been co‐cured with diglycidyl ether of bisphenol‐A (DGEBA) via 4,4‐diaminodiphenylsulfone as a curing agent. The mechanical, thermal, and flame retardant properties of the cured epoxy were evaluated by dynamic mechanical analysis, thermogravimetric analysis, and limiting oxygen index (LOI). According to these results, it could be found that incorporation of HGPP in the cured epoxy system showed good thermal stability, high LOI values, and high char yield at high temperature. As moderate loading of HGPP in the epoxy system, its storage modulus and glass transition temperature were higher than those of neat DGEBA. Copyright © 2011 John Wiley & Sons, Ltd.     

Reaction epoxy-amine: Suivi du mecanisme reactionnel et de la cinetique par RMN 13C, 15N et HPLC

The curing reaction of diglycidyl ether of bisphenol A (DGEBA) with metaphenylene diamine (mPDA) was investigated with high performance liquid chromatography (HPLC) and Fourier transform nuclear magnetic resonance spectroscopy (FT NMR ¹³C and ¹⁵N). With the results obtained from a series of models a mechanism was proposed and the cure kinetics were obtained at 100°C. The major conclusion is that the cure proceeded mainly by chain extension, whereas crosslinking occurred in the reaction of hydroxyl groups with epoxides and resulted in the formation of ether linkages.     

Investigating properties of poly (ether‐amide)/MWCNT nanocomposite films containing 2,7‐bis(4‐aminophenoxy)naphthalene and isophthalic segments

Three nanocomposite films based on aramid (poly (ether‐amide), PEA) and multiwall carbon nanotubes (MWCNT) were prepared via solution casting method using 2,7‐bis(4‐aminophenoxy)naphthalene (4) and isophthalic acid (5) containing various amounts of MWCNT (2, 3, 5 wt.%). To comprehensively analyze the properties of the cast films as well as the monomers, different techniques were employed, namely FT‐IR, ¹H NMR, X‐ray diffraction, and field emission scanning electron microscopy. Also, thermal and tensile properties of PEA (6) and nanocomposite films were investigated using thermogravimetric analysis and mechanical analysis, respectively. The morphology, thermal, and mechanical properties of nanocomposite films approved that MWCNT had well dispersion in the PEA matrix and showed a synergistic effect on improving all of the investigated properties. Based on the thermogravimetric analysis results, employing MWCNT caused to increase in the char yields from 61 (in the neat PEA) to 66 (in the PEA /MWCNT nanocomposite 5 wt.%) under the nitrogen atmosphere. In comparison to the pristine PEA (426°C), the temperature at 10 losses mass % (T₁₀) was increased from 530°C to 576°C, with 2 to 5 wt.% of MWCNT. Mechanical analysis revealed that the tensile strength and initial modulus were improved by incorporating MWCNT into PEA (81.70–93.40 MPa and 2.10–2.22 GPa, respectively). Electrical conductivity of the PEA/MWCNT nanocomposites was displayed maximum value in the 5 wt.%, showing satisfactory value in many application areas. The X‐ray diffraction technique was employed to study the crystalline structure of the prepared nanocomposite films as well as PEA. In addition, the electrochemical impedance spectroscopy study demonstrated that the prepared nanocomposites had significant impedance improvement in the presence of MWCNTs.     

Morphology,toughness mechanism,and thermal properties of hyperbranched epoxy modified diglycidyl ether of bisphenol A (DGEBA) interpenetrating polymer networks

New hyperbranched poly(trimellitic anhydride‐triethylene glycol) ester epoxy (HTTE) is synthesized and used to toughen diglycidyl ether of bisphenol A (DGEBA) 4,4′‐diaminodiphenylmethane (DDM) resin system. The effects of content and generation number of HTTE on the performance of the cured systems are studied in detail. The impact strength is improved 2–7 times for HTTE/DGEBA blends compared with that of the unmodified system. Scanning electron microscopy (SEM) of fracture surface shows cavitations at center and fibrous yielding phenomenon at edge which indicated that the particle cavitations, shear yield deformation, and in situ toughness mechanism are the main toughening mechanisms. The dynamic mechanical thermal analyzer (DMA) analyses suggest that phase separation occurred as interpenetrating polymer networks (IPNs) for the HTTE/DGEBA amine systems. The IPN maintains transparency and shows higher modulus than the neat epoxy. The glass transition temperature (T_g) decreases to some extent compared with the neat epoxy. The T_g increases with increase in the generation number from first to third of HTTE and the concentrations of hard segment. The HTTE leads to a small decrease in thermal stability with the increasing content from TGA analysis. The thermal stability increases with increase in the generation number from first to third. Moreover, HTTE promotes char formation in the HTTE/DGEBA blends. The increase in thermal properties from first to third generation number is attributed to the increase in the molar mass and intramolecular hydrogen bridges, the increasing interaction of the HTTE/DGEBA IPNs, and the increasing crosslinking density due to the availability of a greater number of end hydroxyl and end epoxide functions. Copyright © 2008 John Wiley & Sons, Ltd.     

