A Highly Selective and Sensitive Barium(II)‐Selective PVC Membrane Based on Dimethyl 1‐Acetyl‐8‐oxo‐2,8‐dihydro‐ 1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate

A poly(vinyl chloride)‐based membrane of dimethyl 1‐acetyl‐8‐oxo‐2,8‐dihydro‐1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate as a neutral carrier with sodium tetraphenylborate (NaTPB) as an anion excluder and 2‐nitrophenyl octyl ether (NPOE) as plasticizer was prepared and investigated as a Ba(II)‐selective electrode. The electrode exhibits a Nernstian slope of 29.7±0.4 mV per decade over a wide concentration range (1.0×10^?6 to 1.0×10^?1 M) with a detection limit of 7.6×10^?7 M between pH 3.0 and 11.0. The response time of the sensor is about 10 s and it can be used over a period of 2 months without any divergence in potential. The proposed membrane sensor revealed good selectivity for Ba(II) over a wide variety of other metal ions. It was successfully used in direct determination of barium ions in industrial wastewater samples.     

Membrane Filtration of Iron(III), Copper(II) and Lead(II) Ions as 1‐(2‐Pyridylazo) 2‐Naphtol (PAN) for Their Preconcentration and Atomic Absorption Determinations

A membrane filtration procedure for the preconcentration and atomic absorption spectrometric determination of Pb(II), Co(II) and Fe(III) ions in natural water samples has been established. Cellulose nitrate membrane filters (0.45 μm and 47 mm diameter) were used in all experiments. The procedure is based on chelate formation of the analyte metals with 1‐(2‐pyridylazo) 2‐naphtol (PAN) and on retention of the chelates on cellulose nitrate membrane filter. The cellulose nitrate membrane and analyte ions were completely dissolved by 500 μL of nitric acid at 85 °C on a hood and then metal determinations were performed by flame atomic absorption spectrometry. The method was applied to natural water samples for the determination of analyte ions with satisfactory results, e.g., recoveries > 95%, RSD's < 10%.     

Silica‐bonded S‐sulfonic Acid as a Recyclable Catalyst for Synthesis of 2,3‐Dihydroquinazolin‐4(1H)‐ones

2,3‐Dihydroquinazolin‐4(1H)‐one derivatives were synthesized via a one‐pot, three component reaction of isatoic anhydride and an aromatic aldehyde with ammonium acetate or primary amine catalyzed by silica‐bonded S‐sulfonic acid in ethanol at 80°C. The reaction work‐up is simple and the catalyst is easily separated from the products by filtration. The heterogeneous catalyst was recycled for ten runs upon the condensation reaction of isatoic anhydride and 4‐chlorobenzaldehyde with ammonium acetate without losing its catalytic activity.     

Mono‐ and difluorinated 1,1,2,2,9,9,10,10‐octafluoro[2.2]paracyclophanes (AF4s)—A 1H and 19F NMR study

Complete assignment of the ¹H and ¹⁹F chemical shifts in 4‐fluoro‐AF4 (1) were based on the nOes seen in its ¹⁹F‐¹H HOESY spectrum. This allowed for identification of features which can further be applied to the assignment of the regiochemistry of substituted perfluoroparacyclophanes (PCPs) and AF4s: (i) an aromatic fluorine couples with the two fluorines in the closest bridge that are syn to it, with constants of ca. 20 Hz; (ii) an aromatic fluorine couples with the bridge fluorine five bonds away that is anti to it in the same paraphenylene moiety, with a constant of ca. 3.5 Hz; (iii) the geminal coupling of the bridge fluorines is 246 Hz if they have an ortho fluorine and 238 Hz if they do not; (iv) a bridge fluorine couples with those aromatic protons in the same paraphenylene moiety that are four or five bonds away and anti. These features have been used to assign the regiochemistry of the pseudo‐ortho, pseudo‐meta and pseudo‐para‐difluoro AF4s 2–4. It has also been demonstrated that SCS for the bridge fluorines can be used as well for this assignment. Copyright © 2009 John Wiley & Sons, Ltd.     

