Shape memory effect and reversible phase crystallization process in SMPU ionomer

It is the first attempt to reveal the effect of reversible phase crystallization process on shape memory effect in shape memory polyurethane (PU) ionomer. Thereof the cyclic tensile testing was conducted with various cooling time to fix the temporary deformation for assessing shape memory function. The crystallization process of the reversible phase, poly (ε‐caprolactone) (PCL) in shape memory PU ionomers composed of different ionic group contents, 1,4‐butanediol, 4,4′‐methylenebis(phenyl isocyanate) and PCL, was investigated by using isothermal crystallization kinetics under the thermal routine similar to that for the cyclic tensile testing. The results demonstrate that the ionic groups within hard segments significantly slow down the crystal growth of the reversible phase. When the physical crosslink is strong enough, the crystallization rate would be a predominant factor determining the shape fixity ratio after various cooling time. Instead, when physical crosslink is weakening, the influence of crystallization rate is much less on the cooling time dependence of fixity. Copyright © 2007 John Wiley & Sons, Ltd.     

Investigation into stress recovery behavior of shape memory polyurethane fiber

In this work, the stress recovery behavior of shape memory polyurethane (SMPU) fiber was investigated. The as‐spun SMPU fibers were subjected to various programing‐recovery conditions. It was observed that recovering at 100 °C generated higher recovery stress than recovering at 150 °C. It was also found that, while hot‐drawn programed fiber has higher recovery stress than cold‐drawn programed fiber if recovered at 100 °C, cold‐drawn programed fiber has higher stabilized recovery stress than hot‐drawn programed counterpart when recovered at 150 °C. A morphological model was proposed based on the results from differential scanning calorimetry, Fourier transform infrared spectrometry, and X‐ray diffraction to understand the physics behind the different stress recovery behaviors. It is found that SMPU experiences different phase transitions and phase separations under different programing and stress recovery conditions. It is concluded that the two sequential phase separations taking place at 100 and 150 °C are primarily responsible for the differences in the stress recovery behavior. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1429–1440     

A study of fluorescent‐dye polyurethane ionomer 1

The reaction of toluene diisocyanate with 4‐hydroxycoumarin or 7‐hydroxycoumarin or dicumarol and other additives to form the structure of fluorescent‐dye polyurethane ionomer, which has been successfully synthesized at our laboratary, is demonstrated by Fourier transform infrared spectra. The fluorescence study of coumarins present in N,N‐dimethyl acetamide indicates that these coumarins form aggregations and exhibit fluorescence at around 304 nm. The experimental results show that the surface tension of 4‐hydroxycoumarin or 7‐hydroxycoumarin in N,N‐dimethylacetamide appears to decrease with increasing concentration of 4‐hydroxycoumarin or 7‐hydroxycoumarin. On the other hand, the surface tension of dicumarol in N,N‐dimethylacetamide increases with increasing concentration of dicumarol, indicating that increased hydrophilic groups of dicumarol adsorbed at the surface of N,N‐dimethylacetamide become even more ordered. For fluorescent‐dye polyurethane ionomer in aqueous solution, the number average particle sizes are seen to increase with an increase of coumarin concentration. Since the intermolecular interaction between hydrophilic groups of fluorescent‐dye polyurethane ionomer molecules themselves may become strong, therefore, the free volume of these ionomer molecules are considered to be increased significantly. This may be why the number average particle size becomes large. For self‐cured films made by fluorescent‐dye polyurethane ionomer, the tensile strength is seen to increase with increasing concentration of coumarin, as a result of increased crosslinking resulting from increased hydrophilic groups of coumarins attached to the backbone of the ionomer molecules. The elongation of self‐cured film made by dicumarol‐based polyurethane iomomer, on the other hand, decreases with increasing concentration of dicumarol. Copyright © 2000 John Wiley & Sons, Ltd.     

Study on poly(ε‐caprolactone)‐based shape memory copolymer fiber prepared by bulk polymerization and melt spinning

In this paper, a poly(ε‐caprolactone) (PCL)‐based shape memory polyurethane fiber was prepared by melt spinning. The shape memory switching temperature was the melting transition temperature of the soft segment phase mainly composed of PCL at 47°C. The mechanical properties especially shape memory effect were explicitly characterized by thermomechanical cyclic tensile testing. The results suggest that the prepared fiber has shape memory effects. The prepared 40 denier shape memory fiber had a tenacity of about 1.0 cN/dtex, and strain at break 562–660%. The shape fixity ratio reached 84% and the recovery ratio reached 95% under drawing at high temperature and thermal recovery testing.¹ Finally, the fiber thermal/mechanical properties were measured using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Copyright © 2007 John Wiley & Sons, Ltd.     