Influence of the Curing Temperature in the Mechanical and Thermal Properties of Nanosilica Filled Epoxy Resin Coating

0.5–3 wt% nanosilica was added to an epoxy resin based on diglycidyl ether of bisphenol A (DGEBA) and cured at 25, 40 or 60 °C using isophoronediamine (IPDA) as hardener. Aggregates of nanosilica were properly dispersed into the DGEBA-IPDA resin and agglomerates formation was avoided. Addition of nanosilica increased the storage modulus E′ and the area and height of the tan δ curve of DGEBA-IPDA resin cured at 25 °C, but no significant differences were found by curing at higher temperature. Gel time measurements and the results obtained by applying the Kamal model to isotherm DSC curing of DGEBA-IPDA-nanosilica revealed that nanosilica catalysed the curing reaction between DGEBA and IPDA, in less extent by increasing the curing temperature.     

Synthesis and characterization of liquid‐crystalline epoxy and its blend with conventional epoxy

Terephthaloyl chloride was reacted with 4‐hydroxy benzoic acid to get terephthaloylbis(4‐oxybenzoic) acid, which was characterized and further reacted with epoxy resin [diglycidyl ether of bisphenol A (DGEBA)] to get a liquid‐crystalline epoxy resin (LCEP). This LCEP was characterized by Fourier transform infrared spectrometry, ¹H and ¹³C NMR spectroscopy, differential scanning calorimetry (DSC), and polarized optical microscopy (POM). LCEP was then blended in various compositions with DGEBA and cured with a room temperature curing hardener. The cured blends were characterized by DSC and dynamic mechanical analysis (DMA) for their thermal and viscoelastic properties. The cured blends exhibited higher storage moduli and lower glass‐transition temperatures (tan δ_max, from DMA) as compared with that of the pure DGEBA network. The formation of a smectic liquid‐crystalline phase was observed by POM during the curing of LCEP and DGEBA/LCEP blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3375–3383, 2003     

Synthesis and characterization of an epoxy based thermoset containing a fluorinated thermoplastic

A novel fluorinated thermoplastic (FT) was synthesized from diglycidyl ether of bisphenol A (DGEBA), and 3‐(trifluoromethyl)aniline. FT was found to be miscible with DGEBA as shown by the existence of a single glass transition temperature (T_g) within the whole composition range. On the basis of several experimental techniques, it was found that upon heating etherification reaction takes place between FT and DGEBA. A DGEBA‐aromatic diamine (4,4′‐methylenebis(3‐chloro 2,6‐diethylaniline) formulation was modified with the FT. The influence of FT on the epoxy‐amine kinetics was investigated. Both structural parameters, gelation, and vitrification, were found to be affected by etherification reaction between epoxy and hydroxyls groups belonging to FT. The presence of ether linkages induced system stoichiometry modification. In addition, the curing conditions influence on FT migration towards the surface was studied on samples prepared with 20 wt % of modifier. SEM–EDX analysis confirmed that modified systems exhibits notable fluorine enrichment within the uppermost 200 μm. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2781–2792, 2007     

Study of the physical aging of an epoxy/cycloaliphatic amine resin modified with abs

Using differential scanning calorimetry (DSC) we have studied the physical aging of an epoxy resin based on the diglycidyl ether of bisphenol A (DGEBA) modified by two different contents of an acrylonitrile-butadiene-styrene (ABS) and cured with 1,3-bisaminomethylcyclohexane (1,3-BAC). Samples fully cured were annealed at temperature of 125°C for periods of time of 72 and 120 h, to determine the process of physical aging. The apparent activation energy for the enthalpy relaxation, Dh*, is determined as the sample is heated at 10°C min^-1 following cooling at various rates through the glass transition region. DSC studies suggested that the presence of thermoplastic inhibits the process of relaxation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation and morphological,electrical, and mechanical properties of polyimide‐grafted MWCNT/polyimide composite