Non‐Isothermal Decomposition Kinetics,Specific Heat Capacity and Adiabatic Time‐to‐explosion of a Novel High Energy Material: 1‐Amino‐1‐Methylamino‐2,2‐Dinitroethylene (AMFOX‐7)

A novel high energy material, 1‐amino‐1‐methylamino‐2,2‐dinitroethlyene (AMFOX‐7), was synthesized by the reaction of 1,1‐diamino‐2,2‐dinitroethylene (FOX‐7) and methylamine aqueous solution in N‐methyl pyrrolidone at 80°C. The thermal behavior and non‐isothermal decomposition kinetics of AMFOX‐7 were studied with DSC and TG/DTG methods. The kinetic equation of thermal decomposition reaction can be expressed as: $ {\rm d\alpha /d}T = \frac{{10^{21.03}}}{{\rm \beta}}\frac{3}{2}\left({1 - {\rm \alpha}} \right)\left[{- 1{\rm n}\left({{\rm 1} - {\rm \alpha}} \right)} \right]^{\frac{1}{3}} \exp \left({- 2.292 \times 10^5 {\rm /}RT} \right) A novel high energy material, 1‐amino‐1‐methylamino‐2,2‐dinitroethlyene (AMFOX‐7), was synthesized by the reaction of 1,1‐diamino‐2,2‐dinitroethylene (FOX‐7) and methylamine aqueous solution in N‐methyl pyrrolidone at 80°C. The thermal behavior and non‐isothermal decomposition kinetics of AMFOX‐7 were studied with DSC and TG/DTG methods. The kinetic equation of thermal decomposition reaction can be expressed as: $ {\rm d\alpha /d}T = \frac{{10^{21.03}}}{{\rm \beta}}\frac{3}{2}\left({1 - {\rm \alpha}} \right)\left[{- 1{\rm n}\left({{\rm 1} - {\rm \alpha}} \right)} \right]^{\frac{1}{3}} \exp \left({- 2.292 \times 10^5 {\rm /}RT} \right) $. The critical temperature of thermal explosion of AMFOX‐7 is 244.89°C. The specific heat capacity of AMFOX‐7 was determined with micro‐DSC method and theoretical calculation method, and the standard molar specific heat capacity is 199.39 J·mol^?1·K^?1 at 298.15 K. Adiabatic time‐to‐explosion of AMFOX‐7 was also calculated to be 215.41 s. AMFOX‐7 has higher thermal stability than FOX‐7.     

A comparative study of two polymorphs of bis(1‐hydroxy‐2‐methylpropan‐2‐aminium) carbonate

Alkanolamines have been known for their high CO₂ absorption for over 60 years and are used widely in the natural gas industry for reversible CO₂ capture. In an attempt to crystallize a salt of (RS)‐2‐(3‐benzoylphenyl)propionic acid with 2‐amino‐2‐methylpropan‐1‐ol, we obtained instead a polymorph (denoted polymorph II) of bis(1‐hydroxy‐2‐methylpropan‐2‐aminium) carbonate, 2C₄H₁₂NO⁺·CO₃²⁻, (I), suggesting that the amine group of the former compound captured CO₂ from the atmosphere forming the aminium carbonate salt. This new polymorph was characterized by single‐crystal X‐ray diffraction analysis at low temperature (100 K). The salt crystallizes in the monoclinic system (space group C2/c, Z = 4), while a previously reported form of the same salt (denoted polymorph I) crystallizes in the triclinic system (space group P, Z = 2) [Barzagli et al. (2012). ChemSusChem, 5 , 1724–1731]. The asymmetric unit of polymorph II contains one 1‐hydroxy‐2‐methylpropan‐2‐aminium cation and half a carbonate anion, located on a twofold axis, while the asymmetric unit of polymorph I contains two cations and one anion. These polymorphs exhibit similar structural features in their three‐dimensional packing. Indeed, similar layers of an alternating cation–anion–cation neutral structure are observed in their molecular arrangements. Within each layer, carbonate anions and 1‐hydroxy‐2‐methylpropan‐2‐aminium cations form planes bound to each other through N—H…O and O—H…O hydrogen bonds. In both polymorphs, the layers are linked to each other via van der Waals interactions and C—H…O contacts. In polymorph II, a highly directional C—H…O contact (C—H…O = 156°) shows as a hydrogen‐bonding interaction. Periodic theoretical density functional theory (DFT) calculations indicate that both polymorphs present very similar stabilities.     

