An efficient nonisocyanate route to polyurethanes via thiol‐ene self‐addition

A novel and efficient strategy for the synthesis of nonisocyanate polyurethanes has been developed via thiol–ene self‐photopolymerization. An aliphatic thiol–ene carbamate monomer (allyl(2‐mercaptoethyl)carbamate, AMC) was synthesized by a one‐step synthesis procedure, from cysteamine and allyl chloroformate. The urethane group was therefore incorporated directly into the monomer precursor, avoiding the problems associated to toxic isocyanates. AMC was successfully stabilized with the radical inhibitor pyrogallol (1% wt). In addition, the use of phenyl phosphonic acid as coadditive allowed its stabilization for lower concentrations of pyrogallol (0.1% wt). AMC was directly transformed into thermoplastic polyurethane (TPU) through thiol–ene photopolymerization by UV‐irradiation at 365 nm. The obtained TPU presented semi‐crystalline nature and very high thermal stability (T_5% ～325 °C). It was found that high concentrations of pyrogallol decreased the reaction rate and final conversion of photopolymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3017–3025     

Thiol–ene polymerizations using imide‐based monomers

New diene and dithiol monomers, based on aromatic imides such as benzophenone‐3,3′,4,4′‐tetracarboxylic diimide were synthesized and used in thiol‐ene polymerizations which yield poly(imide‐co‐thioether)s. These linear polymers exhibit limited solubility in various organic solvents. The molecular weights of the polymers were found to decrease with increasing imide content. The glass transition temperature (T_g) of these polymers is dependent on imide content, with T_g values ranging from ?55 °C (with no imide) up to 13 °C (with 70% imide). These thermal property improvements are due to the H‐bonding and rigidity of the aromatic imide moieties. Thermal degradation, as studied by thermogravimetric analysis, was not significantly different to the nonimide containing thiol‐ene polymers made using trimethyloylpropane diallyl ether and 3,5‐dioxa‐1,8‐dithiooctane. It is expected that such monomers may lead to increased glass transition temperatures in other thiol‐ene polymer systems as these normally exhibit low glass transition temperatures. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4637–4642     

Photopolymerization of ternary thiol–ene/acrylate systems: Film and network properties

Photocurable, ternary‐component mixtures of a 1:1 molar multifunctional thiol–ene (trithiol and triallyl ether) blend and a 16‐functional acrylate based monomer have been photopolymerized, and the final film properties of the ternary crosslinked networks have been measured. The photopolymerization kinetics, morphology, and mechanical and physical properties of the films have been investigated with real‐time infrared, atomic force microscopy, and dynamic mechanical analysis. The photopolymerization process is a combination of acrylate homopolymerization and copolymerizations of thiol with allyl ether and acrylate functionalities. The tan δ peaks of the photopolymerized ternary systems are relatively narrow and tunable over a large temperature range. The morphology is characterized by a distinct phase‐separated nanostructure. The photocured thiol–ene/acrylate ternary systems can be made to exhibit good mechanical properties with enhanced energy absorption at room temperature by the appropriate selection of each component concentration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 822–829, 2007.     

Thiourethane‐based thiol‐ene high Tg networks: Preparation,thermal, mechanical,and physical properties

Thiourethane‐based thiol‐ene (TUTE) films were prepared from diisocyanates, tetrafunctional thiols and trienes. The incorporation of thiourethane linkages into the thiol‐ene networks results in TUTE films with high glass transition temperatures. Increases of T_g were achieved by aging at room temperature and annealing the UV cured films at 85 °C. The aged/annealed film with thiol prepared from isophorone diisocyanate and cured with a 10,080‐mJ/cm² radiant exposure had the highest DMA‐based glass transition temperature (108 °C) and a tan δ peak with a full width at half maximum (FWHM) of 22 °C, indicating a very uniform matrix structure. All of the initially prepared TUTE films exhibited good physical and mechanical properties based on pencil hardness, pendulum hardness, impact, and bending tests. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5103–5111, 2007     

Formation of linear and cyclic polyoxetanes in the cationic ring‐opening polymerization of 3‐allyloxymethyl‐3‐ethyloxetane and subsequent postpolymerization modification of poly(3‐allyloxymethyl‐3‐ethyloxetane)