Precursor of polyimide, polyamic acid has been prepared sucessfully. Acid‐modified carbon nanotube (MWCNT) was grafted with soluble polyimide then was added to the polyamic acid and heated to 300 °C to form polyimide/carbon nanotube composite via imidation. Morphology, mechanical properties and electrical resistivity of the MWCNT/polyimide composites have been studied. Transmission electron microscope microphotographs show that the diameter of soluble polyimide‐grafted MWCNT was increased from 30–60 nm to 200 nm, that is a thickness of 70–85 nm of the soluble polyimide was grafted on the MWCNT surface. PI‐g‐MWCNT was well dispersed in the polymer matrix. Percolation threshold of MWCNT/polyimide composites has been investigated. PI‐g‐MWCNT/PI composites exhibit lower electrical resistivity than that of the acid‐modified MWCNT/PI composites. The surface resistivity of 5.0 phr MWCNT/polyimide composites was 2.82 × 10⁸ Ω/cm² (PI‐g‐MWCNT) and 2.53 × 10⁹ Ω/cm² (acid‐modified MWCNT). The volume resistivity of 5.0 phr MWCNT/polyimide composites was 8.77 × 10⁶ Ω cm (PI‐g‐MWCNT) and 1.33 × 10¹³ Ω cm (acid‐modified MWCNT).Tensile strength and Young's modulus increased significantly with the increase of MWCNT content. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3349–3358, 2007     

Novel flame‐retardant thermosets: Diglycidyl ether of bisphenol A as a curing agent of boron‐containing phenolic resins

Boron‐containing novolac resins were synthesized by the modification of a commercial novolac resin with different contents of bis(benzo‐1,3,2‐dioxaborolanyl)oxide. These novolac resins were crosslinked with diglycidyl ether of bisphenol A (DGEBA), and their thermal, thermodynamomechanical, and flame‐retardant properties were evaluated. The boron‐containing novolac resins were less thermally stable than the unmodified novolac resin. Their modification degree and DGEBA content were related to the crosslinking density of the materials. The boron‐containing novolac resins generated boric acid at high temperatures and gave an intumescent char that slowed down the degradation and prevented it from being total. They also showed good flame‐retardant properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1701–1710, 2006     

Novel quaternary ammonium borates as latent catalysts for epoxy–phenolic resins

Novel tetrabutylammonium tetrakis(substituted benzoyloxy)borate salts ( 1a – 1d ) were synthesized by the reaction of tetrabutylammonium tetraphenylborate and corresponding substituted benzoic acids. Polyaddition reactions of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐bisphenol F (44BPF) or bisphenol F (BPF‐D) with the ammonium borates were investigated as model reactions of epoxy/phenol–novolac resin systems with respect to the thermal latency and storage stability of the catalyst. The polyaddition of DGEBA/44BPF with the ammonium borates in diglyme at 150 °C for 6 h proceeded up to 84–94% conversions and gave polymers with number‐average molecular weights of 3750–5750, whereas the polyaddition at 80 °C for 6 h gave less than 9% conversions. The catalytic activity of ammonium borates 1a – 1d depended on the substituent of the phenyl group of the borates, and the order of activity was 1b (p‐OMe) > 1a (? H) > 1c (p‐NO₂) > 1d [3,5‐(NO₂)₂]. The ammonium borate catalyst with the substituent that yielded lower acidity of the corresponding substituted benzoic acid tended to reveal higher activity. In comparison with tetrabutylammonium bromide (TBAB) as a conventional ammonium salt, 1a – 1d revealed better thermal latency. The storage stability of DGEBA/BPF‐D with the ammonium borate catalysts in bulk at 40 °C was better than that with TBAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2689–2701, 2002     

Flame‐retardant epoxy resins with high glass‐transition temperatures. II. Using a novel hexafunctional curing agent: 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane

We synthesized a novel phosphorus‐containing triamine [9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane (dopo‐ta)] from the nucleophilic addition of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide and pararosaniline chloride, using triethylamine as an acid receiver. We confirmed the structure of dopo‐ta by IR, mass, and NMR spectra and elemental analysis. dopo‐ta served as a curing agent for diglycidyl ether of bisphenol A (DGEBA) and dicyclopentadiene epoxy (hp7200). Properties such as the glass‐transition temperature (T_g), thermal decomposition temperature, flame retardancy, moisture absorption, and dielectric properties of the cured epoxy resins were evaluated. The T_g's of cured DGEBA/dopo‐ta and hp7200/dopo‐ta were 171 and 190 °C, respectively. This high T_g phenomenon is rarely seen in the literature after the introduction of a flame‐retardant element. The flame retardancy increased with the phosphorus content, and a UL‐94 V‐0 grade was achieved with a phosphorus content of 1.80 wt % for DGEBA/dopo‐ta/diamino diphenylmethane (DDM) systems and 1.46 wt % for hp7200/dopo‐ta/DDM systems. The dielectric constants for DGEBA/dopo‐ta and hp7200/dopo‐ta were 2.91 and 2.82, respectively, implying that the dopo‐ta curing systems exhibited low dielectric properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5971–5986, 2005     