Waterborne polyurethane nanocomposites having shape memory effects

UV curable waterborne polyurethane/silica nanocomposites were designed and synthesized with functionalized silicas, where the functionalization was made with allyl isocyanate. The incorporated silica particles gave triple effects of multifunctional chemical cross‐links, reinforcing fillers, and stress relaxation retarders. Consequently, functionalized silica incorporated into the polymer chains showed significantly improved mechanical and thermal properties than the simple addition of unmodified silica. Notably, over 99% shape fixity and shape recovery with minimum cyclic hysteresis were obtained for the repeated cycles at 1% loading of the modified silica. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Water vapor permeability of shape memory polyurethane with amorphous reversible phase

Shape memory thermoplastic polyurethanes (TPUs), based on amorphous soft segment from the reaction of hexamethylene diisocyanate and 1,2‐butane diol, and the crystalline hard segment from 4,4′‐methylenediphenyl diisocyanate and 1,6‐hexanediol, were modified by hydrophilic segments, diol‐terminated poly(ethylene oxide) or dimethylol propionic acid (DMPA). Differential scanning calorimetry, dynamic mechanical testing, tensile testing, and the measurement of shape memory effect, water swell, and water vapor permeability were carried out to examine these TPUs. The hydrophilic segment increased the hysterisis in shape memory effect by reducing the crystallinity of the hard segment. The neutralized DMPA unit enhanced the sensitivity of the thermoresponsive water vapor permeability (WVP) by amplifying the increase of WVP at the temperature range above the glass transition temperature. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3009–3017, 2000     

The ionic conductive property of sulfonated polyethylene oxide polyurethane ionomers

A series of lithium and sodium salts of sulfonated polyethylene oxide (PEO) polyurethane ionomers in different levels of ionization were prepared. It has been found that this material is a new type of ionic conductive polymer, characterized by a single-ion transport mechanism and good mechanical properties. The ionization level significantly influences the ionic conductivity of the samples. When the mole ratio of the metal ion and ether oxygen atom is about 0.05, the ionomers exhibit maximum cationic conductivity. An optimal cationic conductivity of 1.0 × 10^?5 S/cm is obtained at about 70°C without any addition of organic plasticizer. The conductivity increases apparently when propylene carbonate and low MW PEO are added to the polyurethane ionomer. © 1995 John Wiley & Sons, Inc.     

Shape memory biomaterials prepared from polyurethane/ureas containing sulfated glucose

Covalently crosslinked polyurethane/urea polymers were synthesized using diamine monomers modified with pendant glucose groups and 2,4‐toluene diisocyanate, poly(ethylene glycol) (PEG), and 1,1,1‐tris(hydroxymethyl)ethane (triol) comonomers. The polymers showed shape memory behavior with a switching temperature dependent on the glass transition temperature. The glass transition temperature is tuned by varying the mole ratio between the glucose‐diamine and PEG used in the polymerization. Increasing PEG content resulted in decreasing glass transition temperature, and a glass transition temperature of 39 °C, close to physiological temperatures, was obtained. The fixed shape showed gradual shape recovery behavior, but a fixity of 70% was achieved when the material was stored at 25 °C. The polymer recovered to the permanent shape when heated to 50 °C. Finally, the surface of a film of the polymer can be sulfated to achieve increased blood‐compatibility without sacrificing the shape memory properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2252–2257     

Ultra low density and highly crosslinked biocompatible shape memory polyurethane foams

We report the development of highly chemically crosslinked, ultra low density (～0.015 g/cc) polyurethane shape memory foams synthesized from symmetrical, low molecular weight, and branched hydroxyl monomers. Sharp single glass transitions (T_g) customizable in the functional range of 45–70 °C were achieved. Thermomechanical testing confirmed shape memory behavior with 97–98% shape recovery over repeated cycles, a glassy storage modulus of 200–300 kPa, and recovery stresses of 5–15 kPa. Shape holding tests under constrained storage above the T_g showed stable shape memory. A high volume expansion of up to 70 times was seen on actuation of these foams from a fully compressed state. Low in vitro cell activation induced by the foam compared with controls demonstrates low acute bio‐reactivity. We believe these porous polymeric scaffolds constitute an important class of novel smart biomaterials with multiple potential applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Phase morphology and molecular dynamics of a polyurethane ionomer reinforced with a liquid crystalline filler