The synthesis of 3‐allyloxymethyl‐3‐ethyloxetane (AllylEHO) and its polymerization with BF₃ × Et₂O is described in this study. Size exclusion chromatography (SEC) and membrane osmometry are used for the determination of molecular weights of the obtained products, ranging from M_n,SEC = 41,500‐131,500 g/mol. ¹H NMR spectroscopy, SEC, as well as MALDI‐TOF MS reveal the formation of cyclic tetramer beside low, but detectable concentrations of larger cyclic oligomers as by‐products during the polymerization process. These results help to understand mechanistically why attempts for a controlled homopolymerization of AllylEHO fail and why a controlled homopolymerization of oxetanes has not been described so far in the literature. Additionally, the high versatility of allyl‐functional polyoxetane for postpolymerization modification is proven by thiol–ene reactions with 3‐mercaptopropionic acid and N‐acetyl‐L ‐cysteine methyl ester. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Partially bio‐based tri‐ and hexaallyl monomers: Synthesis from naturally occurring myo‐inositol and polyaddition with dithiols

myo‐Inositol, a naturally occurring cyclic hexaol, was converted to 2,4,6‐tri‐O‐allyl‐myo‐inositol and 1,2,3,4,5,6‐hexa‐O‐allyl‐myo‐inositol. Polyaddition of the former product, a tri(allyl ether) bearing three hydroxyl groups, with dithiols yielded the corresponding networked polymers. Their glass transition temperatures (T_gs) were higher than those of networked polymers formed by the polyaddition of 1,3,5‐tri‐O‐methyl‐2,4,6‐tri‐O‐allyl‐myo‐inositol. This implied the reinforcement of the networks by hydrogen bonding between the hydroxyl groups. Polyaddition of the latter product, a hexa(allyl ether), with dithiols yielded the corresponding networked polymers with much higher T_gs than those of all of the aforementioned networked polymers. This implied that efficient use of the hexafunctional monomer leads to the formation of more densely crosslinked polymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1524–1529     

Photopolymerization of thiol‐ene systems based on oligomeric thiols

Thiol oligomers were copolymerized with a triallyl ether by a photoinduced polymerization process. These oligomeric thiol‐ene systems comprise the same components as a photopolymerized thiol‐ene‐acrylate ternary system, yet the photopolymerized networks have much lower glass transition temperatures. An investigation into the effect of oligomeric thiol design on network formation was conducted by analyzing the reaction kinetics and thermal/mechanical properties of the thiol‐ene networks. Real‐time FTIR analysis shows that total conversion is >90% for all thiols investigated. Photo‐DSC analysis shows that the maximum exotherm rate is roughly equivalent for all of the thiols when the equivalent weight of the thiol is taken into account. As would be expected, the glass transition temperature and tensile strength increase with thiol functionality and lower thiol equivalent weight for thiols with functionality from 2 to 4. Films made using the oligomeric thiols have essentially the same glass transition temperatures and tensile modulus values regardless of thiol design. These results distinguish the method for generation of networks consisting of an initial Michael reaction of thiols and acrylates followed by a photoinitiated copolymerization with a multifunctional ene from the traditional photolysis of the corresponding thiol‐ene‐acrylate ternary systems with no Michael reaction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 14–24, 2009     

Thiol–norbornene materials: Approaches to develop high Tg thiol–ene polymers

The ability to prepare high T_g low shrinkage thiol–ene materials is attractive for applications such as coatings and dental restoratives. However, thiol and nonacrylated vinyl materials typically consist of a flexible backbone, limiting the utility of these polymers. Hence, it is of importance to synthesize and investigate thiol and vinyl materials of varying backbone chemistry and stiffness. Here, we investigate the effect of backbone chemistry and functionality of norbornene resins on polymerization kinetics and glass transition temperature (T_g) for several thiol–norbornene materials. Results indicate that T_gs as high as 94 °C are achievable in thiol–norbornene resins of appropriately controlled chemistry. Furthermore, both the backbone chemistry and the norbornene moiety are important factors in the development of high T_g materials. In particular, as much as a 70 °C increase in T_g was observed in a norbornene–thiol specimen when compared with a sample prepared using allyl ether monomer of analogous backbone chemistry. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5686–5696, 2007     