Pulsed‐laser–deposited and plasma‐polymerized polytetrafluoroethylene (PTFE)‐like thin films: A comparative study on PTFE‐specific properties

Glass‐like and structural first‐order phase transitions are investigated in polytetrafluoroethylene (PTFE) foils and PTFE‐like films prepared by pulsed‐laser deposition (PLD) and plasma polymerization (PP). A structural comparison of the investigated polymers is performed by infrared spectroscopy and dielectric dilatometry. It is shown that dielectric dilatometry (the measurement of the susceptance vs. temperature) provides a simple and elegant means for detecting volumetric transitions in thin nonpolar polymer films. In conventional PTFE foils, the known glass‐like and structural first‐order phase transitions are identified. The structure of pulsed‐laser deposited PTFE strongly depends on the target material, ranging from highly crystalline films showing only structural phase transitions to films strongly deviating from PTFE foils, with structural characteristics comparable to plasma‐polymerized fluorocarbons. The dielectric loss of the highly crystalline PLD films compares favorably with conventional PTFE foils, making the films attractive for new applications in miniature electret devices. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2115–2125, 1999     

Novel Regioselective Synthesis and Biological Activity of 6‐Phenylazo and 3,6‐Bis(arylazo)‐7‐hydroxy‐1H‐[1,2,4]triazolo[4,3‐a]pyrimidin‐5(4H)‐one

Treatment of 6‐hydroxy‐5‐phenylazo‐2‐thioxo‐4(1H)‐pyrimidinone 1 with a series of hydrazonoyl halides 2 and N,2‐diaryl‐diazinecarbohydrazonoyl halides 9 in dioxane in the presence of triethylamine under reflux furnishes 6‐phenylazo and 3,6‐bis(arylazo)‐7‐hydroxy‐1H‐[1,2,4]triazolo[4,3‐a]pyrimidin‐5(4H)‐one derivatives 7 and 10 , respectively. The biological activities of the products were evaluated.     

Synthesis of 6‐Aminoindolo[2,1‐a]isoquinoline‐5‐carbonitriles by the Cu‐Catalyzed Reaction of 2‐(2‐Bromophenyl)‐1H‐indoles with CH2(CN)2

A series of 6‐aminoindolo[2,1‐a]isoquinoline‐5‐carbonitriles 4 have been prepared by treatment of 2‐(2‐bromophenyl)‐1H‐indoles 1 , available from 1‐(2‐bromophenyl)ethanones or 1‐(2‐bromophenyl)propan‐1‐ones by using Fischer indole synthesis, with propanedinitrile in the presence of a catalytic amount of CuBr and an excess of K₂CO₃ in DMSO at 100°.     

Influence of deformation on irreversible and reversible crystallization of poly(ethylene‐co‐1‐octene)

The effect of uniaxial deformation and subsequent relaxation at ambient temperature on irreversible and reversible crystallization of homogeneous poly(ethylene‐co‐1‐octene) with 38 mol % 1‐octene melt‐crystallized at 10 K min was explored by calorimetry, X‐ray scattering, and Fourier transform infrared spectroscopy. At 298 K, the enthalpy‐based crystallinity of annealed specimens increased irreversibly by stress‐induced crystallization from initially 15% to a maximum of, at least, 19% when a permanent set of more than 200% was attained. The crystallinity increased by formation of crystals of pseudohexagonal structure at the expense of the amorphous polymer, and as a result of destruction of orthorhombic crystals. The stress‐induced increase of crystallinity was accompanied by an increase in the apparent specific heat capacity from 2.44 to about 2.59 J g^?1 K^?1, which corresponds to an increase of the total reversibility of crystallization from, at least, 0.10 to 0.17% K^?1. The specific reversibility calculated for 100% crystallinity increased from 0.67 to 0.89% K^?1 and points to a changed local equilibrium at the interface between the crystal and amorphous phases. The deformation resulted in typical changes of the phase structure and crystal morphology that involve orientation and destruction of crystals as well as the formation of fibrils. The effect of the decrease of the entropy of the strained melt on the reversibility of crystallization and melting is discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1223–1235, 2002     