Solution-blended binary composites of ionic segmented polyurethane (SPU-I) and liquid crystalline oligomer (LCO) were characterized by wide-angle (WAXS) and small-angle (SAXS) X-ray scattering, differential scanning calorimetry (DSC), thermally stimulated depolarization currents (TSDC) and dielectric relaxation spectroscopy (DRS).Both components mutually influenced their states of aggregation in blends (most significantly, promoting smearing-out of interfaces between stiff and soft chain fragments of SPU-I into broad interfacial regions of intermediate composition). Apparently, the blend with w=0.10 happened to be most favorable for crystallization of the LCO, while the degree of microphase separation for SPU-I became lower and the distribution of stiff domains by sizes became broader, the higher the LCO content. The overall molecular mobility of SPU-I in blends was significantly reduced. This reduction included the intensity of the secondary and the primary relaxations, and of the interfacial Maxwell-Wagner-Sillars (MWS) relaxation, whereas the transition temperatures remained essentially composition-invariant. The Arrhenius-like behavior for the dc conductivity concomitant to the non-Arrhenius (i.e., Vogel-Tammann-Fulcher) frequency dependence for the α relaxation in blends suggested a decoupling of conductivity from the motion of the SPU-I soft chain segments.     

Short Twaron aramid fiber reinforced thermoplastic polyurethane

Mechanical, dynamic mechanical, and rheological behaviors of a short p‐aramid fiber reinforced thermoplastic polyurethane (TPU) have been studied in the range of 0–30 wt% of fibers. The tensile strength of the composite is improved slightly at higher fiber content with a minimum at around 10 wt% of fibers. The addition of fibers markedly reduces elongation at break and entails a steady increase in the elastic modulus, but decreases the wear resistance of the matrix. Storage modulus (E′) is increased and the shapes of loss tangent (tan δ) peaks point to a possible fiber–matrix interaction. Rheological studies show a power law behavior for all composites and increased viscosity with fiber loading. Study of the tensile and cryogenic fracture surfaces by scanning electron microscopy (SEM) indicates good correlation between the modes of failure and strength of the composites. The micrographs reveal good interfacial adhesion and extensive peeling and fibrillation of the fibers in the compounded and fractured composites. Theoretical models have been used to fit the experimental modulus data. Copyright © 2008 John Wiley & Sons, Ltd.     

Shape memory natural rubber

Charles Goodyear discovered the vulcanization of natural rubber (NR) 170 years ago and transferred the gooey natural compound into the first representative of an entirely new class of materials; the elastomers. Thenceforth, NR was intensively explored and was used for countless products to date. All the more surprising, it was found recently that NR exhibits superior and unexpected properties whenever it is cross-linked to a degree smaller than 0.4% which is fairly below the commonly used 1%–2%. This article gives a brief overview on the exceptional properties of lightly cross-linked NR, named shape memory natural rubber (SMNR), including the cold programmable shape memory effect, storing of extremely large strain, energy and cold, and its capability to sense and memorize environmental parameters. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1381–1388     

Bio‐based hyperbranched polyurethane/Fe3O4 nanocomposites as shape memory materials

The bio‐based shape memory polymers have generated immense interest as advanced smart materials. Mesua ferrea L. seed oil‐based hyperbranched polyurethane (HBPU)/Fe₃O₄ nanocomposites were prepared by the in‐situ polymerization technique. The transmission electron microscopy confirmed the homogeneous distribution of the Fe₃O₄ nanoparticles in polymer matrix, whereas Fourier transform infrared spectroscopic study revealed the presence of strong interfacial interactions between them. The incorporation of Fe₃O₄ (0 to 10 wt%) into the HBPU resulted in an increase in tensile strength (5.5–15 MPa) and scratch resistance (3–6 kg). The thermo‐gravimetric analysis indicated the improvement of thermal stability (240–270°C) of the nanocomposites. The nanocomposites exhibited full shape fixity, as well as almost full shape recovery under the microwave stimulus. The shape recovery speed increased with the increase of Fe₃O₄ nanoparticles content in the nanocomposites. Thus, the studied nanocomposites might be used as advanced shape memory materials in different potential fields. Copyright © 2013 John Wiley & Sons, Ltd.     

Triple shape memory effect in multiple crystalline polyurethanes

Remembering more than one permanent shape is an attractive research topic for shape memory materials (SMMs). In this paper, multiple crystalline shape memory polyurethanes (SMPUs) are prepared with PCL10000 and PTMG2900 by a three‐step polymerization method. DSC and WAXD results show that the obtained polyurethane contains, simultaneously and independently, two kinds of crystals. In addition, it is confirmed through DMA analysis that reversible soft phase and hard domains are formed in the PCL‐PTMG based SMPU system; and two‐step modulus decreases at low temperature range can be obtained in the SMPU with suitable mass proportion of PCL to PTMG, e.g., 1:7. Thus, shape memory effect (SME) can be achieved in this system. Moreover, it is found that the PTMG soft segment dominates the shape memory effect when the PCL mass is lower than that of PTMG; while the PCL soft segment dominates the SME when PCL mass is higher than that of PTMG; and a two‐step programing shape recovery can be achieved when the mass proportion of PCL/PTMG reaches a balance value, e.g., 3:5. Copyright © 2009 John Wiley & Sons, Ltd.     