One‐pot enzymatic route to tetraallyl ether functional oligoesters: Synthesis,UV curing,and characterization

An enzymatic one‐pot route in bulk was used to synthesize tetraallyl ether (tAE) functional oligomers based on divinyl adipate, 1,4‐butanediol and trimethylolpropane diallyl ether. By using lipase B from Candida antarctica as catalyst and varying the stoichiometric ratio of monomers, it was possible to reach targeted molecular weights (from 1300 to 3300 g mol^?1) of allyl‐ether functional polyesters. The enzyme catalyzed reaction reached completion (>98% conversion based on all monomers) within 24 h at 60 °C, under reduced pressure (72 mbar) resulting in ～90% yield after filtration. The tAE‐functional oligoesters were photopolymerized, without any purification other than removal of the enzyme by filtration, with thiol functional monomers (dithiol, tetrathiol) in a 1:1 ratio thiol‐ene reaction. The photo‐initiator, 2,2‐dimethoxy‐2‐phenylacetophenone, was used to improve the rate of reaction under UV light. High conversions (96–99% within detection limits) were found for all thiol‐ene films as determined by FT‐Raman spectroscopy. The tAE‐functional oligoesters were characterized by NMR, MALDI, and SEC. The UV‐cured homopolymerized films and the thiol‐ene films properties were characterized utilizing DSC and DMTA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

Thiol‐ene clickable hyperscaffolds bearing peripheral allyl groups

Radical catalyzed thiol‐ene reaction has become a useful alternative to the Huisgen‐type click reaction as it helps to expand the variability in reaction conditions as well as the range of clickable entities. Thus, direct generation of hyperbranched polymers bearing peripheral allyl groups that could be clicked using a variety of functional thiols would be of immense value. A specifically designed AB₂ type monomer, that carries two allyl benzyl ethers groups and one alcohol functionality, was shown to undergo self‐condensation under acid‐catalyzed melt‐transetherification to yield a hyperbranched polyether that carries numerous allyl end‐groups. Importantly, it was shown that the kinetics of polymerization is not dramatically affected by the change of the ether unit from previously studied methyl benzyl ether to an allyl benzyl ether. The peripheral allyl groups were readily clicked quantitatively, using a variety of thiols, to generate an hydrocarbon‐soluble octadecyl‐derivative, amphiphilic systems using 2‐mercaptoethanol and chiral amino acid (N‐benzoyl cystine) derivatized hyperbranched structures; thus demonstrating the versatility of this novel class of clickable hyperscaffolds. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Design and synthesis of highly photopolymerizable styrenyl compounds in solid‐state photoinitiated polymerization

We designed a new type of styrenyl compound applicable to conventional photopolymerization systems, aiming at the production of polymers with improved mechanical properties, resistance to chemicals, and elevated glass‐transition temperatures (T_g's). A series of styrenyl monomers bearing 2,5‐dithio‐1,3,4‐thiadiazole groups were prepared, and their reactivity was studied in solid‐state photopolymerization initiated by 2‐(4′‐methoxystyryl)‐4,6‐bis(trichloromethyl)‐1,3,5‐triazine. These monomers exhibited much higher polymerization rates than usual, and the final conversion nearly reached completion, despite the relatively high T_g of the solid‐state photopolymerization system. Even at temperatures below T_g, the polymerization proceeded without a ceiling phenomenon. These features were explained by intermolecular interactions between the monomers that induced monomer alignments effective for solid‐state polymerization, large excess free volumes arising from rotation around the methylthio groups, and intramatrix radical migration leading to encounters with the remaining monomers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3227–3242, 2003     

Photopolymerization behavior in nanocomposites formed with thiol–acrylate and polymerizable organoclays