Multi-walled carbon nanotubes functionalized with triethylenetetramine as fillers to enhance epoxy dimensional thermal stability

Multi-walled carbon nanotubes (MWCNT) have been used as fillers to improve thermal properties such as glass transition temperature (T _g) of epoxy materials. In this work, nanocomposites based on diglycidyl ether of bisphenol A resin and triethylenetetramine (TETA) were prepared by a three-roll mill process with TETA-functionalized (MWCNT–COTETA) and neat MWCNT. Thermogravimetric analysis of the nanofillers showed that in the case of MWCNT–COTETA, there is a 15 % mass loss that can be attributed to –COTETA and residual oxygen-containing functional groups. The influence of chemical modification on the behavior of the glass T _g was evaluated by dynamic scanning calorimetry. The MWCNT–COTETA allowed a ~20 °C reproducible increase of T _g in concentrations in the range of 0.5–1.0 mass%. Furthermore, images obtained by scanning electron microscopy were used to investigate the morphology of the polymer matrix and its interfaces. The quality of the dispersion and interaction of the nanotubes in the epoxy matrix was assessed from the images. Both the neat epoxy and the nanocomposite with MWCNT showed low thermal shrinkage upon curing.     

Nonaqueous synthesis of nanosilica in epoxy resin matrix and thermal properties of their cured nanocomposites

Nonaqueous synthesis of nanosilica in diglycidyl ether of bisphenol‐A epoxy (DGEBA) resin has been successfully achieved in this study by reacting tetraethoxysilane (TEOS) directly with DGEBA epoxy matrix, at 80 °C for 4 h under the catalysis of boron trifluoride monoethylamine (BF₃MEA). BF₃MEA was proved to be an effective catalyst for the formation of nanosilica in DGEBA epoxy under thermal heating process. FTIR and ²⁹Si NMR spectra have been used to characterize the structures of nanosilica obtained from this direct thermal synthetic process. The morphology of the nanosilica synthesized in epoxy matrix has also been analyzed by TEM and SEM studies. The effects of both the concentration of BF₃MEA catalyst and amount of TEOS on the diameters of nanosilica in the DGEBA epoxy resin have been discussed in this study. From the DSC analysis, it was found that the nanosilica containing epoxy exhibited the same curing profile as pure epoxy resin, during the curing reaction with 4,4′‐diaminodiphenysulfone (DDS). The thermal‐cured epoxy–nanosilica composites from 40% of TEOS exhibited high glass transition temperature of 221 °C, which was almost 50 °C higher than that of pure DGEBA–DDS–BF₃MEA‐cured resin network. Almost 60 °C increase in thermal degradation temperature has been observed during the TGA of the DDS‐cured epoxy–nanosilica composites containing 40% of TEOS. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 757–768, 2006     

Synthesis and characterization of itaconic‐based epoxy resins

A trifunctional epoxy resin from itaconic acid (TEIA) was synthesized from a renewable resource‐based itaconic acid by allylation of itaconic acid to form diallyl itaconate by using m‐chloroperoxybenzoic acid as oxidizing agents followed by epoxidation of allylic C═C bond of diallyl itaconate methylhexahydropthalic anhydride as curing agent in the presence of 2‐methyl imidazole as a catalyst. The chemical structure of the synthesized resins was confirmed by Fourier transform infrared and nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR) spectroscopy analysis. The mechanical, thermal, and rheological performances of the TEIA were also investigated and compared with diglycidyl ether of bisphenol A and a plant‐based epoxidized soybean oil bioresin cured with the same curing agent. The higher epoxy value of 1.02, lower viscosity (0.96 Pa s at 25°C), higher mechanical, and higher curing reactivity toward methylhexahydropthalic anhydride of TEIA as compared with epoxidized soybean oil and comparable with diglycidyl ether of bisphenol A demonstrated significant evidence to design and develop a novel bio‐based epoxy resin with high performance to substitute the petroleum‐based epoxy resin.     