Synthesis of a Ruthenium(II) Compound based on 5‐(2‐Pyrimidyl)‐1H‐tetrazole for Photodynamic Therapy

Ru^II compounds have been universally investigated due to their unique physical and chemical properties. In this paper, a new Ru^II compound based on 2,2′‐bipy and Hpmtz [2,2′‐bipy = 2,2′‐bipyridine, Hpmtz = 5‐(2‐pyrimidyl)‐1H‐tetrazole], namely [Ru(2,2′‐bipy)₂(pmtz)][PF₆] · 0.5H₂O was prepared and characterized by elemental analysis, IR and single‐crystal X‐ray diffraction. [Ru(2,2′‐bipy)₂(pmtz)][PF₆] · 0.5H₂O shows a mononuclear structure and forms a three‐dimensional network by non‐classic hydrogen bonds. The ability of generation of ROS (reactive oxygen species) makes it has a low phototoxicity IC₅₀ (half‐maximal inhibitory concentration) after Xenon lamp irradiation on Hela cells in vitro. The results demonstrate that [Ru(2,2′‐bipy)₂(pmtz)][PF₆] · 0.5H₂O with high light toxicity and low dark toxicity may be a potential candidate for photodynamic therapy.     

Efficient Synthesis of 2‐(2‐Aminophenyl)‐2,3‐dihydropyridin‐4(1H)‐ones Based on a Cyclization/Ring Cleavage Procedure

(Benzyloxycarbonyl)‐protected 3,4‐benzo‐7‐hydroxy‐2,9‐diazabicyclo[3.3.1]non‐7‐enes were prepared by one‐pot cyclizations of 1,3‐bis(silyl enol ethers) with quinazolines. Subsequent hydrogenation resulted in one‐pot deprotection and rearrangement to give 2‐(2‐aminophenyl)‐2,3‐dihydropyridin‐4(1H)‐ones.     

Synthesis and characterization of poly(higher‐α‐olefin)s with a nickel(α‐diimine)/methylaluminoxane catalyst system: Effect of chain running on the polymer properties

Homopolymerization of octadecene‐1 at different reaction conditions has been studied. Significant chain running can be seen at higher polymerization temperatures. Interestingly, insertion of octadecene‐1 into a sterically hindered nickel‐cation/carbon (secondary) bond is observed. The microstructure of the polymer was established using NMR spectroscopy. The effects of chain running on polymer melting, crystallization behavior, and dynamic mechanical thermal properties were studied using DSC and DMTA. The extent of chain running (i.e., 2,ω‐, 1,ω‐enchainments) decreases with an increase in the carbon number of α‐olefins. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 191–210, 2007     

Chemisorption of thiol‐functionalized metallocene molecules on Si(111)‐ Ag√3×√3 surface: A density functional theory study

Herein, chemical adsorption properties of the thiol‐functionalized metallocene molecules [M(C₅H₄SH)₂] on Si(111)‐Ag√3×√3 surface were investigated using density functional theory calculation. For this purpose, thiol‐modified ferrocene [Fe(C₅H₄SH)₂], osmocene [Os(C₅H₄SH)₂], and ruthenocene [Ru(C₅H₄SH)₂] molecules were attached on the surface via two different binding models. The more favorable chemical binding energies of [Fe(C₅H₄SH)₂], [Os(C₅H₄SH)₂], and [Ru(C₅H₄SH)₂] molecules were calculated as ?3.42, ?2.15, and ?2.00 eV, respectively. The results showed that the adsorption energies of metallocene molecules change independently by increasing the radius of metal ions where on going down the group of the periodic table. The calculated adsorption energies showed that [Fe(C₅H₄SH)₂] molecule was more stable on the Si(111)‐Ag√3×√3 surface. By calculating the electronic band structure for metallocene/Si(111)‐Ag√3×√3 surfaces, we identified a flat dispersion band in a part of the surface Brillouin zone. © 2015 Wiley Periodicals, Inc.     