Because of the inherent characteristics of the thiol–ene step growth mechanism in preparation of thiol–ene photopolymer clay nanocomposites, the ratio between thiol and ene functional groups at and near the organoclay surfaces may have a significant effect on the polymerization behavior. This study investigates the influence of monomer composition and the type of polymerizable organoclay on thiol–acrylate photopolymerization behavior in preparation of photocurable clay nanocomposite systems. To this end, two types of polymerizable organoclays with acrylate or thiol functional group on the clay surfaces were compared in monomer compositions with different polarity and functionality. Real‐time infrared spectroscopy was used to characterize polymerization behavior in conjunction with photo‐DSC. The degree of clay exfoliation was evaluated using small angle X‐ray scattering and correlated with photopolymerization behavior. Higher chemical compatibility of components induced enhanced clay exfoliation resulting in increase in photopolymerization rate. By affecting the stoichiometric ratio of functional groups in the clay gallery, thiolated organoclays enhance thiol–ene reaction, whereas acrylated organoclays encourage acrylate homopolymerization. In addition, inducing more propagating thiyl radicals on the organoclay surfaces by increasing functionality of thiol monomer also facilitates thiol–ene copolymerization, whereas the increase of acrylate functionality reduces final thiol conversion. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Silicon‐based mercaptans: High‐performance monomers for thiol‐ene photopolymerization

Ester‐free silane and siloxane‐based thiol monomers were successfully synthesized and evaluated for application in thiol‐ene resins. Polymerization reaction rates, conversion, network properties as well as degradation experiments of those thiol monomers in combination with triallyl‐1,3,5‐triazine‐2,4,6(1H,3H,5H)‐trione (TATT) as ene component were performed and compared with formulations containing the commercially available mercaptopropionic ester‐based thiol pentaerythritol tetra‐3‐mercaptopropionate. Kinetic analysis revealed appropriate reaction rates and conversions reaching 90% and higher. Importantly, storage stability tests of those formulations clearly indicate the superiority of the synthesized mercaptans compared with pentaerythritol tetra‐3‐mercaptopropionate/TATT resins. Moreover, photocured samples containing silane‐based mercaptans provide higher glass transition temperatures and withstand water storage without a significant loss in their network properties. This behavior together with the observed excellent degradation resistance of photocured silane‐based thiol/TATT formulations make these multifunctional mercaptans interesting candidates for high‐performance applications, such as dental restoratives and automotive resins. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 418–424     

Synthesis and thiol–ene photopolymerization of allyl‐ether functionalized dendrimers

Well‐defined, allyl‐ether functional, first‐generation dendrimers have been synthesized. The convergent growth approach was utilized, using the anhydride of the allyl‐ether terminated building block. Three different core moieties were used: trimethylolpropane, trisphenol, and ditrimethylolpropane. The coupling reactions proceeded in good yields and all compounds were characterized by NMR, MALDI‐TOF, and SEC. The allyl‐terminated dendrimers were crosslinked by thiol–ene chemistry, using a multifunctional thiol, TriThiol, to give clear and smooth films. The photopolymerization was conducted in the presence of a photoinitiator, Irgacure 651, and no traces of either allyl‐ether groups or thiols were observed by FT‐Raman after cure. All crosslinked films were characterized with respect to mechanical (DMA) and thermal (DSC) properties. It was found that homogeneous networks were formed and that the core functionality and structure had little effect on the network properties. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1339–1348, 2008     

High solubility,low‐dielectric constant,and optical transparency of novel polyimides derived from 3,3′,5,5′‐tetramethyl‐4,4′‐diaminodiphenyl‐4″‐isopropyltoluene

A series of novel polyimides (PIs) ( 3a–d ) were prepared from 3,3′,5,5′‐tetramethyl‐4,4′‐diaminodiphenyl‐4 ″ ‐isopropyltoluene ( 1 ) with four aromatic dianhydrides via a one‐step high temperature polycondensation procedure. The obtained PIs showed excellent solubility, with most of them dissoluble at a concentration of 10 wt % in amide polar solvents and chlorinated solvents. Their films were nearly colorless and exhibited high‐optical transparency, with the UV cutoff wavelength in the range of 328–353 nm and the transparency at 450 nm >80%. They also showed low‐dielectric constant (2.49–2.94 at 1 MHz) and low‐water absorptions (0.44–0.65%). Moreover, these PIs possessed high‐glass transition temperatures (T_g) beyond 327 °C and excellent thermal stability with 10% weight loss temperatures in the range of 530–555 °C in nitrogen atmosphere. In comparison with some fluorinated poly(ether imide)s derived from the trifluoromethyl‐substituted bis(ether amine)s, the resultant PIs 3a–d showed better solubility, lower cutoff wavelength, and higher T_g. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3309–3317, 2009     