Shape‐memory behavior of segmented polyurethanes with an amorphous reversible phase: The effect of block length and content

Segmented thermoplastic polyurethanes (TPU)s with amorphous soft segments from the reaction of hexamethylene diisocyanate and 1,2‐butanediol and crystalline hard segments from 4,4′‐methylenediphenyl diisocyanate and 1,6‐hexanediol showed sharp glass‐transition temperatures that could be used as shape‐recovery temperatures. The thermal, mechanical, and shape‐memory effect of these TPUs of various block compositions and lengths were studied by differential scanning calorimetry, dynamic mechanical testing, and tensile testing. As the block lengths decreased, phase mixing increased and hysteresis in the shape‐memory behavior decreased. Too low a content of hard segments increased the hysteresis in the shape‐memory behavior. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2652–2657, 2000     

Shape memory ionomers

This review is focused on the use of ionomers in shape memory polymers. Ionomers are polymers that contain less than ∼15% ionic groups. The incompatibility between the ion-pairs and the polymer backbone drives microphase separation producing dispersed ionic aggregates, which can physically crosslink the polymer. Shape memory polymers are responsive materials that can be deformed to program a temporary shape and then recovered on application of an external stimulus. Through the review of the main types of ionomers used in shape memory polymers, polyurethanes and polyester ionomers, polyolefin and polyaromatic ionomers, and perfluorosulfonic acid ionomers (i.e., Nafion^®) it will be shown that ionomers can produce robust thermoplastic shape memory polymers and in many cases impart unique properties which allow advanced shape memory materials to be obtained including antibacterial, high temperature, and multishape memory polymers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1389–1396     

Preparation of electrospun shape memory polyurethane fibers in optimized electrospinning conditions via response surface methodology

Herein, the electrospinning method, as an effective approach, was utilized to fabricate poly (ε‐caprolactone)‐based polyurethane (PCL‐based PU) fibers. PCL was synthesized by ring‐opening polymerization, and characterized by proton nuclear magnetic resonance (¹H NMR) and Fourier‐transform infrared (FTIR) spectroscopies. Afterward, PU was prepared by step‐growth polymerization. The effects of solution concentration and solvent type on fibers' diameter were investigated. Scanning electron microscopy (SEM) images revealed that the optimum solution was N, N‐dimethylformamide(DMF): chloroform with a ratio of 60:40. In addition, results showed that bead‐less nanofibers could be achieved by a concentration of 5 w/v% (polymer to solvent). Various optimum practical parameters, such as applied voltage, feeding rate, and needle‐to‐collector distance, were obtained and compared with the results of response surface methodology (RSM). On the other hand, the mechanical evaluations indicated that the porous structure of scaffolds caused them to possess lower mechanical properties, as well as shape fixity ratios than those of bulk samples.     

Synthesis and properties of sulfonated polyurethane ionomers with anions in the polyether soft segments

A series of polyether (PTMO, PEO) polyurethane ionomers having different contents of sodium sulfonate groups in the soft segments have been synthesized. The reaction of transesterification was involved in the incorporation of the sodium sulfonate groups in the polyether. The polyurethane ionomers were characterized by means of dynamic mechanical thermal analysis, differential scanning calorimetry, and small-angle x-ray scattering. Solid-state ionic conductivity was also measured. As the ionization level increased, the compatibility of the hard and soft segments increased and the glass transition region of the soft segment became broader. These samples had relatively higher moduli and good film-forming ability. Moreover, this kind of ionomer provides a very promising ionic conductive multiphase polymer with a single ion transport mechanism. © 1997 John Wiley & Sons, Inc.     

Experimental and modeling investigation of shape memory behavior of polyurethane/carbon nanotube nanocomposite

In the current study, mechanical, thermal, thermo‐mechanical, and shape memory behavior of polyurethane/carbon nanotube nanocomposites were investigated, and also a modified Halpin‐Tsai equation was used for the first time to model shape recovery stress of these smart composites. Results showed that strength enhanced with the addition of MWCNTs and improved to a maximum value of 130% for PU‐1wt%CNTs. SEM micrographs were also used to prove the presence of agglomerates at higher CNT contents. By investigating thermogravimetry curves, it was concluded that the incorporation of carbon nanotubes transferred thermal degradation to a higher temperature. Storage modulus improved for nanocomposite samples which showed the reinforcing effect of CNTs on polyurethane. Memory behavior showed that recovery stress was increased for PU‐CNTs samples to a maximum value of 100% and not any harmful effect on shape recoveries observed. Finally, modified Halpin‐Tsai equation was obtained with the correction factor of K = exp(−1.79‐152V_f).