Perchloric Acid–Silica (HClO4⋅SiO2)‐Catalyzed Synthesis of 14‐Alkyl‐ or 14‐Aryl‐14H‐dibenzo[a,j]xanthenes and N‐[(2‐Hydroxynaphthalen‐1‐yl)methyl]amides

The synthesis of 14‐aryl‐ or 14‐alkyl‐14H‐dibenzo[a,j]xanthenes 3 involving the treatment of naphthalen‐2‐ol ( 1 ) with arenecarboxaldehydes or alkanals 2 in the presence of HClO₄?SiO₂ as a heterogeneous catalyst was achieved (Table 1), and this reaction was extended to the preparation of N‐[(2‐hydroxynaphthalen‐1‐yl)methyl]amides 5 by a three‐component reaction with urea ( 4a ) or an amide 4b – d as a third reactant (Table 2).     

Plane‐wave density functional theory investigation of adsorption of 2,4,6‐trinitrotoluene on al‐hydroxylated (0001) surface of (4 × 4) α‐alumina

This article reports the results of the theoretical investigation of adsorption of 2,4,6‐trinitrotoluene (TNT) on Al‐hydroxylated (0001) surface of (4 × 4) α‐alumina (α‐Al₂O₃) using plane‐wave Density Functional Theory. Sixteen water molecules were used to hydroxylate the alumina surface. The Perdew–Burke–Ernzerhof functional and the recently developed van der Waals functional (vdW‐DF2) were used. The interaction of electron with core was accounted using the Vanderbilt ultrasoft pseudopotentials. It was found that hydroxylation has significant influence on the geometry of alumina and such changes are prominent up to few layers from the surface. Particularly, due to the Al‐hydroxylation the oxygen layers are decomposed into sublayers and such partitioning becomes progressively weaker for interior layers. Moreover, the nature of TNT adsorption interaction is changed from covalent type on the pristine alumina surface to hydrogen‐bonding interaction on the Al‐hydroxylated alumina surface. TNT in parallel orientation forms several hydrogen bonds compared to that in the perpendicular orientation with hydroxyl groups of the Al‐hydroxylated alumina surface. Therefore, the parallel orientation will be present in the adsorption of TNT on Al‐hydroxylated (0001) surface of α‐alumina. Further, the vdW‐DF2 van der Waals functional was found to be most suitable and should be used for such surface adsorption investigation. © 2014 Wiley Periodicals, Inc.     

A One‐Pot Synthesis of 1,3‐Dihydro‐1,3,3‐tris(perfluoroalkyl)isobenzofuran‐1‐olates and Their Complete NMR Spectroscopic Analysis on the Basis of 1D and 2D Experiments

A convenient synthesis of the 1,3‐dihydro‐1,3,3‐tris(perfluoroalkyl)isobenzofuran‐1‐ols 3a , b was elaborated starting from commercially available phthaloyl dichloride and trimethyl(perfluoroalkyl)silanes (Me₃SiR_f) 1a , b (R_f=CF₃, C₂F₅) in the presence of a fluoride source (Schemes 1 and 3). In a reaction analogous to alkyl Grignard reagents, double chloride substitution by two perfluoroalkyl groups and subsequent addition of one perfluoroalkyl group with concomitant ring closure led to this new class of compounds (Scheme 2). The syntheses of the alcohols and some alcoholates, as well as of the corresponding trimethylsilyl ethers are described. A combination of special 1D and 2D NMR experiments allowed the assignment of all atoms of the new compounds. The solid‐state structure of 1,3‐dihydro‐1,3,3‐tris(trifluoromethyl)isobenzofuran‐1‐ol ( 3a ) was elucidated by X‐ray diffraction methods.     