Synthesis of new fluorinated allyl ethers for the surface modification of thiol–ene ultraviolet‐curable formulations

Thiol–ene photocurable systems based on a trifunctional thiol [trimethylolpropane tris‐(3‐mercaptopropanoate)] and two different multifunctional allyl ethers (trimethylolpropane triallyl ether and Boltorn U2, an allyl functional dendritic polyester) were examined. To these systems, small amounts (<1 wt %) of fluorinated allyl ethers were added for the modification of their surface properties. Two new fluorinated allyl ethers, 1H,1H‐perfluoro‐1‐heptylallyl ether and 1H,1H‐perfluoro‐1‐decylallyl ether, were synthesized for this purpose by allylation of the corresponding 1H,1H‐perfluoro alcohols. The fluorinated monomers, despite their very low concentrations, caused sharp changes in the surface properties of the films and in the solvent resistance without any changes in the curing conditions and bulk properties. Completely hydrophobic surfaces were obtained (as a result of the selective enrichment of the fluorinated monomers on the film surfaces) that depended on the monomer structure and its concentration. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2583–2590, 2002     

L‐arabinitol‐based functional polyurethanes

Three new polymerizable diols, based on mono‐, di‐, and tri‐O‐allyl‐L ‐arabinitol derivatives, were prepared from L ‐arabinitol as versatile materials for the preparation of tailor‐made polyurethanes with varied degrees of functionalization. Their allyl functional groups can take part in thiol‐ene reactions, to obtain greatly diverse materials. This “click” reaction with 2‐mercaptoethanol was firstly studied on the highly hindered sugar precursor 2,3,4‐tri‐O‐allyl‐1,5‐di‐O‐trityl‐L ‐arabinitol, to apply it later to macromolecules. A polyurethane with multiple pendant allyl groups was synthesized by polyaddition reaction of 2,3,4‐tri‐O‐allyl‐L ‐arabinitol with 1,6‐hexamethylene diisocyanate, and then functionalized by thiol‐ene reaction. The coupling reaction took place in every allyl group, as confirmed by standard techniques. The thermal stability of the novel polyurethanes was investigated by thermogravimetric analysis and differential scanning calorimetry (DSC). This strategy provides a simple and versatile platform for the design of new materials whose functionality can be easily modified. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Bis‐hydrophilic and functional triblock terpolymers based on polyethers: Synthesis and self‐assembly in solution

A well‐defined triblock terpolymer, poly(ethylene glycol)‐block‐poly(allyl glycidyl ether)‐block‐poly(tert‐butyl glycidyl ether) (PEG‐b‐PAGE‐b‐Pt‐BGE), with a narrow molar mass distribution has been synthesized by sequential living anionic ring‐opening polymerization. Afterward, the PAGE block was modified via thiol‐ene chemistry and different sugar moieties or cysteine as a model compound for peptides could be covalently attached to the polymer backbone. The solution self‐assembly of the obtained bis‐hydrophilic triblock terpolymers in aqueous media has been studied in detail by turbidimetry, dynamic light scattering, and transmission electron microscopy (TEM and cryo‐TEM). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of water‐soluble allyl‐functionalized oligochitosan and its modification by thiol–ene addition in water

A novel, straightforward and versatile chemical pathway has been studied to functionalize water‐soluble chitosan oligomers. This metal‐free methodology is based on the epoxy‐amine reaction of the allyl glycidyl ether with chitosan, followed by thiol‐ene radical coupling reaction of ω‐functional mercaptans, using 4,4′‐Azobis(4‐cyanovaleric acid) as a free radical initiator. Both reactions were entirely carried out in water. In a preliminary step, chitosan depolymerization was carried out using H₂O₂ in an acetic medium under 100 W microwave irradiation, optimizing the yield of water‐soluble oligomers. Functionalization by six different thiols bearing alcohol, carboxylic acid, ester, and amino groups was then performed, leading to a range of functional oligochitosans with different grafting efficiencies. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 39–48