Poly(vinyltriethoxysilane) modified MWCNT/polyimide nanocomposites—Preparation,morphological, mechanical,and electrical properties

Multi‐walled carbon nanotube (MWCNT) modified by vinyltriethoxysilane (VTES) via free radical reaction has been prepared (poly (vinyltriethoxysilane) modified MWCNTs, PVTES‐MWCNT). Precursor of polyimide, polyamic acid has been synthesized by reacting 4,4′‐oxydianiline with 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride. PVTES‐MWCNT were then mixed with polyamic acid and heated to 300 °C to form CNT/polyimide composite. During the imidization processes, the silanes on CNT surface reacted with each other and may be connected together by covalent bond (Si? O? Si). The PVTES‐MWCNT was analyzed by Fourier transform infrared and X‐ray photoelectron spectroscopy. The PVTES‐MWCNT/polyimide composites were analyzed by CP/MAS solid state ²⁹Si nuclear magnetic resonance (NMR) spectroscopy. Morphological properties of the PVTES‐MWCNT/polyimide composites were investigated by scanning electron microscope and transmission electron microscope. Electrical conductivity increased dramatically comparing to the unmodified MWCNT/polyimide composites. Mechanical properties of nanocomposite were enhanced significantly by PVTES‐MWCNT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 803–816, 2008     

The POSS side chain epoxy nanocomposite: Synthesis and thermal properties

The IPI‐POSS‐modified epoxy resin (IPEP) was prepared from isocyanato‐propyldinethylsilyl‐isobutyl‐POSS (IPI‐POSS) and diglycidyl ether of bisphenol A epoxy resin. The steric hindrance of the IPEP bulky POSS side chain improved the curing activation energies. The POSS particles sizes were about 2–3 nm and dispersed uniformly. At lower IPEP concentration (POSS < 12 wt %), the glass transition temperatures (T_gs) of the IPEP nanocomposites increased from 118 to 170 °C. The char yield increased from 15 to 20 wt %, and the LOI values increased from 22 to 28. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 643–652, 2010     

Thermal latency of novel chelating borate catalysts as latent catalysts for epoxy–phenolic resins

Novel quaternary ammonium bis(2‐oxybenzoyloxy)borate salts ( 1a – 1c ) or quaternary ammonium bis(1,2‐benzenedioxy)borate salts ( 2a and 2b ) with tetra‐n‐butylammonium (TBA⁺), tetra‐n‐octylammonium (TOA⁺), or bis(triphenylphosphoranylidene)ammonium (PNP⁺) cations were synthesized as latent catalysts of epoxy/phenol–novolac resins by the complexation between boric acid and salicylic acid or catechol, followed by neutralization with quaternary ammonium hydroxide. Polyaddition reactions of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐bisphenol F (44BPF) or bisphenol F (BPF‐D) with the ammonium borates were investigated as model reactions of epoxy/phenol–novolac resin systems with respect to the thermal latency and storage stability of the catalyst. The polyaddition of DGEBA/44BPF with 1a – 1c in diglyme at 150 °C for 6 h proceeded up to 85–96% conversions and gave polymers with number‐average molecular weights of 4180–10,500, whereas the polyaddition at 80 °C for 6 h gave less than 8% conversions. However, the polyaddition with 2a containing TBA⁺ cation proceeded to only a 32% conversion at 150 °C for 6 h in diglyme and to a 64% conversion even at 180 °C for 6 h in triglyme and only gave low molecular weight oligomers, and no reaction proceeded in the polyaddition at 80 °C. However, polyaddition with 2b containing PNP⁺ cation proceeded up to a 96% conversion at 150 °C for 6 h in diglyme and gave a higher molecular weight polymer with a number‐average molecular weight of 8050, whereas the polyaddition at 80 °C for 6 h gave only a 5% conversion. The catalytic activity of ammonium borates 1a – 1c and 2a and 2b depended on the borate anion structure: 1a and 1c with bis(2‐oxybenzoyloxy)borate anion revealed higher activity than 2a and 2b with bis(1,2‐benzenedioxy)borate anion, respectively. In comparison with tetra‐n‐butylammonium bromide (TBAB) as a conventional ammonium salt or tetra‐n‐butylammonium tetrakis(benzoyloxy)borate (TBA‐TBB), 1a – 1c and 2b revealed better thermal latency. The catalytic activity of ammonium borates also depended on the bulkiness of the ammonium cation, and the order of activity was 1c (PNP⁺) > 1b (TOA⁺) ≧ 1a (TBA⁺) and 2b (PNP⁺) > 2a (TBA⁺). The storage stability of DGEBA/BPF‐D with the ammonium borate catalysts 1a – 1c and 2a and 2b in bulk at 40 °C was much better than that with TBAB and TBA‐TBB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2702–2716, 2002