Functionalization of diamond (001)‐2 × 1 surface by cycloaddition of 1,3‐cyclohexadiene: A theoretical study

Density functional theory calculations have been used to study [4 + 2] and [2 + 2] cycloaddition reaction between 1,3‐cyclohexadiene and diamond (001)‐2 × 1 surface. The calculations revealed four possible reaction pathways for 1,3‐cyclohexadiene with the surface dimmers of diamond. Full geometry‐optimized structures were obtained for all products, including intradimer and interdimer reaction products. These results were analyzed both in terms of the total energy values and the detailed optimized geometries. We found that the intradimer [4 + 2] product is energetically favored over the other products, and the barrier to intradimer [4 + 2] addition is lower than the other additions, so the intradimer [4 + 2] product is expected to be the dominant product on the surface. © 2009 Wiley Periodicals, Inc. Int J Quantum Chem, 2010     

Simple magnetization of Fe3O4/MIL‐53(Al)‐NH2 for a rapid vortex‐assisted dispersive magnetic solid‐phase extraction of phenol residues in water samples

The present work describes a simple route to magnetize MIL‐53(Al)‐NH₂ sorbent for rapid extraction of phenol residues from environmental samples. To extend the applications and performances of the metal‐organic frameworks in the field of adsorption materials, we combined the properties of metal‐organic frameworks and magnetite to decrease the extraction time and simplify the extraction process as well. In this study, a simple and quick vortex‐assisted dispersive magnetic solid phase extraction method for the extraction of ten United States Environmental Protection Agency's priority phenols from water samples prior to analysis by high‐performance liquid chromatography with photodiode array detection was proposed. The developed method exhibits a rapid enrichment of the target analytes within 10 s for extraction and 10 s for desorption. Low detection limits of 1.8‐41.7 µg/L and quantitation limits of 6.0‐139.0 µg/L with the relative standard deviations for intra‐ and interday analyses less than 12% were achieved. Satisfactory recoveries in the range of 80‐111% with the relative standard deviations less than 11% demonstrated that Fe₃O₄/MIL‐53(Al)‐NH₂ is promising sorbent in the field of magnetic solid‐phase extraction for environmental samples.     

1H{15N} GHMQC study of 5,7‐diphenyl‐1,2,4‐triazolo[1,5‐a]pyrimidine and 1H, 13C and 15N NMR coordination shifts in Au(III) chloride complexes of 1,2,4‐triazolo[1,5‐a]pyrimidines

The ¹H{¹⁵N} NMR spectrum of 5,7‐diphenyl‐1,2,4‐triazolo[1,5‐a]‐pyrimidine ( 3 ) was measured by GHMQC, unambiguously assigned and compared with the spectra of 1,2,4‐triazolo[1,5‐a]pyrimidine ( 1 ) and 5,7‐dimethyl‐1,2,4‐triazolo[1,5‐a]pyrimidine ( 2 ). A series of Au(III) chloride complexes of general formula AuLCl₃, where L = 1 , 2 , 3 , was synthesized and studied by ¹HH{¹⁵N} GHMQC and ¹H{¹³C} GHMBC. Low‐frequency shifts of 72–74 ppm (¹⁵N) and 5–6 ppm (¹³C) were observed upon complexation by Au(III) ions for the coordination site N‐3 and adjacent C‐2, C‐3a atoms, respectively. The ¹³C signals of C‐5, C‐6, C‐7 and the ¹H resonances of H‐2, H‐6 were shifted to higher frequency. Comparison with analogous Pd(II), Pt(II) and Pt(IV) complexes revealed that in the case of Au(III) coordination the ¹⁵N shifts were relatively smaller, whereas those for ¹³C and ¹H were larger. Copyright © 2002 John Wiley & Sons, Ltd.